Professional Documents
Culture Documents
SECTION
BCS
CONTENTS
SERVICE INFORMATION ............................ 2
BCS
BCS-1
D40
MODIFICATION NOTICE
< SERVICE INFORMATION >
SERVICE INFORMATION
MODIFICATION NOTICE
Major Modification Item
INFOID:0000000007561090
The system description has been changed by rear fog lamp system has been added.
The schematic of body control system has been changed.
BCM configuration list has been changed.
BCS-2
D40
A
INFOID:0000000007740459
Description
BCM reads combination switch (lighting switch, wiper switch) status, and controls various electrical component according to the result.
BCM reads information of a maximum of 20 switches by combining five output terminals (OUTPUT 1 - 5)
and five input terminals (INPUT 1 - 5).
Operation Description
BCM periodically outputs pulse from the five input terminals
(INPUT 1 - 5) simultaneously.
G
PKID0801E
BCM periodically activates the transistor (output terminal side) in descending order (OUTPUT 5 4 3
2 1).
NOTE:
BCM changes transistor activation frequency under the sleep status.
Normal status
When BCM is in the normal status, the transistor activates every 10ms.
Sleep status
When BCM is in the sleep status, BCM enters power save mode. The transistor activates every 30ms.
BCS
PKID0605E
BCS-3
D40
PKID0802E
JMMIA0987GB
JMMIA0988GB
NOTE:
Headlamp system has a dual circuit.
Front Wiper Intermittent Operation
Front wiper intermittent operation is determined from a combination of 3 switches (INT VOLUME 1, 2, and 3)
and vehicle speed signal.
Wiper Intermittent Dial Position Setting
BCS-4
D40
Intermittent operation
interval
INT VOLUME 1
INT VOLUME 2
INT VOLUME 3
Short
ON
ON
ON
ON
ON
OFF
2
3
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
OFF
Long
1.
2.
3.
4.
5.
TAIL LAMP switch joint in combination switch turns ON when setting lighting switch to 1ST.
Current flows from INPUT4 when activating the OUTPUT5 transistor.
BCM judges the lighting switch position as 1ST when detecting voltage change by flowing the current.
BCM transmits position lights request signal to IPDM E/R with CAN communication.
BCM judges that lighting switch holds the position as 1ST when detecting voltage change by activating
the OUTPUT5 transistor again.
BCS
JMMIA0989GB
NOTE:
Each OUTPUT terminal transistor is activated at 10 ms intervals. Therefore, after switch is turned ON, the
electrical loads are activated with a time delay. However, this time delay is so short that it cannot be noticed.
Reference
LT-3
BCS-5
D40
Schematic
INFOID:0000000007740460
JMKWA2359GB
BCS-6
D40
BCS
O
JMKWA2383GB
Configuration list
INFOID:0000000007561098
BCS-7
D40
NOTE
Items
Setting value
KEYLESS ENTRY
WITH WITHOUT
H/L BULB
H4 HALOGEN DEFAULT
HANDLE
RHD LHD
THEFT ALARM
WITH WITHOUT
NOTE
Items
Setting value
AUTO LIGHT
WITHOUT
FR FOG LAMP
WITH
RR FOG LAMP
WITHOUT
SPEED SIGNAL
MODE1
FOR AUSTRALIA
MANUAL SETTING ITEM
NOTE
Items
Setting value
KEYLESS ENTRY
WITH WITHOUT
NOTE
Items
Setting value
THEFT ALARM
WITHOUT
H/L BULB
H4 HALOGEN
AUTO LIGHT
WITHOUT
FR FOG LAMP
WITH
RR FOG LAMP
WITHOUT
HANDLE
RHD
DTRL
WITHOUT
RAIN SENSOR
WITHOUT
REAR WIPER
WITHOUT
H/L WASHER
WITHOUT
DONGLE
WITHOUT
ACU ALARM
KEY WARNING
MODE1
Setting value
H/L BULB
H4 HALOGEN
NOTE
BCS-8
D40
NOTE
Items
Setting value
WITHOUT
THEFT ALARM
WITHOUT
AUTO LIGHT
WITHOUT
FR FOG LAMP
WITH
RR FOG LAMP
WITH
HANDLE
RHD
RAIN SENSOR
WITHOUT
ACU ALARM
BCS
BCS-9
D40