You are on page 1of 6

Set PS User Inactive Detecting Timer(SET UPSINACTTIMER)

Function
Use this command to set PS user inactive detecting timer.

Note
None

Parameters
Parameter ID

Parameter Name

PsInactTmrForCon

Conversational
service T1

ProtectTmrForCon

Conversational
service T2

Parameter Description
Meaning: When detecting that the Ps' Conversational
User had no data to transfer for a long time which
longer than this timer, the PDCP layer would request
the RRC layer to release this Radio Access Bear.
GUI Value Range: 0~14400
Unit: s
Actual Value Range: 0~14400
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure conversational services,
the related T1 and T2 must be 0 at the same time. 2.
For the detection timers that need to configure
conversational services, the related T1 and T2 must
not be 0 at the same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None
Meaning: After sending release request to RRC layer, if
the Conversational Radio Access Bear haven't been
released until the Conversational service T2 timeout,
the PDCP layer will resend release request indication.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure conversational services,
the related T1 and T2 must be 0 at the same time. 2.
For the detection timers that need to configure
conversational services, the related T1 and T2 must
not be 0 at the same time.
Service Interrupted After Modification: No (And no

Parameter ID

Parameter Name

Parameter Description
impact on the UE in idle mode)
Impact on Network Performance: None

PsInactTmrForStr

Streaming service Meaning: When detecting that the Ps' Streaming User
T1
had no data to transfer for a long time which longer
than this timer, the PDCP layer would request the RRC
layer to release this Radio Access Bear.
GUI Value Range: 0~14400
Unit: s
Actual Value Range: 0~14400
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure streaming services, the
related T1 and T2 must be 0 at the same time. 2. For
the detection timers that need to configure streaming
services, the related T1 and T2 must not be 0 at the
same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

ProtectTmrForStr

Streaming service Meaning: After sending release request to RRC layer, if


T2
the Streaming Radio Access Bear haven't been
released until the Streaming service T2 timeout, the
PDCP layer will resend release request indication.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure streaming services, the
related T1 and T2 must be 0 at the same time. 2. For
the detection timers that need to configure streaming
services, the related T1 and T2 must not be 0 at the
same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

PsInactTmrForInt

Interactive service Meaning: When detecting that the Ps' Interactive User
T1
had no data to transfer for a long time which longer
than this timer, the PDCP layer would request the RRC
layer to release this Radio Access Bear.
GUI Value Range: 0~14400

Parameter ID

Parameter Name

Parameter Description
Unit: s
Actual Value Range: 0~14400
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure interactive services, the
related T1 and T2 must be 0 at the same time. 2. For
the detection timers that need to configure interactive
services, the related T1 and T2 must not be 0 at the
same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

ProtectTmrForInt

Interactive service Meaning: After sending release request to RRC layer, if


T2
the Interactive Radio Access Bear haven't been
released until the Interactive service T2 timeout, the
PDCP layer will resend release request indication.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure interactive services, the
related T1 and T2 must be 0 at the same time. 2. For
the detection timers that need to configure interactive
services, the related T1 and T2 must not be 0 at the
same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

PsInactTmrForBac

Background
service T1

Meaning: When detecting that the Ps' Background


User had no data to transfer for a long time which
longer than this timer, the PDCP layer would request
the RRC layer to release this Radio Access Bear.
GUI Value Range: 0~14400
Unit: s
Actual Value Range: 0~14400
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure background services, the
related T1 and T2 must be 0 at the same time. 2. For
the detection timers that need to configure background
services, the related T1 and T2 must not be 0 at the

Parameter ID

Parameter Name

Parameter Description
same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

ProtectTmrForBac

Background
service T2

Meaning: After sending release request to RRC layer, if


the Background Radio Access Bear haven't been
released until the Background service T2 timeout, the
PDCP layer will resend release request indication.
GUI Value Range: 0~60
Unit: s
Actual Value Range: 0~60
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure background services, the
related T1 and T2 must be 0 at the same time. 2. For
the detection timers that need to configure background
services, the related T1 and T2 must not be 0 at the
same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

PsInactTmrForPreFstDrm

FAST
DORMANCY
USER T1 in
CELL_PCH

Meaning: This parameter specifies the value of the


CELL-PCH inactivity timer for UEs enabled with the
Fast Dormancy feature. When detecting that the Fast
Dormancy User in PS domain had no data to transfer
in CELL-PCH for a long time which longer than this
timer, the UE is released. To enable this timer, set this
timer to a value other than 0.
GUI Value Range: 0~64800
Unit: s
Actual Value Range: 0~64800
MML Default Value: None
Recommended Value: 360
Parameter Relationship: None
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

ProtectTmrForImsSig

IMS signal T2

Meaning: After sending release request to RRC layer, if


the IMS Radio Access Bear for signal haven't been
released until the IMS service T2 timeout, the PDCP
layer will resend release request indication.
GUI Value Range: 0~60

Parameter ID

Parameter Name

Parameter Description
Unit: s
Actual Value Range: 0~60
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure IMS signaling services,
the related T1 and T2 must be 0 at the same time. 2.
For the detection timers that need to configure IMS
signaling services, the related T1 and T2 must not be 0
at the same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

PSInactTmrForImsSig

IMS signal T1

Meaning: When detecting that the Ps' IMS signal had


no data to transfer for a long time which longer than
this timer, the PDCP layer would request the RRC
layer to release this Radio Access Bear.
GUI Value Range: 0~64800
Unit: s
Actual Value Range: 0~64800
MML Default Value: None
Recommended Value: 20
Parameter Relationship: 1. For the detection timers
that do not need to configure IMS signaling services,
the related T1 and T2 must be 0 at the same time. 2.
For the detection timers that need to configure IMS
signaling services, the related T1 and T2 must not be 0
at the same time.
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

PsInactTmrForFstDrmDch

FAST
DORMANCY
USER T1 in
CELL_DCH

Meaning: Timer for FD-enabled UEs or LTE-enabled


UEs staying in the CELL_DCH state. When UEs that
are enabled with Fast Dormancy (FD) and stay in the
CELL_DCH state do not transmit any data after this
timer expires, the RNC transits the UEs to the
CELL_FACH or CELL_PCH state. When LTE-enabled
UEs in the CELL_DCH state do not transmit any data
after this timer expires, the RNC transits the UEs to the
CELL_PCH or IDLE state. You can set this timer to a
value other than 0 if you want to check whether FDenabled UEs and LTE-enabled UEs are in the
CELL_DCH state.
GUI Value Range: 0~64800
Unit: s

Parameter ID

Parameter Name

Parameter Description
Actual Value Range: 0~64800
MML Default Value: None
Recommended Value: 4
Parameter Relationship: None
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

PsInactTmrForFstDrmFac
h

FAST
DORMANCY
USER T1 in
CELL_FACH

Meaning: Timer for FD-enabled UEs or LTE-enabled


UEs staying in the CELL_FACH state. When UEs that
are enabled with Fast Dormancy (FD) and stay in the
CELL_FACH state do not transmit any data after this
timer expires, the RNC transits the UEs to the
CELL_PCH state. When LTE-enabled UEs in the
CELL_FACH state do not transmit any data after this
timer expires, the RNC transits the UEs to the
CELL_PCH or IDLE state. You can set this timer to a
value other than 0 if you want to check whether FDenabled UEs and LTE-enabled UEs are in the
CELL_FACH state.
GUI Value Range: 0~64800
Unit: s
Actual Value Range: 0~64800
MML Default Value: None
Recommended Value: 10
Parameter Relationship: None
Service Interrupted After Modification: No (And no
impact on the UE in idle mode)
Impact on Network Performance: None

Example
Set the PS' user inactive detecting timer:
Interactive service T1 = 4 minutes, Interactive service T2 = 10 seconds.
Background service T1 = 4 minutes, Background service T2 = 10 seconds.
Conversational service T1 = 4 minutes, Conversational service T2 = 10
seconds.
Streaming service T1 = 4 minutes, Streaming service T2 = 10 seconds.
Fast Dormancy T1 = 360 seconds.
IMS signal T1 = 60 minutes, IMS signal T2 = 10 seconds.
SET UPSINACTTIMER:PsInactTmrForInt=240, ProtectTmrForInt=10,
PsInactTmrForBac=240, ProtectTmrForBac=10, PsInactTmrForCon=240,
ProtectTmrForCon=10,PsInactTmrForStr=240, ProtectTmrForStr=10,
PSInactTmrForImsSig=3600, ProtectTmrForImsSig=10;

You might also like