Professional Documents
Culture Documents
TOPI
C
NO
PAGE
NO
1
2
3
4
5
6
7
LIST OF CONTENTS
Configuration
Before power on instrument
Get start with CMM instrument
PART MANAGER editing
Inner ring dimension measurement
outer ring dimension measurement
Protocol output
Configuration
C.M.M Model:
CRYSTA-PLUS M443
Serial NO:
25710711
Machine No:
CMM-01
MEASURING RANGE:
X axis = 400 mm
Y axis = 400 mm
Z axis = 300 mm
Resolution:
0.0005 mm
Measurement uncertainty:
+/- (
0.5+ L
900 ),
mm)]
Calibration ball diameter: 16.996 mm
Required air pressure:
4 bar
5.5 bar
Switch on pc
Switch on individual slides ensure free movement of probe.
Open
icon from desktop.
It will show window as follows,
Fig.: 01
click on OK and it will show window as follows
Fig.: 02
Now, move measuring probe to the home position. After getting probe position
it will shows window automatically as follows, motion of probe is such that it
moves in all the three directions.
Fig.: 03
Now, the slide sensors are activated and the measurement is allowed to start.
Open icon
It will show the following windows.
Fig.: 04
Fig.: 05
Close startup wizard.
click
icon and select probe from available probe list shown as below,
Fig.: 06
Measure and Align plane:
Click on
icon available in Geopak CMM learn mode window, It will show
window as follow.
Fig.: 07
Fig.: 08
Click on OK, command will make the measured plane as align plane,
Now we can take measurement of the dimension of the inner ring.
Cone angle measurement:
7
Click on
icon.
It will open window as follow,
Fig.: 09
Click on OK after check and ensure that 8 no. of points should be taken.
Measure all 8 points with the help of measuring probe.
Click on
(last element) available in CMM learn mode window to divide the
measured angle of cone half. Type value of measured angle to the below window
which highlight after click on that icon.
Fig.: 10
Place inner ring on the base in such a way that the big face of the inner ring
should touch base plane.
click on
(circle element).
Set the parameters as shown below,
Fig.: 11
Name can be changed in upper shown window. Click on OK. It will show the
window as follow,
Fig.: 12
ID DIAMETER MEASUREMENT:
CLICK ON
Fig.: 13
No. of point and the measuring parameter should be cross checked as per
above window and then after click on OK. It will show window as follow.
Fig.: 14
10
Make contact of the measuring probe to the id surface. And field of result will
updated with final 4th contact of the measuring probe to the id surface.
Width measurement:
Click on
Fig.: 15
Select Repeat command on if we want to measure width of more than one inner
ring.
11
Fig.: 16
Close startup wizard.
click
icon and select probe from available probe list shown as below,
Fig.: 17
Measure and Align plane:
Click on
icon available in Geopak CMM learn mode window, It will show
window as follow.
12
Fig.: 18
Fig.: 19
Click on OK, command will make the measured plane as align plane,
Now we can take measurement of the dimension of the inner ring.
13
Click on
icon.
It will open window as follow,
Fig.: 20
Click on OK after check and ensure that 8 no. of points should be taken.
Measure all 8 points with the help of measuring probe.
Click on
(last element) available in CMM learn mode window to divide the
measured angle of cone half. Type value of measured angle to the below window
which highlight after click on that icon.
Fig.: 21
14
by click on
(circle element).
Set the parameters as shown below,
Fig.: 22
Name can be changed in upper shown window. Click on OK. It will show the
window as follow,
Fig.: 23
OD DIAMETER MEASUREMENT:
CLICK ON
15
Fig.: 24
No. of point and the measuring parameter should be cross checked as per
above window and then after click on OK. It will show window as follow.
Fig.: 25
Make contact of the measuring probe to the id surface. And field of result will
updated with final 4th contact of the measuring probe to the id surface.
Width measurement:
16
Click on
Fig.: 26
Select Repeat command on if we want to measure width of more than one inner
ring.
Fig.: 27
Save the file to the specified folder in the computer
17
Select required file type to save the measurement, for that click and select it from
output block as above mentioned window.
18