Professional Documents
Culture Documents
BDM
- CAR -
FG Technology
1/43
EOBD2
Indice Index
Premessa / Premise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Il modulo EOBD2 / The EOBD2 module . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin dellinterfaccia EOBD2 / Pin of the EOBD2 interface . . . . . . . . . . . . . . 5
Pin Out BDM Motorola . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Pin Out BDM Motorola 2nd type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Pin Out Bdm Bosch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Adattatore da CMD/Dimensione Sport/Alien a FG Technology . . . . . . . . . . 9
Adattatore da EVC a FG Technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Ecu Bosch EDC16 e ME9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Ecu Bosch MED961 Ferrari Maserati . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Ecu Delphi . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Ecu Marelli . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ecu Siemens SID803 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Ecu Siemens SID803 A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Ecu Siemens SID201 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Ecu Siemens SID202 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Ecu Siemens SID203 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Ecu Siemens SID204 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Ecu Siemens SID206 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Ecu Siemens SID301 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Ecu Siemens MS45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Ecu Siemens MS S60/65 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Ecu Siemens HMC Theta PI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Ecu Siemens SIM 266 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Ecu Siemens Simos6.x . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Ecu Siemens MSV70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Ecu Siemens MSS70 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Ecu Siemens PPD1.1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Ecu Bosch ME9.7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Ecu Delphi DCM3.2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Ecu Delphi DCM3.x (MB Version) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Ecu Delphi DCM 3.5 PSA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Versione del manuale / Manual version . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
FG Technology
2/43
EOBD2
Premessa Premise
IMPORTANTE IMPORTANT
The connection between the EOBD interface and the ECU is very simple, but we
recommend to follow this manual attentively because each small error could damage the
ECU.
FG Technology
3/43
EOBD2
EOBD 2
Attenzione:
E indispensabile che linterfaccia sia
sempre
alimentata
utilizzando
un
alimentatore a 12V, indifferentemente dal
tipo di centralina che si deve leggere.
Attention:
Its essential that the interface has fed using
a feeder to 12V always, without note of from
the type of ECU that must be read.
FG Technology
4/43
EOBD2
FG Technology
5/43
EOBD2
Nella maggior parte delle centraline non segnato il Pin 1 usato come riferimento per il
corretto verso del Bdm; nella figura seguente possibile vedere lo schema della porta
Bdm con i valori di ogni suo Pin.
In best part of the ECU has not marked the Pin 1 used like reference for the correct toward
of the Bdm; in the following figure is possible see the scheme of the Bdm door with the
values of each his Pin.
FG Technology
6/43
EOBD2
FG Technology
7/43
EOBD2
FG Technology
8/43
EOBD2
Attenzione - Attention:
Lalimentazione deve essere data tramite il cavo con linterruttore SOLO alle ECU BOSCH.
The feeding must be date trouth the interrupt cable ONLY at the ECU BOSCH.
Adattatore dalla pressa di EVC a FG Technology - Adapter from EVC press to FG Tech
9/43
EOBD2
10/43
EOBD2
Importante:
Le centraline Bosch si alimentano tramite ladattatore Bosch come nei 3 passi seguenti:
Important:
The Bosch ECUs feed through the Bosch adapter like in the 3 following steps:
PASSO 1 STEP 1
PASSO 2 STEP 2
PASSO 3 STEP 3
FG Technology
11/43
EOBD2
FG Technology
12/43
EOBD2
Importante:
Le centraline Bosch si alimentano tramite ladattatore Bosch come nei 3 passi seguenti:
Important:
The Bosch ECUs feed through the Bosch adapter like in the 3 following steps:
PASSO 1 STEP 1
PASSO 2 STEP 2
PASSO 3 STEP 3
FG Technology
13/43
EOBD2
ECU Delphi
Figura 9: la spina originale della ECU Delphi Original connector of Delphi ECUs
FG Technology
EOBD2
ECU Marelli
Figura 12: Pinout della centralina Marelli Pinout of the Marelli ECUs
15/43
EOBD2
Successivamente,
collegare
la
centralina all interfaccia EOBD2
inserendo il cavo flat usando
ladattatore Marelli.
- Vedere figura 13 Figura 15b: pinstrip saldati sul BDM/pinstrip join on Bdm
16/43
EOBD2
Figura: 16: Spina principale della Ecu Siemens SID 803 Original connector of Siemens SID803
17/43
EOBD2
Figura 19: la SID 803A ha lo stesso Pinout della SID 803 SID803A has the same Pinout of SID803
FG Technology
18/43
EOBD2
Figura 22: Spina pricipale Ecu Siemens SID201 Original connector of ECU Siemens SID201
- Vedere figura 23 - See figure 23 Fatto ci, inserire ladattatore Siemens con
il cavo flat nei pin strip saldati sulla porta
BDM.
Fact that, insert the Siemens adapter with the
cable flat in the pinstrip joined on the BDM
door.
- Vedere figura 24
- See figure 24 FG Technology
19/43
EOBD2
Figura 25: Il Pinout uguale della centralina Siemens SID803 The pinout is the same of SID803
- Vedere figura 26 a lato - See figure 26 to sideFatto ci, inserire ladattatore Siemens con il
cavo flat nei pin strip saldati.
Fact that, insert the Siemens adapter with the
cable flat in the pinstrip previously joined.
- Figura 27 - Figure 27 -
FG Technology
20/43
EOBD2
Figura 28: La spina principale dell Ecu Siemens SID203, il pinout uguale alle SID201.
Main connector of ECU Siemens SID203, the pinout is the same of SID201.
IMPORTANTE:
Fare ponte tra le due piazzole mostrate
in
figura
30. Senza
questo
collegamento il BDM non potr
funzionare.
IMPORTANT:
Close the jumper shows in figure 30.
Without this connection the BDM will
cannot work.
Infine, utilizzare ladattatore Siemens
con il cavo flat nei pin strip.
Finaly, insert the Siemens adapter
with the cable flat in the pin strip.
FG Technology
21/43
EOBD2
Figura 31: La spina pricipale Ecu Siemens SID204 uguale a quella della SID201
The main conncector of Siemens SID 204 ECU is equal to that of the SID201.
FG Technology
22/43
EOBD2
Figura 34: spina principale della centralina Siemens SID206. principal taking of the Siemens SID206 ECU.
IMPORTANTE:
Fare ponte tra le due piazzole mostrate in
figura 36. Senza questo collegamento il
BDM non potr funzionare.
Do bridge between the two circles you show in
figure 36. Without this connection the BDM
don't work.
FG Technology
23/43
EOBD2
Figura 38: spina principale della centralina Siemens SID301 / Principal taking of the Siemens SID301 ECU.
FG Technology
24/43
EOBD2
Figura 41: spina principale centralina Siemens MS45 original connector of Siemens MS45 ECU
FG Technology
25/43
EOBD2
Figura 44: spina principale centralina Siemens MS S65 Main connector of Siemens MS S60/65 ECU
Successivamente,
inserire
ladattatore
Siemens con il cavo flat rispettando il corretto
verso e il PIN 1 indicato nellimmagine.
Figura 46
Figure 45-46: ECU Siemens MSS65 e le sue due porte BDM / ECU Siemens MSS65 and his two BDM doors
FG Technology
26/43
EOBD2
Figura 47: Spina principale HMC Theta PI Main connector of ECU HMC Theta PI
Inserire poi ladattatore Siemens con il cavo flat. Rispettare, come sempre, il PIN 1
mostrato nella figura 48 per inserire il cavo flat nel verso corretto.
Accordingly, insert the Siemens adapter with the flat cable. Respect, like always, the PIN 1
shown in the figure 48 for insert the flat cable in the correct verse.
FG Technology
27/43
EOBD2
Figura 49: Spina principale dell ECU SIM266 Main connector of SIM266 ECU
FG Technology
2 SRESET#
4 DSCK
6 VFLS1
8 DSDI
10 DSDO
28/43
EOBD2
Occorre crearsi ora un adattatore con una vaschetta a 10 Pin standard per poter
collegare la centralina allinterfaccia - Vedere figura 51 Now, you need to create an adapter with 10 Pin standard for connect the ECU to the
interface - See figure 51 -
Figura 51: Pinout del cavo per il BDM in ECU SIM266 / Pinout cable for the BDM in ECU SIM266
Figura 53:
adattatore creato per leggere Bdm
Adapter created for read Bdm
FG Technology
29/43
EOBD2
FG Technology
30/43
EOBD2
Figura 55: Spina principale dell ECU Siemens SIMO-6.x Main connector of Siemens SIMO-6.x
FG Technology
2 SRESET#
4 DSCK
6 VFLS1
8 DSDI
10 DSDO
31/43
EOBD2
Occorre crearsi ora un adattatore con una vaschetta a 10 Pin standard per poter
collegare la centralina allinterfaccia - Vedere figura 57 Now, you need to create an adapter with 10 Pin standard for connect the ECU to the
interface - See figure 57 -
Figura 58: Pinout del cavo per il BDM in ECU SIM266 / Pinout cable for the BDM in ECU SIM266
Figura 60:
adattatore creato per leggere Bdm
Adapter created for read Bdm
FG Technology
32/43
EOBD2
FG Technology
33/43
EOBD2
Figura 62: spina principale ECU MSV70 main connector of ECU MSV70
Figura 63: pin strip sul Bdm/ pin strip join on Bdm
FG Technology
34/43
EOBD2
Figura 66: Pinout della spina principale MSS70 / The pinout of the thorn principal ECU MSS70
FG Technology
35/43
EOBD2
Figura 70: Spina principale ECU Siemens PPD1.1 main connector Siemens PPD1.1 ECU
36/43
EOBD2
Figura 73: Spina principale ECU Bosch ME9.7 main connector of Bosch ME9.7 ECU
A questo punto, inserire ladattatore Siemens con il cavo flat, rispettando sempre il PIN 1
indicato nella figura 74.
To this point, insert the Siemens adapter with the flat cable, always respecting the PIN 1 suitable
in the figure 74.
FG Technology
37/43
EOBD2
Figura 75: Spina principale Delphi DCM3.2 main connector of Delphi DCM3.2
FG Technology
38/43
EOBD2
Figura 79: Spina principale Delphi DCM3.x (VersioneMB) main connector of Delphi DCM3.x (MB Version)
Figura 80: pin strip saldati sul Bdm e ponte tra i 2 pin
Pinstrip join on the Bdm and bridge between the 2 pin
FG Technology
39/43
EOBD2
Figura 83: Spina principale dell ECU DCM 3.5 Main connector Delphi DCM3.5
Le centaline Siemens SIM266 devono essere alimentate tramite la spina originale. Figura 83
The Siemens ECU SIM266 must be feeds through the original connector. Figure 83
Su questo tipo di ECU i segnali del BDM sono disposti come nella figura successiva:
On this type of ECU the BDM has arranged like in the follow figure:
FG Technology
40/43
EOBD2
1 VFLS0
3 GND
5 GND
7 HRESET#
9 VDD SENSE
2 SRESET#
4 DSCK
6 VFLS1
8 DSDI
10 DSDO
Occorre crearsi ora un adattatore con una vaschetta a 10 Pin standard per poter
collegare la centralina allinterfaccia - Vedere figura 46 Now, you need to create an adapter with 10 Pin standard for connect the ECU to the
interface - See figure 46
Figura 46: Pinout del cavo per il BDM in ECU SIM266 / Pinout cable for the BDM in ECU SIM266
FG Technology
41/43
EOBD2
FG Technology
42/43
EOBD2
FG Technology
Gennaio 2011
January 2011
43/43
EOBD2