Professional Documents
Culture Documents
by benjaminmailloux
Download
11 Step s
+ Collection
Favorite
There are hardly any instructables on this subject, and none with this design. It's an original
idea by my dad and I. We were going for as cheap as we could go, while still making a
product we wouldn't be embarrassed to use in public.
We built a full set of electronic drum pads, which I'll explain here, and also a low-cost PVC
rack for the drums, which I'll post a separate "how-to" on.
Step 1: Materials
Step 2: Tools
I bought a sheet of 3/4 inch plywood that perfectly fit 9 of my 8 inch circles. Draw them all
out and then cut them all out at once with a jigsaw. The rough edges can just be quickly
hand-sanded smooth.
We got 16 foam, 8 inch diameter circles out of the 2 foam mats. Because each pad needs 2
circles (once for under the peizo+sheet-metal layer, and one for above) this is enough for 8
drum pads. As with the wood, we just drew them all out with sharpie, then cut them out with
scissors.
*For the first pad, we used 2 mouse-pads instead of the foam, but quickly realized that this
would be far too expensive at 4 dollars per mouse-pad.]
For the sheet metal circles, we just rolled out the aluminum flashing, traced our circles, and
used the metal snips to cut them out. If you cut them out as squares first, then trim them to
circles, it makes the process a lot safer and easier. (The edges are sharp. Be Careful.)
There will be lots of left-over metal from the circles. What i did was salvage this by cutting
out squares about 2x2 inches. these will be the mounts for the jacks, so they will also need a
1/4 inch hole drilled through the middle.
The vinyl can be cut into circles with a diameter of 8 inches or just under, depending on how
you want your edges to look. mine are right at 8 inches, the same as almost all other parts of
this design.
These circles can just be traced out, then cut with scissors.
The fabric circles will be the one element of this project that will be cut larger than 8 inches.
These need to be able to wrap around the layers of wood, foam and metal, and be stapled
on the underside of the plywood. A diameter of around 14 inches should give you enough to
work with. This can also be traced out and carefully cut with scissors.
As previously mentioned, a 1/2 inch hole must be drilled in the plywood circles. This hole
should be about half way between the center and the outside of the circle. Space must just
be left in the center for the mounting bracket.
For each pad, one of the two foam circles must also have a small hole poked through it. this
should line up with the hole drilled in the plywood circle. The other foam circle is left as it is.
As mentioned already, a 1/4 inch hole must also be drilled in the center of the small sheet
metal squares. Use caution with this, as the small pieces of metal have a tendency to spin
as the drill bit goes through. I manged to cut myself on one of these spinning hazards =P
The Peizo element is really the key to this whole project. I'm certainly not an expert on the
subject, but, to the best of my knowledge, the peizo produces a small charge of electricity
using crystals inside. The metal side of the peizo is what takes in the impact and vibration.
What we are doing in this project, is basically increasing the footprint of this sensor, so that it
covers the entire surface of the pad. This is the "reflection plate" method.
For speed, flexibility and cost, I used regular hot glue to attach the peizo element, metal side
down, to the center of the circles of sheet metal. putting the glue under and then sticking the
peizo into it didn't work well, so i just set it flat on the metal, and put glue all around the
edges. While I had the glue ready, I also added a little over the small solder points on the
peizo for support.
With the wires through the bottom of the plywood layer, the jack can now be attached.
1. unscrew the nut from the RCA jack, and remove the collar connector and lock-washer.
2. solder the red wire solidly to the collar connection.
3. push the small, threaded end of the jack through the 1/4 inch hole in the 2x2 inch sheetmetal square.
4. slide the lock washer back over the threaded jack, against the sheet metal.
5. Slide the collar connection with the red wire soldered to it, over the threaded back of the
jack, against the lock washer.
6. screw back on the nut, holding the visible front of the jack and firmly turning the nut on the
back with pliers.
7. with the whole assembly tightened down, the black wire can now be soldered to the pin
connector of the jack.
You now have a whole, mounted jack assembly that can easily be pushed into the existing
hole in the plywood. The sheet metal mount now lies flat against the plywood, and can
simply be stapled on.
With the fabric wrapped, stapled, and trimmed, the vinyl can now be glued on.
1. Lay the vinyl circle over the bottom of the pad and the jack, lining it up with the edges.
2. feel where the jack lines up with the vinyl and mark this point.
3. I then just used a regular hole punch to make a perfect hole to line up with the jack.
4. test the fit of this hole to be sure everything lines up well and hides the rough fabric edges
and staples.
5. Spread an even amount of hot glue all around the pad, going almost to the edges, and
especially right around the jack.
6. lay the vinyl down flat in the glue, and smooth out the surface.
You now have a drum pad with a nicely finished base, and a jack protruding from it.
Depending on how you plan to mount your pads, this step may differ.
I'll give the following directions for those doing this the same way I did. This is also the way
that will allow the pads to match up with the rack design I will be posting soon.
1. The brackets I used for the pads to mount were found in the plumbing department at
Home Depot. They are commonly used for mounting pipe-hangers off of walls and ceilings.
2. the bracket has to countersunk holes of about 1/4 inch, and in the center A 3/8 inch
receiving hole threaded like a nut.
3. Find as close to the center of the pad as you can and mark with a dot.
4. Line this dot up with the center threaded hole of the bracket (so that the pad will have
proper balance)
5. Use 2 small screws no longer than 1 inch to screw the bracket to the plywood beneath the
vinyl.
At this point, You should have a nice looking, responsive electronic drum pad, for far less
than it would cost to buy a factory-made one, even used =P
I hope this Instructable gave someone some ideas of their own.
Thanks for reading!
Feel free to leave comments here, and any questions can be sent to
Benjaminmailloux@yahoo.com
I'd be glad to answer.
I