Professional Documents
Culture Documents
3-007
DIVISION
Engineering Specification
Custom Process System (CPS)
Title:
Revision: 01
Date:
Page:
1 of 45
Prepared by:
Reviewed by:
Approved by:
Steven Roberts
Oleg Barsky
Greg Dodson
01
00
Revised as noted
Initial release
SR
SR
SB
OB
GD
GD
Rev.
Date
Description
By
Checked
Approved
CPS-03-7.3-007
DIVISION
Engineering Specification
Custom Process System (CPS)
Title:
Revision: 01
Date:
Page:
2 of 45
Prepared by:
Reviewed by:
Approved by:
Steven Roberts
Oleg Barsky
Greg Dodson
List of Revisions
Revision
01
01
01
Page
2
Section 3
Line Classes
A
Section 3
Line Classes
B and D
01
A01
01
01
A01N
A02
01
A02N
01
A03
01
01
A03N
A04
01
A04N
01
A06
01
A06N
01
A08
01
A08N
01
B01
01
B02
01
B02N
01
B03
01
B03N
01
B04
Description of Change
Add Page for List of Revisions
Change corrosion allowance for Class A02 to None (was 1/16 / 1.6mm)
Change corrosion allowance for Class A02N to None (was 1/8 / 3.2mm)
Add Piping Class A02CR Cryogenic Service
Change corrosion allowance for Class B02 to None (was 1/16 / 1.6mm)
Change corrosion allowance for Class B02N to None (was 1/8 / 3.2mm)
Add Piping ClassB02CR Cryogenic Service
Updated A01, A01N, B01, B02, B02N, B03, B03N, B04, B04N, B06, B06N, B08, B08N
Change corrosion allowance for Class D02 to None (was 1/16 / 1.6mm)
Change corrosion allowance for Class D02N to None (was 1/8 / 3.2mm)
Add Piping Class D02CR Cryogenic Service
Updated D02, D02N, D03, D03N, D04, D04N, D06, D06N, D08, D08N
Revise pipe schedule from Sch 40 to Sch 80 on sizes to 3
Changes Nipples and Swages from Sch 80 to Sch 160 and Swage from Sch 40 to Sch 80
Revised Gasket on RF Flanged to 1/16 Compressed Fiber from Spiral Wound
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revise pipe schedules from Sch 40 to Sch 80 sizes to 3
Revise Nipples and Swages from Sch 80 to Sch 160, and from Sch 40 to Sch 80
Revise pipe schedule on 3 from Sch 40 to Sch 80
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revise pipe schedule from Sch 40 to Sch 80 on sizes up to 3
Revise Swage (PE) from Sch 40 to Sch 80
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revise pipe schedule from Sch 40 to Sch 80 sizes to 1-1/2
Revise Swage (PE) from Sch 40 to Sch 80
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revise pipe schedule from Sch 40 to Sch 80 sizes to 1-1/2
Revise Swage (PE) from Sch 40 to Sch 80
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
CPS-03-7.3-007
DIVISION
Engineering Specification
Custom Process System (CPS)
Title:
Revision: 01
Date:
Page:
3 of 45
Prepared by:
Reviewed by:
Approved by:
Steven Roberts
Oleg Barsky
Greg Dodson
Revision
01
Page
B04N
01
B06
01
B06N
01
B08
01
B08N
01
D02
01
D02N
01
01
01
D03
D03N
D04
01
D04N
01
D06
01
D06N
01
D08
01
D08N
Description of Change
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 & 3
Revise Nipples and Swages from 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 thru 8
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 thru 8
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 thru 8
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sized to 1-1/2 and from 10S to 40S for 2 thru 8
Revise Nipples and Swages from 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 from - to Sch
80 sizes 10 thru 24
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 from - to Sch
80 sizes 10 thru 24
Revise Nipples and Swages from Sch 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 from - to Sch
80 sizes 10 thru 24
Revise Nipples and Swages from Sch 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 from - to Sch
80 sizes 10 thru 24
Revise Nipples and Swages from Sch 10S and 40S to 80S
Revise Temp / Pressure Chart to from -20F to -50F (-29C to -46C)
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 from - to Sch
80 sizes 16 thru 24
Revise Swage PE from Sch 10S to 80S
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 from - to Sch
80 sizes 20 and 24
Revise Swage PE from Sch 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 to 4 from to Sch 80 sizes 10 thru 24
Revise Nipples and Swages from Sch 10S and 40S to 80S
Revised pipe schedules from 10S to 80S sizes to 1-1/2 from 10S to 80S size 2 to 4 from to Sch 80 sizes 10 thru 24
Revise Nipples and Swages from Sch 10S and 40S to 80S
CPS-03-7.3-007
DIVISION
Engineering Specification
Custom Process System (CPS)
Title:
Revision: 01
Date:
Page:
4 of 45
Prepared by:
Reviewed by:
Approved by:
Steven Roberts
Oleg Barsky
Greg Dodson
1.0
SCOPE
The purpose of this specification is to establish standard piping classes to determine the
materials, schedules, valves, bolting, and construction for piping that is in full conformance with
B31.3 Process Piping. This specification is to be used when we are designing to Cameron
standard, and when a client does not furnish the proper client specifications.
2.0
3.0
Line
Class
Rev
Date
Rating / Material
Corrosion
Allowance
Service
A01
A01N
1
1
5-MAR-2014
5-MAR-2014
1/16(1.8mm)
1/8 (3.2mm)
A02
A02N
1
1
5-MAR-2014
5-MAR-2014
None
None
A02CR
A03
A03N
0
1
1
5-MAR-2014
5-MAR-2014
5-MAR-2014
A04
A04N
1
1
5-MAR-2014
5-MAR-2014
A06
A06N
1
1
A08
A08N
1
1
General Process
General Process
Sour Service
General Process
General Process
Sour Service
Cryogenic Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
None
1/16(1.8mm)
1/8 (3.2mm)
None
None
5-MAR-2014
5-MAR-2014
5-MAR-2014
5-MAR-2014
None
None
None
None
CPS-03-7.3-007
DIVISION
Engineering Specification
Custom Process System (CPS)
Title:
Revision: 01
Date:
Page:
5 of 45
Prepared by:
Reviewed by:
Approved by:
Steven Roberts
Oleg Barsky
Greg Dodson
Line
Class
Rev
Date
Rating / Material
Corrosion
Allowance
Service
B01
B01N
1
0
5-MAR-2014
20-DEC-2013
1/16(1.8mm)
1/8 (3.2mm)
B02
B02N
1
1
5-MAR-2014
5-MAR-2014
None
None
B02CR
B03
B03N
0
1
1
5-MAR-2014
5-MAR-2014
5-MAR-2014
B04
B04N
1
1
5-MAR-2014
5-MAR-2014
B06
B06N
1
1
B08
B08N
General Process
General Process
Sour Service
General Process
General Process
Sour Service
Cryogenic Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
None
1/16(1.8mm)
1/8 (3.2mm)
None
None
5-MAR-2014
5-MAR-2014
1
1
5-MAR-2014
5-MAR-2014
None
None
D01
D01N
0
0
20-DEC-2013
20-DEC-2013
1/16(1.8mm)
1/8 (3.2mm)
D02
D02N
1
1
5-MAR-2014
5-MAR-2014
None
None
D02CR
D03
D03N
0
1
1
5-MAR-2014
5-MAR-2014
5-MAR-2014
D04
D04N
1
1
5-MAR-2014
5-MAR-2014
D06
D06N
1
1
D08
D08N
1
1
None
None
None
1/16(1.8mm)
1/8 (3.2mm)
None
None
5-MAR-2014
5-MAR-2014
5-MAR-2014
5-MAR-2014
None
None
None
None
General Process
General Process
Sour Service
General Process
General Process
Sour Service
Cryogenic Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
General Process
General Process
Sour Service
Specification
A01
Document No
Date
19-Dec-2013
Revis ion
0
1
Description
Cameron Standard - Issued for Design
5-Mar-2014
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotes t
Pres sure
ASME B31.3
-20F / +600F
-29C / 316C
0.0625" (1.6mm)
428 psig
29.5 barg
1/2"
3/4"
1"
Sch
Pipe
6"
8"
10"
12"
14"
16"
18"
20"
24"
STD
ASTM A-105
Seamless , ASTM A-234 WPB, Butt Weld, Bore to match pipe (Note 3)
Couplings
Nipples (thd x thd)
Sockolets
Threadolets
Weldolets
Bolting
VALVES
4"
GD
GD
Service
Sch 40
150# RF SW (Note 2)
(Notes 4, 5)
3"
OB
SB
Plugs (Note 6)
Gaskets
2"
Ends
Matl
Sch
Flanges Rating
Matl
Fittings
Unions
1-1/2"
Sch 80
SR
SR
Rating
Pipe Size
Gate
A1R
Ball
A2R, A2RF
Globe
A4R
Check
Butterfly
Needle /
G6S-S, G9S-S
Gauge
Notes : 1. -20 / 100F pres sure rating is used to determine the required pipe wall thicknes s.
2. Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
3. Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4. Carbon steel body valves may be A-105 forged s teel or A-216-WCB cas tings.
5. Valves with elas tomer s eats and/or seals may not be rated for full ANSI press ure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for s ys tem upper limit des ign temperature.
6. Items may be cad plated, zinc plated, or galvanized
7. Welded construction to be used for in-line process piping. Threaded connections and fittings are permitted
for instrument take-offs, piping vent and drain valves
8 Pipe material may be A106 Gr B seamless , API-5L Gr B s eamles s or A53B seamless
Temp F
-20 to 100
200
300
400
500
600
650
700
750
800
PSIG
285
260
230
200
170
140
125
110
95
80
Temp C
-29 to 38
50
100
150
200
250
300
325
350
375
400
425
BAR
19.6
19.2
17.7
15.8
13.8
12.1
10.2
9.3
8.4
7.4
6.5
5.5
1 1/2
3/4
1/2
SWT
SWTS
SWTS
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
20
18
16
24
24
WT
20
18
16
14
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
12
10
8
WRT
WOL
WOL
WRT
WRT
WOL
WRT
WRT
WOL
WRT
WRT
WRT
6
4
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
1 1/2
1
3/4
1/2
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
12
10
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
14
SOL
TOL
WRT
WRT
WOL
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
Sockolet
Threadolet
WOL
WRT
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WT
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
Weldolet
Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
Specification
A01N
Document No
Rating
Piping Code
ASME B31.3
1/2"
Date
19-Dec-2013
5-Mar-2014
Temp Range
-20F / +600F
-29C / 316C
3/4"
1"
1-1/2"
Sch 160
Plain End (PE)
Seam less, ASTM A-333-6
2"
Sch 80
3"
Description
Cameron Standard - Issued for Des ign
Material / Group
4"
SR
Service
0.125" (3.2mm )
428 psig
29.5 barg
6"
Sch 40
8"
10"
12"
14"
16"
18"
Sch STD
ASTM A-105
Seam less, ASTM A-234 WPB, Butt Weld, Bore to match pipe (Note 3)
Plugs (Note 6)
Couplings
Nipples (thd x thd)
Nipples (PE x thd)
Sch160, Seamless
A-333-6 or A-420-WPL6 (note 8)
Sockolets
Threadolets
Weldolets
20"
24"
GD
Hydrotest
Pressure
SB
Corrosion
Allowance
150# RF SW (Note 2)
Unions
Gaskets
Revision
0
VALVES
Bolting
G6S-SN, G9S-SN
Notes : 1 -20 / 100F pressure rating is used to determ ine the required pipe wall thickness.
2 Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Carbon steel body valves m ay be A-105 forged steel or A-216-WCB castings.
5 Valves with elastomer seats and/or seals m ay not be rated for full ANSI press ure-tem perature values.
Refer to P&ID's and/or Equipm ent Data Sheets for system upper limit design tem perature.
6 Items m ay be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line process piping. Threaded connections are perm itted for
instrum ent take-offs, piping vent and drain valves
8 Pipe material may be A106 Gr B seamles s, API-5L Gr B s eamless or A53B seamless
Temp F
-20 to 100
200
300
400
500
600
650
700
750
800
PSIG
285
260
230
200
170
140
125
110
95
80
Temp C
-29 to 38
50
100
150
200
250
300
325
350
375
400
425
BAR
19.6
19.2
17.7
15.8
13.8
12.1
10.2
9.3
8.4
7.4
6.5
5.5
1 1/2
3/4
1/2
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
8
6
4
3
2
1 1/2
1
3/4
1/2
24
WT
WRT
WRT
WRT
20
18
16
WT
WRT
WRT
WT
WRT
WT
14
12
10
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WRT
WRT
WT
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
A02
Document No
Revision
Date
Description
0
1
12-Dec-2013
5-Mar-2014
Prepared Checked
SR
SR
Approved
OB
SB
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-50F / +600F
-46C / 316C
NONE
413 psig
28.5 barg
Pipe Size
1/2"
Sch
Pipe
3/4"
1"
Sch 80S
1-1/2"
2"
3"
Sch 40S
4"
6"
8"
10"
Ends
Matl
12"
16"
18"
20"
24"
Sch
Flanges Rating
14"
Sch 10S
GD
GD
150# RF SW (note 2)
ASTM A-182-F304
Matl
Fittings
Unions
Plugs
Couplings
3000# FS, Full, Threaded A-182-F304
Nipples (thd x thd) Sch 80S Seamless A-312-TP304/304L
Nipples (PE x thd) Sch 80S Seamless, A-312-TP304/304L
Swages (thd x thd) Sch 80S Seamless A312-TP304/304L
Swages (PE x thd)
Swages (PE x PE)
Sockolets
Threadolets
Weldolets
Gaskets
VALVES
Bolting (Note 5)
Gate (4)
D1Z-S, D1S-S
A1R-S
Ball (4,5)
A2R-S, A2RF-S
A4R-S
A5R-S, A5RG-S, A5RW-S
A7RG-S, A7RW-S
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will be provided to indicate where internal beveling is required
PSIG
Temp C
BAR
-50 to 100
200
275
230
-46 to 38
50
19
18.3
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 304/304L
or may be certified for 304 with chemistry that meets 304L
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values
Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
300
205
100
15.7
400
190
150
14.2
500
600
170
140
200
250
13.2
12.1
650
125
300
10.2
700
110
325
9.3
750
800
95
80
350
375
8.4
7.4
400
6.5
425
5.5
3/4
1/2
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
20
WT
WRT
WT
18
WRT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
10
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
4
3
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
1 1/2
WT
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT
A02N
Document No
Revision
0
1
Rating
ASME CLASS 150
Pipe Size
Pipe
ASME B31.3
-50F / +600F
-46C / 316C
1/2"
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
Couplings
Nipples (thd x thd)
Nipples (PE x thd)
Swages (thd x thd)
Swages (PE x thd)
Swages (PE x PE)
Sockolets
Threadolets
Weldolets
VALVES
Service
NONE
413 psig
28.5 barg
6"
8"
10"
12"
14"
Sch 10S
Beveled End (BE)
16"
18"
20"
24"
A4R-SN
A5R-SN, A5RG-SN, A5RW-SN
A7RG-SN, A7RW-SN
Needle /
Gauge
Hydrotest
Pressure
ASTM A-182-F304
Plugs
Ball (4,5)
4"
Corrosion
Allowance
150# RF SW (note 2)
Unions
Gate (4)
2"
3"
Sch 40S
Bolting (Note 5)
19-Dec-2013
5-Mar-2014
Temp Range
Flanges Rating
Matl
Gaskets
Description
Material / Group
Ends
Matl
Sch
Fittings
Date
Piping Code
Sch
Specification
G6S-SN, G9S-SN
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will be provided to indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 304/304L
Temp F
-50 to 100
200
300
400
500
600
650
PSIG
275
230
205
190
170
140
125
Temp C
-46 to 38
50
100
150
200
250
300
BAR
19
18.3
15.7
14.2
13.2
12.1
10.2
700
110
325
9.3
750
800
95
80
350
375
400
8.4
7.4
6.5
425
5.5
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
WT
20
24
18
16
14
12
10
20
18
WRT
WRT
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
8
WRT
WOL
WOL
WRT
WRT
WOL
WRT
WRT
WOL
WRT
WRT
WRT
6
4
3
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WRT
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
1 1/2
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
SWT Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWTS
WT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
A02CR
Document No
Rating
ANSI 150LB
Pipe Size
Pipe
Date
5-Mar-2014
Description
Cameron Standard - Issued for Design
Prepared
Checked
Approved
SB
TW
GD
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-175F / +600F
None
413 psig
1/2"
Sch
Ends
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
2"
3"
Sch 40S
4"
6"
8"
Matl
Sch
Flanges Rating
Matl
Fittings
Rev No
16"
18"
20"
24"
Sch 10
ASTM A-182-F304
Seamless, ASTM A-403-WP304, Butt Weld, Bore to match pipe (Note 3)
Plugs
12"
14"
Sch 10S
Beveled End (BE)
150# RF SW
Unions
10"
Couplings
3000# FS, Full, Threaded, A-182-F304
Nipples (thd x thd)
Sch 80S smls A-312-TP304
Nipples (PE x thd)
O-Lets
Threadolets
Weldolets
Gaskets
Bolting
Gate
Globe
D2Z-SCR, D2ZF-SCR
D4Z-SCR
A2R-SCR, A2RF-SCR
A4R-SCR
Check
A5R-SCR, A5RW-SCR
A7R-SCR
Ball (5)
Valves
B utterfly (5)
Needle
G6S-SCR, G9S-SCR
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Threaded connections are not permitted beneath insulation. Seal welding is premitted.
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
Temp F
PSIG
Temp C
BAR
-175 to 100
200
275
230
-115 to 38
50
19
18.3
300
400
500
205
190
170
100
150
200
15.7
14.2
13.2
600
650
140
125
250
300
12.1
10.2
700
750
110
95
325
350
9.3
8.4
800
80
375
400
7.4
6.5
425
5.5
3/4
1/2
4 Materials may be specified and purchased as grade 304L, or dual certified 304 / 304L
Grade 316 or 316/316L may be substituted for Grade 304 or 304/304L
5 Standard valves having elastomer seats are typically rated for 250 psig maximum temperature. Valves with
elastomer seals may not be rated for full ANSI pressure-temperature values. Refer to P&ID's and/or
equipment data sheets for system design pressure and upper limit design temperature. High temperature
ball and butterfly valves will be required to be metal seated.
6 Valves are suitable for Cryogenic temperature service to -175F
7 Welded construction to be used for in-line process piping through the first instrument isolation valve.
Threaded connection are permitted only for connections to instruments outside of insulation
BRANCH SIZE
HEADER SIZE
24
WT
20
24
20
18
WRT
WRT
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
8
6
4
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
1 1/2
1
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
3/4
1/2
SOL
SOL
SWTS
SWT
18
16
SOL
SOL
SOL
SOL
SOL
SOL
Full size SW Tee with Swage
Socket Weld Tee
14
12
10
1 1/2
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SWT
SWTS
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
Sockolet (or other O-Let)
SOL
SOL
WOL
SOL
SOL
Weldolet
SOL
SOL
SWTS
SWTS
TOL
WRT
SWT
SWTS
SWTS
WT
SWT
SWTS
SWT
Butt Weld Tee
Specification
A03
Document No
Revis ion
0
1
Date
19-Dec-2013
Des cription
Cam eron Standard - Iss ued for Design
5-Mar-2014
Rating
Piping Code
Material / Group
Tem p Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-50F / +600F
-46C / 316C
0.0625"
428 psig
29.5 barg
Pipe Size
1/2"
3/4"
1"
Sch
Pipe
1-1/2"
Sch 80
2"
3"
4"
12"
GD
16"
18"
Sch STD
20"
24"
150# RF SW
150# RFWN
ASTM A-350-LF2, Cl. 1
Plugs (Note 6)
Couplings
Sch 80 Seamless
A-333-6 or A-420-WPL6
Sockolets
Threadolets
Weldolets
Bolting
Gate (4)
VALVES
10"
SB
Unions
Gaskets
8"
SR
Service
Sch 40
Matl
Sch
Flanges Rating
Matl
Fittings
6"
Ends
A1R-L
A2R-L, A2RF-L
B utterfly (5)
A4R-L
A5R-L, A5RG-L, A5RW-L
A7RG-L, A7RW-L
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 -50 / 100F pressure rating is used to determ ine the required pipe wall thickness.
2 Use FF flange for connection to FF cas t iron or ductile iron flanges for equipm ent
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Temp F
PSIG
Temp C
BAR
-50 to 100
200
300
400
285
260
230
200
-46 to 38
50
100
150
19.6
19.2
17.7
15.8
500
170
200
13.8
600
650
700
750
140
125
110
95
250
300
325
350
12.1
10.2
9.3
8.4
800
80
375
400
425
7.4
6.5
5.5
1 1/2
3/4
1/2
SWT
SWTS
SWTS
SWTS
SWT
SWTS
SWTS
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
20
18
24
WT
WRT
WRT
WT
WRT
WT
16
14
12
10
8
WRT
WRT
WRT
WOL
WOL
WRT
WRT
WRT
WRT
WOL
6
4
3
2
WOL
WOL
WOL
WOL
1 1/2
1
3/4
1/2
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
20
18
16
14
12
10
WRT
WRT
WRT
WRT
WOL
WT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL
TOL
WRT
WRT
WOL
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
Sockolet
Threadolet
WOL
WRT
Weldolet
Butt Weld Reducing Tee
WT
PIPING SPECIFICATION - ASME CLASS 150, Low Temperature Carbon Steel (NACE)
A03N
Document No
Date
19-Dec-2013
5-Mar-2014
Revision
Description
Cameron Standard - Issued for Design
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-50F / +600F
-46C / 316C
0.125" (3.2mm)
428 psig
29.5 barg
Pipe
1/2"
3/4"
1"
Sch 160
Sch
Ends
1-1/2"
2"
3"
4"
Plugs (Note 6)
16"
18"
Sch STD
20"
24"
Sockolets
Threadolets
VALVES
150# RFWN
B utterfly (5)
Needle /
Gauge
GD
Gate (4)
12"
GD
SB
Bolting
10"
OB
SR
Gaskets
8"
SR
Service
Sch 40
Couplings
Nipples (thd x thd)
Weldolets
6"
Sch 80
Matl
Sch
Flanges Rating
Matl
Fittings
Unions
Rating
Pipe Size
Specification
A2RLN, A2RF-LN
A4R-LN
A5R-LN, A5RG-LN, A5RW-LN
A7RG-LN, A7RW-LN
G6S-SN, G9S-SN
Notes: 1 -50 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Temp F
PSIG
Temp C
BAR
-50 to 100
200
300
285
260
230
-46 to 38
50
100
19.6
19.2
17.7
400
200
150
15.8
500
600
650
700
750
170
140
125
110
95
200
250
300
325
350
13.8
12.1
10.2
9.3
8.4
800
80
375
400
425
7.4
6.5
5.5
1 1/2
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
20
18
16
14
24
24
WT
12
20
18
16
14
12
WRT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
10
8
6
4
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WRT
WRT
WOL
WOL
WRT
WRT
WRT
WOL
10
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
3
2
1 1/2
1
3/4
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
SWT Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
A04
Document No
Rating
ASME CLASS 150
Pipe Size
Revision
Date
0
1
20-Dec-2013
Description
5-Mar-2014
Piping Code
Material / Group
Temp Range
ASME B31.3
-20F / +600F
-29C / 316C
1/2"
Sch
Pipe
Ends
Matl
Sch
Flanges Rating
Matl
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
2"
3"
Sch. 40S
4"
SR
Revise Pipe Sch, Nipples, Swages, Temp / Pressure Rating chartSR
OB
SB
GD
GD
Corrosion
Allowance
Hydrotest
Pressure
Service
NONE
413 psig
28.5 barg
6"
8"
10"
14"
16"
18"
20"
Sch 10S
Beveled End (BE)
ASTM A312-Grade 316/316L ERW (note 8)
ASTM A-312-TP316/316L
12"
24"
150# RF SW (note 2)
ASTM A-182-F316/316L
Fittings
Unions
Plugs
6000# FS, Hex Head, Thd, A-182-F316
Couplings
3000# FS, Full, Threaded A-182-F316
Nipples (thd x thd)
Sch 80S Smls A-312-TP316
Nipples (PE x thd)
Sch 80S Smls A-312-TP316/316L
Swages (thd x thd)
Sch 80S Smls A-403-WP316
Swages (PE x thd) Sch 80S Smls A-403-WP316/316L
Sockolets
3000# FS, A-182-F316/316L
Threadolets
3000# FS, A-182-F316/316L
Weldolets
Gaskets
(RF Flanges) 1/16 thk, ANSI B16.21, Synthetic Compressed Fiber with Nitrile Binder, Klinger C4401 or equivalent
(FF Flanges) 1/16 thk, ANSI B16.21, Full-Faced, Synthetic Compressed Fiber with Nitrile Binder, Klinger C4401 or equivalent
Bolts / Cap Screws, Alloy Steel, A-193-B8
Bolting (Note 5)
Gate (4)
A2R-S, A2RF-S
VALVES
Ball (4,5)
A4R-S
A5R-S, A5RG-S, A5RW-S
A7RG-S, A7RW-S
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will be provided to indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 316/316L
Temp F
PSIG
Temp C
BAR
-20 to 100
200
300
400
500
600
650
700
750
275
235
215
195
170
140
125
110
95
-29 to 38
50
100
150
200
250
300
325
350
19
18.4
16.2
14.8
13.7
12.1
10.2
9.3
8.4
800
80
375
400
425
7.4
6.5
5.5
1 1/2
3/4
1/2
BRANCH SIZE
HEADER SIZE
24
20
18
16
14
12
10
24
20
18
16
14
12
10
8
6
WT
WRT
WRT
WRT
WRT
WRT
WOL
WOL
WOL
WT
WRT
WRT
WRT
WRT
WRT
WOL
WOL
WT
WRT
WRT
WRT
WRT
WOL
WOL
WT
WRT
WRT
WRT
WRT
WOL
WT
WRT
WRT
WRT
WOL
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
4
3
2
1 1/2
1
3/4
1/2
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
Socket Weld Tee
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL
TOL
WOL
WRT
WOL
WOL
WOL
WOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
Sockolet
Threadolet
WT
WRT
WRT
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WOL
WRT
WT
WRT
WT
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
Weldolet
Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
A04N
Document No
Revision
0
1
Date
Description
20-Dec-2013
5-Mar-2014
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-50F / +600F
-46C / 316C
NONE
413 psig
28.5 barg
Pipe Size
Pipe
1/2"
Sch
Ends
Matl
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
2"
3"
Sch 40S
4"
6"
8"
ASTM A-312-TP316/316L
Sch
Flanges Rating
Matl
10"
12"
14"
Sch 10S
Beveled End (BE)
16"
18"
20"
24"
150# RF SW (note 2)
Fittings
Unions
Plugs
Couplings
Nipples (thd x thd)
Nipples (PE x thd)
Swages (thd x thd)
Swages (PE x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting (Note 5)
VALVES
Not required unless pipe is externally coated. If provided, washers are to be 316 stainless steel
Gate (4)
A1R-S
Ball (4,5)
A2R-SN, A2RF-SN
A4R-SN
A5R-SN, A5RG-SN, A5RW-SN
A7RG-SN, A7RW-SN
B utterfly (5)
Needle /
Gauge
G6S-SN, G9S-SN
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF connections
PSIG
Temp C
BAR
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will be provided to indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 316/316L
-50 to 100
200
300
275
235
215
-46 to 38
50
100
19
18.4
16.2
400
500
600
195
170
140
150
200
250
14.8
13.7
12.1
650
700
750
125
110
95
300
325
350
10.2
9.3
8.4
8 Seamless pipe and weld fittings may be substituted for ERW pipe and weld fittings.
800
80
375
400
425
7.4
6.5
5.5
1 1/2
3/4
1/2
SWT
SWTS
SWTS
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
20
24
WT
WRT
20
18
16
WT
18
16
14
WRT
WRT
WRT
12
10
8
6
4
14
12
10
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
3
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
TOL
Sockolet
Threadolet
WOL
WRT
Weldolet
Butt Weld Reducing Tee
WT
Specification
A06
Document No
Revision
Date
Description
20-Dec-2013
5-Mar-2014
SR
OB
GD
SR
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-20F / +400F
-29C / +204C
None
435 psig
30 barg
Pipe Size
1/2"
Sch
Pipe
Ends
3/4"
1"
Sch 80S
1-1/2"
2"
3"
Sch 40S
4"
6"
8"
10"
12"
14"
Sch 10S
16"
18"
20"
24"
Matl
Sch
Flanges Rating
150# RF SW
150# RFWN
ASTM A-182-F51
Matl
Fittings
Unions
Plugs
Couplings
Sockolets
Threadolets
Seamless, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Weldolets
Gaskets
Gate (4)
A1R-X
A2R-X, A2RF-X
VALVES
Ball (4,5)
A4R-X
A5R-X, A5RG-X, A5RW-X
A7RG-X, A7RW-X
B utterfly (5)
Needle /
Gauge
G6S-X, G9S-X
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Duplex stainless steel body valves may be forged or castings
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Not applicable
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
Temp F
PSIG
Temp C
-20 to 100
290
-29 to 38
20
200
260
50
19.5
300
230
100
17.7
400
200
150
15.8
500
170
200
13.8
600
140
250
12.1
300
10.2
325
9.3
3/4
1/2
BAR
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
WRT
WT
18
WRT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
1 1/2
WT
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT
PIPING SPECIFICATION - ASME CLASS 150, 2205 DUPLEX STAINLESS STEEL (NACE)
A06N
Document No
Revision
0
1
Rating
Piping Code
Sch
Ends
ASME B31.3
Matl
Fittings
Unions
Temp Range
-20F / +400F
-29C /204C
3/4"
1"
Sch 80S
Plain End (PE)
Matl
Sch
Flanges Rating
1-1/2"
Hydrotest
Pressure
Service
None
435 psig
30 barg
6"
8"
10"
12"
14"
Sch 10S
18"
20"
24"
Seamless, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Bolting
Gate (4)
A1R-XN
Ball (4,5)
A2R-XN, A2RF-XN
A4R-XN
A5R-XN, A5RG-XN, A5RW-XN
A7RG-XN, A7RW-XN
B utterfly (5)
Needle /
Gauge
G6S-XN, G9S-XN
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
BRANCH SIZE
16"
Sockolets
VALVES
Corrosion
Allowance
Threadolets
Weldolets
Gaskets
Couplings
Nipples (thd x thd)
Nipples (PE x thd)
4"
150# RF SW
2"
3"
Sch 40S
Description
Cameron standard - Issued for Design
Revise Pipe Sch, Nipples, Swages
Plugs
Date
20-Dec-2013
5-Mar-2014
Material / Group
1/2"
Specification
24
WT
20
18
16
24
14
12
10
20
18
16
14
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
12
10
8
WRT
WOL
WOL
WRT
WRT
WOL
WRT
WRT
WOL
WRT
WRT
WRT
6
4
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
Temp F
PSIG
Temp C
BAR
-20 to 100
200
300
290
260
230
-29 to 38
50
100
20
19.5
17.7
400
500
600
200
170
140
150
200
250
300
15.8
13.8
12.1
10.2
325
9.3
1/2
1 1/2
3/4
SWT
SWTS
SWT
1 1/2
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
SWT Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWTS
WT
SWTS
SWTS
Butt Weld Tee
SWT
PIPING SPECIFICATION - ASME CLASS 150, 2507, SUPER DUPLEX STAINLESS STEEL
Specification
A08
Document No
Date
Description
Revision
0
20-Dec-2013
5-Mar-2014
SR
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME 150
ASME B31.3
-20F / +600F
-29C / 316C
None
435 psig
30 barg
Pipe Size
Pipe
Sch
1/2"
3/4"
1"
Sch 80S
Ends
1-1/2"
2"
3"
Sch 40S
4"
6"
8"
10"
12"
14"
Sch 10S
16"
18"
20"
24"
Matl
Sch
Flanges Rating
150# RF SW
150# RFWN
ASTM A-182-F53
Matl
Fittings
Unions
Plugs
Couplings
Swages
(PE both ends)
Sockolets
Threadolets
Seamless, ASTM A-815-UNS S32750 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Weldolets
Gaskets
VALVES
A1R-D
Ball (4,5)
A2R-D, A2RF-D
A4R-D
A5R-D, A5RGXN, A5RW-D
A7RG-D, A7RW-D
B utterfly (5)
Needle
G6S-D, G9S-D
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Super Duplex SS body valves may be forged or castings.
5 Valves with elastomer seats and/or seals may not be ratedf for full ANSI pressure-termperature values.
seal materials. Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Not applicable
7 Not applicable
Temp F
-20 to 100
200
300
400
500
600
PSIG
290
260
230
200
170
140
Temp C
-29 to 38
50
100
150
200
250
300
325
BAR
20
19.5
17.7
15.8
13.8
12.1
10.2
9.3
1 1/2
3/4
1/2
8 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
WRT
WT
18
WRT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT
Specification
A08N
Document No
Revision
0
1
Rating
Piping Code
ASME B31.3
1/2"
Sch
Pipe
Ends
Matl
Date
20-Dec-2013
5-Mar-2014
Material / Group
Temp Range
-20F / +600F
-29C / 316C
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
Description
Cameron standard - Issued for Design
2"
3"
Sch 40S
SR
SR
4"
OB
SB
GD
GD
Corrosion
Allowance
Hydrotest
Pressure
Service
None
435 psig
30 barg
6"
8"
10"
12"
14"
Sch 10S
Beveled End (BE)
16"
18"
20"
24"
ASTM A-182-F53
Seamless, ASTM A-815-UNS S32750 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Sch
Flanges Rating
Matl
Fittings
Unions
Plugs
Couplings
Swages
(PE both ends)
Sockolets
Threadolets
Weldolets
Gaskets
VALVES
Bolting
Gate (4)
A1R-DN
Ball (4,5)
A2R-DN, A2RF-DN
A4R-DN
A5R-DN, A5RG-XN, A5RW-DN
A7RG-DN, A7RW-XN
B utterfly (5)
Needle /
Gauge
G6S-DN, G9S-DN
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Super Duplex SS body valves may be forged or castings.
5 Valves with elastomer seats and/or seals may not be ratedf for full ANSI pressure-termperature values.
seal materials. Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Not applicable
Temp F
PSIG
Temp C
BAR
-20 to 100
200
290
260
-29 to 38
50
20
19.5
300
230
100
17.7
400
500
200
170
150
200
15.8
13.8
600
140
250
300
12.1
10.2
325
9.3
3/4
1/2
SWT
SWTS
SWT
7 Not applicable
8 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
BRANCH SIZE
HEADER SIZE
20
24
24
WT
18
16
14
12
10
20
18
WRT
WRT
WT
WRT
WT
16
WRT
WRT
WRT
WT
14
12
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
10
8
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
4
3
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
1 1/2
WT
1 1/2
1
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SWTS
SWT
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
Specification
B01
Document No
Rating
Piping Code
ASME B31.3
1/2"
3/4"
Sch
Pipe
Revision
Date
20-Dec-2013
Description
5-Mar-2014
Material / Group
Temp Range
-20F / +600F
-29C / 316C
1"
1-1/2"
SCH 80
2"
3"
SR
OB
GD
SR
SB
GD
4"
Corrosion
Allowance
Hydrotest
Pressure
0.0625" (1.6mm)
1110 psig
76.5 barg
6"
8"
10"
Service
Liquids and Vapors - General Process
12"
Sch 40
14"
16"
18"
20"
Sch 40
STD
Ends
24"
Matl
300# RF SW (Note 2)
Seamless, ASTM A-234 WPB, Butt Weld, Bore to match pipe (Note 3)
Sch
Flanges Rating
ASTM A-105
Matl
Fittings
Unions
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
(FF Flanges) 1/16 thk, ANSI B16.21, Full-Faced, Synthetic Compressed Fiber with Nitrile Binder, Klinger C4401 or equivalent
Bolts / Cap Screws, Alloy Steel, A-193-B7, Fluorocote No. 1 finish
Bolting
Gate (4)
B1R
VALVES
Ball (4,5)
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
Temp F
Temp C
BAR
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
-20 to 100
740
-29 to 38
51.1
200
680
50
50.1
4 Carbon steel body valves may be A-105 forged steel or A216-WCB Casting
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
300
655
100
46.6
400
635
150
45.1
500
605
200
43.8
600
570
250
41.9
650
550
300
39.8
700
530
325
38.7
750
505
350
37.6
800
410
375
36.4
400
34.7
425
28.8
3/4
1/2
SWT
SWTS
SWT
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
WRT
WT
18
WRT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
1 1/2
WT
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
Specification
B01N
Document No
Rating
Piping Code
ASME B31.3
1/2"
Date
20-Dec-2013
Temp Range
-20F / +600F
-29C / 316C
1-1/2"
2"
3"
4"
OB
GD
Hydrotest
Pressure
Service
0.125" (3.2mm)
1110 psig
76.5 barg
6"
8"
10"
12"
14"
16"
Sch 60
18"
20"
24"
300# RF SW (Note 2)
ASTM A-105
3000# FS, A-105 (Note 7)
3000# FS, SW, A-105 (Note 7)
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Gaskets
SR
Corrosion
Allowance
Sch
Flanges Rating
Weldolets
Sch 80
Matl
Matl
Fittings
Unions
Description
Cameron standard - Issued for Design
Material / Group
3/4"
1"
Sch 160
Sch
Ends
Revision
Seamless, ASTM A-234 WPB, Butt Weld, Bore to match pipe (Note 3)
Bolting
VALVES
Ball (4,5)
B1R-N
B4R-N
B5R-N, B5RW-N
B7RG-N, B7RW-N
B utterfly (5)
Needle /
Gauge
G6S-SN, G9S-SN
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Carbon steel body valves may be A-105 forged steel or A216-WCB Casting
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
6 Items may be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
8 For full ANSI rating and -20F lower limit design temperature, A-333-6 seamless pipe and A-420-WPL6 weld
are required for nominal thicknesses >0.500".
9 Pipe material may be A106 Gr B seamless, API-5L Gr B seamless or A53B seamless
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
18
WRT
WRT
WT
WRT
WT
16
WRT
WRT
WRT
WT
14
12
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
8
6
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
Temp F
PSIG
Temp C
BAR
-20 to 100
740
-29 to 38
51.1
200
300
680
655
50
100
50.1
46.6
400
635
150
45.1
500
600
605
570
200
250
43.8
41.9
650
550
300
39.8
700
750
530
505
325
350
38.7
37.6
800
410
375
36.4
400
425
34.7
28.8
3/4
1/2
SWT
SWTS
SWT
1 1/2
WT
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
Specification
B02
Document No
Revision
0
1
Rating
ASME CLASS 300
Pipe Size
Piping Code
Material / Group
Temp Range
ASME B31.3
-50F / +600F
-46C / 316C
1/2"
3/4"
1"
Sch 80S
Plain End (PE)
Sch
Pipe
Ends
Matl
Sch
Flanges Rating
Matl
Fittings
Unions
1-1/2"
Sockolets
Threadolets
Weldolets
VALVES
(Notes 4, 6)
Check
GD
GD
Corrosion
Allowance
Hydrotest
Pressure
Service
None
1080 psig
74.5 barg
6"
8"
Sch 40S
10"
12"
14"
16"
18"
20"
Sch 80S
24"
Sch 80
D4S-S, D4Z-S
D5S-S, D5Z-S
B2R-S, B2RF-S
B4R-S
B5R-S, B5RG-S, B5RW-S
B7RG-S, B7RW-S
B utterfly (5)
Needle /
Gauge
OB
SB
Globe
SR
SR
Couplings
Ball (5)
4"
300# RF SW (Note 2)
Gate
3"
Bolting
2"
Description
Cameron standard - Issued for Design
Revise Pipe Sch, Nipples, Swages, Temp / Pressure chart
Plugs (Note 6)
Gaskets
Date
20-Dec-2013
5-Mar-2014
G6S-S, G9S-S
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF flanged connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 304 / 304L,
or may be certified for 304 with chemistry that meets 304L.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
6 Valves are suitable for -50F servie temperature
7 Welded construction to be used for in-line process piping. Threaded connections and fittings are permitted
for instrument take-offs, piping vent and drain valves
8 Seamless pipe and weld fittings may be substitured for ERW pipe and weld fittings.
Temp F
-50 to 100
PSIG
720
Temp C
-46 to 38
BAR
49.6
200
300
400
500
600
540
495
465
50
100
150
200
47.8
40.9
37
34.5
600
650
700
750
800
440
430
420
415
405
250
300
325
350
375
400
425
32.5
30.9
30.2
29.6
29
28.4
28
1 1/2
3/4
1/2
BRANCH SIZE
HEADER SIZE
24
20
18
16
14
12
10
8
6
4
3
2
1 1/2
1
3/4
1/2
24
WT
WRT
WRT
WRT
WRT
WRT
WOL
WOL
WOL
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
20
18
16
14
12
WT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WOL
WOL
WRT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
Socket Weld Tee
WRT
WOL
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WRT
WRT
WOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL
TOL
10
WT
WRT
WT
WRT
WRT
WOL
WRT
WOL
WOL
WOL
WOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
Sockolet
Threadolet
WT
WRT
WRT
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WOL
WRT
WT
WRT
WT
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
Weldolet
Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
B02N
Document No
Revision
0
1
Date
20-Dec-2013
20-Dec-2013
Description
Cameron standard - Issued for Design
Revise Pipe Sch, Nipples, Swages, Temp / Pressure chart
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-50F / +600F
-46C / 316C
None
1080 psig
74.5 barg
Pipe Size
Pipe
1/2"
3/4"
1"
Sch 80S
Sch
Ends
Matl
1-1/2"
2"
3"
4"
6"
8"
Sch 40S
10"
12"
OB
GD
SR
SB
GD
Service
Liquids and Vapors - General Process
14"
16"
18"
20"
Sch 80S
300# RF SW (Note 2)
Matl
Fittings
Unions
ASTM A-182-F304/304L
Seamless, ASTM A-403-WP304/304L, Butt Weld, Bore to match pipe (Note 3)
Plugs (Note 6)
Couplings
Sch
Flanges Rating
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
VALVES
(Notes 4, 6)
Gate
Ball (5)
Globe
Check
B1R-SN
B2R-SN, B2RF-SN
D4S-SN, D4Z-SN
D5S-S, D5Z-S
B4R-SN
B5R-SN, B5RW-SN
B7RG-SN
B utterfly (5)
Needle /
Gauge
24"
Sch 80
G6S-SN, G9S-SN
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF flanged connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 304 / 304L,
or may be certified for 304 with chemistry that meets 304L.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
6 Valves are suitable for -50F service temperature
7 Welded construction to be used for in-line process piping. Threaded connections and fittings are permitted
for instrument take-offs, piping vent and drain valves
8 Seamless pipe and weld fittings may be substitured for ERW pipe and weld fittings.
Temp F
-50 to 100
200
PSIG
720
600
Temp C
-46 to 38
50
BAR
49.6
47.8
300
400
500
600
650
700
750
540
495
465
440
430
420
415
100
150
200
250
300
325
350
40.9
37
34.5
32.5
30.9
30.2
29.6
800
405
375
400
425
29
28.4
28
1 1/2
3/4
1/2
BRANCH SIZE
HEADER SIZE
24
20
18
24
WT
WRT
WRT
20
18
16
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
8
6
4
WRT
WOL
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WOL
WRT
WRT
WRT
WOL
WOL
3
2
1 1/2
1
3/4
1/2
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
WOL
WOL
WOL
WOL
WOL
WOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
Socket Weld Tee
14
12
10
WRT
WRT
WRT
WOL
WOL
WT
WRT
WRT
WRT
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WOL
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL
TOL
WOL
WOL
WOL
WOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
SOL/TOL SOL/TOL
Sockolet
Threadolet
WRT
WOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
WOL
WRT
WT
WRT
WT
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL
Weldolet
Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
B02CR
Document No
Rating
ANSI 300LB
Pipe Size
Piping Code
Material / Group
ASME B31.3
1/2"
Sch
Pipe
3/4"
1"
Sch 80S
1-1/2"
Date
5-Mar-2014
Description
Corrosion
Allowance
Temp Range
-175F / +600F
2"
3"
None
4"
6"
10"
12"
Prepared
Checked
Approved
SB
TW
GD
Service
1080 psig
8"
Sch 40S
Ends
Matl
16"
18"
20"
Sch 80S
24"
Sch 80
ASTM A-312-TP304
300# RF SW
Matl
Fittings
ASTM A-182-F304
Seamless, ASTM A-403-WP304, Butt Weld, Bore to match pipe (Note 3)
Unions
Plugs
Sch
Flanges Rating
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
Gate
Globe
D2Z-SCR, D2ZF-SCR
D4Z-SCR, D4S-SCR
B2R-SCR, B2RF-SCR
B4R-SCR
Check
B5R-SCR, B5RW-SCR
B7R-SCR
Ball (5)
Valves
Rev No
B utterfly (5)
Needle
G6S-SCR, G9S-SCR
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Threaded connections are not permitted beneath insulation. Seal welding is premitted.
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Materials may be s pecified and purchased as grade 304L, or dual certified 304 / 304L
Grade 316 or 316/316L may be substituted for Grade 304 or 304/304L
5 Standard valves having elastomer seats are typically rated for 250 ps ig maximum temperature. Valves with
elastomer seals may not be rated for full ANSI pressure-temperature values. Refer to P&ID's and/or
equipment data sheets for sys tem design pressure and upper limit design temperature. High temperature
ball and butterfly valves will be required to be metal seated.
6 Valves are suitable for Cryogenic temperature service to -175F
7 Welded construction to be used for in-line process piping through the first instrument is olation valve.
Threaded connection are permitted only for connections to instruments outside of insulation
Temp F
-175 to 100
200
300
400
500
600
650
700
750
800
PSIG
720
600
540
495
465
440
430
420
415
405
Temp C
-115 to 38
50
100
150
200
250
300
325
350
375
400
425
BAR
49.6
47.8
40.9
37
34.5
32.5
30.9
30.2
29.6
29
28.4
28
1 1/2
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
20
24
24
WT
20
18
WRT
WRT
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
8
6
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
4
3
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
2
1 1/2
WOL
SOL
WOL
SOL
WOL
SOL
WOL
SOL
WOL
SOL
WOL
SOL
WOL
SOL
WOL
SOL
WOL
SOL
WRT
SOL
WRT
SOL
WT
SOL
SWT
1
3/4
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SWTS
SWTS
1/2
SOL
SWTS
SOL
SOL
SOL
SOL
Sockolet
SOL
SOL
WOL
SOL
Weldolet
SOL
SOL
SWTS
WT
TOL
Threadolet
WRT
SWT
18
16
SOL
SOL
SOL
Full size SW Tee with Swage
Socket Weld Tee
14
12
10
SWTS
SWTS
Butt Weld Tee
SWT
Specification
B03
Document No
Revision
Date
20-Dec-2013
Description
5-Mar-2014
SR
OB
GD
SR
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-50F / +600F
-46C / 316C
0.0625" (1.6mm)
1110 psig
76.5 barg
Pipe Size
Pipe
1/2"
Sch
3/4"
1"
Sch 80
Ends
1-1/2"
2"
3"
4"
6"
8"
10"
Sch 40
12"
14"
Sch STD
16"
18"
20"
Sch 40
24"
Matl
Sch
Flanges Rating
300# RF SW
300# RFWN
ASTM A-350-LF2, Cl. 1
Matl
Fittings
Unions
Seamless, ASTM A-420 WPL6, Butt Weld, Bore to match pipe (Note 3)
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
VALVES
B1R-L
Ball (4,5)
B2R-L, B2RF-L
B4R-L
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 -50 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
Temp F
Temp C
BAR
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
-50 to 100
740
-46 to 38
51.1
200
680
50
50.1
4 Carbon Steel body valves may be A-350-LF2, Cl.1 forged steel or A-352-LCC Castings. A-352-LCB castings
300
655
100
46.6
may be used provided the system design pressure and temperature are compatible with B16.5 ratings.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
400
635
150
45.1
500
605
200
43.8
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
6 Items may be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
600
570
250
41.9
650
550
300
39.8
700
750
530
505
325
350
38.7
37.6
800
410
375
36.4
400
34.7
425
28.8
3/4
1/2
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
WRT
WT
18
16
WRT
WRT
WRT
WRT
WT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
1 1/2
WT
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT
PIPING SPEC - ASME CLASS 300, LOW TEMPERATURE CARBON STEEL (NACE)
B03N
Document No
Rating
Piping Code
ASME B31.3
1/2"
Sch
Pipe
Revision
0
Date
20-Dec-2013
5-Mar-2014
Temp Range
-50F / +600F
-46C / 316C
1-1/2"
2"
3"
SR
GD
Hydrotest
Pressure
Service
0.125" (3.2mm)
1110 psig
76.5 barg
6"
8"
10"
Sch 40
12"
14"
Sch STD
16"
18"
20"
Sch 40
24"
300# RF SW
Matl
Fittings
Unions
Plugs (Note 6)
Sch
Flanges Rating
SB
Corrosion
Allowance
4"
Ends
Matl
Description
Cameron standard - Issued for Design
Material / Group
3/4"
1"
Sch 80
Specification
Couplings
3000# FS, Full, Threaded, A-350-LF2, Cl. 1
Nipples (thd x thd)
Sch 160 Seamless, A-333-6
Nipples (PE x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
Gate (4)
VALVES
Ball (4,5)
B4R-LN
B5R-LN, B5RG-LN, B5RW-LN
B7RG-LN, B7RW-LN
B utterfly (5)
Needle /
Gauge
B2R-LN, B2RF-LN
G6S-SN, G9S-SN
Notes: 1 -50 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Temp F
PSIG
Temp C
BAR
-50 to 100
200
740
680
-46 to 38
50
51.1
50.1
300
400
655
635
100
150
46.6
45.1
500
605
200
43.8
600
650
570
550
250
300
41.9
39.8
700
750
530
505
325
350
38.7
37.6
800
410
375
400
36.4
34.7
425
28.8
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
WT
20
24
18
16
14
12
10
20
18
WRT
WRT
WT
WRT
WT
16
WRT
WRT
WRT
WT
14
12
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
10
8
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
6
4
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
SWTS
WT
SWT
TOL
Threadolet
WRT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
B04
Document No
Rating
ASME CLASS 300
Pipe Size
5-Mar-2014
Material / Group
Temp Range
ASME B31.3
-50F / +600F
-46C / 316C
1/2"
Description
Cameron standard - Issued for Design
300# RF SW (Note 2)
Unions
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
3/4"
1"
1-1/2"
2"
3"
4"
Sch 80S
Sch 40S
Plain End (PE)
Seamless, ASTM A-312-TP316/316L
Fittings
SR
SB
GD
Corrosion
Allowance
Hydrotest
Pressure
Service
None
1080 psig
74.5 barg
6"
8"
10"
12"
Sch 40S
Beveled End (BE)
14"
16"
18"
20"
Sch 80S
24"
Sch 80
Bolting
VALVES
(Notes 4, 6)
Date
20-Dec-2013
Piping Code
Sch
Pipe
Ends
Matl
Sch
Flanges Rating
Matl
Gaskets
Revision
0
Gate
Ball (5)
Globe
D4S-S, D4Z-S
D5S-S, D5Z-S
Check
B utterfly (5)
Needle /
Gauge
B2R-S, B2RF-S
B4R-S
B5R-S,B5RG-S, B5RW-S
B7RG-S, B7RW-S
G6S-S, G9S-S
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to equipment with FF flanged connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 316 / 316L,
or may be certified for 316 with chemistry that meets 316L.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
6 Valves are suitable for -50F servie temperature
7 Welded construction to be used for in-line process piping. Threaded connections and fittings are permitted
for instrument take-offs, piping vent and drain valves
8 Seamless pipe and weld fittings may be substitured for ERW pipe and weld fittings.
Temp F
-50 to 100
PSIG
720
Temp C
-46 to 38
BAR
49.6
200
300
400
500
600
650
620
560
515
480
450
440
50
100
150
200
250
300
48.1
42.2
38.5
35.7
33.4
31.6
700
435
325
30.9
750
800
425
420
350
375
30.3
29.9
400
425
29.4
29.1
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
20
18
24
WT
WRT
WRT
20
18
16
14
12
10
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
8
6
4
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WOL
WT
WRT
WRT
WOL
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
1
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SWTS
SWT
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWTS
SWT
SOL
TOL
Sockolet
Threadolet
WOL
WRT
Weldolet
Butt Weld Reducing Tee
WT
B04N
Document No
Revision
Date
20-Dec-2013
Description
5-Mar-2014
SR
OB
GD
SR
SB
GD
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotes t
Pressure
ASME B31.3
-50F / +600F
-46C / 316C
None
1080 psig
74.5 barg
Pipe
1/2"
Sch
Ends
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
2"
3"
4"
6"
8"
Sch 40S
10"
Service
Liquids and Vapors - General Process
12"
14"
16"
18"
20"
Sch 80S
24"
Sch 80
Matl
Rating
Pipe Size
Specification
Sch
Flanges Rating
300# RF SW (Note 2)
Matl
Fittings
Unions
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
(FF Flanges ) 1/16 thk, ANSI B16.21, Full-Faced, Synthetic Compres sed Fiber with Nitrile Binder, Klinger C4401 or equivalent
Bolts / Cap Screws, Alloy Steel, A-193-B8
Bolting
VALVES
(Notes 4, 6)
Gate
B1R-SN
Globe
Check
D5S-SN, D5Z-SN
Ball (5)
B2R-SN, B2RF-SN
B4R-SN
B5R-SN, B5RG-SN, B5RW-SN
B7RG-SN, B7RW-SN
B utterfly (5)
Needle /
Gauge
G6S-SN, G9S-SN
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness .
2 Use FF flange for connection to equipment with FF flanged connections
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 316 / 316L,
or may be certified for 316 with chemis try that meets 316L.
Temp F
PSIG
Temp C
BAR
-50 to 100
720
-46 to 38
49.6
200
300
620
560
50
100
48.1
42.2
400
515
150
38.5
5 Valves with elas tomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
500
480
200
35.7
600
450
250
33.4
650
700
440
435
300
325
31.6
30.9
750
425
350
30.3
8 Seamless pipe and weld fittings may be subs titured for ERW pipe and weld fittings.
800
420
375
29.9
400
29.4
425
29.1
3/4
1/2
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
18
WRT
WRT
WT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
8
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
1 1/2
WT
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full s ize SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
SWTS
WT
SWT
TOL
Threadolet
WRT
SWT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
B06
Document No
Revision
0
1
Date
Description
20-Dec-2013
5-Mar-2014
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-20F / +400F
-29C /204C
None
1125 psig
77.6 barg
Pipe Size
1/2"
Sch
Pipe
Ends
Matl
1-1/2"
Couplings
Sockolets
Threadolets
10"
12"
Sch 40S
Beveled End (BE)
16"
18"
20"
24"
Sch 80S
Seamless, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Bolting
VALVES
8"
Gaskets
6"
GD
300# RFWN
Weldolets
4"
SB
ASTM A-182-F51
3"
300# RF SW
Plugs
2"
SR
Service
Sch
Flanges Rating
Matl
Fittings
Unions
3/4"
1"
Sch 80S
Plain End (PE)
Gate (4)
Ball (4,5)
B2R-X, B2RF-X
B4R-X
B utterfly (5)
G6S-X, G9S-X
Needle / Gauge
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Temp F
-20 to 100
200
PSIG
750
745
Temp C
-29 to 38
50
BAR
51.7
51.7
300
400
665
615
100
150
50.7
45.9
500
600
580
555
200
250
42.7
40.5
300
325
38.9
38.2
3/4
1/2
BRANCH SIZE
HEADER SIZE
20
24
24
WT
18
16
14
20
18
WRT
WRT
WT
WRT
WT
16
14
12
WRT
WRT
WRT
WRT
WRT
WRT
10
8
WOL
WOL
6
4
3
2
12
10
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
1
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SWTS
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
SWTS
SWTS
WT
SWT
TOL
Threadolet
WRT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
PIPING SPECIFICATION - ASME CLASS 300, 2205 DUPLEX STAINLESS STEEL (NACE)
B06N
Document No
Revision
0
1
Date
20-Dec-2013
5-Mar-2014
Description
Cameron standard - Issued for Design
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-20F / +400F
-29C /204C
None
1125 psig
77.6 barg
1/2"
Sch
Pipe
1-1/2"
10"
Sch 40S
12"
Service
Liquids and Vapors - General Process
14"
16"
18"
20"
24"
Sch 80S
300# RFWN
Couplings
Seamless, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Sockolets
Threadolets
Gaskets
8"
GD
GD
ASTM A-182-F51
Weldolets
6"
300# RF SW
4"
OB
SB
Plugs
3"
SR
SR
Sch
Flanges Rating
2"
Ends
Matl
Matl
Fittings
Unions
3/4"
1"
Sch 80S
Rating
Pipe Size
Specification
Bolting
Gate (4)
B1R-XN
VALVES
Ball (4,5)
B utterfly (5)
Needle /
Gauge
B2R-XN, B2RF-XN
B4R-XN
B5R-XN, B5RG-XN, B5RW-XN
B7RG-XN, B7RW-XN
G6S-XN, G9S-XN
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Duplex SS body valves may be forged or castings.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Not applicable
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
Temp F
-20 to 100
200
300
400
500
600
PSIG
750
745
665
615
580
555
Temp C
-29 to 38
50
100
150
200
250
300
325
BAR
51.7
51.7
50.7
45.9
42.7
40.5
38.9
38.2
1 1/2
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
18
WRT
WRT
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
6
4
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
SWTS
WT
SWT
TOL
Threadolet
WRT
SWTS
SWTS
Butt Weld Tee
SWT
PIPING SPECIFICATION - ASME CLASS 300, 2507 SUPER DUPLEX STAINLESS STEEL
Specification
B08
Document No
Revision
0
1
Date
20-Dec-2013
5-Mar-2014
Description
Cameron standard - Issued for Design
Revise Pipe Sch, Nipples, Swages
OB
GD
SR
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-20F / +600F
-29C / 316C
None
1125 psig
77.6 barg
Pipe Size
Pipe
Sch
1/2"
3/4"
1"
Sch 80S
Ends
1-1/2"
300# RF SW
3000# FS, A-182-F53 (Note 8)
Unions
Plugs
Couplings
Sockolets
Threadolets
Gaskets
8"
10"
Sch 40S
12"
14"
16"
18"
24"
Sch 80S
300# RFWN
ASTM A-182-F53
Seamless, ASTM A-815-UNS S32750 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Gate (4)
B1R-D
Ball (4,5)
B2R-D, B2RF-D
B4R-D
B5R-D, B5RG-D, B5RW-D
B7RG-D, B7RW-D
B utterfly (5)
Needle /
Gauge
G6S-D, G9S-D
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Temp F
-20 to 100
200
300
400
PSIG
750
745
665
615
Temp C
-29 to 38
50
100
150
BAR
51.7
51.7
50.7
45.9
500
600
580
555
200
250
300
325
42.7
40.5
38.9
38.2
1 1/2
3/4
1/2
8 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
HEADER SIZE
BRANCH SIZE
20"
Bolting
VALVES
6"
Swages
(PE both ends)
Weldolets
4"
Matl
Fittings
3"
Matl
Sch
Flanges Rating
2"
24
WT
20
18
16
14
12
10
24
20
18
16
14
12
10
WRT
WRT
WRT
WRT
WRT
WOL
WT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
8
6
4
3
2
1 1/2
1
3/4
1/2
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
PIPING SPEC - ASME CLASS 300, 2507 SUPER DUPLEX STAINLESS STEEL (NACE)
B08N
Document No
Revision
0
1
Rating
Piping Code
ASME B31.3
1/2"
Flanges Rating
Matl
Fittings
Unions
Temp Range
2"
3"
4"
SR
SB
GD
Corrosion
Allowance
Hydrotest
Pressure
Service
None
1125 psig
77.6 barg
6"
8"
10"
Sch 40S
12"
14"
16"
18"
20"
24"
Sch 80S
300# RF SW
300# RFWN
ASTM A-182-F53
Seamless, ASTM A-815-UNS S32750 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Couplings
Nipples (thd x thd)
Nipples (PE x thd)
Description
-20F / +600F
-29C / 316C
Plugs
Date
20-Dec-2013
5-Mar-2014
Material / Group
3/4"
1"
Sch 80S
Sch
Ends
Matl
Sch
Specification
Swages
(PE both ends)
Sockolets
Threadolets
Weldolets
Gaskets
B2R-DN, B2RF-DN
VALVES
Ball (4,5)
B4R-DN
B5R-DN, B5RG-DN, B5RW-DN
B7RG-DN, B7RW-DN
B utterfly (5)
Needle /
Gauge
G6S-DN, G9S-DN
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
BRANCH SIZE
Refer to P&ID's and/or Equipment Data sheets for system upper limit design temperature.
6 Not applicable
7 Not applicable
8 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
HEADER SIZE
24
20
18
24
20
18
16
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
14
12
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
10
8
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
6
4
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WOL
WOL
WOL
1 1/2
1
3/4
1/2
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
16
14
12
SOL
TOL
10
WRT
WRT
WOL
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
Sockolet
Threadolet
WOL
WRT
Weldolet
Butt Weld Reducing Tee
Temp F
-20 to 100
200
300
400
500
600
PSIG
750
745
665
615
580
555
Temp C
-29 to 38
50
100
150
200
250
300
325
BAR
51.7
51.7
50.7
45.9
42.7
40.5
38.9
38.2
1 1/2
3/4
1/2
SWT
SWTS
SWTS
SWTS
SWT
SWTS
SWTS
SWT
SWTS
SWT
WT
Specification
D01
Document No
Revision
Date
20-Dec-2013
Description
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-20F / +600F
-29C / 316C
0.0625" (1.6mm)
2220 psig
153.1 barg
Pipe Size
Pipe
1/2"
3/4"
Sch
Ends
1"
1-1/2"
3"
4"
6"
8"
Sch 80
Flanges Rating
Matl
10"
SR
OB
GD
Service
12"
16"
18"
20"
24"
Matl
Sch
600# RF SW (Note 2)
Fittings
Unions
Plugs (Note 6)
Couplings
Nipples (thd x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
VALVES
2"
Gate (4)
D1R
Ball (4,5)
D2R, D2RF
D4R
D5R, D5RG, D5RW
D7RG, D7RW
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Carbon steel body valves may be A-105 forged steel or A-216-WCB casting
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Items may be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
8 For full ANSI rating and -20F lower limit design temperature, A-333-6 smls pipe and A-420-WPL6 weld
are required for nominal thicknesses > 0.500".
Temp F
-20 to 100
200
300
400
500
600
650
700
750
800
PSIG
1480
1360
1310
1265
1205
1135
1100
1060
1015
825
Temp C
-29 to 38
50
100
150
200
250
300
325
350
375
400
425
BAR
102.1
100.2
93.2
90.2
87.6
83.9
79.6
77.4
75.1
72.7
69.4
57.5
1 1/2
3/4
1/2
SWT
SWTS
SWT
9 Pipe materials may be supplied as A-106 Gr B seamless, API-5L Gr B seamless or A-53 gr. B seamless
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
10
24
20
WT
WRT
WT
18
16
WRT
WRT
WRT
WRT
WT
WRT
WT
14
12
10
WRT
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
8
6
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
4
3
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
SWTS
WT
SWT
TOL
Threadolet
WRT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
D01N
Document No
Revision
Date
20-Dec-2013
Description
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pres sure
ASME B31.3
-20F / +600F
-29C / 316C
0.125" (3.2mm)
2220 psig
153.1 barg
Pipe Size
1/2"
3/4"
Sch
Pipe
1"
Sch 160
1-1/2"
2"
3"
4"
6"
8"
10"
Ends
SR
AC
GD
Service
Liquids and Vapors - General Proces s
12"
Sch 80
14"
16"
18"
20"
24"
Matl
Sch
Flanges Rating
600# RF SW (Note 2)
Matl
Fittings
Unions
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
Nuts, Alloy Steel, sem i-finis hed, A-194-2H, Fluorocote No. 1 finish
VALVES
D1R-N
Ball (4,5)
D2R-N, D2RF-N
D4R-N
B utterfly (5)
Needle /
Gauge
G6S-SN, G9S-SN
Notes: 1 -20 / 100F press ure rating is us ed to determine the required pipe wall thicknes s.
2 Use FF flange for connection to FF cast iron or ductile iron flanges for equipment
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Carbon s teel body valves m ay be A-105 forged s teel or A-216-WCB casting
5 Valves with elastomer seats and/or s eals may not be rated for full ANSI pres sure-temperature values .
Refer to P&ID's and/or Equipment Data Sheets for s ystem upper limit design temperature.
6 Items m ay be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line proces s piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
8 For full ANSI rating and -20F lower lim it des ign tem perature, A-333-6 sm ls pipe and A-420-WPL6 weld
Temp F
-20 to 100
200
300
400
500
600
650
700
750
800
PSIG
1480
1360
1310
1265
1205
1135
1100
1060
1015
825
Temp C
-29 to 38
50
100
150
200
250
300
325
350
375
400
425
BAR
102.1
100.2
93.2
90.2
87.6
83.9
79.6
77.4
75.1
72.7
69.4
57.5
1 1/2
3/4
1/2
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
WRT
WT
18
WRT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT
Specification
D02
Document No
Revision
Date
Des cription
20-Dec-2013
5-Mar-2014
SR
OB
GD
SR
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corros ion
Allowance
Hydrotes t
Press ure
ASME 600
ASME B31.3
-50F / +600F
-46C / 316C
None
2220 psig
153.1 barg
Pipe Size
1/2"
Sch
Pipe
Ends
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
2"
3"
4"
Sch 40S
6"
8"
10"
Service
Liquids and Vapors - General Process
12"
14"
Sch 80S
16"
Sch 80
18"
20"
24"
Matl
Sch
Flanges Rating
600# RF SW (Note 2)
Matl
Fittings
Unions
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
Gas kets
Bolting
Washers, 316SS
D1R-S
Globe
Check
D5S-S, D5Z-S
VALVES
(Notes 4, 6)
Gate
Ball (5)
D2R-S, D2RF-S
D4R-S
D7RG-S, D7RW-S
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 100F press ure rating is used to determine the required pipe wall thicknes s.
2 Not applicable
PSIG
Temp C
BAR
-50 to 100
1440
-46 to 38
99.3
200
1200
50
95.6
4 Where materials are s hown to be dual certified, materials may be supplied dual certified for 304 / 304L,
or may be certified for 304 with chemis try that meets 304L.
300
1075
100
81.7
400
995
150
74
5 Valves with elastomer seats and/or seals may not be rated for full ANSI press ure-temperature values .
Refer to P&ID's and/or Equipment Data Sheets for system upper limit des ign temperature.
500
930
200
69
600
885
250
65
650
865
300
61.8
700
845
325
60.4
750
825
350
59.3
800
810
375
400
58.1
56.9
425
56
3/4
1/2
3 Butt weld reducing fittings shall be purchased to the heavier pipe s chedule.
Piping drawing notes will indicate where internal beveling is required
8 Sealess pipe and weld fittings may be substitued for ERW pipe and weld fittings.
BRANCH SIZE
HEADER SIZE
24
24
WT
20
18
16
14
12
10
20
WRT
WT
18
WRT
WRT
WT
16
WRT
WRT
WRT
WT
14
WRT
WRT
WRT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT
D02N
Document No
Revision
Date
0
1
20-Dec-2013
5-Mar-2014
Description
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-50F / +600F
-46C / 316C
None
2160 psig
148.9 barg
1/2"
3/4"
1"
1-1/2"
2"
3"
4"
Sch 80S
Sch 40S
Plain End (PE)
Seamless, ASTM A-312-TP304/304L
Sch
Pipe
Ends
Matl
Sch
Flanges Rating
600# RF SW (Note 2)
Rating
Pipe Size
Specification
6"
8"
Sch 80S
10"
12"
SR
SR
OB
SB
GD
GD
Service
Liquids and Vapors - General Process
14"
16"
Sch 80
18"
20"
24"
Matl
Fittings
Unions
Plugs (Note 6)
Couplings
3000# FS, Full, Threaded, A-182-F304
Nipples (thd x thd)
Sch 80S smls A-312-TP304
Nipples (PE x thd)
Sch 80S smls A-312-TP304/304L
Swages (thd x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
VALVES
(Notes 4, 6)
Gate
Ball (5)
Globe
Check
B utterfly (5)
Needle /
Gauge
D2R-SN, D2RF-SN
D4R-SN
D5R-SN, D5RG-SN, D5RW-SN
D7RG-SN, D7RW-SN
G6S-SN, G9S-SN
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 304 / 304L,
8 Sealess pipe and weld fittings may be substitued for ERW pipe and weld fittings.
Temp F
-50 to 100
200
PSIG
1440
1200
Temp C
-46 to 38
50
BAR
99.3
95.6
300
400
1075
995
100
150
81.7
74
500
600
650
700
930
885
865
845
200
250
300
325
69
65
61.8
60.4
750
800
825
810
350
375
400
59.3
58.1
56.9
425
56
3/4
1/2
BRANCH SIZE
HEADER SIZE
24
20
18
16
14
12
10
8
6
4
3
2
1 1/2
1
3/4
1/2
24
WT
WRT
WRT
WRT
WRT
WRT
20
18
16
14
12
WT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
SOL
Sockolet
WOL
Weldolet
Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
1 1/2
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
D02CR
Document No
Rating
ANSI 600LB
Pipe Size
Pipe
Date
5-Mar-2014
Description
Cameron Standard - Issued for Design
Prepared
Checked
Approved
SB
TW
GD
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-175F / +600F
None
2160 psig
1/2"
Sch
Ends
3/4"
1"
Sch 80S
Plain End (PE)
1-1/2"
2"
3"
4"
Sch 40S
6"
8"
Sch 80S
10"
12"
14"
16"
Sch 80
18"
20"
24"
Matl
Sch
Flanges Rating
Matl
Fittings
Rev No
600# RF SW
ASTM A-182-F304
Seamless, ASTM A-403-WP304, Butt Weld, Bore to match pipe (Note 3)
Unions
Plugs
Couplings
3000# FS, Full, Threaded, A-182-F304
Nipples (thd x thd)
Sch 80S smls A-312-TP304
Nipples (PE x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
Globe
D1R-SCR
D2R-SCR, D2RF-SCR
D4R-SCR
Check
D5R-SCR, D5RW-SCR
D7R-SCR
Gate
Valves
Ball (5)
B utterfly (5)
Needle
G6S-SCR, G9S-SCR
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Threaded connections are not permitted beneath insulation. Seal welding is premitted.
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
Temp F
PSIG
Temp C
BAR
-175 to 100
200
720
600
-115 to 38
50
49.6
47.8
4 Materials may be specified and purchased as grade 304L, or dual certified 304 / 304L
Grade 316 or 316/316L may be substituted for Grade 304 or 304/304L
300
400
540
495
100
150
40.9
37
5 Standard valves having elastomer seats are typically rated for 250 psig maximum temperature. Valves with
elastomer seals may not be rated for full ANSI pressure-temperature values. Refer to P&ID's and/or
500
600
650
465
440
430
200
250
300
34.5
32.5
30.9
700
750
420
415
325
350
30.2
29.6
800
405
375
400
29
28.4
425
28
3/4
1/2
SWT
SWTS
SWT
equipment data sheets for system design pressure and upper limit design temperature. High temperature
ball and butterfly valves will be required to be metal seated.
6 Valves are suitable for Cryogenic temperature service to -175F
7 Welded construction to be used for in-line process piping through the first instrument isolation valve.
Threaded connection are permitted only for connections to instruments outside of insulation
BRANCH SIZE
HEADER SIZE
24
20
24
20
18
WT
WRT
WRT
WT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
10
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
8
6
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
4
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
1 1/2
1
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
3/4
1/2
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SWTS
SWT
18
16
14
12
SOL
TOL
10
Sockolet
Threadolet
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SWT
SWTS
SWT
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SOL
SWTS
SWTS
SWTS
SWTS
WOL
WRT
Weldolet
Butt Weld Reducing Tee
1 1/2
WT
D03
Document No
Revision
0
1
Specification
Date
20-Dec-2013
5-Mar-2014
Description
Cameron standard - Issued for Design
Revise Temp / Pressure chart
OB
GD
SR
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-50F / +600F
-46C / 316C
0.0625" (1.6mm)
2220 psig
153.1 barg
Pipe Size
1/2"
3/4"
1"
1-1/2"
2"
3"
4"
6"
Sch
Pipe
Ends
600# RF SW
3000# FS, A-350-LF2, Cl. 1 (Note 7)
3000# FS, SW, A-350-LF2, Cl. 1 (Note 7)
Plugs (Note 6)
Couplings
Sockolets
Threadolets
Weldolets
VALVES
18"
20"
24"
Seamless, ASTM A-420 WPL6, Butt Weld, Bore to match pipe (Note 3)
D4R-L
D5R-L, D5RG-L, D5RW-L
D7RG-L, D7RW-L
Needle /
Gauge
16"
600# RFWN
Unions
Ball (4,5)
14"
Fittings
Gate (4)
12"
Matl
Bolting
10"
Matl
Sch
Flanges Rating
Gaskets
8"
Sch 80
G6S-S, G9S-S
Notes: 1 -50 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Carbon steel body valves may be A-350-LF2, Cl.1 forged steel or A-352-LCC castings. A-352-LCB castings
may be used provided the system design pressure and temperature are compatible with B16.5 ratings.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Items may be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
8 For full ANSI rating and -20F lower limit design temperature, A-333-6 smls pipe and A-420-WPL6 weld
are required for nominal thicknesses > 0.500".
PSIG
1480
Temp C
-46 to 38
BAR
102.1
200
300
1360
1310
50
100
100.2
93.2
400
500
600
650
1265
1205
1135
1100
150
200
250
300
90.2
87.6
83.9
79.6
700
750
800
1060
1015
825
325
350
375
400
77.4
75.1
72.7
69.4
425
57.5
3/4
1/2
BRANCH SIZE
HEADER SIZE
24
WT
20
18
16
14
12
10
24
20
18
16
14
12
10
WRT
WRT
WRT
WRT
WRT
WOL
WT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
8
6
4
3
2
1 1/2
1
3/4
1/2
WOL
WOL
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL
SOL/TOL
SOL/TOL
SWTS
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
1 1/2
SWT
SWTS
SWTS
SWTS
WT
SWT
SWTS
SWT
SWTS
SWTS
Butt Weld Tee
SWT
PIPING SPECIFICATION - ASME CLASS 600, LOW TEMP CARBON STEEL (NACE)
D03N
Document No
0
1
Rating
Piping Code
ASME 600
Pipe Size
ASME B31.3
1/2"
3/4"
20-Dec-2013
5-Mar-2014
Temp Range
-50F / +600F
-46C / 316C
1-1/2"
2"
3"
4"
GD
GD
Hydrotest
Pressure
Service
0.125" (3.2mm)
2220 psig
153.1 barg
6"
8"
Sch 80
10"
Ends
Matl
OB
SB
Corrosion
Allowance
Sch
Pipe
SR
SR
Material / Group
1"
Specification
12"
14"
16"
18"
20"
24"
Sch
Flanges Rating
Matl
600# RF SW
600# RFWN
ASTM A-350-LF2, Cl. 1
Fittings
Unions
Plugs (Note 6)
Seamless, ASTM A-420 WPL6, Butt Weld, Bore to match pipe (Note 3)
Couplings
3000# FS, Full, Threaded, A-350-LF2, Cl. 1
Nipples (thd x thd)
Sch 160 Seamless, A-333-6
Nipples (PE x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
VALVES
Gate (4)
D1R-LN
Ball (4,5)
D2R-LN, D2RF-LN
B utterfly (5)
Needle /
Gauge
D4R-LN
D5R-LN, D5RG-LN, D5RW-LN
D7RG-LN, D7RW-LN
G6S-SN, G9S-SN
Notes: 1 -50 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Carbon steel body valves may be A-350-LF2, Cl.1 forged steel or A-352-LCC castings. A-352-LCB castings
may be used provided the system design pressure and temperature are compatible with B16.5 ratings.
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for system upper limit design temperature.
6 Items may be cad plated, zinc plated, or galvanized
7 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
8 For full ANSI rating and -20F lower limit design temperature, A-333-6 smls pipe and A-420-WPL6 weld
Temp F
PSIG
Temp C
BAR
-50 to 100
200
300
1480
1360
1310
-46 to 38
50
100
102.1
100.2
93.2
400
500
1265
1205
150
200
90.2
87.6
600
650
700
1135
1100
1060
250
300
325
83.9
79.6
77.4
750
800
1015
825
350
375
75.1
72.7
400
425
69.4
57.5
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
20
24
WT
WRT
20
18
16
14
12
WT
18
16
WRT
WRT
WRT
WRT
WT
WRT
WT
14
12
10
WRT
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
8
6
WOL
WOL
WOL
WOL
4
3
2
WOL
WOL
WOL
WOL
WOL
WOL
10
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
1
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SWTS
SWT
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWTS
SWT
SOL
TOL
Sockolet
Threadolet
WOL
WRT
Weldolet
Butt Weld Reducing Tee
WT
Specification
D04
Document No
Revision
0
1
Rating
ASME CLASS 600
Pipe Size
Pipe
Plugs (Note 6)
Description
Piping Code
Material / Group
Temp Range
ASME B31.3
-50F / +600F
-46C / 316C
1/2"
Sch
Ends
Matl
Sch
Flanges Rating
Matl
Fittings
Unions
Date
20-Dec-2013
5-Mar-2014
3/4"
1"
Sch 80S
1-1/2"
2"
3"
4"
Sch 40S
Corrosion
Allowance
Hydrotest
Pressure
Service
None
2160 psig
148.9 barg
6"
8"
Sch 80S
10"
12"
14"
16"
Sch 80
18"
20"
24"
Couplings
3000# FS, Full, Threaded, A-182-F316
Nipples (thd x thd)
Sch 80S smls A-312-TP316
Nipples (PE x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
Gate
VALVES
(Notes 4, 6)
Ball (5)
Globe
Check
D1R-S
D2R-S, D2RF-S
D4R-S
D5R-S, D5RG-S, D5RW-S
D7RG-S, D7RW-S
B utterfly (5)
Needle /
Gauge
G6S-S, G9S-S
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 316 / 316L,
Temp F
-50 to 100
PSIG
1440
Temp C
-46 to 38
BAR
99.3
200
300
400
1240
1120
1025
50
100
150
96.2
84.4
77
500
600
650
700
955
900
885
870
200
250
300
325
71.3
66.8
63.2
61.8
750
800
855
845
350
375
400
425
60.7
59.8
58.9
58.3
1 1/2
3/4
1/2
SWT
SWTS
SWTS
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
20
18
24
WT
WRT
WRT
20
18
16
14
12
WT
WRT
WT
16
14
12
10
WRT
WRT
WRT
WOL
WRT
WRT
WRT
WRT
8
6
4
3
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
10
WRT
WRT
WRT
WRT
WT
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WOL
WOL
WOL
WRT
WRT
WOL
WOL
WRT
WRT
WOL
WOL
WT
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
2
1 1/2
1
3/4
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
SWT Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWTS
WT
SWTS
SWTS
Butt Weld Tee
SWT
D04N
Document No
Revision
Date
Description
0
1
20-Dec-2013
5-Mar-2014
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-50F / +600F
-46C / 316C
None
2160 psig
148.9 barg
Pipe
1/2"
Sch
Ends
3/4"
1"
Sch 80S
1-1/2"
2"
3"
4"
Sch 40S
6"
8"
Plugs (Note 6)
12"
OB
SB
GD
GD
16"
Sch 80
18"
20"
24"
Sch
Flanges Rating
Matl
Fittings
Unions
10"
SR
SR
Service
Sch 80S
Matl
Rating
Pipe Size
Specification
600# RF SW (Note 2)
Couplings
3000# FS, Full, Threaded, A-182-F316
Nipples (thd x thd)
Sch 80S smls A-312-TP316
Nipples (PE x thd)
Sockolets
Threadolets
Weldolets
Gaskets
Bolting
VALVES
(Notes 4, 6)
Washers, 316SS
Gate
Ball (5)
Globe
D1R-SN
Check
D5S-SN, D5Z-SN
B utterfly (5)
Needle
G6S-SN, G9S-SN
Notes: 1 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
Temp F
PSIG
Temp C
BAR
-50 to 100
200
1440
1240
-46 to 38
50
99.3
96.2
4 Where materials are shown to be dual certified, materials may be supplied dual certified for 316 / 316L,
or may be certified for 316 with chemistry that meets 316L.
300
1120
100
84.4
400
1025
150
77
5 Valves with elastomer seats and/or seals may not be rated for full ANSI pressure-temperature values.
Refer to P&ID's and/or Equipment Data Sheets for system uppler limit design temperature.
500
600
955
900
200
250
71.3
66.8
650
885
300
63.2
700
750
870
855
325
350
61.8
60.7
8 Seamless pipe and weld fittings may be substituted for ERW pipe and weld fittings.
800
845
375
59.8
400
58.9
425
58.3
3/4
1/2
SWT
SWTS
SWT
BRANCH SIZE
HEADER SIZE
24
24
WT
20
18
16
14
12
10
20
WRT
WT
18
WRT
WRT
WT
16
14
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
12
WRT
WRT
WRT
WRT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
8
6
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWT
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
Specification
D06
Document No
Revision
Date
Description
0
1
20-Dec-2013
5-Mar-2014
SR
SR
OB
SB
GD
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-20F / +400F
-29C /204C
None
2250 psig
155.1 barg
Pipe Size
Pipe
1/2"
Sch
Ends
3/4"
1"
Sch 80S
1-1/2"
600# RF SW
3000# FS, A-182-F51 (Note 7)
3000# FS, SW, A-182-F51 (Note 7)
Plugs
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
8"
10"
12"
14"
Sch 80S
16"
18"
20"
Sch 80
24"
Unions
4"
6"
Sch 40S
Matl
Fittings
3"
Matl
Sch
Flanges Rating
2"
600# RFWN
ASTM A-182-F51
Seamless, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Bolting
VALVES
(Notes 4, 6)
Gate
Ball (5)
Globe
Check
B utterfly (5)
Needle /
Gauge
Temp F
-20 to 100
200
PSIG
1500
1490
Temp C
-29 to 38
50
BAR
103.4
103.4
300
1335
100
101.3
400
500
600
1230
1160
1115
150
200
250
91.9
85.3
80.9
300
77.7
325
76.3
3/4
1/2
SWT
SWTS
SWT
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
24
20
WT
WRT
WT
18
16
WRT
WRT
WRT
WRT
WT
WRT
WT
14
12
10
WRT
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WOL
WOL
6
4
3
WOL
WOL
WOL
WOL
WOL
WOL
10
WT
WRT
WRT
WT
WRT
WT
1 1/2
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
SWT Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWTS
WT
SWTS
SWTS
Butt Weld Tee
SWT
PIPING SPECIFICATION - ASME CLASS 600, 2205 DUPLEX STAINLESS STEEL (NACE)
Specification
D06N
Document No
Revision
Date
Description
0
1
20-Dec-2013
5-Mar-2014
SR
SR
OB
SB
GD
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-20F / +400F
-29C /204C
None
2250 psig
155.1 barg
Pipe Size
Pipe
1/2"
Sch
Ends
3/4"
1"
Sch 80S
1-1/2"
600# RF SW
3000# FS, A-182-F51 (Note 7)
3000# FS, SW, A-182-F51 (Note 7)
Plugs
Couplings
Sockolets
Threadolets
Weldolets
Gaskets
8"
10"
12"
14"
Sch 80S
16"
18"
20"
Sch 80
24"
Unions
4"
6"
Sch 40S
Matl
Fittings
3"
Matl
Sch
Flanges Rating
2"
600# RFWN
ASTM A-182-F51
Seamless, ASTM A-815-UNS S31803 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Bolting
B utterfly (5)
Needle
G6S-XN, G9S-XN
VALVES
(Notes 4, 6)
Gate
Ball (5)
Globe
Check
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
Temp F
-20 to 100
200
PSIG
1500
1490
Temp C
-29 to 38
50
BAR
103.4
103.4
300
1335
100
101.3
400
500
600
1230
1160
1115
150
200
250
91.9
85.3
80.9
300
77.7
325
76.3
3/4
1/2
SWT
SWTS
SWT
HEADER SIZE
BRANCH SIZE
24
20
18
16
14
12
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WOL
WRT
WRT
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
24
20
WT
WRT
WT
18
16
WRT
WRT
WRT
WRT
WT
WRT
WT
14
12
10
WRT
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
WOL
WOL
6
4
3
WOL
WOL
WOL
WOL
WOL
WOL
10
WT
WRT
WRT
WT
WRT
WT
1 1/2
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS Full size SW Tee with Swage
SOL
Sockolet
WOL Weldolet
SWT Socket Weld Tee
TOL
Threadolet
WRT Butt Weld Reducing Tee
SWTS
WT
SWTS
SWTS
Butt Weld Tee
SWT
Specification
PIPING SPECIFICATION - ASME CLASS 600, 2507 SUPER DUPLEX STAINLESS STEEL
D08
Document No
Revision
0
1
Date
20-Dec-2013
5-Mar-2014
Description
Cameron standard - Issued for Design
Revise Pipe Sch, Nipples, Swages
SB
GD
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
Service
ASME B31.3
-20F / +600F
-29C / 316C
None
2250 psig
155.1 barg
Pipe Size
Pipe
1/2"
Sch
Ends
Matl
Sch
Flanges Rating
Matl
Fittings
3/4"
1"
Sch 80S
1-1/2"
2"
3"
4"
6"
8"
Sch 40S
10"
12"
14"
16"
18"
Sch 80S
20"
24"
Sch 80
600# RF SW
600# RFWN
ASTM A-182-F53
Seamless, ASTM A-815-UNS S32750 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Unions
Plugs
Couplings
Nipples (thd x thd)
Nipples (PE x thd)
Swages
(PE both ends)
(Note 7)
Sockolets
Threadolets
Weldolets
Gaskets
VALVES
Bolting
Gate (4)
Ball (4,5)
D2R-X, D2RF-X
D4R-X
D5R-X, D5RG-X, D5RW-X
D7RG-X, D7RW-X
B utterfly (5)
Needle /
Gauge
G6S-X, G9S-X
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thickness.
2 Not applicable
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Temp F
-20 to 100
200
PSIG
1500
1490
Temp C
-29 to 38
50
BAR
103.4
103.4
300
400
500
1335
1230
1160
100
150
200
101.3
91.9
85.3
600
1115
250
300
325
80.9
77.7
76.3
1 1/2
3/4
1/2
SWT
SWTS
SWTS
SWT
SWTS
SWT
BRANCH SIZE
8 Welded construction to be used for in-line process piping. Threaded connections are permitted for
instrument take-offs, piping vent and drain valves
HEADER SIZE
24
WT
20
18
24
16
14
12
20
18
16
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
14
12
10
WRT
WRT
WOL
WRT
WRT
WRT
WRT
WRT
WRT
8
6
4
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
10
WRT
WRT
WRT
WT
WRT
WRT
WT
WRT
WT
WRT
WOL
WOL
WRT
WOL
WOL
WRT
WRT
WOL
WRT
WRT
WOL
WT
WRT
WRT
WT
WRT
WT
3
2
1 1/2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
TOL
Sockolet
Threadolet
WOL
WRT
Weldolet
Butt Weld Reducing Tee
WT
Specification
PIPING SPEC - ASME CLASS 600, 2507 SUPER DUPLEX STAINLESS STEEL (NACE)
D08N
Document No
Revision
Date
0
1
20-Dec-2013
5-Mar-2014
Description
Rating
Piping Code
Material / Group
Temp Range
Corrosion
Allowance
Hydrotest
Pressure
ASME B31.3
-20F / +600F
-29C / 316C
None
2250 psig
155.1 barg
Pipe Size
Pipe
1/2"
Sch
3/4"
1"
Sch 80S
Ends
1-1/2"
2"
3"
Prepared Checked
4"
6"
8"
Sch 40S
10"
12"
SR
SR
OB
SB
Service
Liquids and Vapors - General Process
14"
16"
18"
Sch 80S
20"
Flanges Rating
600# RF SW
600# RFWN
Matl
Fittings
ASTM A-182-F53
Seamless, ASTM A-815-UNS S32750 Class WP-S, Butt Weld, Bore to match pipe (Note 3)
Unions
Plugs
Couplings
24"
Sch 80
Matl
Sch
Approved
GD
GD
Swages
(PE both ends)
(Note 7)
Sockolets
Threadolets
Weldolets
Gaskets
Gate (4)
VALVES
Ball (4,5)
B utterfly (5)
Needle /
Gauge
D2R-XN, D2RF-XN
D4R-XN
D5R-XN, D5RG-XN, D5RW-XN
D7RG-XN, D7RW-XN
G6S-XN, G9S-XN
Notes: 1 -20 / 100F pressure rating is used to determine the required pipe wall thicknes s.
2 Not applicable
Temp F
Temp C
BAR
3 Butt weld reducing fittings shall be purchased to the heavier pipe schedule.
Piping drawing notes will indicate where internal beveling is required
-20 to 100
200
1500
1490
-29 to 38
50
103.4
103.4
300
1335
100
101.3
400
500
1230
1160
150
200
91.9
85.3
6 Not applicable
7 Beveled end of swages are to be tapered to match bore of pipe for welding.
8 Welded construction to be used for in-line process piping. Threaded connections are permitted for
600
1115
250
80.9
300
325
77.7
76.3
3/4
1/2
BRANCH SIZE
24
20
18
16
14
12
10
24
WT
20
18
WRT
WRT
WT
WRT
WT
16
WRT
WRT
WRT
WT
14
12
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WRT
WT
WRT
WT
10
WOL
WRT
WRT
WRT
WRT
WRT
WT
8
6
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WOL
WRT
WRT
WRT
WRT
WT
WRT
WT
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WRT
WT
3
2
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WOL
WRT
WOL
WRT
WRT
WT
WRT
WT
1 1/2
1 1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWT
1
3/4
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWT
SWTS
SWT
1/2
SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL SOL/TOL
SWTS
SWTS
SWTS
SWTS
SWT
SOL
Sockolet
WOL
Weldolet
TOL
Threadolet
WRT
WT
SWT