Professional Documents
Culture Documents
DBL 4028
Company Standard
Application note:
In line with the scope, application of the present version of this Standard shall be checked in case of new
vehicle projects or components for which no concept/basic specifications or component requirement
specifications have been approved yet at the date of issue of this version.
The respective contract documents regulate the mandatory application of the present version
of this Standard by the supplier.
Changes
In comparison with edition 2008-11, the following changes have been made:
Concentration of DBL 4028 on material-based specifications.
Supply-specific specifications moved to DBL 4532.
Material designation corrections (Annex Q).
Material 71MnVS4 added.
Copyright Daimler AG
Contents
1
Scope ............................................................................................................................................... 3
2
Normative references ....................................................................................................................... 4
3
Terms and definitions ....................................................................................................................... 4
4
General requirements ....................................................................................................................... 4
5
Abbreviated material designation for documentation ....................................................................... 5
6
Specifications ................................................................................................................................... 5
6.1
Material standards ............................................................................................................................ 5
6.2
Manufacturing process ..................................................................................................................... 5
6.3
Chemical composition....................................................................................................................... 6
6.3.1 Ready-to-install parts ........................................................................................................................ 6
6.3.2 Semi-finished products (input stock, solid forming blanks) .............................................................. 6
6.4
Hardenability ..................................................................................................................................... 7
6.5
Internal soundness ........................................................................................................................... 8
6.5.1 Microscopic degree of purity ............................................................................................................. 8
6.5.2 Macroscopic degree of purity ........................................................................................................... 8
6.6
Austenitic grain size .......................................................................................................................... 8
6.7
Suitability for induction hardening..................................................................................................... 8
7
Tests ................................................................................................................................................. 8
7.1
Test methods .................................................................................................................................... 8
7.1.1 Chemical composition testing ........................................................................................................... 8
7.1.2 Testing the hardenability .................................................................................................................. 9
7.1.3 Testing the internal soundness......................................................................................................... 9
7.1.4 Testing the grain size........................................................................................................................ 9
7.2
Test frequency .................................................................................................................................. 9
7.3
Test certificates............................................................................................................................... 10
7.3.1 Inspection certificate in accordance with DIN EN 10204 (plant certificate) .................................... 10
7.3.2 Test report for ultrasonic immersion technology as per SEP 1927 ................................................ 10
Annex A (normative) Material specification 39MnCrB6-2 mod. (formerly 30MnB5+DBL 4552) ............... 11
Annex B (normative) Material specification 34MnCrMo6-4 ........................................................................ 12
Annex C (normative) Material specification C45E (formerly: Ck45) .......................................................... 13
Annex D (normative) Material specification 38MnS6 ................................................................................. 14
Annex E (normative) Material specification 35MnS4 (formerly: C35 mod.) .............................................. 15
Annex F (normative) Material specification C70S6 .................................................................................... 16
Annex G (normative) Material specification for AFP steels ........................................................................ 17
Annex H (normative) Material specification 30MnVS6+Ti .......................................................................... 18
Annex I (normative) Material specification 36MnVS4 ................................................................................ 19
Annex J (normative) Material specification 35MnVS4-3 (formerly: 38MnVS6mod) .................................. 20
Annex K (normative) Material specification 46MnVNbS5 (formerly: 46MnVS6mod) ................................ 21
Annex L (normative) Material specification 70MnVS4 ............................................................................... 22
Annex M (normative) Material specification 71MnVS4 .............................................................................. 23
Annex N (normative) Material specification 12CrMnMoV7-5 ..................................................................... 24
Annex O (normative) Material specification 19MnB4 mod. ........................................................................ 25
Annex P (informative) Material specification Cf53 (NFN) ........................................................................... 26
Annex Q (informative) Materials not for new designs (NFN)...................................................................... 27
Copyright Daimler AG
Scope
This DBL applies to all quenched and tempered steels, steels for flame hardening and induction
hardening, ferritic-pearlitic steels for precipitation hardening (AFP steels), and other steel types
for controlled cooling from hot-working temperatures, as well as bainitic steels.
Materials as per this DBL are used for component parts that are produced, or whose material properties
are potentially changed, by forming and/or metal cutting.
The relevant DIN, ISO, and EN standards form the basis of this DBL; only those points are mentioned
in this DBL which are stated more precisely, or are more restricted compared with the cited standards,
or which deviate from the specifications contained in these standards. The specifications of this DBL shall
take precedence over any indications contained in DIN, ISO, or EN standards.
All suppliers supplying products manufactured from materials conforming to this DBL shall contact
the customer plant before initial deliveries are made in order to obtain information on the use and further
processing of the products. If required, further specifications shall be agreed or specifications contained
in this DBL adapted to the process or component-specific requirements of the customer plant.
Application example
Steel EN 10083-3 1.7225 +QT
1000-1200 +DBL 4028.00
The product versions of these supply specifications describe the chemical composition and the resulting
material properties and are specified by the development department of Daimler AG.
A material is uniquely described by the material name and/or material number as well as the product
version. In this process, product version .00 describes the basic version of the material as per this DBL.
Additional product versions are not required at this time.
Additional terms of delivery (e.g. surface conditions) for semi-finished products (input stock, solid forming
blanks) are listed in DBL 4532 and are defined by the customer plant.
Copyright Daimler AG
Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any changes) applies.
DIN EN 10020
DIN EN 10083
DIN EN 10160
DIN EN 10168
DIN EN 10204
DIN EN 10263
DIN EN 10267
DIN EN 10277
DIN EN 10308
DIN EN ISO 642
DIN EN ISO 643
DIN EN ISO 15549
DIN ISO 15787
DIN 50602:1985-09
DBL 4532
DBL 4550
DBL 4551
DBL 6714
DBL 8585
MBN 41010
SEP 1664
SEP 1927
General requirements
For safety requirements, homologation (in particular, exhaust emissions) and quality, the existing statutory
requirements and laws shall be complied with. In addition, the relevant requirements of the Daimler Group
apply.
All materials, procedures, processes, components, and systems shall conform to the current statutory
requirements regarding regulated substances and recyclability.
DBL 8585 shall be observed.
Copyright Daimler AG
A material is uniquely described by the material name and/or material number as well as the product
version. In this process, product version .00 describes the basic version of the material as per this DBL.
e.g.
Steel DIN EN 10083-3 1.7225 (42CrMo4) +DBL 4028.00
Steel DBL 4028 71MnVS4 +DBL 4028.00
If required, the heat treatment condition and the tensile strength in megapascals (MPa) to be achieved
by heat treatment can be stated after the material designation.
e.g.
Steel DIN EN 10083-3 1.7225 (42CrMo4) +QT 1000-2000 +DBL 4028.00
For drawing entries without indications of the strength to be achieved by heat treatment, this data shall be
provided based on DIN ISO 15787 in plain text on the drawing.
e.g.
Steel DIN EN 10083-3 1.7225 (42CrMo4) +QT* +DBL 4028.00
*Cooled from hot-working temperatures in a controlled process to a strength of 1000 2000 MPa.
Refer to DBL 4532 and DIN ISO 15787 for the specifications of heat treatment and mechanical properties.
Specifications
6.1
Material standards
6.2
Manufacturing process
Melting process
Electric arc furnace or blast furnace and BOF converter.
Any deviating methods shall be indicated and require approval by the customer plant.
Deoxidation
All steels conforming to this DBL shall be killed.
Copyright Daimler AG
6.3
Chemical composition
Unless otherwise specified, all indications on the chemical composition refer to the melt analysis.
In the case of arbitration the unit analysis with the permissible deviations of the corresponding standard
shall apply.
6.3.1
Ready-to-install parts
For ready-to-install components which are not subjected to further manufacturing or heat treatment
processes at Daimler AG plants, the specifications for the chemical composition indicated in the standards
listed under Section 6.1, or the specifications in accordance with material-specific Annexes A to P shall
apply.
6.3.2
The following additional specifications shall apply to all deliveries of semi-finished products which are
subjected to further manufacturing and/or heat treatment processes at Daimler AG plants:
Sulfur content
Components that do not undergo machining in the customer plant shall be subject to the specifications
for sulfur content as per the standards listed in Section 6.1.
Components that undergo machining in the customer plant shall maintain a controlled sulfur content
of 0,020 to 0,040 %.
The sulfur content of the steels in the material-specific Annexes A to P or according to specific
agreements with the customer plant shall apply, in deviation therefrom.
Trace elements
Trace elements, i.e. all elements that are not listed in the specifications as alloying elements or required
for finish treatment of the melt shall not be purposefully added to the melt without approval by
the customer plant.
Adequate measures shall be taken to prevent use of such elements from scrap or any other substances
used in production which impair the hardenability, mechanical properties, or usability.
In this context, DIN EN 10020, Table 1, only describes the difference between unalloyed and alloyed steel.
The limit values stated therein shall not define a permissible alloy content limit for materials as per this
DBL.
Copyright Daimler AG
0,10 - 0,20 %
0,07 %
0,25 %
0,25 %
0,03 %
0,50 %
0,0050 %
V
Nb
B
Sb
As
Pb
0,009 %
0,008 %
0,0005 %
0,0050 %
0,050 %
0,10 %
6.4
Hardenability
Suppliers shall select the hardenability of components and input stock supplies that are not subject to heat
treatment at Daimler AG plants so that the required mechanical and technical component specifications
are achieved in a reliable process.
The hardenability bands as per material-specific Annexes A to P shall apply to components and input
stock supplies that are subject to heat treatment at the Daimler AG plants. If the material is not defined
in the material-specific Annexes A to P, the hardenability bands of the standards listed in Section 6.1 shall
apply.
Depending on component and production-specific conditions, restrictions and deviations may become
necessary. These shall be agreed upon by the responsible development department of Daimler AG,
the materials and process engineering department of the customer plant, and the supplier. The data shall
be documented in the relevant specification documents (e.g. drawing, requirement specifications).
Copyright Daimler AG
6.5
Internal soundness
The following shall apply in addition to the standards listed in Section 6.1:
Macro slags, flakes, porosities, shrinkage cavities and cracks are not permissible.
6.5.1
The obligatory limits of the degree of purity in terms of microscopic inclusions are as follows:
Determination in accordance with DIN 50602:1998-09, method K, sum total index number (oxides).
Table 2: Limits of the degree of purity in terms of inclusions
Diameter d or cross-section
Sum total index number
with identical area
K
[mm]
140 <
d
200
K4 30
100 <
d
140
K4 25
70 <
d
100
K4 25
35 <
d
70
K4 20
17 <
d
35
K3 25
8 <
d
17
K3 20
d
8
K2 25
6.5.2
Depending on the application, e.g. for running gears, a sum total index number as per SEP 1927 can
be required. The determination of the macroscopic degree of purity shall be carried out using ultrasonic
immersion technology as per SEP 1927.
6.6
All steels according to this DBL shall have an austenitic grain size of G = 5 or finer, determined
in accordance with DIN EN ISO 643.
6.7
All steels conforming to this DBL with a lower C content target value of > 0,30 % shall be capable
of induction hardening. This is primarily expressed by the following properties:
Insensitivity to short-term intense heating; i.e. no early coarse-grain growth
Largely segregation free
No grain boundary precipitation
Good austenitization capability, if determined from the melting process
Tests
7.1
Test methods
This section describes the methodology of the tests to be carried out. The tests that shall be applied
in individual cases and the testing frequency are described in Section 7.2.
7.1.1
The chemical composition (unit) analysis shall be carried out using a suitable method as per the state
of the art, e.g. spectral analysis.
Copyright Daimler AG
7.1.2
The hardenability can be determined by suitable calculation according to the set of equations of SEP 1664
applicable in each case. When using other sets of formulas the steel works shall provide evidence
of suitability using the end quench test as per DIN EN ISO 642. In the case of arbitration, the hardenability
test by end quenching in accordance with DIN EN ISO 642 shall be used. Removing samples directly from
the continuous or ingot casting is not permitted.
7.1.3
Series tests as per the state of the art using standardized (ultrasonic testing as per DIN EN 10308 and
DIN EN 10160, ultrasonic immersion testing as per SEP 1927, eddy current tests as per
DIN EN ISO 15549, etc.) or validated methods shall be applied to guarantee there are no defects as listed
in Section 0.
7.1.3.1 Ultrasonic testing as per SEP 1927
The determination of the macroscopic degree of purity can be carried out on the delivery product
(steel bars or semi-finished products) or specifically for batch testing at the start of the melt or on the ingot
casting head. In the event of tests on the delivery product it shall be ensured that these are carried out
in the area with the largest final dimensions. The removal of samples shall be carried out on a minimum
of two different bars.
The materials and process engineering department of the customer plant can require batch testing.
The degree of reduction shall be between 4:1 and 6:1 for batch testing as per SEP 1927.
The following shall apply:
Sum total index number
Sensitivity class
Test volume
Test area
The grain size shall be tested metallographically as per DIN EN ISO 643.
7.2
Test frequency
As per ISO/TS 16949 the supplier is required to monitor and measure the product characteristics to verify
compliance with the product requirements. Proof of the compliance with the acceptance criteria shall
be maintained.
The testing frequency shall be specified on the basis of the risk analysis results (failure mode and effects
analysis, process validation, product validation, continuous improvement process) by suppliers
to guarantee that
product implementation is free of defects.
A minimum specification of the testing frequency by Daimler AG can be defined in specifications
(e.g. drawing entry "Technically free of cracks as per MBN 10456, test severity 100 %").
Copyright Daimler AG
7.3
Test certificates
7.3.1
An inspection certificate 3.1 in accordance with DIN EN 10204 shall be provided for each batch, or each
delivery in case of different delivery states.
The inspection certificate shall contain the following data and test results in addition to the standard
requirements as per DIN EN 10168:
Any additional indications of inspection results shall be agreed between the supplier and the customer
plant.
The retention time at the supplier shall be a minimum of 15 years from the creation date.
Submission of the test report to the customer plant is necessary only on request.
7.3.2
The written test report in accordance with SEP 1927 shall be enclosed, containing the following minimum
information:
Name of the steel manufacturer
Number of batch tested
Scope of testing: tested areas and applied sensitivity class
Track width
Size of the "dead zone"
Production level according to which the ultrasonic test was completed
Degree of reduction and test specimen dimensions
Test facilities used (scanner, computer, ultrasound device, test head)
Test results
Name and signature of the inspector
Copyright Daimler AG
Annex A (normative)
Material specification 39MnCrB6-2 mod.
(formerly 30MnB5+DBL 4552)
Chemical analysis
Table 3: A-1 / Chemical analysis of 39MnCrB6-2 mod.
Element [% by mass]
Product version
.00
C
0,30 0,40
Si
0,15 0,50
Mn
1,20 1,80
P
0,035
S
0,025 0,045 *
Cr
0,30 0,50
Mo
0,10
Ni
0,25
Cu
0,25
Al
0,020 0,060
Sn
0,030
Cu + 10xSn
0,50
Ti
0,010 0,040
V
0,13
Nb
0,008
B
0,0010 0,0040
Sb
0,005
As
0,05
Pb
0,10
*) For component parts on which Daimler does not carry out additional machining, the specification
of the minimum sulfur content, i.e. S 0,035 %, shall not apply.
The specifications as per DIN EN 10083-3 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 3.
Copyright Daimler AG
Annex B (normative)
Material specification 34MnCrMo6-4
Chemical analysis
Table 4: B-1 / Chemical analysis of 34MnCrMo6-4
Element [% by mass]
Product version
.00
C
0,32 0,36
Si
0,40
Mn
1,50 1,80
0,035
0,025 0,040 *
Cr
0,95 1,20
Mo
0,30 0,40
Ni
0,25
Cu
0,25
Al
0,010 0,050
Sn
0,030
Cu + 10xSn
0,50
Ti
0,005
0,009
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
*) For component parts on which Daimler does not carry out additional machining, the specification
of the minimum sulfur content, i.e. S 0,035 %, shall not apply.
The specifications as per DIN EN 10083-3 shall apply to the limit deviations of the unit analysis from
the limits valid for melt analysis as per Table 4.
Hardenability
The hardenability shall be coordinated with the materials and process engineering department
of the customer plant.
Copyright Daimler AG
Annex C (normative)
Material specification C45E
(formerly: Ck45)
Chemical analysis
Table 5: C-1 / Chemical analysis of C45E
Element
Product version
[% by mass]
.00
C
0,42 0,50
Si
0,40
Mn
0,50 0,80
0,030
0,020 0,040 *
Cr
0,10 0,20
Mo
0,07
Ni
0,25
Cu
0,25
Al
0,010 0,050
Sn
0,030
Cu + 10xSn
0,50
Ti
0,005
0,009
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
*) For component parts on which Daimler does not carry out additional machining, the specification
of the minimum sulfur content, i.e. S 0,035 %, shall not apply.
The specifications as per DIN EN 10083-2 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 5.
Copyright Daimler AG
Annex D (normative)
Material specification 38MnS6
Chemical analysis
Table 6: D-1 / Chemical analysis of 38MnS6
Element [% by mass]
Product version
.00
C
0,36 0,40
Si
0,20 0,65
Mn
1,30 1,60
0,035
0,045 0,065
Cr
0,10 0,20
Mo
0,07
Ni
0,25
Cu
0,25
Al
0,010 0,050
Sn
0,030
Cu + 10xSn
0,50
Ti
0,005 *
0,009 *
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
*) Additions of Ti and V by alloying shall be agreed upon with the customer plant as part of the supply
of samples.
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis from
the limits valid for melt analysis as per Table 6.
Copyright Daimler AG
Annex E (normative)
Material specification 35MnS4
(formerly: C35 mod.)
Chemical analysis
Table 7: E-1 / Chemical analysis of 35MnS4
Element [% by mass]
Product version
.00
C
0,32 0,39
Si
0,40 0,80
Mn
0,80 1,00
0,035
0,045 0,065
Cr
0,10 0,20
Mo
0,10
Ni
0,25
Cu
0,25
Al
0,010 0,050
Sn
0,030
Cu + 10xSn
0,50
Ti
0,005
0,009
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 7.
Copyright Daimler AG
Annex F (normative)
Material specification C70S6
Chemical analysis
Table 8: F-1 / Chemical analysis of C70S6
Element [% by mass]
Product version
.00
C
0,68 0,73
Si
0,15 0,25
Mn
0,50 0,55
0,035
0,050 0,070
Cr
0,10 0,20
Mo
0,10
Ni
0,25
Cu
0,25
Al
0,030
Sn
0,030
Cu + 10xSn
0,50
0,0120 0,0160
Ti
0,012
0,03 0,05
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 8.
Copyright Daimler AG
Annex G (normative)
Material specification for AFP steels
Note: DIN EN 10267 shall apply to ready-to-install parts made of AFP steels.
Chemical analysis
Table 9: G-1 / Chemical analysis of AFP steels subject to P treatment at the Daimler AG plants
Element
19MnVS6
30MnVS6
38MnVS6
46MnVS6
46MnVS3
[% by mass]
1.1301
1.1302
1.1303
1.1304
1.1305
Product version
.00
.00
.00
.00
.00
0,15 0,22
0,27 0,33
0,36 0,40
0,42 0,47
0,45 0,50
Si
0,50 0,70
0,50 0,70
0,50 0,70
0,50 0,80
0,50 0,70
Mn
1,20 1,60
1,40 1,60
1,30 1,60
1,30 1,60
0,70 1,00
0,035
0,035
0,035
0,035
0,035
0,020 0,060
0,030 0,060
0,045 0,060
0,020 0,035
0,045 0,065
Cr
0,10 0,20
0,10 0,20
0,10 0,20
0,10 0,20
0,10 0,20
Mo
0,07
0,07
0,07
0,07
0,07
Ni
0,25
0,25
0,25
0,25
0,25
Cu
0,25
0,25
0,25
0,25
0,25
Al
0,010 0,050
0,010 0,050
0,010 0,050
0,010 0,050
0,010 0,050
Sn
0,030
0,030
0,030
0,030
0,030
Cu + 10xSn
0,50
0,50
0,50
0,50
0,50
0,012 0,020
0,012 0,020
0,012 0,020
0,012 0,020
0,012 0,020
Ti
0,08 0,13
0,08 0,13
0,08 0,13
0,10 0,15
0,08 0,13
Nb
0,008
0,008
0,008
0,008
0,008
0,0005
0,0005
0,0005
0,0005
0,0005
Sb
0,005
0,005
0,005
0,005
0,005
As
0,05
0,05
0,05
0,05
0,05
Pb
0,10
0,10
0,10
0,10
0,10
*) Titanium shall only be added following agreement and approval by the materials and process
engineering department of the customer plant. In any other case, the following applies: Ti 0,005 %.
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 9.
Copyright Daimler AG
Annex H (normative)
Material specification 30MnVS6+Ti
Chemical analysis
Table 10: H-1 / Chemical analysis of 30MnVS6+Ti
Element [% by mass]
Product version
.00
C
0,27 0,33
Si
0,50 0,70
Mn
1,40 1,60
0,025
0,030 0,060
Cr
0,10 0,25
Mo
0,07
Ni
0,25
Cu
0,25
Al
0,010 0,050
Sn
0,030
Cu + 10xSn
0,50
0,012 0,020
Ti
0,015 0,035
0,08 0,13
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 10.
Copyright Daimler AG
Annex I (normative)
Material specification 36MnVS4
Chemical analysis
Table 11: I-1 / Chemical analysis of 36MnVS4
Element [% by mass]
Product version
.00
C
0,34 0,38
Si
0,60 0,75
Mn
0,95 1,05
0,045
0,065 0,085
Cr
0,25
Mo
0,06
Ni
0,20
Cu
0,25
Al
0,030
Sn
0,030
Cu +10xSn
0,50
0,015 0,020
Ti
0,005
0,25 0,35
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 11.
Copyright Daimler AG
Annex J (normative)
Material specification 35MnVS4-3
(formerly: 38MnVS6mod)
Chemical analysis
Table 12: J-1 / Chemical analysis of 35MnVS4-3
Element [% by mass]
Product version
.00
C
0,33 0,37
Si
0,50 0,65
Mn
1,00 1,15
< 0,025
0,015 0,030
Cr
0,10 0,20
Mo
0,02 0,07
Ni
0,20
Cu
0,20
Al
0,010 0,025
Sn
0,030
Cu + 10xSn
0,50
0,015 0,020
Ti
< 0,025
0,25 0,35
Nb
0,008
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 12.
Copyright Daimler AG
Annex K (normative)
Material specification 46MnVNbS5
(formerly: 46MnVS6mod)
Chemical analysis
Table 13: K-1 / Chemical analysis of 46MnVNbS5
Element [% by mass]
Product version
.00
C
0,44 0,48
Si
0,40 0,70
Mn
1,00 1,200
0,025
0,055 0,070
Cr
0,30
Mo
0,08
Ni
0,20
Cu
0,25
Al
0,030
Sn
0,030
Cu + 10xSn
0,50
0,0150 0,0220
Ti
0,005
0,10 0,18
Nb
0,020 0,045
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 13.
Copyright Daimler AG
Annex L (normative)
Material specification 70MnVS4
Chemical analysis
Table 14: L-1 / Chemical analysis of 70MnVS4
Element [% by mass]
Product version
.00
C
0,68 0,73
Si
0,15 0,25
Mn
0,80 1,00
0,035
0,050 0,070
Cr
0,10 0,20
Mo
0,05
Ni
0,25
Cu
0,25
Al
0,030
Sn
0,030
Cu + 10xSn
0,50
0,0120 0,0200
Ti
0,005
0,10 0,22
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10267 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 14.
Copyright Daimler AG
Annex M (normative)
Material specification 71MnVS4
Chemical analysis
Table 15: M-1 / Chemical analysis of 71MnVS4
Element [% by mass]
Product version
.00
C
0,69 0,73
Si
0,20 0,30
Mn
0,90 1,00
0,025
0,055 0,065
Cr
0,15 0,25
Mo
0,05
Ni
0,20 0,30
Cu
0,25
Al
0,020 0,030
Sn
0,025
Cu + 10xSn
0,50
0,012 0,020
Ti
0,005
0,22 0,26
Nb
0,008
0,0005
Sb
0,005
As
0,05
Pb
0,10
Copyright Daimler AG
Annex N (normative)
Material specification 12CrMnMoV7-5
Chemical analysis
Table 16: N-1 / Chemical analysis of 12CrMnMoV7-5
Element [% by mass]
Product version
.00
C
0,10 0,15
Si
0,15 0,30
Mn
1,10 1,40
0,015
0,015
Cr
1,60 1,80
Mo
0,10 0,20
Ni
0,23 0,35
Cu
0,25
Al
0,020 0,030
Sn
0,030
Cu + 10xSn
0,50
0,014 0,022
Ti
0,005
0,05 0,14
Nb
0,020 0,030
0,0005
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10083-3 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 16.
Copyright Daimler AG
Annex O (normative)
Material specification 19MnB4 mod.
Chemical analysis
Table 17: O-1 / Chemical analysis of 19MnB4 mod.
Element [% by mass]
Product version
.00
C
0,16 0,19
Si
0,60 0,90
Mn
1,60 1,90
0,015
0,015
Cr
1,00 1,30
Mo
0,02 0,10
Ni
0,25 0,50
Cu
0,10
Al
0,005 0,020
Sn
0,030
Cu + 10*Sn
0,50
Ti
0,050
0,050
Nb
0,008
0,0015 0,0050
Sb
0,005
As
0,05
Pb
0,10
The specifications as per DIN EN 10083-3 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 17.
Copyright Daimler AG
Annex P (informative)
Material specification Cf53 (NFN)
(Replacement for new designs: C50E or C55E DIN EN 10083)
Chemical analysis
Table 18: P-1 / Chemical analysis of Cf53
Element [% by
Product version
mass]
.00
0,50 0,57
0,49 0,53
Si
0,15 0,35
0,15 0,40
Mn
0,40 0,75
0,40 0,50
0,025
0,025
0,020 - 0,040 *
0,020 0,040 *
Cr
0,10 0,20
0,10 0,15
Mo
0,07
0,07
Ni
0,25
0,25
Cu
0,25
0,25
Al
0,010 0,050
0,010 0,050
Sn
0,030
0,030
Cu + 10xSn
0,50
0,50
Ti
0,005
0,005
0,009
0,009
Nb
0,008
0,008
0,0005
0,0005
Sb
0,005
0,005
As
0,05
0,05
Pb
0,10
0,10
*) For component parts on which Daimler does not carry out additional machining, the specification
of the minimum sulfur content, i.e. S 0,035 %, shall not apply.
The specifications as per DIN EN 10083-3 shall apply to the limit deviations of the unit analysis
from the limits valid for melt analysis as per Table 18.
Copyright Daimler AG
Annex Q (informative)
Materials not for new designs (NFN)
Recoding of old (NFN) to new material designations
Table 19: Q-1 / Recoding of old (NFN) to new material designations
Old designation/NFN
New designation
30Mn5
30Mn5+DBL 4552
C35 mod.
n/a
Cf53
38MnVS5
38MnVS6 mod.
46MnVS6
46MnVS6 mod.
Copyright Daimler AG