Professional Documents
Culture Documents
(Part6 )-1288
( Reaffirmed 1998 )
Indian Standard
SPECIFICATION FOR
FABRICATED PVC FITTINGS FOR
POTABLE WATER SUPPLIES
PART 5 SPECIFIC REQUIREMENTS FOR EQUAL TEES
( First Revision )
FirstReprint0CTOBERm1993
UDC 621.643.4.062.2[678.743.221:696.117
@I Copyright
BUREAU
OF
MANAK BHAVAN,
GT2
INDfAN
1989
STANDARDS
9 BAHADUR SHAH
NEW DELHI 110002
ZAFAR
MARG
February 1989
Indian Standard
SPECIFICATION FOR
FABRICATED PVC FITTINGS FOR
POTABLE WATER SUPPLIES
P-ART 5
SPECIFIC REQUIREMENTS
FOR EQUAL
TEES
( First Revision)
0.
FOR
EWORD
PVC fittings
parts of the
Part 5
Part 8
for 60 bends
for 45 bends
for 90 bends
1. SCOPE
1.1 This standard
( Part 5 ) lays down the
requirements of manufacture,
dimensions and
marking for fabricated PVC equal tees for
potable water supplies.
and
to
2.2 Manufacture
2.2.1 A typical
shown in Fig. 1.
2. REQUIREMENTS
2.1 General
sampling
conform
illustration
of equal tee
is
for
I
Es: 10124(Part5)-1988
*PVCwelded by solvent or welding rod and with fibre glass reinforcement of 40 mm width and 3 mm minimum
thiilcness.
B I mean socket internal diameter at mid-point of socket length asspecified in IS : 10124 ( Part I )-1988*.
L - minimum socket length in accordance with IS : 10124 ( Part i )-1988*.
B = 1.45 X nominal out&do diameter of the pipe + 6 mm.
t - minimum wall thickness of equal tees calculated on the basis of 90 percent of the minimum wall thickness
of the corresponding size and pressure class of pipe rounded off to the next higher 0.1 mm.
Noru-The
drawing is only intended to define fho terms used
design features.
FIG.
1 EQUAL TEE
SIZE
Min
3. MARKING
3.1 Each equal tee fitting shall be marked
the following information:
a) W;;~facturers
name
(1)
63
75
with
90
110
125
140
160
180
200
225
250
280
315
355
400
450
500
560
630
or indentification
).
(2)
98
c 3)
14
(4)
2.0
(5)
32
115
137
166
188
209
238
267
296
333
369
412
463
521
586
659
731
818
920
17
19
2.3
2.7
29
3.4
38
4.2
47
52
58
63
7.3
8.2
9.3
10.3
116
13.0
24
28
3.4
3.9
4.4
4.9
55
6.2
6.9
7.7
8.6
97
108
122
13.7
153
17.2
192
3.8
45
55
6.3
70
8.0
9.0
10.0
112
125
13.9
15.6
17.7
19.8
22.4
248
27.8
31.3
Colour
Green
Yellow
Class 4 ( 10 MPa )
3.1.1 Each equal tee fitting
marked with the Standard Mark.
Blue
may
also be
BIS is a statutory institution established under the Bureau of Indian Standards Act, 2986 to
promote harmonious development of the activities of standardization, marking and quality
certification of goods and attending to connected matters in the country.
CopJrigbt
BIS has the copyright of all its publications. No part of these publications may be reproduced in
any form without the prior permission in writing of EIS. -This does not preclude the free use, in
the course of implementing the standard, of necessary details, such as symbols and sixes, type or
grade designations. Enquiries relating to copyright be addressed to the Director ( Publications ), BIS.
Rtrition of Indian Stwdards
Indian Standards are reviewed periodically and revised, when necessary and amendments, if any,
are issued from time to time. Users of Indian Standards should ascertain that they are in possession
of the latest amendments or edition.
Amend No.
Text Affected
Date of Jssue
Telegrams : Manaksanstha
( Common to all Offices )
Regional Offices :
Telephone
I 331 01
13 31
75
160036
37 86 62
21843
41~29 16
6 32 92 95