Professional Documents
Culture Documents
Fajar Benua Indopack was established in 1984 as a trading company, selling sealing and
insulation products. Today, we have expanded our line of business with advanced engineering
products such as Expansion Joints, Strainer, Mechanical Seals, Fluoroplastic Lining, and advanced
application Hoses. In addition to that, we are also dedicated to provide Engineering Services such
as Stress Analysis, Installation, Construction, Troubleshooting, and Emergency Breakdown Repair
for our clients.
We strive in our after sales service, providing customers with technical guidance and
documentation. Our teams are highly dedicated to increase and utilize excellent service through
the network of 16 Branches and Project Division, located all over the nation with self-motivated,
dynamic, and trained sales and engineering staffs. More than two decades of experience through
intensive development and work improvement have enabled us to optimize our engineering
services.
The company works on the principle of continueous upgrade of quality service and products, by
providing customer feedbacks and suggestions to our principals and implementing them within a
time frame that keeps the company and our products always one step ahead in the market.
PT. Fajar Benua Indopack is committed not only to become a highly responsible service provider,
but also a major profit contributor for your business and the nations growth.
Service Temperature
Max. 580 C
Pressure Range
Standard Size
*Maximum temperature & pressure combinations cannot be used at the same time.
Basic type
These gaskets are suitable at joints for pipe flanges, heat exchangers, towers & tanks, valve bonnets and other equipments
that handle high temperature & high pressure fluids used in various industries such as oil refinery, chemical, power, gas and
shipbuilding.
Up to 530 C
o
Up to 1300 C (with NA Ceramic Filler)
2
Up to 60 kgf/cm
Standard Thickness
3.0 0r 1/8
R (Radius)
8 min
W (Width)
7 min
Metal Thickness
0.3 0.5
Metal jacketed gasket suitable for use in the Heat Exchanger, Pressure Vessel, Valve Bonnet, Autoclave, Pipe Flange, etc.
Standard Size
Material
They are mainly used in the high pressure vessel, pipe flanges, valve bonnets handling high pressure steam, gas, hot oil,
oil gas, solvent vapor industries, etc
Isolation Gasket
GPT Specialty Isolation Products provide custom sealing solutions for flanges to meet unique applications and demands.
Pikotek Insulating Gasket Type
1.
2.
3.
4.
5.
Orifice Plate
Steel Washer
Isolating Washer
Seal Material
Seal Material
Isolating Sleeve
Isolating Washer
Steel Washer
Seal Element
Temperature Range
EPDM
(-54 to 149 deg C)
Nitrile
(-54 to 149 deg C)
Neoprene (-40 to 79 deg C)
Viton
(-29 to 177 deg C)
PTFE
(Cyrogenic to 232 deg C)
Isolating Sleeve
Application
350 C to 430 C
220 C to 320 C
30 to 60 kg/cm
Applied Fluid : Water, Alkali, Salt Solution, Hot Oil, Oil Gas, Freon Gas Below,
Organic Solvent, etc
Thickness (mm)
0.5 6.0
1270x1270/1270x2540
Sheet (mm)
1270x3810/1520x1520
2540x3810/1520x3040
Leakblok Gasket
Innovative technology, LEAKBLOK is specially created with environmentally friendly solvent free process.
Colour
Binder
NBR
Service Temp.
Service Pressure
pH
4 11
Above is general range and has no guarantee for
every case.
Hot oil, Oil gas, Water, Alkali, Other gas type fluids,
Salt solution & Organic solvent, Saturated Steam
Applied Fluids
Thickness (mm)
Leak Bloks unique features such as superior seal ability, strong durability and excellent flexibility are technologically
more advanced than conventional products
Application
Graphite
pH Range : 4-11
Press: 20 kg-f/cm
(garlock/Chesterton)
Press: 20 kg-f/cm
PTFE
Temp: Max.150 C
Temp: Max.315 C
Rubber
(Neoprene/EPDM/NBR)
Temp: Max.120 C
Metal Expansion Joints or Bellows are used to accommodate the movement of pressurized piping system caused by thermal
growth, contraction and small vibrations. They are mainly used in the jointing pipe of boiler, turbine, transfer pump,
pipelines a handling high pressure steam, gas, hot oil, oil gas, etc.
Strainer
For special, unique/application, Hidroflex can fabricate any custom made strainers according to the specific requirement
of the customers.
Design and manufactured by PT. Hidroflex Indonesia, Cibinong.
Material
Strainer Type
T-STRAINER
DUPLEX STRAINER
Y-STRAINER
BASKET STRAINER
CONICAL STRAINER
AUTOMATIC STRAINER
c.
Belt Type
Flange Type
Bellows type
Used in ducting utility system for a max. pressure up to 0.35 Bar, low or high temperature (up to 1000 deg C). Our Fabric
Expansion Joint have been applied in the loop of many other major industries such as Pulp and Paper Plants, Power Plants,
Refineries (Oil & Gas), Cement Plants, Food Processing, Steel Mills, and many other industries.
DN20 to DN3600
Pressure
Max. 30 Bar
Elastomer Grades
Reinforcing Material
Rubber Expansion Joints are used to provide relief from stress caused by thermal movement and mechanical activity in
piping and ducting system. The other main job is to reduce noise, isolate vibration, compensate for misalignment and
prolong the life of motive equipment. They also provide excellent resistance to shock and wear.
Universal type
Elbow Connector
Rectangular Type
Teflon Lined
Gland Packing
Gland packing or mechanical packing is the sealing material for use in rotating and static equipment.
Yarn Material
Wire Reinforce
Construction of
braiding
Range
Temperature
Range Pressure
Size
20 to 150 kg.f/cm
1/8 to 5
Gland packing suitable for use in general pump, valve, reciprocating pump, cylinder hydraulic, manholes gasket, etc
Mechanical Seal
Our originally designed and continuously developed Mechanical Seals have the ability of providing customized seals
solution as per your process requirement.
Designed and manufactured by PT. Tri Graha Sealisindo, Cibinong.
ROTARY SEAL
Single Spring Rubber Bellows, Single Coil Spring,
Multi Spring, Wave Spring, Metal Bellows Seal,
Cartridge.
Carbon, Silicone Carbide, Tungsten Carbide,
Stainless Steel, Chrome oxide
Available Type
Face Material
Metal Components
Packing/Secondary
seal
STATIONARY (SEAT)
Material of Stationary
Available Type
Material of Seat
Packing
OPERATING LIMITS
Shaft size
Pressure
Temp
Speed
25 100 mm (1 4)
0 2.5 Mpa (0-360 PSI)
o
o
-20 200 C (-22 390 F)
25 m/sec
Flexible hose
Available in metal, fluoropolymer, composite hose and others.
Application
Metal Hose
Fluoropolymer
Composite
Material
Size
1/4 12
3/16 3
1 12
Range Pressure
Range
Temperature
Cryogenic to 1500 F
-45 F 450 F
-328 F to +325 F
Applied Fluid
Fluoroplastic Lining
Fluorocarbon resin corrosion resistance product. Designed and manufacturedby PT. Jeil Fajar Indonesia, Cibinong.
PROPERTIES
a. Service temperature
b. Melting Point
c. Chemical Inertness
: 29C-260C
: 327C
: resist to most all chemicals
APPLICATION
1. Piping system:
a. PTFE lined pipe fitting
(tee, cross tee, elbow, reducer, spacer, etc)
b. PTFE/ PFA lined valves
c. PTFE lined spool pipe, etc
2. Fluoroplastic Lining:
a. Storage Tank
b. Hopper
c. Mixer tank/ agitator
d. Header, etc.
THERMAL JACKETING
Thermal Jacketing from FBI will provide uniform heat transfer, easy
installation and removal, lower operating cost and a professional
appearance.
FASTENING SYSTEM
302-A, Nitco Biz Park, Plot No. C-19, Road No. 16, Wagle
Estate, Thane, India