Professional Documents
Culture Documents
OWNER'S MANUAL
www.skpaudio.com
Contents
Safety Instructions
warning
Important Safety Instructions
1
1
Applications
Features
2
2
Quickstart
Connectors
Switches
Mix/Loop
Controls
Indicators
4
4
5
5
6
Changing Voltage
Fuse Replacement
6
6
Application Examples
8
8
Reference
9
10
11
Block Diagram
11
Troubleshooting
Specifications
Frequency Response
12
14
14
Safety Instructions
SK-6P
Safety Instructions
WARNING
CAUTION
CAUTION
AVIS
ATTENTION
UTILISER UN FUSIBLE DE
RECHANGE DE MEME TYPE
WARNING: To reduce the risk of fire or electric shock, do not expose this unit to rain or moisture. To reduce the hazard of
electrical shock, do not remove cover or back. No user serviceable parts inside. Please refer all servicing to
qualified personnel. The lightning flash with an arrowhead symbol within an equilateral triangle, within the
products enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The
exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating
and maintenance (servicing) instructions in the literature accompanying the product.
SK-6P
Features
Of one of the most successful and influential professional speaker systems ever.
15"Differential Drive R low-frequency driver with dual neodymium magnet for low-distortion and light weight.
Built in 3-input mixer. One balanced mic/line input, two 1/4" phone line-level inputs. Two-band equalization.
Balanced loop - through / mix output. "Daisy-chain" additional SK-6P speakers or send the mixed output
to a mixing console.
Thermomaster R Total Thermal Management SystemR . A single piece, cast-aluminum baffle integrates the woofer
frame, horn, and amplifier heat-sink. Air movement in the finned ports dissipates heat - no internal or external
cooling fans are required.
Rugged, light-weight, black co-polymer enclosure with cast aluminum baffle.
Integral 35mm pole mount receptacle with securing thumb screw.
Multi-angle enclosure for front of house or stage monitor application.
Tailored dynamic processing protects amplifiers and speakers from being over-driven without producing extreme
changes in frequency response as level varies.
Extended low-frequency performance. Delivers powerful bass down to 40Hz.
QUICKSTART
SK-6P
QUICKSTART
1. Turn the INPUT 1,2,and 3 controls fully counter-clockwise.
2. Set the MIC/LINE switch.
If a microphone will be connected directly to INPUT 1, set the MIC/LINE position (disengaged). The MIC LED will
not illuminate when power is turned on.
If a mixer, CD player, cassette tape, or electronic musical instrument (the "source")will be connected directly to
INPUT 1, set the MIC/LINE switch to the LINE position (disengaged). The MIC LED will not illuminate when power
is turned on.
3. Set the EQ HF and LF controls to their center detented position.
4. Plug the power cable into a properly grounded 3-wire AC power.
5. Plug the XLR cable from the mixer or microphone into the INPUT 1 connector.
6. Connect unbalanced sources (if used) to the LINE2 and LINE 3 input connectors.
7. POWER UP PROCEDURE
First, switch on the power to the mixer, audio sources, or musical instruments that are feeding your SK-6P
Next, turn on the power switch (the front panel power indicator will illuminate).
Reverse this process when shutting down your system.
8.SET VOLUME
If you are using an audio mixing console, refer to the manufacturer's instructions to properly set gain structure.
Turn up your sources to the level that will be used in performance and talk, sing or play into the system.
Bring the INPUT 1 control up (clockwise) until the desired volume has been reached. If you are using a micro
phone, turn the INPUT 1 control up slowly to avoid feedback.
If you are using the INPUT 2 and INPUT 3 inputs, bring the INPUT 2 controls up until the desired volume has
been reached.
9.CHECK THE PEAK LED
The PEAK indicator flashes when the loudspeaker's on-board amplifier are approaching maximum output.
Occasional flashes are normal for very loud operation, However, if the PEAK LED stays illuminated, the
sound may be distorted and it is an indication that more speakers or a lower performance volume may be
required for your specific application.
SK-6P
LOOP
MIX
Connectors
OUTPUT
INPUT 1
This balanced input accepts a standard XLR ( female ) connector. A
broad range of signals (-44 dBu to +20 dBu nominal) from microphones, audio mixing consoles,and electronic musical instruments maybe connected here. When using a single audio input to the speaker,
this is the input to use.The sensitivity of this input is controlled by the
MIC/LINE SWITCH and the INPUT 1 rotary control.
INPUT1
HIGH
LINE
MIC
INPUT 1
VOL
PEAK
MIN
MAX
INPUT 2
VOL
MIN
OUT
This XLR(male)output connector works with the MIX/LOOP SWITCH
toprovide a method of sending audio from your SK-6P.
MAX
INPUT 3
VOL
INPUT2
MIN
MAX
INPUT3
HF
-15dB
+15dB
EQ
LF
SIGNAL
-15dB
+15dB
Switches
MIC/LINE
The MIC/LINE switch effects only INPUT 1. It selects between two
sensitivity ranges. This switch is used to match the input sensitivity
of the SK-6P with the output level of the device connected to INPUT1.
Depressing the MIC/LINE switch selects MIC (most sensitive).
CAUTIO N: Before adjusting this switch, be certain to rotate the INPUT1
control fully counter-clockwise. After the MIC/LINE switch has been
adjusted,slowly rotate the INPUT1 control clock-wise until the desired
volume has been reached.
SK-6P
MIX/LOOP
This switch selects the source of the signal, for the OUT connector.
CAUTION: Before adjusting this switch, be certain to set the input level control of any equipment connected to this
output to its minimum gain (least sensitive) setting.
In the disengaged position, only the signal from the INPUT1 connector is routed directly to the OUT connector. Changing the other settings on the audio panel will not effect the OUT signal. The INPUT 2 and INPUT 3 inputs will not be
present at the OUT connector. Use this setting when you want to feed multiple SK-6P powered speakers the same
signal.
In The MIX position (depressed), a post-EQ blend of all inputs to the speaker(INPUT1,2, and 3)will be sent to the OUT
connector, Any changes to input level settings or EQ will affect the OUT signal, See the SYSTEM EXAMPLES section
for details on how this mode may be used.
Controls
INPUT 1
Adjusts the level of INPUT 1. Use this control to match the input sensitivity of the SK-6P to the output level of the mixer,
microphone,or instrument connected to INPUT1.It is a common misconception that this control changes the power of a
system. Your SK-6P will produce its rated output power no matter where this control is Jset. The INPUT 1 control
Determines how much signal is required at the input in order to drive the system to full output.
INPUT 2 & INPUT 3
These controls adjust the level of the inputs connected to INPUTS 2 and 3.
LF EQ
This control allows up to 15dB of cut or boost at 75 Hz. If the system seems too "boomy" or bass heavy, rotate this control counter clock-wise. If the system sounds too "thin" or lacks low-end power, rotate this control clock-wise. To set the
low-frequency EQ to "flat" (no EQ cut or boost), set this control to the center detented position.
HF EQ
This control allows up to 15dB of cut or boost at 30KHz. If the system seems too "strident" or "tinny", rotate this control
counter clock-wise. If the system sounds too "dark" or lacks "brilliance", rotate this control clock-wise. To set the lowfrequency EQ to "flat" (no EQ cut or boost), set this control to the center detented position.
SK-6P
INDICATORS
PEAK
The PEAK LED (Light Emitting Diode) illuminates to indicate that the system is approaching clipping. The threshold for this
light is actually about 2 dB below clipping. An occasional flickering of this light on the loudest peaks is acceptable. If this
LED is on for more than the duration of brief dynamic peaks, the system is being overdriven. Continuously over-driving the
system will result in unpleasant and fatiguing distortion and may lead to premature failure of your speaker system. If the
PEAK LED illuminates excessively:
Reduce INPUT 1, 2, and 3.
Reduce the output level of the mixer, musical instrument, or other source connected to the speaker.
If there is a great deal of LF EQ or HF EQ boost, return the controls to the "flat" (centered) position.
SIGNAL
illuminates to indicate a usable signal from INPUT 1.
MIC
This LED lights to indicate that the MIC/LINE switch is in the MIC (depressed) position.
Fuse Replacement
The SK-6P has no user-serviceable fuses. Failure of fuses is most frequently a symptom of problems requiring service by
a competent technician.
APPLICATION EXAMPLES
SK-6P
APPLICATION EXAMPLES
Li v e Band PA Sy s t e m Wi t h Mo ni t o r s
This example shows a typical PA system using mixer with a pair of SK-6P for the main left and right mix. A separate
signal from the mixer's AUX/MONITOR bus is sent to two additional SK-6P placed in the tilt-back, wedge positions for
use as floor monitors.
APPLICATION EXAMPLES
SK-6P
INPUT 1
INPUT 1
DJ Mixer
Output-Right
Output-Left
Electronic
Crossover
Amplifier
Synthesizer
OUT
INPUT 1
INPUT 2
INPUT 3
Sampler
To Mixing Console
REFERENCE
SK-6P
REFERENCE
Connections - Balanced and Unbalanced
There are two basic types of audio system interconnections for audio signals: Balanced and Unbalanced. Your
SK-6P can accept either type of input.
Balanced Lines
In audio, a balanced line is a three-conductor system in which the two signal wires carry an equal, but opposite
voltage with respect to the ground wire. The ground wire acts only as a shield and does not carry any audio signal
current. Outside interference (such as RFI-Radio Frequency Interference) is either shielded from the internal signal
conductor, or if it gets into the cable is cancelled out by the opposite signals at the receiving end. Balanced
connections are preferred for any longer cable runs.
Unbalanced Lines
Unbalanced cable is a two-wire system where the shield (ground wire) acts as one of the current carrying signal
conductors. The center conductor enclosed by the shield is commonly known as the "hot" conductor. Unbalanced
audio cables do not reject noise as well as balanced lines. Unbalanced lines are typical in home hi-fi type systems
and on the outputs of electronic musical instruments. These work well if the distance between the components is
short, the signal level is relatively high and all of the electronics used in the system are same AC service.
Unbalanced Sources to SK-6P Powered Loudspeakers
If you need to connect your SK-6P speakers to an unbalanced source you have two options:
Use the LINE 2 and LINE 3 connectors. These inputs are balanced but will accept unbalanced inputs without the
need for any special adapters.
Use an adapter or special cable (see the section "Cables and Connectors")
REFERENCE
SK-6P
The standard cable for interconnection of microphone and line level signal in professional audio systems.
Microphone to mixer
Microphone to SK-6P INPUT 1
Professional audio mixer to SK-6P INPUT 1
"Daisy chaining" SK-6P speaker systems
For connecting balanced devices with 1/4" connector to SK-6P XLR input.
Connects consumer audio products and some DJ mixer outputs to professional audio equipment inputs.
Connects outputs of consumer audio equipment to unbalanced line inputs of SK-6P and mixers
Connects unbalanced line outputs to many mixers to the inputs of consumer audio recorder.
Used to "telescope" a ground to eliminate hum caused by "ground loops". For use only with balanced
inputs and outputs.
1
2
3
1 (shield)
2
3
Tip
Ring
Sleevee
1 (shield)
2
3
Tip
Ring
Sleevee
1 (shield)
2
3
Tip
1 (shield)
2
3
Center
Shield
Center
Sleeve (shield)
Tip
Sleeve (shield)
Tip
Sleeve (shield)
10
1 (no connection)
2
3
BLOCK DIAGRAM
SK-6P
BLOCK DIAGRAM
LOOP
MIX
PEAK
OUT
INPUT 1
SIGNAL
INPUT 1
LINE
MIC
EQ
SUM
LOW HIGH
MIC
INPUT 2
INPUT 2
INPUT 3
INPUT 3
11
HPF
90W
LPF
&
DYNAMIC
FILTER
300W
TROUBLESHOOTING
SK-6P
TROUBLESHOOTING
Symptom
No sound
Likely Cause
Speaker not connected to active
AC power
Blown fuse
What to do
power
12
TROUBLESHOOTING
SK-6P
Hum or Buzz
Excessively long unbalanced cable
run
Excessive gain
13
SK-6P
MANUAL DEL PROPIETARIO
www.skpaudio.com
Contenido
Instrucciones de seguridad
Advertencia
Instrucciones de seguridad importanes
Sobre el SK-6P
1
1
1
Aplicaciones
Caracter sticas
2
2
2
Comienzo r pido
Controles y conextiones
4
4
4
5
5
6
Conectores
Interruptores
Mezcla/bucle
Controels
Indicadores
Ejemplos de aplicaciones
Sistema DJ con amplificador de bajos (subwoofer) pasivo
Mezclador y amplificador de teclado
Referencia
6
6
6
7
8
8
9
9
10
11
Diagrama de bloque
11
Soluci n de problemas
Especificaciones
Respuesta de frecuencia
12
14
14
INSTRUCCIONES DE SEGURIDAD
SK-6P
Instrucciones de seguridad
ADVERTENCIA
NO EXPONGA ESTE
EQUIPO
ALA LLUVIA O HUMEDAD
AVISO
RIESGO DE DESCARGA
ELECTRICA-NO ABRIR
PRECAUCION
PARA UNA PROTECCION
CONTINUA CONTRA
RIESGO DE FUEGO
REEMPLACE SOLO CON EL
MISMO TIPO DE FUSIBLE
PRECAUCION
RIESGO DE DESCARGA
ELECTRICA-NO ABRIR
ADVERTENCIA: Para reducir el riesgo de incedio o descarga el ctrica, no exponga este equipo a la lluvia o humedad.
Para reducir el peligro de descarga el ctrica, no quite la cubierta o la parte trasera. No guarde repuestos
dentro del equipo.Utilice un servicio t cnico con personal calificado.El s mbolo del rel mpago con una
punta de flecha dentro de un triangulo equil tero en el envase de un producto significa que puede la
descarga el ctrica puede ser de suficiente magnitud como para constituir un riesgo para las personas.
El signo de exclamaci n dentro de un triangulo equil tero intenta alertar al usuario de la presencia de
~ el producto.
instrucciones importantes de mantenimiento y operaci n en la manual que acompana
SOBRE EL SK-6P
SK-6P
SBORE EL SK-6P
Aplicaciones
Refuerzo de sonido en vivo, discurso y vocalizaci n, reproducci n de m sica en entretenimiento, A/V, y
establecimientos institucionales especialmente cuando la facilidad de uso y la portabilidad son factores importantes .
Amplificaci n, mezclado y monitoreo para instrumentos musicales electr nicos.
Caracter sticas
Uno de los m s exitosos e influyentes sistemas de parlantes profesionales.
Dispositivo Differential Drive R low-frequency de 15", con doble im n de neodimio para reducir la distorsi n y
disminuir el peso.
Mezclador incorporado de 3 entradas. Una entrada balanceada micr fono/linea, dos entradas de nivel de l nea
para micr fono de 1/4". Ecualizaci n de dos bandas.
Circuito balanceado - salida directa / mezclada para Bafles SK-6P adicionales "encadenados" o enviar la salida
mezclada a una consola de mezclado.
Thermomaster R Total Termal Management System R .Una sola pieza, bafle de aluminio fundido integra el armaz n
del amplificador de bajos, la bocina y el disipador de calor. El movimiento del aire en el puerto de aletas disipa el
puerto de aletas desipa el calor no se necesitan ventiladores de enfriamiento, ni externos ni internos .
Cerramiento de copol mero negro, resistente, liviano, con bafle de aluminio fundido.
Recept culo con polos de instalaci n de 35mm integrado con tornillo mariposa para asegurarlo.
Recept culo de ngulos m ltiples para aplicaci n en la parte delantera o monitor de escenario.
El procesador din mico protege a los amplificadores y parlantes de sobrecargas, sin producir cambios extremos
en la respuesta de frecuencia al variar los niveles.
Mayor rendimiento de baja frecuencia. Brinda bajos inferiores a 40Hz de gran potencia.
COMIENZO RAPIDO
SK-6P
COMIENZO RAPIDO
1. Haga girar completamente los controles de INPUT (ENTRADA) 1, 2, y 3 en sentido contrario a las agujas del reloj.
2. Configure el interruptor MIC/LINE.
Si se va a conectar un micr fono directamente al INPUT 1, configure la posici n MIC/LINE en MIC.
Si se va a conectar directamente al INPUT 1 un mezclador, un reproductor de CD o de casetes, o un instrumento
musical electr nico, configure el interruptor MIC/LINE en la posici n LINE.
3. Configure los controles EQ HF y LF en su posici n central de detenci n.
4. Enchufe el cable de corriente el ctrica CA una l nea de 3 cables, con una descarga a tierra apropiada.
5. Enchufe el cable XLR del mezclador o del micr fono en el conector INPUT 1.
6. Conecte las fuentes no balanceadas (si las usa) a los conectores de entrada LINE 2 y LINE 3.
7. PROCEDIMIENTO DE ENCENDIDO
En primer luger, conecte el mezclador a la corriente el ctrica, a las fuentes de audio o a los instrumentos musicales
que alimentan su SK-6P.
Luego, encienda el interruptor de corriente el ctrica (el indicador de encendido del panel delantero se iluminar ).
Cuando apague el sistema ejecute este proceso al rev s.
8.CONFIGURAR EL VOLUMEN
Si est usando una consola de mezcla de audio, consulte las instrucciones del fabricante para configurar
correctamente la estructura de ganancia.
Eleve el volumen de sus fuentes al nivel que se usar en interpretaciones y al hablar, cantar o reproducir en el equipo.
Haga subir el control del INPUT 1(en sentido de las agujas del reloj) hasta que se alcance el nivel deseado de
volumen. Si est utilizando un micr fono, haga subir suavemente el control del INPUT 1 para evitar reacci n.
Si est usando las entradas INPUT 2 e INPUT 3, haga subir el control del INPUT 2 hasta que se alcance el nivel de
volumen deseado.
9.CONTROLE EL INDICADOR DE MAXIMO
El indicador de MAXIMO destella cuando el amplificador de los parlantes se aproxima a la salida m xima. Es normal
observar destellos ocasionales cuando est realizando operaciones con sonidos muy altos. Sin embargo, si el
INDICADOR DE MAXIMO se mantiene iluminado, el sonido puede distorsionarse y es una indicaci n de que se
necesitan m s parlantes o un volumen de reproducci n m s bajo para su aplicaci n espec fica.
CONTROLES Y CONEXIONES
SK-6P
CONTROLES Y CONEXIONES
La secci n de audio del SK-6P incluye caracter sticas impactantes que
mejoran la flexibilidad de los parlantes.
LOOP
MIX
Conectores
INPUT 1 entrada
Esta entrada balanceada acepta un conector est ndar XLR (hembra ).
~
Aqu es posible conectar un amplio rango de senales
(-44 dBu a +20
dBu nominal) desde micr fonos,consolas de mezcla de audio e
instrumentos musicales electr nicos. Cuando utiliza una nica entrada
de audio a los parlantes, ese es la entrada a utilizar. La sensibilidad de
esta entrada es controlada por el MIC/LINE SWITCH interruptor de
mezcla/l nea y el control rotativo INPUT 1.
OUTPUT
INPUT1
HIGH
LINE
MIC
INPUT 1
VOL
PEAK
MIN
MAX
INPUT 2
VOL
MIN
OUT(salida)
Este conector de salida XLR (macho) trabaja con el MIX/LOOP SWITCH
para proveer env o de audio desde su SK-6P.
MAX
INPUT 3
VOL
INPUT2
MIN
MAX
INPUT3
HF
-15dB
+15dB
EQ
LF
SIGNAL
-15dB
+15dB
Interruptores
MIC/LINE
El interruptor MIC/LINE afecta s lo al INPUT 1. Selecciona entre dos
rangos sensibilidad. Este interruptor se usa para igualar la sensibilidad
de entrada del SK-6P con el nivel de salida del dispositivo conectado
al INPUT 1. Bajando el interruptor MIC/LINE selecciona MIC(m s
sensible .)
PRECAUCION: antes de ajustar este interruptor, aseg rese de hacer
girar totalmente el control del INPUT 1 en sentido contrario a las agujas
del reloj. Luego de que se haya ajustado el interruptor MIC/LINE, gire
suavemente el control INPUT 1 en el sentido de las agujas del reloj
hasta que se obtenga el volumen deseado.
Use la plsici n MIC (deprimida) cuando un micr fono est conectado al INPUT 1.
Use la posici n LINE (desconectado) cuando una fuente de nivel de l nea, como una consola de mezcla de audio,
dispositivos de reproducci n de audio o instrumentos musicales electr nicos est n conectados a INPUT 1.
CONTROLES Y CONEXIONES
SK-6P
MIX/LOOP (Mezcla/bucle)
~
Este interruptor selecciona la fuente de la senal,
para el conector OUT (de salida).
PRECAUCION: antes de ajustar este interruptor, aseg rese de configurar el control de nivel de entrada de cualquier
equipo conectado a esta salida a su m nima configuraci n de ganancia (menos sensible).
~
En la posici n desactivada, s lo la senal
del conector INPUT 1 se dirige directamente al conector OUT. Si se cambian
~
las otras configuraciones en el panel de audio, la senal
de audio no resultar afectada. Las entradas INPUT 2 e INPUT 3
no estar n presentes en el conector de salida. Use esta configuraci n cuando quiera alimentar varios bafles potenciados
~
con la misma senal.
En la posici n MIX, se enviar una combinaci n pos-ecualizador de todas las entradas al parlante (INPUT 1, 2 y 3), al
~
conector OUT. Cualquier cambio a la configuraci n del nivel de entrada o del EQ (ecualizador) afectar la senal
de OUT
(salida). Vea la secci n de EJEMPLOS DE SISTEMA para obtener m s detalles de c mo puede utilizarse esta modalidad.
CONTROLES
INPUT 1
Ajuste el nivel del INPUT 1. Use este contor para igualar la sensibilidad de entrada del SK-6P con el nivel de salida del
mezclador, micr fon, o instrumento conectado al INPUT 1. Es err neo pensar que este control cambia la potencia de un
sistema. Su SK-6P producir la potencia de salida indicada sin importar como est contigurado este control. El control del
~
INPUT 1 determina cu nta senal
se necesita en la salida para que el sistena logre su m xima salida.
INPUT 2 e INPUT 3
Estos controles ajustan el nivel de las salidas conectadas al INPUT 2 y 3.
LF EQ
Este control permite hasta 15dB de corte o amplificaciones de 75 Hz. Si el sistema parece muy "estridente" o con bajos
pesados, gire este control en sentido contrario al de las agujas del reloj. Si el sistema suena muy "tenue" o le falta la
potencia m s baja de la gama, gire este control en el sentido de las agujas del reloj. Para configurar la baja frecuencia EQ
a "plano" (sin corte o amplificaci n del EQ),configure este control a la posici n central.
HF EQ
Este control permite hasta 15dB de corte o amplifica a 75Hz. Si el sistema parece muy "estridente" o "met lico", gire este
control en sentido contrario al de las agujas del reloj. Si el sistema suena muy "sombr o" o carece de "brillo",gire este
control en el sentido de las agujas del reloj. Para configurar la baja frecuencia EQ a "plano" (sin corte o amplificaci n del
EQ), configure este control a la posici n central.
SK-6P
INDICADORES
MAXIMO
El INDICADOR LUMINOSO DE MAXIMO (diodo emisor de luz) se enciende para indicar que el sistema se acerca al l mite.
El umbral para que se encienda esta luz es de alrededor de 2dB debajo del l mite. Un parpadeo ocasional de esta luz en
los picos de sonoridad es aceptable. Si este indicador luminoso est encendido durante un per odo mayor que breves picos
din micos, indica que el sistema est sobrecargado. Si esto ocurre con frecuencia, provocar dlstorsiones desagradables
que forzar n al equipo, pudiendo generar fallas prematuras en el sistema de parlantes. Si el INDICADOR LUMINOSO DE
MAXIMO se ilumina en forma desmedida:
Reduzca INPUT 1, 2, y 3.
Reduzca el nivel de salida del mezclador, del instrumento musical, u otra fuente conectada al parlante.
Si hay un exceso de amplificaci n en el LF EQ o HF EQ (ecualizador de baja o alta frecuencia), vuelva los controles
a la posicion de "llano" (centrada) .
~
SENAL
~ disponible desde INPUT 1.
Se ilumina para indicar una senal
MIC(micr fono)
~ indicadora senala
~
Esta senal
que el interruptor MIC/LINE est en la posici n MIC (deprimido).
Aseg rese de que el parlante est apagado y que el cable de corriente el ctrica est desconectado del parlante.
El selector de voltaje se encuentra directamente debajo del conector IEC macho en el parlante.Rompa el sello de
f brica y deslice el interruptor a la configuraci n apropiada.
Configure el selector de voltaje a 115V or 230V el que corresponda a su pa s.
Luego de verificar que est seleccionado el voltaje correcto, vuelva a conectar el cable de corriente el ctrica AC
(conector IEC) y encienda el equipo.
BAJO NINGUNA CIRCUNSTANCIA HAGA FUNCIONAR EL EQUIPO CON EL VOLTAJE EQUIVOCADO SELECCIONADO.
~
SI LO HACE PUEDE PROVOCAR DANOS SERIOS A SU SISTEMA DE PARLANTES, Y QUE DICHOS DANOS NO
ESTARAN CUBIERTOS POR LA GARANTIA..
EJEMPLOS DE APLICACIONES
SK-6P
GUITARRA DE BAJOS
TECLADOS
ENTRADA DE NIVEL
DE LINEA
VOZ
ENTRADA DE NIVEL
DE LINEA
CAJA DIRECTA
GUITARRA PRINCIPAL
~
PROCESADOR DE SENAL
~ ESTEREOL
SENAL
ENTRADA DEL
ECUALIZADOR SALIDA DEL
ECUALIZADOR
ENTRADA DE NIVEL
DE LINEA
ENTRADA DE NIVEL
DE LINEA
EJEMPLOS DE APLICACIONES
Este ejemplo muestra un sistema PA t pico que use un mezclador con un par de SK-6P para la mezcla principal a izquierda
~
y derecha. Una senal
separada del conductor AUX/MONITOR del mezclador se env a a dos SK-6P adicionales ubicados
~
en el basculante trasero, posici n de cuna
para utilizar como monitores de piso.
EJEMPLOS DE APLICACIONES
SK-6P
INPUT 1
INPUT 1
MEZCLADOR DJ
SALIDA DERECHA
SALIDA IZQUIERDA
CRUCE
ELECTRONICO
AMPLIFICADOR
Sintetizador
OUT
INPUT 1
INPUT 2
INPUT 3
S mpler
a la consola de mezcla
REFERENCIA
SK-6P
REFERENCIA
Conexiones - balanceadas y no balanceadas
~
Hay dos tipos b sicos de interconexiones de sistemas de audio para senales
de audio: balanceadas o no balanceadas
igual, pero opuesto con respecto al cable de descarga a tierra.El cable de descarga a tierra s lo act a como un escudo,
~
y no transporta ninguna senal
de audio. La interferencia externa (como la interferencia de frecuencia de radio - RFI)
~
~
est protegida del conductor de la senal
interna, o bien, si ingresa al cableado, senales
opuestas en el extremo de la
conductor "caliente". Los cables de audio no balanceados no rechazan los ruidos de la misma forma que lo hacen las
l neas balanceadas. Las l neas balanceadas son comunes en sistemas tipo hi-fi para el hogar y en las salidas de
~
instrumentos musicales electr nicos. Funcionan bien si la distancia entre los componentes es corta, el nivel de la senal
es relativamente alto y todos los electr nicos utilizados en el sistema son de una AC similar.
Fuentes no balanceadas a SK-6P
Si necesita conectar sus parlantes SK-6P a una fuente no balanceada tiene dos opciones:
Usar los conectores de LINE 2 y LINE 3. Estas entradas son balanceadas pero aceptar n entradas no balanceadas
sin la necesidad de ning n adaptador especial.
Usar un adaptador o cable especial (consultar la secci n "cables y conectores").
REFERENCIA
SK-6P
Cables y conectores
~
Este cable es el ctricamente id ntico al cable de micr fono de 1/4" *TRS (no balanceado) al XLR/M
anterior, y puede usarse de manera intercambiable.
Para conectar productos de audio de consumo, y algunas salidas de mezcladors DJ a entradas de equipos
de audio profesionales
Para conectar salidas de equiposde de audio de consuno a entradas de l neas no balanceadas del SK-6P
y mezcladores .
Para conectar salidas de l nea no balanceada a varios mezcladores a las entradas de grabadores de audio
de consumo.
~
Para separar una salida est reo en senales
independientes a izquierda y derecha.
Para conectar una guitarra el ctrica est reo a dos entradas de audio no balanceadas.
Para conectar una salida de auriculares a dos entradas de audio no balanceadas.
Para cambiar a un TRS mini-phone, para conectar a la salida de un reproductor de CD port til y a placas
de sonido de computadores a un mezclador o parlantes
de potencia.
~
Tambi n se usa para conectar procesadores de senal al "ingreso" de varias consolas de mezcla.
Se usa para "adreviar" una toma a tierra con el fin de eliminar el zumbido causado por "bucles de
conexiones a tierra". Para usar exclusivamente con entradas y salidas balanceadas.
1
2
3
1 (shield)
2
3
Tip
Ring
Sleevee
1 (shield)
2
3
Tip
Ring
Sleevee
1 (shield)
2
3
Tip
1 (shield)
2
3
Center
Shield
Center
Sleeve (shield)
Tip
Sleeve (shield)
Tip
Sleeve (shield)
10
1 (no connection)
2
3
DIAGRAMA DE BLOQUE
SK-6P
Diagrama de bloque
LOOP
MIX
PEAK
OUT
INPUT 1
SIGNAL
INPUT 1
LINE
MIC
EQ
SUM
LOW HIGH
MIC
INPUT 2
INPUT 2
INPUT 3
INPUT 3
11
HPF
90W
LPF
&
DYNAMIC
FILTER
300W
SOLUCION DE PROBLEMAS
SK-6P
SOLUCION DE PROBLEMAS
S ntoma
Sin sonido.
Causa probable
Parlantes no conectados
a l nea de CA activa
El cable de corriente
el ctrica est defectuoso
o mal conectado
Fusible quemado
~
Senal
de sonido distorsionada
y muy fuerte, la luz de
MAXIMO est la mayor a del
tiempo encendida.
Cables y conexiones
defectuosos
La fuente (mezclador,
instrumento, etc.) no
~
emite senal.
Sin sonido. Parlantes
encendidos
Que hacer
Incorrecta estructura de
ganancia
12
SOLUCION DE PROBLEMAS
SK-6P
S ntoma
Se escuchan ruidos o silbidos
en la salida.
Causa probable
Que hacer
Zumbido
Tendido extremadamente largo
del cable no balanceado
El INTERRUPTOR MIX/LOOP
est configurado err neamente
INTERRUPTOR MIXED/LOOP
configurado err neamente
Ganancia excesiva
Retroalimentaci n de los
parlantes y aullidos cuando
se aumenta el volumen del
micr fono.
13
SK-6P
SK-6P
SK-6P
SK-6P
SK-6P