You are on page 1of 32

PANEL ANTENNAS

WITH TWO LOW BAND ARRAYS

22 | April 2015

TwinLine

Quad antennas with two


multiband arrays housed
in an optimally designed
package for low windload.
Ideal for site/technology
sharing.

April 2015 | 23

(2x) 698-960 / 1695-2690 / 1695-2690 MHz


5980300
5980300A

5980300G

5980300DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 18.0 / 18.0 dBi | Variable Tilt

Twin tri band antenna, dual polarisation, 12 connectors


Independent tilt on each band 0-10 / 0-12 / 0-12
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5980300

Remote Electrical Tilt AISG1.1

5980300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5980300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator

5980300DG

Access Ports Description (Connectors)


This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.

R1

R2

Y1

Y3

Ultra Wide Band Bottom System

1695-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

Y2

Y4

Ultra Wide Band Top System

1695-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

Ultra Low Band

698-960 MHz Ports

Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)

Tilt 0
Tilt Mid Value
Tilt Max Value

R1-R2

(4x) 7/16-DIN Female Long Neck

Y1-Y3 (Bottom)

Y2-Y4 (Top)

700

800

900

1800

2100

2600

1800

2100

2600

15.5
15.5
15.2

16.5
16.4
16.2

17.4
17.3
17.0

17.1
17.1
17.1

17.5
17.5
17.4

18.0
18.0
17.8

17.1
17.1
17.1

17.5
17.5
17.4

18.0
18.0
17.8

Input Impedance

50

50

50

VSWR

< 1.5

< 1.5

< 1.5

Polarisation

45

Horizontal Beamwidth (-3 dB)

75

Vertical Beamwidth (-3 dB)

8.6

45

68

65

65

7.5

6.7

7.0

45

63

61

65

6.4

5.2

6.5

63

61

5.9

4.7

Electrical Downtilt Range

0-10

0-12

0-12

Inter/Intra Band Isolation

> 30 dB, > 28 dB from 0 to 2 tilt

> 30 dB, > 28 dB from 0 to 2 tilt

> 30 dB, > 28 dB from 0 to 2 tilt

18 dB Typical

18 dB Typical

18 dB Typical

> 30 dB
> 25 dB

> 30 dB
> 25 dB

> 30 dB
> 25 dB

Maximum Power (Per Port)

250 W

200 W

200 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

< -110 dBm

Upper Sidelobe Rejection


(20 sector above main beam)
Front-to-Back
Ratio

@ 180
@ 180 30

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
(MCDU)
RET-Ready
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt
(RET) in Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas
with factory embedded motors (for antenna sharing or two technologies). Refer to ordering
options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

24 | April 2015

(2x) 698-960 / 1695-2690 / 1695-2690 MHz


5980300
5980300A

5980300G

5980300DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 18.0 / 18.0 dBi | Variable Tilt
Environmental

Packaging

Operating Temperature Range

-40 C to +60 C

Environmental

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
59 kg
Includes 0900181/00 Kit

ETS 300 019

RoHS Compliant

Yes

Mechanical Characteristics
Dimensions (Height x Width x Depth)

2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

48 kg

Shroud

Outdoor Fibreglass, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h

Frontal: 990 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 555 N

Rear: 920 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

698-960 MHz

YELLOW

1695-2690 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 25

(2x) 790-960 / 1710-2170 / 2500-2690 MHz


5982200
5982200A

5982200G

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Twin tri band antenna, dual polarisation, 12 connectors
Independent tilt on each band 0-10 / 0-12 / 0-12

LTE 800 Ready


LTE 2600 Ready

MET and RET versions, AISG1.1 or 3GPP/AISG2.0


Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options

Model Number

Manual Electrical Tilt

5982200

Remote Electrical Tilt AISG1.1

5982200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5982200G

Access Ports Description (Connectors)


This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings

Low Band

790-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

YELLOW Rings

High Band (Top Array)

2500-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

BLUE Rings

High Band (Bottom Array)

1710-2170 MHz Ports

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)

Tilt 0
Tilt Mid Value
Tilt Max Value

Low Band (RED or GREEN)

High Band (BLUE)

High Band (YELLOW)

790...880...960

1710...1880

1900...2170

2500...2690

16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4

16.5...16.9
16.4...16.7
16.3...16.5

16.9...17.3
16.7...17.2
16.5...17.0

17.4...17.8
17.3...17.7
17.2...17.5

Input Impedance

50

50

50

VSWR

< 1.5

< 1.5

< 1.5

Polarisation

45

45

Horizontal Beamwidth (-3 dB)

75...68...63

65

45
62

60

Vertical Beamwidth (-3 dB)

Electrical Downtilt Range

0-10

0-12

0-12

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

45 dB Typical

45 dB Typical

45 dB Typical

> 30 dB

> 30 dB

> 30 dB

18 dB Typical

18 dB Typical

18 dB Typical

Intra Band Isolation


Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back Ratio

> 30 dB

> 30 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET Module Part Number


(one per antenna)

MDCU-A0000

for AISG1.1 protocol (one unit included in 5982200A)

MDCU-G0000

for 3GPP/AISG2.0 protocol (one unit included in 5982200G)

Environmental
Operating Temperature Range
Environmental
RoHS

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

26 | April 2015

(2x) 790-960 / 1710-2170 / 2500-2690 MHz


5982200
5982200A

5982200G

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Packaging

Mechanical Characteristics
Dimensions (Height x Width x Depth)

2700 x 442 x 152 mm (219 mm with Rear Connectors)

Weight (Excluding Mounting Accessories)

56 kg

Shroud

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 70 kg

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 160 km/h

Frontal: 1300 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 220 N

Rear: 1700 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

Not available

---

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

790-960 MHz

GREEN

790-960 MHz

BLUE

1710-2170 MHz

YELLOW

2500-2690 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 27

(2x) 790-960 / 1710-2170 / 2500-2690 MHz


5982200 lv
5982200A lv

(lightweight version)

5982200G lv

5982200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.3 / 17.6 dBi | Variable Tilt

Twin tri band antenna, dual polarisation, 12 connectors


Independent tilt on each band 0-10 / 0-12 / 0-12
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5982200 lv

Remote Electrical Tilt AISG1.1

5982200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5982200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)

5982200DG lv

Access Ports Description (Connectors)


This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings

Low Band

790-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

YELLOW Rings

High Band (Top Array)

2500-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

BLUE Rings

High Band (Bottom Array)

1710-2170 MHz Ports

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics

Low Band (RED or GREEN)

Frequency Bands (MHz)


Gain (dBi)

Tilt 0
Tilt Mid Value
Tilt Max Value

High Band (BLUE)

High Band (YELLOW)

790...880...960

1710...1880

1900...2170

2500...2690

16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4

16.5...16.9
16.4...16.7
16.3...16.5

16.9...17.3
16.7...17.2
16.5...17.0

17.2...17.6
17.1...17.5
17.0...17.3

Input Impedance

50

50

50

VSWR

< 1.5

< 1.5

< 1.5

Polarisation

45

Horizontal Beamwidth (-3 dB)

75...68...63

45
65

45
62

60

Vertical Beamwidth (-3 dB)

Electrical Downtilt Range

0-10

0-12

0-12

> 28 dB
> 27 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

Intra Band Isolation


Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back Ratio

45 dB Typical

45 dB Typical

45 dB Typical

> 28 dB (900 Band)


> 27 dB (800 Band)

> 30 dB

> 30 dB

18 dB Typical

18 dB Typical

18 dB Typical

> 25 dB

> 25 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

28 | April 2015

(2x) 790-960 / 1710-2170 / 2500-2690 MHz


5982200 lv
5982200A lv

(lightweight version)

5982200G lv

5982200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.3 / 17.6 dBi | Variable Tilt
Environmental

Packaging

Operating Temperature Range

-40 C to +60 C

Environmental

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
59 kg
Includes 0900181/00 Kit

ETS 300 019

RoHS Compliant

Yes

Mechanical Characteristics
Dimensions (Height x Width x Depth)

2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

48 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr


at 150 km/h

Wind Load
(EN1991-4-1)

at 160 km/h

Mounting Kit Options

Survival: 200 km/h

Frontal: 990 N

Lateral: 555 N

Rear: 920 N

Highest value: 1450 N at 110

Frontal: 1130 N

Lateral: 630 N

Rear: 1045 N

Highest value: 1650 N at 110

Part Number

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

790-960 MHz

GREEN

790-960 MHz

BLUE

1710-2170 MHz

YELLOW

2500-2690 MHz

2683

432

RED

153

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

1865

Location of the MDCU


for RET Control

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 29

(2x) 790-960 / 1710-2170 / 1710-2170 MHz


5980200
5980200A

5980200G

5980200DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Twin tri band antenna, dual polarisation, 12 connectors
Independent tilt on each band 0-10 / 0-12 / 0-12

LTE 800 Ready

MET and RET versions, AISG1.1 or 3GPP/AISG2.0


Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options

Model Number

Manual Electrical Tilt

5980200

Remote Electrical Tilt AISG1.1

5980200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5980200G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)

5980200DG

Access Ports Description (Connectors)


This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings
WHITE Rings
BLUE Rings

Low Band

790-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

High Band (Top Array)

1710-2170 MHz Ports


(Wide Band)

(4x) 7/16-DIN Female Long Neck

High Band (Bottom Array)

1710-2170 MHz Ports


(Wide Band Optimised for UMTS)

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics

Low Band (RED or GREEN)

Frequency Bands (MHz)

790...880

880...960

1710...1880

1900...2170

1710...1880

1900...2170

17.2

17.5

16.5...16.7
16.3...16.5
16.0...16.3

16.7...17.2
16.5...17.0
16.3...16.5

16.5...16.9
16.4...16.7
16.3...16.5

16.9...17.3
16.7...17.2
16.5...17.0

Gain (dBi)

Tilt 0
Tilt Mid Value
Tilt Max Value

High Band (WHITE)

High Band (BLUE)

Input Impedance

50

50

50

VSWR

< 1.5

< 1.4

< 1.4

Polarisation
Horizontal Beamwidth (-3 dB)

45
75

45
68

65

65

62

Vertical Beamwidth (-3 dB)

Electrical Downtilt Range

0-10

0-12

0-12

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

45 dB Typical

45 dB Typical

45 dB Typical

> 29 dB

> 30 dB

> 30 dB

18 dB Typical

18 dB Typical

18 dB Typical

Intra Band Isolation


Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back Ratio

45
62

> 30 dB

> 30 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

30 | April 2015

(2x) 790-960 / 1710-2170 / 1710-2170 MHz


5980200
5980200A

5980200G

5980200DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Environmental

Packaging

Operating Temperature Range

-40 C to +60 C

Environmental

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 70 kg

ETS 300 019

RoHS Compliant

Yes

Mechanical Characteristics
Dimensions (Height x Width x Depth)

2700 x 442 x 152 mm (219 mm with Rear Connectors)

Weight (Excluding Mounting Accessories)

56 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 160 km/h (EN1991-4-1)

Frontal: 1512 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 512 N

Rear: 1418 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

790-960 MHz

GREEN

790-960 MHz

WHITE

1710-2170 MHz

BLUE

1710-2170 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 31

(2x) 790-960 / 1710-2170 / 1710-2170 MHz


5980200 lv
5980200A lv

(lightweight version)

5980200G lv

5980200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.2 / 17.3 dBi | Variable Tilt

Twin tri band antenna, dual polarisation, 12 connectors


Independent tilt on each band 0-10 / 0-12 / 0-12
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5980200 lv

Remote Electrical Tilt AISG1.1

5980200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5980200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)

5980200DG lv

Access Ports Description (Connectors)


This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.
RED and GREEN Rings

Low Band

790-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

WHITE Rings

High Band (Top Array)

1710-2170 MHz Ports


(Wide Band)

(4x) 7/16-DIN Female Long Neck

BLUE Rings

High Band (Bottom Array)

1710-2170 MHz Ports


(Wide Band Optimised for UMTS)

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics

Low Band (RED or GREEN)

Frequency Bands (MHz)

790...880

880...960

1710...1880

1900...2170

1710...1880

1900...2170

17.2

17.5

16.5...16.7
16.3...16.5
16.0...16.3

16.7...17.2
16.5...17.0
16.3...16.5

16.5...16.9
16.4...16.7
16.3...16.5

16.9...17.3
16.7...17.2
16.5...17.0

Gain (dBi)

Tilt 0
Tilt Mid Value
Tilt Max Value

High Band (WHITE)

High Band (BLUE)

Input Impedance

50

50

50

VSWR

< 1.5

< 1.4

< 1.4

Polarisation
Horizontal Beamwidth (-3 dB)

45
75

45
68

45

65

62

65

62

Vertical Beamwidth (-3 dB)

Electrical Downtilt Range

0-10

0-12

0-12

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

45 dB Typical

45 dB Typical

45 dB Typical

> 29 dB

> 30 dB

> 30 dB

18 dB Typical

18 dB Typical

18 dB Typical

> 30 dB

> 30 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

< -110 dBm

Intra Band Isolation


Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back Ratio

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

32 | April 2015

(2x) 790-960 / 1710-2170 / 1710-2170 MHz


5980200 lv
5980200A lv

(lightweight version)

5980200G lv

5980200DG lv

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 17.5 / 17.2 / 17.3 dBi | Variable Tilt
Environmental

Packaging

Operating Temperature Range

-40 C to +60 C

Environmental

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
59 kg
Includes 0900181/00 Kit

ETS 300 019

RoHS Compliant

Yes

Mechanical Characteristics
Dimensions (Height x Width x Depth)

2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

48 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr


at 150 km/h

Wind Load
(EN1991-4-1)

at 160 km/h

Mounting Kit Options

Survival: 200 km/h

Frontal: 990 N

Lateral: 555 N

Rear: 920 N

Highest value: 1450 N at 110

Frontal: 1130 N

Lateral: 630 N

Rear: 1045 N

Highest value: 1650 N at 110

Part Number

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

GREEN

790-960 MHz

WHITE

1710-2170 MHz

BLUE

1710-2170 MHz

432

790-960 MHz

153

RED

1865

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

2683

Location of the MDCU or MDDU


for RET Control

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 33

(2x) 698-960 / 1695-2690 MHz


5961300
5961300A

5961300G

5961300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 17.5 / 18.5 dBi | Variable Tilt

Twin dual band antenna, dual polarisation, 8 connectors


Independent tilt on each band 0-10 / 0-10
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5961300

Remote Electrical Tilt AISG1.1

5961300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5961300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator

5961300DG

Access Ports Description (Connectors)


This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.

R1

R2

Ultra Low Band

698-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

Y1

Y2

Ultra Wide Band

1695-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)

Tilt 0
Tilt 5
Tilt 10

R1-R2

Y1-Y2

700

800

900

1800

2100

2600

15.5
15.5
15.2

16.5
16.4
16.2

17.4
17.3
17.0

17.7
17.7
17.7

18.1
18.1
18.0

18.5
18.5
18.2

Input Impedance

50

50

VSWR

< 1.5

< 1.5

Polarisation

45

45

Horizontal Beamwidth (-3 dB)

75

68

65

65

63

61

Vertical Beamwidth (-3 dB)

8.6

7.5

6.7

6.1

5.3

4.2

Electrical Downtilt Range

0-10

0-10

Inter/Intra Band Isolation

> 30 dB, > 28 dB from 0 to 2 tilt

> 30 dB, > 28 dB from 0 to 2 tilt

18 dB Typical

18 dB Typical

> 30 dB
> 25 dB

> 30 dB
> 25 dB

Maximum Power (Per Port)

250 W

200 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

Upper Sidelobe Rejection


(20 sector above main beam)
Front-to-Back
Ratio

@ 180
@ 180 30

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

34 | April 2015

(2x) 698-960 / 1695-2690 MHz


5961300
5961300A

5961300G

5961300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 17.5 / 18.5 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

44 kg

Shroud

Outdoor Fibreglass, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h

Frontal: 990 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 555 N

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
55 kg
Includes 0900181/00 Kit

Rear: 920 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

698-960 MHz

YELLOW

1695-2690 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 35

(2x) 790-960 / 1710-2170 MHz


5961200
5961200A

5961200G

5961200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 17.5 / 18.6 dBi | Variable Tilt
Twin dual band Antenna, dual polarisation, 8 connectors
Independent tilt on each band 0-10 / 0-10

LTE 800 Ready

MET and RET versions, AISG1.1 or 3GPP/AISG2.0


Single RET module to control all tilt angles, fully inserted inside the antenna (field replaceable)
Ordering Options

Model Number

Manual Electrical Tilt

5961200

Remote Electrical Tilt AISG1.1

5961200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5961200G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12)

5961200DG

Access Ports Description (Connectors)


This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
RED | GREEN Rings

Low Band

790-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

WHITE | BLUE Rings

High Band

1710-2170 MHz Ports (Wide Band)

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics

Low Band (RED or GREEN)

Frequency Bands (MHz)


Gain (dBi)

Tilt 0
Tilt 5
Tilt 10

High Band (WHITE or BLUE)

790...880...960 MHz

1710...1880

1900...2170

16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4

17.8...18.2
17.7...18.0
17.6...17.8

18.2...18.6
18.0...18.5
17.8...18.3

Input Impedance

50

50

VSWR

< 1.5

< 1.5

Polarisation

45

45

Horizontal Beamwidth (-3 dB)


Vertical Beamwidth (-3 dB)
Electrical Downtilt Range
Intra Band Isolation
Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back Ratio

75...68...63

65

62

7.0

5.5

5.0

0-10

0-10

> 28 dB

> 30 dB, > 28 dB from 0 to 2 tilt

45 dB Typical

45 dB Typical

> 25 dB for 790-880 MHz


> 28 dB for 880-960 MHz

> 30 dB

18 dB Typical

18 dB Typical

> 30 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

36 | April 2015

(2x) 790-960 / 1710-2170 MHz


5961200
5961200A

5961200G

5961200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 17.5 / 18.6 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

2700 x 442 x 152 mm

Weight (Excluding Mounting Accessories)

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 67 kg

52 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 160 km/h (EN1991-4-1)

Frontal: 1512 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 512 N

Rear: 1418 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

790-960 MHz

GREEN

790-960 MHz

BLUE

1710-2170 MHz

WHITE

1710-2170 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 37

(2x) 790-960 / 1710-2170 MHz


5961200 lv
5961200A lv

(lightweight version)

5961200G lv

5961200DG lv

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 17.5 / 18.6 dBi | Variable Tilt

Twin dual band antenna, dual polarisation, 8 connectors


Independent tilt on each band 0-10 / 0-10
Lightweight TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

LTE 800 Ready

Ordering Options

Model Number

Manual Electrical Tilt

5961200 lv

Remote Electrical Tilt AISG1.1

5961200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5961200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12)

5961200DG lv

Access Ports Description (Connectors)


This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
RED | GREEN Rings

Low Band

WHITE | BLUE Rings

High Band

Electrical Characteristics

(4x) 7/16-DIN Female Long Neck

1710-2170 MHz Ports

(4x) 7/16-DIN Female Long Neck

Low Band (RED or GREEN)

Frequency Bands (MHz)


Gain (dBi)

790-960 MHz Ports

Tilt 0
Tilt 5
Tilt 10

High Band (WHITE or BLUE)

790...880...960 MHz

1710...1880

1900...2170

16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4

17.8...18.2
17.7...18.0
17.6...17.8

18.2...18.6
18.0...18.5
17.8...18.3

Input Impedance

50

50

VSWR

< 1.5

< 1.5

Polarisation

45

Horizontal Beamwidth (-3 dB)

45

75...68...63

65

62

Vertical Beamwidth (-3 dB)

7.0

5.5

5.0

Electrical Downtilt Range

0-10

0-10

Intra Band Isolation


Isolation Between Bands
Isolation Between Left & Right Arrays
Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back Ratio

> 28 dB

> 30 dB, > 28 dB from 0 to 2 tilt

45 dB Typical

45 dB Typical

> 25 dB for 790-880 MHz


> 28 dB for 880-960 MHz

> 30 dB

18 dB Typical

18 dB Typical

> 30 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

38 | April 2015

(2x) 790-960 / 1710-2170 MHz


5961200 lv
5961200A lv

(lightweight version)

5961200G lv

5961200DG lv

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 17.5 / 18.6 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3 | 59 kg

44 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load
(EN1991-4-1)

Survival: 200 km/h

at 150 km/h

Frontal: 990 N

Lateral: 555 N

Rear: 920 N

Highest value: 1450 N at 110

at 160 km/h

Frontal: 1130 N

Lateral: 630 N

Rear: 1045 N

Highest value: 1650 N at 110

Mounting Kit Options

Part Number

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

790-960 MHz

GREEN

790-960 MHz

BLUE

1710-2170 MHz

WHITE

1710-2170 MHz

2683

432

RED

153

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

1865

Location of the MDCU or MDDU


for RET Control

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 39

(2x) 698-960 MHz


5920300
5920300A

5920300G

5920300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 17.5 dBi | Variable Tilt

Twin low band, dual polarisation, 4 connectors


Independent tilt on each band 0-10
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5920300

Remote Electrical Tilt AISG1.1

5920300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5920300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator

5920300DG

Access Ports Description (Connectors)


This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded
connectors located at the bottom face. See image on the following page.

R1

R2

Ultra Low Band

698-960 MHz Ports

Electrical Characteristics

R1-R2

Frequency Bands (MHz)


Gain (dBi)

(4x) 7/16-DIN Female Long Neck

Tilt 0
Tilt 5
Tilt 10

700

800

900

15.5
15.5
15.2

16.5
16.4
16.2

17.4
17.3
17.0

Input Impedance

50

VSWR

< 1.5

Polarisation

45

Horizontal Beamwidth (-3 dB)

75

Vertical Beamwidth (-3 dB)

8.6

68

65

7.5

6.7

Electrical Downtilt Range

0-10

Inter/Intra Band Isolation

> 30 dB, > 28 dB from 0 to 2 tilt

Upper Sidelobe Rejection


(20 sector above main beam)
Front-to-Back
Ratio

18 dB Typical

@ 180
@ 180 30

> 30 dB
> 25 dB

Maximum Power (Per Port)

250 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

40 | April 2015

(2x) 698-960 MHz


5920300
5920300A

5920300G

5920300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 17.5 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

2863 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

35 kg

Shroud

Outdoor Fibreglass, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h

Frontal: 990 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 555 N

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
66 kg
Includes 0900181/00 Kit

Rear: 920 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

698-960 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 41

(2x) 790-960 MHz


5920200
5920200A

5920200G

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 17.5 dBi | Variable Tilt
Twin 900 MHz antenna, dual polarisation, 4 connectors
Independent tilt on each band 0-10

LTE Ready

MET and RET versions, AISG1.1 or 3GPP/AISG2.0


Single RET module to control both tilt angles, fully inserted inside the antenna (field replaceable)

Ordering Options

Model Number

Manual Electrical Tilt

5920200

Remote Electrical Tilt AISG1.1

5920200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5920200G

Access Ports Description (Connectors)


This antenna is built with two identical 900 MHz Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded
connectors located at the bottom face. See image on the following page.
RED Rings

Ultra Low Band Right

790-960 MHz Ports

(2x) 7/16-DIN Female Long Neck

GREEN Rings

Ultra Low Band Left

790-960 MHz Ports

(2x) 7/16-DIN Female Long Neck

Electrical Characteristics

RED or GREEN Ports

Frequency Bands (MHz)


Gain (dBi)

790...880...960 MHz

Tilt 0
Tilt 5
Tilt 10

16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4

Input Impedance

50

VSWR

< 1.4

Polarisation

45

Horizontal Beamwidth (-3 dB)

65 (6)

Vertical Beamwidth (-3 dB)

7.3

Electrical Downtilt Range

0-10

Intra Band Isolation

> 30 dB, > 28 dB from 0 to 2 tilt

Isolation Between Left & Right Arrays

> 30 dB

Upper Sidelobe Rejection


(20 sector above main beam)

18 dB Typical

Null Fill (First Null Below Main Beam)

< 20 dB

Front-to-Back Ratio

> 30 dB

Maximum Power (Per Port)

200 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET Module Part Number


(one per antenna)

MDCU-A0000

for AISG1.1 protocol (one unit included in 5920200A)

MDCU-G0000

for 3GPP/AISG2.0 protocol (one unit included in 5920200G)

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

42 | April 2015

(2x) 790-960 MHz


5920200
5920200A

5920200G

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 17.5 dBi | Variable Tilt
Mechanical Characteristics
Dimensions (Height x Width x Depth)

2700 x 442 x 152 mm

Weight (Excluding Mounting Accessories)

45 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 160 km/h

Frontal: 1300 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 220 N

Rear: 1700 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

Not available

---

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU


for RET Control

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

790-960 MHz

GREEN

790-960 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 43

(2x) 790-960 MHz


5920200 lv
5920200A lv

(lightweight version)

5920200G lv

5920200DG lv

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 17.5 dBi | Variable Tilt

Twin 800-900 antenna, dual polarisation, 4 connectors


Independent tilt on each band 0-10
Lightweight TwinLine platform
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

LTE Ready

EXTREMELY PROFILED - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5920200 lv

Remote Electrical Tilt AISG1.1

5920200A lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5920200G lv

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G20G22)

5920200DG lv

Access Ports Description (Connectors)


This antenna is built with two identical Extended Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colourcoded connectors located at the bottom face. See image on the following page.
RED Rings

Extended Low Band

790-960 MHz Ports

GREEN Rings

Extended Low Band

790-960 MHz Ports

Electrical Characteristics

(2x) 7/16-DIN Female Long Neck


Low Band (RED or GREEN Ports)

Frequency Bands (MHz)


Gain (dBi)

(2x) 7/16-DIN Female Long Neck

790...880...960 MHz

Tilt 0
Tilt 5
Tilt 10

16.5...17.0...17.5
16.5...17.0...17.5
16.4...16.9...17.4

Input Impedance

50

VSWR

< 1.5

Polarisation

45

Horizontal Beamwidth (-3 dB)

73...68...63

Vertical Beamwidth (-3 dB)

7.3

Electrical Downtilt Range

0-10

Inter/Intra Band Isolation

> 28 dB

Upper Sidelobe Rejection


(20 sector above main beam)

18 dB Typical

Front-to-Back Ratio

> 30 dB

Maximum Power (Per Port)

200 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

44 | April 2015

(2x) 790-960 MHz


5920200 lv
5920200A lv

(lightweight version)

5920200G lv

5920200DG lv

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 17.5 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

2683 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

Carton Box
2.93 x 0.55 x 0.28 m
0.45 m3
51 kg
Includes 0900181/00 Kit

37 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h (EN1991-4-1)

Frontal: 990 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 555 N

Rear: 920 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.
1983

RED

790-960 MHz

GREEN

790-960 MHz

1865
153
432

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 45

(2x) 698-960 / 1695-2180 / 2490-2690 MHz


5978600
5978600A

5978600G

5978600DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 16.5 / 17.5 / 18.0 dBi | Variable Tilt

Twin tri band antenna, dual polarisation, 12 connectors


Independent tilt on each band 0-10 / 0-10 / 0-10
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5978600

Remote Electrical Tilt AISG1.1

5978600A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5978600G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator

5978600DG

Access Ports Description (Connectors)


This antenna is built with two identical Tri Band Antennas, housed side-by-side in the same shroud. The antenna has 12 colour-coded
connectors located at the bottom face. See image on the following page.

R1

R2

Ultra Low Band

698-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

B1

B2

Wide Band

1695-2180 MHz Ports

(4x) 7/16-DIN Female Long Neck

Y1

Y2

LTE 2600

2490-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)

Tilt 0
Tilt 5
Tilt 10

R1-R2

B1-B2

Y1-Y2

700

800

900

1800

2100

2600

14.5
14.5
14.2

15.5
15.4
15.1

16.4
16.3
16.0

17.4
17.4
17.4

17.7
17.7
17.6

18.0
18.0
17.7

Input Impedance

50

50

50

VSWR

< 1.5

< 1.5

< 1.5

Polarisation

45

45

45

Horizontal Beamwidth (-3 dB)

75

68

65

65

63

61

Vertical Beamwidth (-3 dB)

12

10

9.4

6.1

5.3

4.2

Electrical Downtilt Range

0-10

0-10

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from 0 to 2 tilt

> 30 dB
> 28 dB from
0 to 2 tilt

18 dB Typical

18 dB Typical

18 dB Typical

> 30 dB
> 25 dB

> 30 dB
> 25 dB

> 30 dB
> 25 dB

Maximum Power (Per Port)

250 W

200 W

200 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

< -110 dBm

Inter/Intra Band Isolation


Upper Sidelobe Rejection
(20 sector above main beam)
Front-to-Back
Ratio

0-10

@ 180
@ 180 30

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.

RET-Ready Actuator
(one per antenna)

Multi-Device Control
Unit (MCDU)

The MDCU is an electronic module that allows the remote control of the electrical
downtilt (RET) in Amphenol antennas with factory embedded motors. Refer to
ordering options.

Multi-Device Dual Unit


(MDDU)

The MDDU allows two separate RET Controllers to independently drive the RETs in
antennas with factory embedded motors (for antenna sharing or two technologies).
Refer to ordering options.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

46 | April 2015

(2x) 698-960 / 1695-2180 / 2490-2690 MHz


5978600
5978600A

5978600G

5978600DG

Twin Tri Band | Panel Antenna | (2x) XXX-Pol | 65 / 65 / 65 | 16.5 / 17.5 / 18.0 dBi | Variable Tilt
Environmental

Packaging

Operating Temperature Range

-40 C to +60 C

Environmental

Carton Box
2.15 x 0.55 x 0.28 m
0.33 m3
50 kg
Includes 0900181/00 Kit

ETS 300 019

RoHS Compliant

Yes

Mechanical Characteristics
Dimensions (Height x Width x Depth)

1915 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

40 kg

Shroud

Outdoor Fibreglass, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h

Frontal: 635 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 395 N

Rear: 656 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

698-960 MHz

BLUE

1695-2180 MHz

YELLOW

2490-2690 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 47

(2x) 698-960 / 1695-2690 MHz


5963300
5963300A

5963300G

5963300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 16.5 / 18.5 dBi | Variable Tilt

Twin dual band antenna, dual polarisation, 8 connectors


Independent tilt on each band 0-10 / 0-10
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5963300

Remote Electrical Tilt AISG1.1

5963300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5963300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator

5963300DG

Access Ports Description (Connectors)


This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.

R1

R2

Ultra Low Band

698-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

Y1

Y2

Ultra Wide Band

1695-2690 MHz Ports

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics
Frequency Bands (MHz)
Gain (dBi)

Tilt 0
Tilt 5
Tilt 10

R1-R2

Y1-Y2

700

800

900

1800

2100

2600

14.5
14.5
14.2

15.5
15.4
15.1

16.4
16.3
16.0

17.7
17.7
17.7

18.1
18.1
18.0

18.5
18.5
18.2

Input Impedance

50

50

VSWR

< 1.5

< 1.5

Polarisation

45

45

Horizontal Beamwidth (-3 dB)

75

68

65

65

63

61

Vertical Beamwidth (-3 dB)

12

10

9.4

6.1

5.3

4.2

Electrical Downtilt Range

0-10

0-10

Inter/Intra Band Isolation

> 30 dB, > 28 dB from 0 to 2 tilt

> 30 dB, > 28 dB from 0 to 2 tilt

18 dB Typical

18 dB Typical

> 30 dB
> 25 dB

> 30 dB
> 25 dB

Maximum Power (Per Port)

250 W

200 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

Upper Sidelobe Rejection


(20 sector above main beam)
Front-to-Back
Ratio

@ 180
@ 180 30

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

48 | April 2015

(2x) 698-960 / 1695-2690 MHz


5963300
5963300A

5963300G

5963300DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 65 / 65 | 16.5 / 18.5 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

1915 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

33 kg

Shroud

Outdoor Fibreglass, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h

Frontal: 635 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 395 N

Carton Box
2.15 x 0.55 x 0.28 m
0.33 m3
43 kg
Includes 0900181/00 Kit

Rear: 656 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

698-960 MHz

YELLOW

1695-2690 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 49

(2x) 790-960 / 1710-2170 MHz


5963200
5963200A

5963200G

5963200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68 / 68 | 16.5 / 18.1 dBi | Variable Tilt

Twin dual band antenna, dual polarisation, 8 connectors


Independent tilt on each band 0-10 / 0-10
TwinLine platform with multi-array capability
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies
Ordering Options

Model Number

Manual Electrical Tilt

5963200

Remote Electrical Tilt AISG1.1

5963200A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5963200G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator (MDDU-G10G12)

5963200DG

Access Ports Description (Connectors)


This antenna is built with two identical Dual Band Antennas, housed side-by-side in the same shroud. The antenna has 8 colour-coded
connectors located at the bottom face. See image on the following page.
RED | GREEN Rings

Low Band

790-960 MHz Ports

(4x) 7/16-DIN Female Long Neck

WHITE | BLUE Rings

High Band

1710-2170 MHz Ports

(4x) 7/16-DIN Female Long Neck

Electrical Characteristics

Low Band (RED or GREEN)

Frequency Bands (MHz)


Gain (dBi)

Tilt 0
Tilt 5
Tilt 10

High Band (WHITE or BLUE)

790...880...960 MHz

1710...1880

1900...2170

15.5...16.0...16.5
15.5...16.0...16.5
15.4...15.9...16.4

17.3...17.6
17.2...17.4
17.2...17.3

17.6...18.1
17.4...17.9
17.3...17.7

Input Impedance

50

50

VSWR

< 1.5

< 1.5

Polarisation

45

45

Horizontal Beamwidth (-3 dB)

72...68...65

65

Vertical Beamwidth (-3 dB)

Electrical Downtilt Range

0-10

0-10

Intra Band Isolation

> 25 dB

> 28 dB

Isolation Between Bands

> 30 dB

> 30 dB

Isolation Between Left & Right Arrays

> 30 dB

> 30 dB

18 dB Typical

18 dB Typical

Upper Sidelobe Rejection


(20 sector above main beam)
Front-to-Back Ratio

64
6

> 30 dB

> 30 dB

Maximum Power (Per Port)

200 W

160 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control
RET-Ready
Unit (MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

50 | April 2015

(2x) 790-960 / 1710-2170 MHz


5963200
5963200A

5963200G

5963200DG

Twin Dual Band | Panel Antenna | (2x) XX-Pol | 68 / 68 | 16.5 / 18.1 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

1920 x 442 x 152 mm

Weight (Excluding Mounting Accessories)

Carton Box
2.23 x 0.55 x 0.28 m
0.343 m3 | 52 kg

41.5 kg

Shroud

Outdoor Plastic, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load
(EN1991-4-1)

Survival: 200 km/h

at 150 km/h

Frontal: 945 N

Lateral: 320 N

Rear: 886 N

at 160 km/h

Frontal: 1075 N

Lateral: 365 N

Rear: 1008 N

Mounting Kit Options

Part Number

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control
Tilt indicators covered by transparent caps.
Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

790-960 MHz

GREEN

790-960 MHz

BLUE

1710-2170 MHz

WHITE

1710-2170 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 51

(2x) 698-960 MHz


5918300
5918300A

5918300G

5918300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 16.5 dBi | Variable Tilt

Twin low band, dual polarisation, 4 connectors


Independent tilt on each band 0-10
Lightweight TwinLine platform and low windload
MET and RET versions, AISG1.1 or 3GPP/AISG2.0
Fully internal RET control based on our patented technologies (field replaceable)

OPTIMAL PROFILE - LOW WINDLOAD


Ordering Options

Model Number

Manual Electrical Tilt

5918300

Remote Electrical Tilt AISG1.1

5918300A

Remote Electrical Tilt 3GPP/AISG2.0 with an MDCU RET Actuator

5918300G

Remote Electrical Tilt 3GPP/AISG2.0 with an MDDU RET Actuator

5918300DG

Access Ports Description (Connectors)


This antenna is built with two identical Low Band Antennas, housed side-by-side in the same shroud. The antenna has 4 colour-coded
connectors located at the bottom face. See image on the following page.

R1

R2

Ultra Low Band

698-960 MHz Ports

Electrical Characteristics

R1-R2

Frequency Bands (MHz)


Gain (dBi)

(4x) 7/16-DIN Female Long Neck

Tilt 0
Tilt 5
Tilt 10

700

800

900

14.5
14.5
14.2

15.5
15.4
15.1

16.4
16.3
16.0

Input Impedance

50

VSWR

< 1.5

Polarisation

45

Horizontal Beamwidth (-3 dB)

75

Vertical Beamwidth (-3 dB)

12

68

65

10

9.4

Electrical Downtilt Range

0-10

Inter/Intra Band Isolation

> 30 dB, > 28 dB from 0 to 2 tilt

Upper Sidelobe Rejection


(20 sector above main beam)
Front-to-Back
Ratio

18 dB Typical

@ 180
@ 180 30

> 30 dB
> 25 dB

Maximum Power (Per Port)

250 W

Intermodulation
3rd Order for 2x20W Carriers

< -110 dBm

Electrical Downtilt Control


Electrical downtilt for each band can be controlled separately. Tilt indicator(s) are covered by removable transparent cap(s).
Manual Electrical Tilt (MET)
Control

A coloured knob at the end of the tilt indicator allows change of the tilt without need of a tool. The knob colour
is identical to the corresponding connector ring colour. To access the knob, remove the cap by turning it counterclockwise. It is re-installed by opposite rotation. Do not remove the transparent cap(s) from the antenna.

Remote Electrical Tilt (RET)


Control

The remote control of the electrical tilt is managed by either a Multi-Device Control Unit (MDCU) or a Multi-Device
Dual Unit (MDDU) inserted in the bottom of the antenna. A single actuator individually controls the tilt of each
band (no need for daisy chain cables between the bands). This module does not add any additional length to the
antenna. For RET control, the transparent caps must be in place and locked. The tilt angle indicators always remain
visible and the antenna still has manual tilt control (manual override).

RET-Ready antennas are delivered with the RET Actuator (MDCU or MDDU) already installed and pre-commissioned with all antenna
parameters. Every RET device is factory configured and calibrated so the antenna is ready to be used once delivered to the site which means
that there is no need for further installation of RET devices or for programming their configuration or for running a calibration process.
Multi-Device Control Unit
RET-Ready
(MCDU)
Actuator
(one per antenna) Multi-Device Dual Unit
(MDDU)

The MDCU is an electronic module that allows the remote control of the electrical downtilt (RET) in
Amphenol antennas with factory embedded motors. Refer to ordering options.
The MDDU allows two separate RET Controllers to independently drive the RETs in antennas with
factory embedded motors (for antenna sharing or two technologies). Refer to ordering options.

Environmental
Operating Temperature Range
Environmental
RoHS Compliant

-40 C to +60 C
ETS 300 019
Yes

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

52 | April 2015

(2x) 698-960 MHz


5918300
5918300A

5918300G

5918300DG

Twin Band | Panel Antenna | (2x) X-Pol | 65 | 16.5 dBi | Variable Tilt
Mechanical Characteristics

Packaging

Dimensions (Height x Width x Depth)

1915 x 432 x 153 mm

Weight (Excluding Mounting Accessories)

24 kg

Shroud

Outdoor Fibreglass, Grey RAL7035

Wind Speed

Operational: 160 km/hr

Wind Load at 150 km/h

Frontal: 635 N

Mounting Kit Options

Part Number

Survival: 200 km/h

Lateral: 395 N

Carton Box
2.15 x 0.55 x 0.28 m
0.33 m3
34 kg
Includes 0900181/00 Kit

Rear: 656 N

Weight

All mounting bracket kits are ordered separately unless otherwise indicated. Select from the options listed below.
Brackets for pole 48 to 115 mm

0900181/00

3.4 kg

Brackets for pole 70 to 150 mm

0900182/00

3.9 kg

Kit to add mechanical tilt to above brackets

0900396/00

2.3 kg

Bottom View of Antenna

Dimensions (in mm)

Location of the MDCU or MDDU


for RET Control

Tilt indicators covered by transparent caps.


Manual adjustment is accessed by removing the caps.
Knob colours are the same as the connectors.

RED

698-960 MHz

Installation
In order to operate RET control, the transparent
caps covering the tilt adjustment indicators must
be engaged and locked. Do not cut them from the
antenna.
Always attach the antenna by the two mounting points.
Do no install the antenna with the connectors facing upward.

Several patents pending regarding this product. Quoted performance parameters are provided to offer typical, peak or range values only and may vary as a result of normal testing, manufacturing and operational
conditions. Extreme operational conditions and/or stress on structural supports is beyond our control. Such conditions may result in damage to this product. Improvements to products may be made without notice.

April 2015 | 53

You might also like