Professional Documents
Culture Documents
d POE2000 pendulum
impact test machine
Features
Pendulum Arm
Rigid bifurcated, accurate arm geometry,
fabricated from aircraft quality aluminum
alloy. Balance, alignment and center of
percussion are constantly maintained at
center of strike throughout each of the
seven energy ranges. Precision integration of
the tup allows for easy installation and
removal. The design allows for recessed
anvils and offers freedom from jamming of
broken specimens.
Base System
Standard Specifications
Pendulum: One-arm design,
nominal* base capacity: 24 in-lbs
(2 ft-lbs or 2.7 J)
*These are nominal values. The machine can
be adjusted to meet exact ISO specifications.
h
Velocity
11.48 ft/s (3.5 m/s) at 2 ft elevation and
adjustable depending on chosen angle
of fall.
Installation Specifications
and Requirements
h
Dimensions:
- Height: 23 in (0.5842 m)
- Width: 12 in (0.3048 m)
- Length: 16 in (0.4064 m)
Options
h Additional weights for model POE2000
pendulum impact test machine increase
energy to:
- 4 ft-lbs (5.42 J)
- 5.5 ft-lbs (6.8 J), 8 ft-lbs (10.8 J)
- 11 ft-lbs (14.9 J), 16 ft-lbs (21.6 J)
- 18.4 ft-lbs (24.9 J) 36.9 ft-lbs (50 J).
h
PC computer
TM
Izod Testing
The BLI is set up for standard Izod specimen
testing. The machine features a 2.7 J
(2 ft-lbs) Izod pendulum that can be
increased to 5.4 J (4 ft-lbs), 10.8 J (8 ft-lbs)
and 21.7 J (16 ft-lbs) by adding optional
calibrated weight sets for each capacity. A
separate pendulum is available for testing at
1.3 J (1 ft-lbs) capacity.
Charpy Testing
The BLI is fitted to Charpy testing using
optional Charpy pendulums, specimen
supports and anvils. Charpy pendulums of
1.3 J (1 ft-lbs), 2.7 J (2 ft-lbs), 5.4 J (4 ft-lbs),
10.8 J (8 ft-lbs) and 21.7 J (16 ft-lbs) are
available. The Charpy anvils and specimen
holders are secured to the inside and front
faces of the vertical frame elements, and may
be left in place when the machine is used for
Izod testing. Changeover from Izod to Charpy
is simple and requires no special skills.
Specimen-In-Hand
Tensile Impact Testing
The BLI can be adapted to tensile impact
testing with the addition of optional tension
impact pendulums and anvils. In operation,
the specimen is positioned in the striking head
of the pendulum. The specimen is clamped at
one end to the forward vise and at the other
end to a detachable crosshead. When the
pendulum is released, the specimen is broken
by the force exerted from the crosshead
meeting the contact legs of the anvil. The
energy required to fracture the specimen is
read from the dial.
Contoured specimens 63.5 mm (2.5 in) long
by 9.525 mm (0.37 in) wide and up to
3.175 mm (0.125 in) thick can be tested. As
with the Izod pendulum, the 2.7 J (2 ft-lbs)
capacity of the tensile impact pendulum can
be increased to 5.4 J (4 ft-lbs), 10.8 J (8 ft-lbs)
or 21.7 J (16 ft-lbs) by adding weight sets for
each capacity. For testing at 1.3 J (1 ft-lbs)
capacity, a separate pendulum is used.
Also Supported
h
Specifications
MACHINE HEIGHT
732 mm (28.1875)
Machine Width
Machine Depth
TM
Also Supported
h
h
d Control lever
(latch, release, brake)
d Charpy striker
d Izod striker
5
d The SI-1 impact tester
Capacity:
- 33.9 J (25 ft-lbs) when pendulum
is released from low latch position
- 81.3 J (60 ft-lbs) when released
from the high latch position
Model SI-1D3
h
Model SI-1B
h
Model SI-1C3
Capacity:
-169.5 J (125 ft-lbs) from the low
latch position
- 406.7 J (300 ft-lbs) from the high
latch position
Model SI-1K3
h
Capacity:
- 169.5 J (125 ft-lbs) from the low
latch position
- 406.7 J (300 ft-lbs) from the high
latch position
SI-1 Specifications
WEIGHT AT STRIKER
Light Pendulum
Light Pendulum with Weight Attached
Heavy Pendulum
Length of Pendulum
Floor Space Requirements
Net Weight
Overall Height Requirements
HEIGHT OF DROP
Low Latch
High Latch
IMPACT VELOCITY
Low Latch
High Latch
Charpy Span
Shipping Dimensions
Shipping Weight
Easy Set-Up
Push buttons guide you through five display
modes that prompt for setup information.
Choose from a selection of programmed
hammer weights, including model and serial
number for identification of each.
Trilingual Display
Specifications
Type
Resolution
Accuracy
Repeatability
Power Requirements
Dimensions (WxHxD)
Software
Electronics
For information on Instron products and services call your local worldwide sales, service and technical support offices:
Corporate Headquarters
Instron Corporation
825 University Ave
Norwood, MA 02062-2643 USA
Tel: +1 800 564 8378
+1 781 575 5000
Fax: +1 781 575 5751
European Headquarters
Instron Limited
Coronation Road
High Wycombe, Bucks
HP12 3SY United Kingdom
Tel: +44 1494 464646
Fax: +44 1494 456814
IST GmbH
Landwehrstrasse 65
Darmstadt, D-64293 Germany
Tel: +49 6151 3917-0
Fax: +49 6151 3917-500
USA
CANADA
Toronto
Brazil
Sao Paulo
Tel: +55 11 4195 8160
Caribbean, Mexico, South America
and Central America
Canton
Tel: +1 781 821 2770
EUROPE
ASIA
China
Beijing
Shanghai
ndia
In
Chennai
Japan
Tokyo
Osaka
Nagoya
Korea
Seoul
Singapore
Taiwan
Hsinchu
Thailand
Bangkok
AUSTRALIA
Melbourne
www.instron.com
Instron is a registered trademark of Instron Corporation.
Other names, logos, icons and marks identifying Instron products and services referenced herein are trademarks of Instron Corporation and
may not be used without the prior written permission of Instron.
Other product and company names listed are trademarks or trade names of their respective companies.
Copyright 2005 Instron Corporation. All rights reserved.
All of the specifications shown in this brochure are subject to change without notice.
WB1213