Professional Documents
Culture Documents
<<
Operation process
Self check
Power ON
<<
<</Rst
<<
SET
all LED on
PV display
Output value display
COM
AL1
AL2
COM
AL1
AL2
23
24
22
10
12
21
9
11
20
8
19
18
17
16
1 4
15
+
6
4
+
12V
SG
11
OUT
LA8-VNNNA
SET
Response for 20mA/10V output high value
setting,range:0trHUSP
SET
communication address : 000-200, Baud rate:
regular: 9.6KBIT(hidden when there is no output)
SET
LCK=010,is for read only.
LCK=000 means the parameter can be momodified.
Password selection,range:0-200
T
K g
g
0-10V
setting,range:0trLUSP
be in the Low LED. Press external terminal RST to reset, SUM to add up
1 3
12
Response for 4mA/0V output low value
CND
SET
80-265V AC
SG(mV)
Reserves
10
SET
0:0000 1:000.0
2:00.00 3:0.000,
mV
SET
<<
80-260V AC/DC
set USP=Standard weight ( that equal to 20% load cell scale or more),
weight.
<</Rst
AL2 AL1
AL3
12V
SET
SET
SET
AL1
AL2
OUT
Load cell
Then add the weight equal to setted USP(3kg), press UP key>5s until
Panel
420mA/0-10V
Range: 50.0
Tare value, Net weight(PV)=the actual weight-tare
SET
80-265V AC
Application examples
Alarm3 mode setting(Hiden when no AL3)
H: High output
L: Low output
10 9
SET
N:none
AL2: R:relay S:SSR/LOGIC
N:none
Analogue : Blank: none
I : DC 4-20mA
V: 0-10V
Parameters setting
+12V
GND SGmV
RST
A.Press and hold SET key > 3 sec, enter / quit parameters setting menu.
Communication
RXD TXD
SET
AuxiliaryPower Supply
SET
N:none
AL1
AL2
AL3
Input
Analog output
90-260V AC
Alarm 2 setting,range
LSPAL2USP,factory setting: 70.0
Relay
Communication interfaceBlank:none
2:R232 4:R485
SET
+12V
12 11 10 9
Accuracy
Sampling speed
GND
Code Illustration
L -
SET
Power Consumption
The instrument provides isolated load cell power (regularly one 12V/40mA),
connect with load cell directly,up to 6 outputs controll for groups of batching
or single ; Data/Peak value holding function for choice. RS485 communication
interfaceprovides remote link with computer/PLC. Besides, you can Start/Pause/
Accumulate/Clear tare weight/average/clear zero,etc. with external control
terminal.
up or down key
Specifications
Power
Application
420mA
Sum Rst mV
Alarm 1 setting,range
0AL1USP
MYPIN product!
Before operating this instrument, please carefully read this manual and
fully understand its contents. If any problems, please contact our sales or
distributors whom you buy from. This manual is subject to change without
prior notice.
On displaying estate, press UP and DOWN key for more than 3 seconds to access to parameter SEL setting.The operation steps
are the same as the other settings. After setting, press UP and DOWN key to quit.This operation is to modify SEL value ONLY. Other
parameters are fixed by manufacturer. Please do not make any change.
SET
SET
SET
SET
.
Set PVF=0.000,
B. Record the displaying value(PV1) when no weight on the load cells(eg.100.5kg).
C. Add the standard weight (the weight should be larger than 20% of the total load cell weight,eg.500kg).
Recorder the displaying value(PV2)(eg. 630kg).
D. Calculation: The actual weight added(eg. 500kg)/(PV2-PV1) eg.500/(630-100.5)=0.9442.
A. Set USP=the total weight of all input load cells(eg. each load cell is 1000KG, 3 load cells in total, the
total weight is 3000kg.Then set USP=3000.).
of no use
.
of no use
.
of no use
.
If SEL=XXX1XX,
that means the user cant do on-site weight adjustment by pressing UP/DOWN key.
If SEL=XXX0XX,
that means the user can do on-site weight adjustment by pressing UP/DOWN key.
Note:
*** X means the original data. Do not make modification.
***Just make modification to data 1/0
***Factory setting is XXX0XX.
After on-site adjustment,make sure SEL=XXX1XX.This is to avoid incorrect display by users inappropriate key-pressing operation.