Professional Documents
Culture Documents
2% PERFORMANCECHARACTERISTICS
Model No.
________
Generator Foam
Solution
Inlet Pressure Output
Flow
psi
(bar)
cfm
(cmm)
gpm
(Lpm)
Expansion
___________ _____________
____________
_________
JET-X-2A
35 (132)
42 (159)
50 (189)
468:1
486:1
450:1
JET-X-5A
61 (231)
75 (284)
87 (329)
816:1
936:1
916:1
JET-X-15A 40
(UL)
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
12,121 (343)
14,491 (410)
19,141 (542)
21,796 (617)
108
119
145
169
(409)
(450)
(549)
(640)
840:1
911:1
987:1
965:1
180 (681)
220 (833)
260 (984)
538:1
604:1
561:1
JET-X-20
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
13,530 (383)
14,746 (418)
19,007 (538)
22,598 (640)
212 (803)
238 (901)
294 (1,113)
338 (1,279)
477:1
463:1
484:1
500:1
JET-X-27
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
20,295 (575)
23,965 (679)
27,303 (773)
28,802 (816)
181 (685)
203 (768)
243 (920)
276 (1,045)
839:1
883:1
840:1
781:1
Application
ANSUL electric actuated dampers and louvers are available when
the use of outside air is required to generate a high-expansion foam
blanket. These devices are especially suited for total flooding highexpansion foam systems where combustion products (smoke and soot)
and heat produced from the material(s) involved would inhibit foam
production. In warmer climates, air exchange may be unnecessary, and
actuated dampers and louvers may not be required. However, in cold
weather climates, they may be mandatory to reduce building heat loss
during winter c onditions.
JET-X HIGH-EXPANSIONFOAMGENERATORS
Description
The ANSUL actuated dampers and louvers are powered by 110 VAC
and are fail-safe open devices. Energized, the damper or louver is
closed with loss of power to open. They are available with either NEMA
4 or NEMA 7 actuators.
Data/Specifications
Air intake dampers are available for wall or roof mounting. The wall
mount damper is a complete package inclusive of the damper with
actuator, weatherhood with birdscreen, and transition piece to intake
of generator. The roof mount damper includes the same features as
the wall mount damper as well as roof curbing. Wall relief louvers are
comprised only of a louver with actuator and birdscreen. Wall relief
louvers are not required where adequate venting exists.
FEATURES
BENEFITS
n FMApproved Models
WALL
D
Transition
(Round)
A, B
ROOF
TABLE 2
NOTES:
DESCRIPTION
D Transition
(Round)
A, B
E
006372
2 3/4% PERFORMANCECHARACTERISTICS
1
Model No.
________
Generator Foam
Solution
Inlet Pressure Output
Flow
psi
(bar)
cfm
(cmm)
gpm
(Lpm)
Expansion
___________ _____________
____________
_________
JET-X-2A
35 (132)
42 (159)
50 (189)
454:1
496:1
473:1
JET-X-5A
50 (3.4)
75 (5.2)
100 (6.9)
61 (231)
75 (284)
87 (329)
684:1
661:1
617:1
5,575 (158)
6,628 (188)
7,182 (203)
119 (450)
145 (549)
169 (640)
180 (681)
220 (833)
260 (984)
JET-X-20
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
13,443 (381)
16,034 (454)
21,145 (599)
24,301 (688)
212 (803)
238 (901)
294 (1,113)
338 (1,279)
708:1
799:1
816:1
488:1
545:1
564:1
474:1
504:1
538:1
538:1
TABLE 3
NOTE:
1.JET-X 2% and JET-X 2 3/4% concentrates are not to be mixed for normal system operation.
001273
96 in.
(2438 mm)
Application
26 in.
(660 mm)
Depending on the type of hazard and its configuration, a JET-X HighExpansion Foam System may be designed for total flooding or local
application. Common applications suited for high-expansion foam
include:
n Aircraft Hangars
54 in.
(1372 mm)
60 in.
(1524 mm)
1.5 IN.
(38 mm)
006372b
ORDERINGINFORMATION DIMENSIONS
Clearance Dimensions*
Shipping
Part No.
A
B
C
D
E
Weights**
NEMA
4 / 7
Model
in. (mm) _________ _________
in. (mm) in. (mm) _________
in. (mm) _________
in. (mm) lb
(kg)
____________
_____
_________
________
430060/430061 Wall Intake Damper Assembly JET-X-5A
44.0 (1118) 44.0 (1118) 24.0 (610) 42.0 (1060) 51.8 (1314) 241 (109)
430062/430063 Roof Intake Damper Assembly JET-X-5A
46.0 (1168) 46.0 (1168) 16.0 (406) 42.0 (1067) 57.8 (1467) 285 (129)
430064/430065 Wall Relief Louver Assembly JET-X-5A
30.0 (762) 48.0 (1219) 6.0 (152)
50 (23)
430066/430067 Wall Intake Damper Assembly JET-X-15/20/27 54.0 (1372) 54.0 (1372) 24.0 (610) 53.0 (1340) 57.9 (1470) 315 (143)
430068/430069 Roof Intake Damper Assembly JET-X-15/20
54.0 (1372) 54.0 (1372) 16.0 (406) 53.0 (1346) 65.8 (1670) 360 (164)
430070/430071 Wall Relief Louver Assembly JET-X-15/20/27 60.0 (1524) 84.0 (2134) 6.0 (152)
140 (64)
437018/437097 Roof Intake Damper Assembly JET-X-27
54.0 (1372) 54.0 (1372) 14.0 (356) 53.0 (1346) 62.5 (1588) 525 (238)
* Actual dimensions of equipment will be approximately 0.25 in. (6.4 mm) smaller than clearance dimensions listed. TABLE 5
** Weights listed are for NEMA 4 models; add 20 lb (9.1 kg) for NEMA 7 models.
NOTE: The converted metric values in this document are provided for dimensional reference only and do not reflect an actual measurement.
+1-715-735-7411
www.ansul.com
n Power Stations
n Cable Tunnels
Foam Screen
Blower Fan
Water
Motor
n Transformer Rooms
n Basements, Cellars and Enclosed Spaces
n Communications Switching Stations
In addition to the above hazard types involving Class A and B fires,
high-expansion foam is effective in controlling Liquefied Natural Gas
(LNG) fires by blocking heat feedback from the flames to the LNG
thereby reducing the vaporization rate.
Air
Flow
Foam
Foam
Solution
Inlet
Foam Solution
Spray
001274
SPECIFICATIONS
Where required, the foam generator shall be powered by a water reaction motor. The water reaction motor shall provide both the screen
wetting solution and the energy to drive the fan.
The foam generator shall not require any outside power source, such as
electricity or gasoline engines.
All foam generators designed for fixed installations shall be equipped
with a stainless steel screen for maximum reliability under fire
conditions.
The proportioning system normally used for a high-expansion foam
system shall be of the balanced pressure type utilizing a bladder tank
and proportioner to provide metering accuracy with minimal loss of available pressure from the water supply.
ft3
(850
m3)
Model
_____
E*
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
NPT in. __________ __________ ________
in.
(mm) in.
(mm)
in. (mm)
____________ _____________
__________
___________
________
JET-X-2A
25.0 (635)
25.0 (635)
30.1 (764) 3.9 (99)
1
JET-X-5A
44.5
(1130) 42.1
(1069) 40.3
(1024)
6.4
(154) 1 1/2
JET-X-15A (UL) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-15A (FM) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-15A (LNG) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-20
64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
16.0 (406)
3.3 (83)
27.0
(686)
18.5
(470) 6.1
(156)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
* Most units are available with rear and side inlets. Exception: JET-X-15A (LNG) and JET-X-20 are rear inlet only.
JET-X-5A
13.8 in.
(348 mm)
63.2 in.
(1607 mm)
TOP View
5.0 in.
(127 mm)
2 IN.
NPT*
D
A
24.1 in.
(613
mm)
32.2 in.
(819 mm)
008769
008770
Metric:
R = ([2803 m3 / 1 min] + 241 cmm) x 1.15 x 1.
= 3044 x 1.15 x 1.2
= 4201 cubic meters per minute (cmm) minimum required
92.8 in.
(2357 mm)
SIDE VIEW
13.8 in.
(348 mm)
44.9 in.
(1143 mm)
5.0 in.
(127 mm)
APPROVALS
High-expansion foam systems are designed in accordance with
NFPA11 Standard for Low, Medium and High-Expansion Foam
Systems, which requires that the high-expansion generator(s) be listed
or approved together with the type of high-expansion foam concentrate
used. The JET-X generators carry the listings as indicated in Table 1.
008417
ORDERINGINFORMATION
Stainless Steel*:
471066 JET-X 2A 73 (33)
436936 JET-X-5A
255 (116)
436878 JET-X-15A (UL)
398 (180)
472526 JET-X-15A(LNG) 398 (180)
471871 JET-X-20
397 (180)
*Stainless Steel Housing and Motor Brackets
001275
D
A
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
E
006371
TABLE 1
C
Side View
60.8 in.
(1543 mm)
Side View
36.0 in.
(914 mm)
Unit
Weights
2 3/4%
2%
Part
No. Model
lb (kg)
Approval
Approval
_______________________________________________________
420001 JET-X-2A 73 (33) UL, CE
UL, CE
420003 JET-X-5A
255 (116) UL, FM, CE UL, CE
420005 JET-X-15A (UL)
397 (180) UL, CE
UL, CE
420006 JET-X-15A (FM)
397 (180) FM, CE
CE
420007 JET-X-15A (LNG) 397 (180) UL, CE
UL, CE
421590 JET-X-20
397 (180) UL, CE
UL, CE
436899 JET-X-27
720 (327) CE
UL, CE
40.0 in.
(1016 mm)
G
Top and Bottom View
Mounting Hole Locations
SPECIFICATIONS
Where required, the foam generator shall be powered by a water reaction motor. The water reaction motor shall provide both the screen
wetting solution and the energy to drive the fan.
The foam generator shall not require any outside power source, such as
electricity or gasoline engines.
All foam generators designed for fixed installations shall be equipped
with a stainless steel screen for maximum reliability under fire
conditions.
The proportioning system normally used for a high-expansion foam
system shall be of the balanced pressure type utilizing a bladder tank
and proportioner to provide metering accuracy with minimal loss of available pressure from the water supply.
ft3
(850
m3)
Model
_____
E*
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
NPT in. __________ __________ ________
in.
(mm) in.
(mm)
in. (mm)
____________ _____________
__________
___________
________
JET-X-2A
25.0 (635)
25.0 (635)
30.1 (764) 3.9 (99)
1
JET-X-5A
44.5
(1130) 42.1
(1069) 40.3
(1024)
6.4
(154) 1 1/2
JET-X-15A (UL) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-15A (FM) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-15A (LNG) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-20
64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
16.0 (406)
3.3 (83)
27.0
(686)
18.5
(470) 6.1
(156)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
* Most units are available with rear and side inlets. Exception: JET-X-15A (LNG) and JET-X-20 are rear inlet only.
JET-X-5A
13.8 in.
(348 mm)
63.2 in.
(1607 mm)
TOP View
5.0 in.
(127 mm)
2 IN.
NPT*
D
A
24.1 in.
(613
mm)
32.2 in.
(819 mm)
008769
008770
Metric:
R = ([2803 m3 / 1 min] + 241 cmm) x 1.15 x 1.
= 3044 x 1.15 x 1.2
= 4201 cubic meters per minute (cmm) minimum required
92.8 in.
(2357 mm)
SIDE VIEW
13.8 in.
(348 mm)
44.9 in.
(1143 mm)
5.0 in.
(127 mm)
APPROVALS
High-expansion foam systems are designed in accordance with
NFPA11 Standard for Low, Medium and High-Expansion Foam
Systems, which requires that the high-expansion generator(s) be listed
or approved together with the type of high-expansion foam concentrate
used. The JET-X generators carry the listings as indicated in Table 1.
008417
ORDERINGINFORMATION
Stainless Steel*:
471066 JET-X 2A 73 (33)
436936 JET-X-5A
255 (116)
436878 JET-X-15A (UL)
398 (180)
472526 JET-X-15A(LNG) 398 (180)
471871 JET-X-20
397 (180)
*Stainless Steel Housing and Motor Brackets
001275
D
A
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
E
006371
TABLE 1
C
Side View
60.8 in.
(1543 mm)
Side View
36.0 in.
(914 mm)
Unit
Weights
2 3/4%
2%
Part
No. Model
lb (kg)
Approval
Approval
_______________________________________________________
420001 JET-X-2A 73 (33) UL, CE
UL, CE
420003 JET-X-5A
255 (116) UL, FM, CE UL, CE
420005 JET-X-15A (UL)
397 (180) UL, CE
UL, CE
420006 JET-X-15A (FM)
397 (180) FM, CE
CE
420007 JET-X-15A (LNG) 397 (180) UL, CE
UL, CE
421590 JET-X-20
397 (180) UL, CE
UL, CE
436899 JET-X-27
720 (327) CE
UL, CE
40.0 in.
(1016 mm)
G
Top and Bottom View
Mounting Hole Locations
SPECIFICATIONS
Where required, the foam generator shall be powered by a water reaction motor. The water reaction motor shall provide both the screen
wetting solution and the energy to drive the fan.
The foam generator shall not require any outside power source, such as
electricity or gasoline engines.
All foam generators designed for fixed installations shall be equipped
with a stainless steel screen for maximum reliability under fire
conditions.
The proportioning system normally used for a high-expansion foam
system shall be of the balanced pressure type utilizing a bladder tank
and proportioner to provide metering accuracy with minimal loss of available pressure from the water supply.
ft3
(850
m3)
Model
_____
E*
in.
(mm)
in.
(mm)
in.
(mm)
in.
(mm)
NPT in. __________ __________ ________
in.
(mm) in.
(mm)
in. (mm)
____________ _____________
__________
___________
________
JET-X-2A
25.0 (635)
25.0 (635)
30.1 (764) 3.9 (99)
1
JET-X-5A
44.5
(1130) 42.1
(1069) 40.3
(1024)
6.4
(154) 1 1/2
JET-X-15A (UL) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-15A (FM) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-15A (LNG) 64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
JET-X-20
64.0
(1629) 64.0
(1629) 46.0
(1178)
8.5
(219) 2
16.0 (406)
3.3 (83)
27.0
(686)
18.5
(470) 6.1
(156)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
36.0
(914)
5.0
(127) 8.0
(213)
* Most units are available with rear and side inlets. Exception: JET-X-15A (LNG) and JET-X-20 are rear inlet only.
JET-X-5A
13.8 in.
(348 mm)
63.2 in.
(1607 mm)
TOP View
5.0 in.
(127 mm)
2 IN.
NPT*
D
A
24.1 in.
(613
mm)
32.2 in.
(819 mm)
008769
008770
Metric:
R = ([2803 m3 / 1 min] + 241 cmm) x 1.15 x 1.
= 3044 x 1.15 x 1.2
= 4201 cubic meters per minute (cmm) minimum required
92.8 in.
(2357 mm)
SIDE VIEW
13.8 in.
(348 mm)
44.9 in.
(1143 mm)
5.0 in.
(127 mm)
APPROVALS
High-expansion foam systems are designed in accordance with
NFPA11 Standard for Low, Medium and High-Expansion Foam
Systems, which requires that the high-expansion generator(s) be listed
or approved together with the type of high-expansion foam concentrate
used. The JET-X generators carry the listings as indicated in Table 1.
008417
ORDERINGINFORMATION
Stainless Steel*:
471066 JET-X 2A 73 (33)
436936 JET-X-5A
255 (116)
436878 JET-X-15A (UL)
398 (180)
472526 JET-X-15A(LNG) 398 (180)
471871 JET-X-20
397 (180)
*Stainless Steel Housing and Motor Brackets
001275
D
A
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
UL, CE
E
006371
TABLE 1
C
Side View
60.8 in.
(1543 mm)
Side View
36.0 in.
(914 mm)
Unit
Weights
2 3/4%
2%
Part
No. Model
lb (kg)
Approval
Approval
_______________________________________________________
420001 JET-X-2A 73 (33) UL, CE
UL, CE
420003 JET-X-5A
255 (116) UL, FM, CE UL, CE
420005 JET-X-15A (UL)
397 (180) UL, CE
UL, CE
420006 JET-X-15A (FM)
397 (180) FM, CE
CE
420007 JET-X-15A (LNG) 397 (180) UL, CE
UL, CE
421590 JET-X-20
397 (180) UL, CE
UL, CE
436899 JET-X-27
720 (327) CE
UL, CE
40.0 in.
(1016 mm)
G
Top and Bottom View
Mounting Hole Locations
HIGH-EXPANSIONLOUVERS/DAMPERS
2% PERFORMANCECHARACTERISTICS
Model No.
________
Generator Foam
Solution
Inlet Pressure Output
Flow
psi
(bar)
cfm
(cmm)
gpm
(Lpm)
Expansion
___________ _____________
____________
_________
JET-X-2A
35 (132)
42 (159)
50 (189)
468:1
486:1
450:1
JET-X-5A
61 (231)
75 (284)
87 (329)
816:1
936:1
916:1
JET-X-15A 40
(UL)
50
75
100
(409)
(450)
(549)
(640)
840:1
911:1
987:1
965:1
180 (681)
220 (833)
260 (984)
538:1
604:1
561:1
JET-X-20
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
13,530 (383)
14,746 (418)
19,007 (538)
22,598 (640)
212 (803)
238 (901)
294 (1,113)
338 (1,279)
477:1
463:1
484:1
500:1
JET-X-27
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
20,295 (575)
23,965 (679)
27,303 (773)
28,802 (816)
181 (685)
203 (768)
243 (920)
276 (1,045)
839:1
883:1
840:1
781:1
(2.8)
(3.4)
(5.2)
(6.9)
12,121 (343)
14,491 (410)
19,141 (542)
21,796 (617)
108
119
145
169
TABLE 2
Application
ANSUL electric actuated dampers and louvers are available when
the use of outside air is required to generate a high-expansion foam
blanket. These devices are especially suited for total flooding highexpansion foam systems where combustion products (smoke and soot)
and heat produced from the material(s) involved would inhibit foam
production. In warmer climates, air exchange may be unnecessary, and
actuated dampers and louvers may not be required. However, in cold
weather climates, they may be mandatory to reduce building heat loss
during winter c onditions.
Air intake dampers are available for wall or roof mounting. The wall
mount damper is a complete package inclusive of the damper with
actuator, weatherhood with birdscreen, and transition piece to intake
of generator. The roof mount damper includes the same features as
the wall mount damper as well as roof curbing. Wall relief louvers are
comprised only of a louver with actuator and birdscreen. Wall relief
louvers are not required where adequate venting exists.
454:1
496:1
473:1
JET-X-5A
50 (3.4)
75 (5.2)
100 (6.9)
5,575 (158)
6,628 (188)
7,182 (203)
61 (231)
75 (284)
87 (329)
684:1
661:1
617:1
119 (450)
145 (549)
169 (640)
708:1
799:1
816:1
180 (681)
220 (833)
260 (984)
488:1
545:1
564:1
JET-X-20
212 (803)
238 (901)
294 (1,113)
338 (1,279)
474:1
504:1
538:1
538:1
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
13,443 (381)
16,034 (454)
21,145 (599)
24,301 (688)
TABLE 3
NOTE:
1.JET-X 2% and JET-X 2 3/4% concentrates are not to be mixed for normal system operation.
DESCRIPTION
D Transition
(Round)
A, B
E
1.5 IN.
(38 mm)
006372
2 3/4% PERFORMANCECHARACTERISTICS
35 (132)
42 (159)
50 (189)
2.JET-X 2% and JET-X 2 3/4% concentrates are not to be mixed for normal system operation.
JET-X-2A
BENEFITS
D
Transition
(Round)
A, B
Generator Foam
Solution
Inlet Pressure Output
Flow
psi
(bar)
cfm
(cmm)
gpm
(Lpm)
Expansion
___________ _____________
____________
_________
FEATURES
n FMApproved Models
WALL
NOTES:
Model No.
________
Data/Specifications
Description
The ANSUL actuated dampers and louvers are powered by 110 VAC
and are fail-safe open devices. Energized, the damper or louver is
closed with loss of power to open. They are available with either NEMA
4 or NEMA 7 actuators.
ROOF
JET-X HIGH-EXPANSIONFOAMGENERATORS
001273
96 in.
(2438 mm)
Application
26 in.
(660 mm)
Depending on the type of hazard and its configuration, a JET-X HighExpansion Foam System may be designed for total flooding or local
application. Common applications suited for high-expansion foam
include:
n Aircraft Hangars
54 in.
(1372 mm)
60 in.
(1524 mm)
1.5 IN.
(38 mm)
008446
006372b
ORDERINGINFORMATION DIMENSIONS
Clearance Dimensions*
Shipping
Part No.
A
B
C
D
E
Weights**
NEMA
4 / 7
Model
in. (mm) _________ _________
in. (mm) in. (mm) _________
in. (mm) _________
in. (mm) lb
(kg)
____________
_____
_________
________
430060/430061 Wall Intake Damper Assembly JET-X-5A
44.0 (1118) 44.0 (1118) 24.0 (610) 42.0 (1060) 51.8 (1314) 241 (109)
430062/430063 Roof Intake Damper Assembly JET-X-5A
46.0 (1168) 46.0 (1168) 16.0 (406) 42.0 (1067) 57.8 (1467) 285 (129)
430064/430065 Wall Relief Louver Assembly JET-X-5A
30.0 (762) 48.0 (1219) 6.0 (152)
50 (23)
430066/430067 Wall Intake Damper Assembly JET-X-15/20/27 54.0 (1372) 54.0 (1372) 24.0 (610) 53.0 (1340) 57.9 (1470) 315 (143)
430068/430069 Roof Intake Damper Assembly JET-X-15/20
54.0 (1372) 54.0 (1372) 16.0 (406) 53.0 (1346) 65.8 (1670) 360 (164)
430070/430071 Wall Relief Louver Assembly JET-X-15/20/27 60.0 (1524) 84.0 (2134) 6.0 (152)
140 (64)
437018/437097 Roof Intake Damper Assembly JET-X-27
54.0 (1372) 54.0 (1372) 14.0 (356) 53.0 (1346) 62.5 (1588) 525 (238)
* Actual dimensions of equipment will be approximately 0.25 in. (6.4 mm) smaller than clearance dimensions listed. TABLE 5
** Weights listed are for NEMA 4 models; add 20 lb (9.1 kg) for NEMA 7 models.
NOTE: The converted metric values in this document are provided for dimensional reference only and do not reflect an actual measurement.
+1-715-735-7411
www.ansul.com
n Power Stations
n Cable Tunnels
Foam Screen
Water
Motor
n Transformer Rooms
Blower Fan
Air
Flow
Foam
Foam
Solution
Inlet
Foam Solution
Spray
001274
HIGH-EXPANSIONLOUVERS/DAMPERS
2% PERFORMANCECHARACTERISTICS
Model No.
________
Generator Foam
Solution
Inlet Pressure Output
Flow
psi
(bar)
cfm
(cmm)
gpm
(Lpm)
Expansion
___________ _____________
____________
_________
JET-X-2A
35 (132)
42 (159)
50 (189)
468:1
486:1
450:1
JET-X-5A
61 (231)
75 (284)
87 (329)
816:1
936:1
916:1
JET-X-15A 40
(UL)
50
75
100
(409)
(450)
(549)
(640)
840:1
911:1
987:1
965:1
180 (681)
220 (833)
260 (984)
538:1
604:1
561:1
JET-X-20
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
13,530 (383)
14,746 (418)
19,007 (538)
22,598 (640)
212 (803)
238 (901)
294 (1,113)
338 (1,279)
477:1
463:1
484:1
500:1
JET-X-27
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
20,295 (575)
23,965 (679)
27,303 (773)
28,802 (816)
181 (685)
203 (768)
243 (920)
276 (1,045)
839:1
883:1
840:1
781:1
(2.8)
(3.4)
(5.2)
(6.9)
12,121 (343)
14,491 (410)
19,141 (542)
21,796 (617)
108
119
145
169
TABLE 2
Application
ANSUL electric actuated dampers and louvers are available when
the use of outside air is required to generate a high-expansion foam
blanket. These devices are especially suited for total flooding highexpansion foam systems where combustion products (smoke and soot)
and heat produced from the material(s) involved would inhibit foam
production. In warmer climates, air exchange may be unnecessary, and
actuated dampers and louvers may not be required. However, in cold
weather climates, they may be mandatory to reduce building heat loss
during winter c onditions.
Air intake dampers are available for wall or roof mounting. The wall
mount damper is a complete package inclusive of the damper with
actuator, weatherhood with birdscreen, and transition piece to intake
of generator. The roof mount damper includes the same features as
the wall mount damper as well as roof curbing. Wall relief louvers are
comprised only of a louver with actuator and birdscreen. Wall relief
louvers are not required where adequate venting exists.
454:1
496:1
473:1
JET-X-5A
50 (3.4)
75 (5.2)
100 (6.9)
5,575 (158)
6,628 (188)
7,182 (203)
61 (231)
75 (284)
87 (329)
684:1
661:1
617:1
119 (450)
145 (549)
169 (640)
708:1
799:1
816:1
180 (681)
220 (833)
260 (984)
488:1
545:1
564:1
JET-X-20
212 (803)
238 (901)
294 (1,113)
338 (1,279)
474:1
504:1
538:1
538:1
40
50
75
100
(2.8)
(3.4)
(5.2)
(6.9)
13,443 (381)
16,034 (454)
21,145 (599)
24,301 (688)
TABLE 3
NOTE:
1.JET-X 2% and JET-X 2 3/4% concentrates are not to be mixed for normal system operation.
DESCRIPTION
D Transition
(Round)
A, B
E
1.5 IN.
(38 mm)
006372
2 3/4% PERFORMANCECHARACTERISTICS
35 (132)
42 (159)
50 (189)
2.JET-X 2% and JET-X 2 3/4% concentrates are not to be mixed for normal system operation.
JET-X-2A
BENEFITS
D
Transition
(Round)
A, B
Generator Foam
Solution
Inlet Pressure Output
Flow
psi
(bar)
cfm
(cmm)
gpm
(Lpm)
Expansion
___________ _____________
____________
_________
FEATURES
n FMApproved Models
WALL
NOTES:
Model No.
________
Data/Specifications
Description
The ANSUL actuated dampers and louvers are powered by 110 VAC
and are fail-safe open devices. Energized, the damper or louver is
closed with loss of power to open. They are available with either NEMA
4 or NEMA 7 actuators.
ROOF
JET-X HIGH-EXPANSIONFOAMGENERATORS
001273
96 in.
(2438 mm)
Application
26 in.
(660 mm)
Depending on the type of hazard and its configuration, a JET-X HighExpansion Foam System may be designed for total flooding or local
application. Common applications suited for high-expansion foam
include:
n Aircraft Hangars
54 in.
(1372 mm)
60 in.
(1524 mm)
1.5 IN.
(38 mm)
008446
006372b
ORDERINGINFORMATION DIMENSIONS
Clearance Dimensions*
Shipping
Part No.
A
B
C
D
E
Weights**
NEMA
4 / 7
Model
in. (mm) _________ _________
in. (mm) in. (mm) _________
in. (mm) _________
in. (mm) lb
(kg)
____________
_____
_________
________
430060/430061 Wall Intake Damper Assembly JET-X-5A
44.0 (1118) 44.0 (1118) 24.0 (610) 42.0 (1060) 51.8 (1314) 241 (109)
430062/430063 Roof Intake Damper Assembly JET-X-5A
46.0 (1168) 46.0 (1168) 16.0 (406) 42.0 (1067) 57.8 (1467) 285 (129)
430064/430065 Wall Relief Louver Assembly JET-X-5A
30.0 (762) 48.0 (1219) 6.0 (152)
50 (23)
430066/430067 Wall Intake Damper Assembly JET-X-15/20/27 54.0 (1372) 54.0 (1372) 24.0 (610) 53.0 (1340) 57.9 (1470) 315 (143)
430068/430069 Roof Intake Damper Assembly JET-X-15/20
54.0 (1372) 54.0 (1372) 16.0 (406) 53.0 (1346) 65.8 (1670) 360 (164)
430070/430071 Wall Relief Louver Assembly JET-X-15/20/27 60.0 (1524) 84.0 (2134) 6.0 (152)
140 (64)
437018/437097 Roof Intake Damper Assembly JET-X-27
54.0 (1372) 54.0 (1372) 14.0 (356) 53.0 (1346) 62.5 (1588) 525 (238)
* Actual dimensions of equipment will be approximately 0.25 in. (6.4 mm) smaller than clearance dimensions listed. TABLE 5
** Weights listed are for NEMA 4 models; add 20 lb (9.1 kg) for NEMA 7 models.
NOTE: The converted metric values in this document are provided for dimensional reference only and do not reflect an actual measurement.
+1-715-735-7411
www.ansul.com
n Power Stations
n Cable Tunnels
Foam Screen
Water
Motor
n Transformer Rooms
Blower Fan
Air
Flow
Foam
Foam
Solution
Inlet
Foam Solution
Spray
001274