Professional Documents
Culture Documents
Cable Specifications
If you prefer to build your own cables, this appendix provides cable specifications for the Cisco ASR 901
router.
This appendix includes the following sections:
Warning
To comply with the Telcordia GR-1089 NEBS standard for electromagnetic compatibility and safety,
use only shielded cables that are grounded on both ends for Type 2 and Type 4 ports that require
shielded cables.
205053
12345678
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
OL-23778-01
B-1
Appendix B
Cable Specifications
Table B-1
Pin
FE Signal
GE Signal
TX data+
TX A+
TX data
TX A
RX data+
RX B+
Not used
TX C+
Not used
TX C
RX data
RX B
Not used
RX D+
Not used
RX D
Note
Pins not listed in the tables in this appendix are not connected
87654321
RJ-48C connector
RJ-48C Connector
24939
Figure B-2
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
B-2
OL-23778-01
Appendix B
Cable Specifications
Console Port Signals and Pinouts
Figure B-3 shows the RJ-48C connector wiring for the T1/E1 cable.
Figure B-3
H11419
Note
Pin
Signal Name
Direction
Description
RX Tip
Input
Receive Tip
RX Ring
Input
Receive Ring
Not used
TX Tip
Output
Transmit Tip
TX Ring
Output
Transmit Ring
Not used
Not used
Not used
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
OL-23778-01
B-3
Appendix B
Cable Specifications
RJ-45-to-RJ-45
rollover cable
RJ-45-to-DB-9 adapter
(labeled TERMINAL)
H7226
Router
Table B-3 lists the Console port pinouts for the Cisco ASR 901 router.
Table B-3
Pin
Signal Name
HP Pins
Direction
Description
RTS
UART_RTS1
Output
Request to send
DTR
NC
TXD
UART_SOUT1
Output
Transmit data
RI
GND
GND
GND
RXD
UART_SIN1
Input
Receive data
DSR/DCD
NC
Input
CTS
UART_CTS1
Input
Clear to send
Ring indicator
Table B-4 describes the pinouts RJ-45-to-RJ-45 and RJ-45-to-DB-9 rollover cables.
Table B-4
Console
Port (DTE)
RJ-45-to-DB-9
Terminal Adapter
(Connected to Rollover
Cable)
Signal
RJ-45 Pin
RJ-45 Pin
DB-9 Pin
Signal
CTS
Console
Device
RTS
DTR
DSR/DCD
TxD
RxD
GND/RI
GND
GND
GND/RI
RxD
TxD
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
B-4
OL-23778-01
Appendix B
Cable Specifications
Console Port Signals and Pinouts
Table B-4
Console
Port (DTE)
RJ-45-to-DB-9
Terminal Adapter
(Connected to Rollover
Cable)
Signal
RJ-45 Pin
RJ-45 Pin
DB-9 Pin
Signal
DSR/DCD
DTR
CTS
81
RTS
Console
Device
Table B-5 lists the pinouts for the asynchronous serial console port, the RJ-45-to-RJ-45 rollover cable,
and the RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL).
Table B-5
Console
Port (DTE)
RJ-45-to-DB-25
Terminal Adapter
Console
Device
Signal
RJ-45 Pin
RJ-45 Pin
DB-25 Pin
Signal
CTS
RTS
DTR
DSR/DCD
TxD
RxD
GND/RI
GND
GND
GND/RI
RxD
TxD
DSR/DCD
20
DTR
RTS
CTS
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
OL-23778-01
B-5
Appendix B
Cable Specifications
Figure B-5
H3824
Pin 8
Pin
Signal Name
Direction
Description
RX ring
Input
Receive ring
RX tip
Input
Not connected
TX ring
Output
Transmit ring
TX tip
Output/input
Not connected
Not connected
Not connected
Pin
Signal Name
Direction
Description
Not connected
Not connected
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
B-6
OL-23778-01
Appendix B
Cable Specifications
GPS Port Pinouts
Table B-7
Pin
Signal Name
Direction
Description
Not connected
Ground
Ground
Not connected
TOD_N
Output/Input
TOD_P
Output/Input
Note
For pinouts related to ToD and 1PPS using the BITS interface, see Console Port Signals and Pinouts.
Table B-8
10 Mhz
1PPS
InputSine wave
InputPulse shape
OutputSquare wave
OutputPulse shape
Impedance
50 ohms
50 ohms
Pulse Width
26 microseconds
Rise Time
InputAC coupled
40 nanoseconds
Waveform
Amplitude
Output5 nanoseconds
The 1PPS interface type is Series 1.0 / 2.3, 200 ohms.
For instructions on how to configure the 10 Mhz and 1PPSs ports, see the Cisco ASR 901 router Mobile
Wireless Software Configuration Guide.
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
OL-23778-01
B-7
Appendix B
Cable Specifications
Open means that the normal condition has current flowing through the contact (referred to as
normally closed contact). The alarm is generated when the current stops.
Closed means that no current flows through the contact (referred to as normally open contact). The
alarm is generated when the current flows.
The alarm input is a dry-contact alarm port. You can connect up to four alarm inputs from devices, such
as a door, a temperature gauge, or a fire alarm, to the alarm port. You can use the CLI to set the alarm
severity to minor, major, or critical. An alarm generates a system message.
Note
353579
12345678
Table B-9 list the pinouts for the alarm port (RJ45) on the Cisco ASR 901 router.
Table B-9
Pin
Signal Name
Alarm input 1
Alarm input 2
Description
Not connected
Alarm input 3
Alarm input 4
Not connected
Not connected
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
B-8
OL-23778-01
Appendix B
Cable Specifications
Management Ethernet Port Pinouts
Pin
Signal Name
RxD_P
RxD_N
TxD_P
Description
Not connected
Not connected
TxD_N
Not connected
Not connected
Auxiliary Port
Auxiliary port is not supported on the Cisco ASR 901 router and you should not try to configure the
auxiliary port.
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
OL-23778-01
B-9
Appendix B
Cable Specifications
Auxiliary Port
Cisco ASR 901 Series Aggregation Services Router Hardware Installation Guide
B-10
OL-23778-01