Professional Documents
Culture Documents
2 18W Hi-Fi Stereo Power Amplifier based around two TDA2030 ICs. It has good input sensitivity,
low distortion, good operating stability and full protection against overloads and output short-circuits. It
can be used as a booster amplifier for existing small systems or to drive a second pair of speakers besides
the ones already connected to the system. The board needs a symmetrical power supply of 18Vdc/3A
and can be connected to loads of 8 or 4 Ohm. Large heat sink is required for this circuit. Diagram shown
below indicates only left channel. Make two circuits for for stereo version.
Circuit Diagram
Diagram Shows Only One
Channel
Parts
R1 = 22K
R2 = 680R
R3 = 22K
R4 = 1R-1w
D1 = 1N4001
D2 = 1N4001
C1 = 1uf-25V
C2 = 22uF-25V
C3 = 100nF-63V
C4 = 100nF-63V
C5 = 100uF-25V
C6 = 100uF-25V
C7 = 220nF-63V
IC = TDA2030
If it does not work:
Check your work for possible dry joints, bridges across adjacent tracks or soldering flux residues that
usually cause problems.
Check again all the external connections to and from the circuit to see if there is a mistake there.
See that there are no components missing or inserted in the wrong places.
Make sure that all the polarized components have been soldered the right way round.
Make sure the supply has the correct voltage and is connected the right way round to your circuit.
Check your project for faulty or damaged components.
Technical Specifications:
Supply voltage = 18Vdc/3A symmetrical (see text)
Current consumption = 3A maximum
Input impedance = 500K Ohms
Input sensitivity = 250 mV
Signal to noise ratio = 80 dB
Frequency response = 20 20,000 Hz 1 dB
Distortion = 0.5 % maximum
Load impedance = 4 8 ohm
https://www.eeweb.com/blog/extreme_circuits/18w-18w-stereo-hi-fi-audio-amplifier-tda2030
http://www.electroschematics.com/7875/tda2030-audio-amplifier-circuits/
Buat rekan-rekan yang baru belajar elektronika dan ingin mencoba merakit rangkaian speaker aktif yang
ada di pasaran berikut ini gambar layoutnya. rangkaian ini memiliki tingkat keberhasilan yang sangat
tinggi. menggunakan komponen yang banyak tersedia di pasaran, dilengkapi dengan pengatur volume,
bass, dan treble (tone control). Rangkaian power supply (catu daya) dibuat menjadi satu PCB dengan
rangkaian amplifier dan tone controlnya. Komponen yang berada di luar PCB, hanya Loudspeaker dan
Transformator. kecuali jika rekan2 ingin menempatkan potensiometer di luar PCB (misalnya pada box).
Power Supply
https://heriyawan.wordpress.com/2011/03/02/speaker-aktif-tda2030/
kalau menggunakan PCB di atas buat saja 2 PCB, semua komponen x 2, kecuali komponen catu daya
(D1-D4 dan C1,C2), gunakan potensiometer stereo (harus menggunakan kabel untuk menghubungkan
potensiometer ke PCB)
Berikut daftar komponen yang diperlukan:
1. IC TDA2030 1 bh
2. Potensiometer B50k 3 bh
3. R 4,7 K 3 bh
4. R 47 ohm 1 bh
5. R 1 k 1 bh
6. R 390 ohm 1 bh
7. R 18 k 1 bh
8. R 20 k 1 bh
9. C 470n 3 bh
10. C 47n 1 bh
11. C 1n 1 bh
12. C 22n 1 bh
13. Elko 10 uF/16V 1 bh
14. Elko 22 uF/16V 1 bh