Professional Documents
Culture Documents
UG-702
One Technology Way P.O. Box 9106 Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 www.analog.com
GENERAL DESCRIPTION
This user guide describes the evaluation board that contains the
Analog Devices, Inc., ADA2200 sampled analog, synchronous
demodulator. The circuit configurations available through the
ADA2200-EVALZ enable the user to exercise its full set of features.
The ADA2200-EVALZ simplifies signal connections to standard
test equipment. Inputs, outputs, supplies, and other circuit test
12359-001
Figure 1.
Rev. 0 | Page 1 of 10
UG-702
TABLE OF CONTENTS
Evaluation Board Features ............................................................... 1
REVISION HISTORY
8/14Revision 0: Initial Version
Rev. 0 | Page 2 of 10
UG-702
4.
3.
5.
6.
7.
Position
1 and 2
2 and 3
2 and 3
Description
IN+ connected to INP
IN connected to VOCM
On-board clock selected
RCK OUTPUT
P9
50
CLK INPUT
P4
50
P13
TRIG
SYNC OUTPUT
P10
50
CH1
CH2
VW
2
CH1 5.00V
FUNCTION
GENERATOR
TRIG
50
IN+
P2
P5
OUT
VOCM
ADA2200
1.58k
P12
50
P6
RESET
I/Q
SEL
M2.00m s
T
3.92000m s
A CH1
3.00V
DMM
20F
P11
20F
0V TO 3.0V
IN
P3
CH2 100m V
OUT+
P7
1.58k
CONFIG
EEPROM
OUT
P8
USB
(POWER ONLY)
12359-002
2.
00000-000
1.
Figure 2. Suggested Configuration for Quick Start, Showing Connections to Standard Test Equipment
Rev. 0 | Page 3 of 10
UG-702
Rev. 0 | Page 4 of 10
Signal
+5V
IN+
IN
CLKIN
OUT+
OUT
RCK
SYNCO
OUTP
OUTN
+5V
GND
VOCM
BOOT
ISUPPLY
A0
SCL
SDA
Description
Mini-B USB power connector
Noninverting input
Inverting input
External clock input
Noninverted filtered output
Inverted filtered output
Reference clock output
Output synchronization pulse
Noninverted demodulated output
Inverted demodulated output
Mini-B USB power connector
Multiple ground test points
Output common-mode voltage I/O
Boot from EEPROM signal (digital)
10 current shunt for 3.3 V supply
EEPROM address selection
EEPROM clock
EEPROM data
UG-702
To program the ADA2200 via the SPI, use the ADA2200SDPEVALZ evaluation board.
Description
Master clock
Input sampling rate
Input sampling Nyquist rate
Output sampling rate
Output sampling Nyquist rate
Synchronization pulse frequency
Reference clock frequency
Band-pass filter center frequency
Mixer frequency
10
GAIN (dB)
Ratio
1
1
1/2
1/8
1/16
1/8
1/64
1/64
1/64
20
30
40
50
0.25
0.5
0.75
NORMALIZED FREQUENCY (Hz/Nyquist)
12359-003
UG-702
The filter transfer function scales with the input clock frequency.
Valid input clock frequencies range from 10 kHz to 1 MHz.
Sweeping the input clock frequency in this range sweeps the
filter center frequency from 156.25 Hz to 15.625 kHz. The filter
Q remains constant at 1.7 for any CLKIN frequency.
Amplitude Measurements
SIGNAL MEASUREMENTS
The signal present at the output of the ADA2200 depends on
the amplitude and phase (relative to the reference clock) of the
signal applied at its inputs. When either the amplitude or phase
is known and constant, any output variations can be attributed
to the modulated parameter.
This dependence is shown in Figure 4. In any of these cases,
the ADA2200 is performing either amplitude or phase
demodulation.
A1
90
A2
180
270
90
PHASE (degrees)
180
270
12359-004
AMPLITUDE (V)
A2
Phase Measurements
If the amplitude of the signal present at the inputs of ADA2200
remains constant, the output varies as a function of the relative
phase between the signal and the reference clock (RCLK).
As long as the phase shifts are small, this relationship is
approximately linear; however, the gain (slope) of this
relationship depends on the relative phase shift between the
signal and RCLK. For example, if the phase shift occurs around
the crest of the signal, the change at the output is barely
noticeable. In addition, the user is not able to distinguish
between a positive and a negative shift. In contrast, the
maximum phase sensitivity is achieved when the phase shift
happens around the zero crossing. Because these two points are
90 from each other, they are in quadrature.
A1
Rev. 0 | Page 6 of 10
UG-702
A = I 2 + Q2
= sin1(Q/A)
Or, alternatively:
= cos1(I/A)
The inverse sine or inverse cosine functions involving the I and Q
components linearize the relationship between the phase of the
signal and the measured angle. This calculation also makes it
possible to separate the effects of amplitude and phase variations.
A
Q
Because the inverse sine and inverse cosine are only defined in
two quadrants, the sign of the I and Q components must be
taken into account to map the result to cover the entire 360.
IV
12359-005
III
If the signal amplitude and phase are relatively constant for the
duration of the measurement, it is possible to switch the ADA2200
to return the I and Q components. On the ADA2200-EVALZ,
Rev. 0 | Page 7 of 10
UG-702
3
600OHM
C1
10F
G1
G2
G3
G4
C4
1F
VIN
EN
NC
U1
VOUT
3V3
GND
2
C6
0.1F
C9
10F
C7
1F
100
NC001
NC002
GND
PINS
ADP151AUJZ-3.3-R7
E1
1
1
2
3
4
5
R10
1
P1
GND8
DS1
TP7
KELVIN
CONNECTION 1
SML-310MTT86
TP8
R17
10
P2
2
1
P3
3
2
1
R5
C3
R4
DNP
0
2 3 4 5
TBD0805
IN
C5
1F
P11
VDD
OUTP
OUTN
11
10
3
A0
14 SDA
15 SCL
2
16
R9
N3 3
N4 4
100
C8
0.33F
FSM2JSMA
10F
5 4 3 2
10F
P7
1
2
LAYOUT AS
2 2 0.1IN
PATTERN
TP9
TP12
2
1
TP10
ADA2200
LAYOUT AS
2 2 0.1IN
PATTERN
2
1
P12
P8
OUT
R22
R24
49.9
1.58k
R27
3
2
1
P13
RESET
FC=10HZ
1
2
P6
1 N1
2 N2
1.58k
12
CS/A0
RST 9
RST
SDIO/SDA
BOOT 4
SCK/SCL
13 BOOT
SYNCO
RCLK/SDO
1
XOUT
CLKIN
GND
1
VOCM
5015
OUT+
R23
C13
U2
6
INP
7
INN
8
VOCM
1
2
LAYOUT AS
2 2 0.1IN
PATTERN
R21
49.9
C14
1
2
3
C12
C2
TBD0805
R3
2 3 4 5
DNP
C11
1F
FC = 10Hz
10F
C15
P5
R6
IN+
C10
0.1F
5 4 3 2
10F
1M
DNI
1
2
R28
470
Y1
C18
120pF
C19
470pF
SYNCO
R25
3.3V
3
1
P10 49.9
TP6
5015
EEPROM_BOOT
1
1
2
R8
100
5 4 3 2
69157-102
C16
0.01F
OS102011MS2QN1
R2
R26
1
2
P4
1
2
RCK
1
49.9
P9
49.9
5 4 3 2
69157-102
3.3V
R14
10k
10k
R20
10k
R19
R18
DNI
10k
A0
A1
10k
R16
C17
R15
69157-102
0.1F
2 3 4 5
R1
X1
1
2
3
4
1
2
3
4
8
7
6
5
8
7
6
5
SCL
SDA
110-43-308-41-001000
DIP-8 EEPROM SOCKET
EEPROM TO BE INSTALLED:
AT24C02C-PUM
(8-LEAD PDIP OR EQUIVALENT)
Rev. 0 | Page 8 of 10
12359-006
1 CLKIN
UG-702
ORDERING INFORMATION
BILL OF MATERIALS
Table 4.
Qty.
16
6
4
3
1
1
1
1
1
1
1
1
9
3
5
3
5
1
3
1
1
1
1
1
1
1
4
2
1
7
2
2
1
Designator
+5 V, TP6 to TP10, GND1
to GND8, TP12, VOCM
C1, C9, C12 to C15
C4, C5, C7, C11
C6, C10, C17
C16
C18
C19
C8
DS1
E1
EEPROM_BOOT
P1
P2 to P4,P7 to P12
P5, P6, P13
R1, R21, R22, R25, R26
R8 to R10
R14, R16, R18 to R20
R17
R2, R5, R6
R27
R28
RESET
U1
U2
X1
Y1
Corners
R23, R24
Y1
IN+, IN, RCK, OUT+,
OUT, CLKIN, SYNCO
C2, C3
R3, R4
R15
Description
Conn, printed circuit board (PCB) SMT test points
Capacitor, ceramic, monolithic, X5R, 25 V
Capacitor, ceramic, monolithic, X5R, 25 V
Capacitor, ceramic, X7R, 0603, 50 V
Capacitor, ceramic, chip, C0G, 0603, 25 V
Capacitor, ceramic, NP0, 0805, 50 V
Capacitor, ceramic, NP0, 50 V
Capacitor, ceramic, X5R, 16 V
LED, green, surface mount
Inductor chip ferrite bead
Switch, SPDT, PCB mounted slide
Conn, PCB USB mini-B, receptacle ASSY SMT
Conn, PCB Berg jumper, ST, male, 2-pin
Conn, PCB Berg header, ST, male, 3-pin
Resistor, precision thick film chip, R1206
Resistor, precision thick film chip, R0603
Resistor, precision thick film chip, R0603
Resistor, antisurge thick film chip
Resistor, thick film chip
Resistor, precision thick film chip, R0805
Resistor, metal film chip, 0.1%
Switch, tactile, SPST NO
IC, CMOS linear regulator, LDO, 3.3 V
IC, sampled analog filter, synchronous demodulator
Socket, 8-pin, DIP
Ceramic resonator, 400 kHz
Bump on, cylindrical, 0.312X.200, black
Resistor, precision thin film chip, R0603
IC, EEPROM, 2 kb, 1 MHz, 8-DIP
Conn, PCB, coaxial, SMA end launch (not installed)
Manufacturer
Keystone Electronics
Corp.
Murata
Murata
AVX
Kemet
AVX
Phycomp (Yageo)
AVX
ROHM
Murata
ITT
Molex
Berg
Samtec
Panasonic
Multicomp
Panasonic
Panasonic
Panasonic
Panasonic
Panasonic
TE Connectivity
Analog Devices
Analog Devices
Mill-Max
ECS
3M
Panasonic
ATMEL
Johnson
GRM31CR61E106KA12L
GRM188R61E105KA12D
06035C104KAT2A
C0603C103J3GACTU
08055A121JAT2A
2238 861 15471
0603YD334KAT2A
SML-310MTT86
BLM15AX601SN1D
OS102011MS2QN1
54819-0572
69157-102
TSW-103-08-G-S
ERJ-8ENF49R9V
MC 0.063 W, 0603, 1%, 100
ERJ-3EKF1002V
ERJP14F10R0U
ERJ-6GEY0R00V
ERJ-6ENF1004V
ERA-6AEB471V
FSM2JSMA
ADP151AUJZ-3.3-R7
ADA2200
110-43-308-41-001000
ZTB400P
SJ61A1
ERA-3AEB1581V
AT24C02C-PUM
142-0701-851
TBD0805
Panasonic
Panasonic
TBD0805
ERJ-8ENF49R9V
ERJ-3EKF1002V
Rev. 0 | Page 9 of 10
Part No.
5015
UG-702
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the Evaluation Board), you are agreeing to be bound by the terms and conditions
set forth below (Agreement) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (Customer) and Analog Devices, Inc.
(ADI), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
Third Party includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED AS IS AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMERS POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADIS TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
2014 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG12359-0-8/14(0)
Rev. 0 | Page 10 of 10