Professional Documents
Culture Documents
SECTION
BCS
CONTENTS
BCM
PRECAUTION ............................................... 3
PRECAUTIONS ................................................... 3
BUZZER .....................................................................16
BUZZER : CONSULT Function (BCM - BUZZER)....16
SYSTEM .............................................................. 7
BODY CONTROL SYSTEM ........................................ 7
BODY CONTROL SYSTEM : System Description...... 7
COMBINATION SWITCH READING SYSTEM ........... 8
COMBINATION SWITCH READING SYSTEM :
System Diagram ........................................................ 8
COMBINATION SWITCH READING SYSTEM :
System Description ................................................... 8
SIGNAL BUFFER SYSTEM ...................................... 11
SIGNAL BUFFER SYSTEM : System Diagram ...... 11
SIGNAL BUFFER SYSTEM : System Description.... 12
POWER CONSUMPTION CONTROL SYSTEM ....... 12
POWER CONSUMPTION CONTROL SYSTEM :
System Diagram ...................................................... 12
BCS
HEADLAMP ...............................................................19
HEADLAMP : CONSULT Function (BCM - HEADLAMP) ......................................................................19
WIPER ........................................................................20
WIPER : CONSULT Function (BCM - WIPER) .......20
FLASHER ...................................................................21
FLASHER : CONSULT Function (BCM - FLASHER) ..........................................................................21
BCS-1
Description .............................................................. 68
DTC Logic ............................................................... 68
Diagnosis Procedure ............................................... 68
TRUNK ...................................................................... 27
TRUNK : CONSULT Function (BCM - TRUNK) ..... 27
BCS-2
PRECAUTIONS
[BCM]
PRECAUTION
PRECAUTIONS
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
INFOID:0000000009951595
The Supplemental Restraint System such as AIR BAG and SEAT BELT PRE-TENSIONER, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. Information necessary to service the system safely is included in the SR and SB section of
this Service Manual.
WARNING:
To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death in
the event of a collision which would result in air bag inflation, all maintenance must be performed by
an authorized NISSAN/INFINITI dealer.
Improper maintenance, including incorrect removal and installation of the SRS, can lead to personal
injury caused by unintentional activation of the system. For removal of Spiral Cable and Air Bag
Module, see the SR section.
Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or harness connectors.
BCS
BCS-3
COMPONENT PARTS
[BCM]
SYSTEM DESCRIPTION
COMPONENT PARTS
BODY CONTROL SYSTEM
BODY CONTROL SYSTEM : Component Parts Location
INFOID:0000000009461986
ALMIA0585ZZ
1.
BCS-4
COMPONENT PARTS
[BCM]
ALMIA0586ZZ
1.
2.
4.
5.
3.
BCS
BCS-5
COMPONENT PARTS
[BCM]
AWMIA1311ZZ
1.
2.
Combination meter
BCS-6
3.
IPDM E/R
SYSTEM
[BCM]
SYSTEM
INFOID:0000000009461989
OUTLINE
BCM (body control module) controls various electrical components. It receives the information required from
CAN communication and the signals received from each switch and sensor.
BCM has a combination switch reading function for reading the status of combination switches (light, turn
signal, wiper and washer) in addition to functions for controlling the operation of various electrical components. It also has a signal transmission function for other systems, and a power consumption control function
that reduces the power consumption with the ignition switch OFF.
BCM is equipped with a diagnosis function that operates with CONSULT and allows for various settings to
be changed.
Refer to
Headlamp system
Panic alarm
Rear window defogger system
BCS
O
DEF-7, "System Description"
BCS-7
SYSTEM
[BCM]
Refer to
Warning function
INFOID:0000000009461990
AWMIA1215GB
INFOID:0000000009461991
OUTLINE
BCM reads the status of the combination switch (light, turn signal, wiper and washer) and recognizes the
status of each switch.
BCM has a combination of 5 output terminals (OUTPUT 1 - 5) and 5 input terminals (INPUT 1 - 5) and reads
a maximum of 20 switch states.
BCS-8
SYSTEM
[BCM]
AWMIA1216GB
System
INPUT 1
INPUT 2
INPUT 3
INPUT 4
INPUT 5
OUTPUT 1
FR WASHER
FR WIPER LOW
TURN LH
TURN RH
OUTPUT 2
FR WIPER HI
FR WIPER INT
PASSING
HEADLAMP 1
OUTPUT 3
INT VOLUME 1
HEADLAMP 2
HI BEAM
OUTPUT 4
INT VOLUME 3
AUTO LIGHT
TAIL LAMP
OUTPUT 5
INT VOLUME 2
FR FOG
BCS
JPMIA0609GB
NOTE:
BCM reads the status of the combination switch at 60 ms intervals when BCM is controlled at low power
consumption control mode.
BCM operates as follows and judges the status of the combination switch.
- It operates the transistor on OUTPUT side in the following order: OUTPUT 1 2 3 4 5, and outputs
voltage waveform.
- The voltage waveform of OUTPUT corresponding to the formed circuit is input into the interface on INPUT
side if any (1 or more) switches are ON.
BCS-9
SYSTEM
[BCM]
JMMIA0326GB
Operation Example
In the following operation example, the combination of the status signals of the combination switch is replaced
as follows: INPUT 1 - 5 to 1 - 5 and OUTPUT 1 - 5 to A - E.
Example 1: When a switch (TAIL LAMP) is turned ON
The circuit between OUTPUT 4 and INPUT 5 is formed when the TAIL LAMP switch is turned ON.
AWMIA1217GB
BCM detects the combination switch status signal 5D when the signal of OUTPUT 4 is input to INPUT 5.
BCM judges that the TAIL LAMP switch is ON when the signal 5D is detected.
Example 2: When some switches (TURN RH, TAIL LAMP) are turned ON
BCS-10
SYSTEM
[BCM]
< SYSTEM DESCRIPTION >
The circuits between OUTPUT 1 and INPUT 5 and between OUTPUT 4 and INPUT 5 are formed when the
TURN RH switch and TAIL LAMP switch are turned ON.
F
AWMIA1218GB
BCM detects the combination switch status signal 5AD when the signals of OUTPUT 1 and OUTPUT 4 are
input to INPUT 5.
BCM judges that the TURN RH switch and TAIL LAMP switch are ON when the signal 5AD is detected.
BCM judges the wiper intermittent dial 1 - 7 by the status of INT VOLUME 1, 2, and 3 switches.
Switch status
Wiper intermittent
dial position
INT VOLUME 1
INT VOLUME 2
INT VOLUME 3
ON
ON
ON
ON
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
ON
ON
OFF
ON
OFF
INFOID:0000000009461992
BCS
AWMIA1275GB
BCS-11
SYSTEM
[BCM]
INFOID:0000000009461993
OUTLINE
BCM has the signal transmission function that outputs/transmits each input/received signal to each unit.
Input
Output
Description
INFOID:0000000009461994
ALCIA0030GB
INFOID:0000000009461995
OUTLINE
BCM incorporates a power saving control function that reduces the power consumption according to the
vehicle status.
BCM switches the status (control mode) by itself with the power saving control function. It performs the sleep
request to each unit (IPDM E/R and combination meter) that operates with the ignition switch OFF.
Normal mode (wake-up)
BCS-12
SYSTEM
[BCM]
< SYSTEM DESCRIPTION >
BCM receives the sleep-ready signal (ready) from IPDM E/R and combination meter via CAN communication.
BCM transmits the sleep wake up signal (sleep) to each unit when all of the CAN sleep conditions are fulfilled.
Each unit stops the transmission of CAN communication with the sleep wakeup signal. BCM is in CAN communication sleep mode.
BCM is in the low power consumption mode and performs the low power consumption control when all of the
BCM sleep conditions are fulfilled with CAN sleep condition.
Sleep condition
Wake-up operation
BCM changes from the low power consumption mode to the CAN communication sleep mode when the any
of the BCM wake-up conditions are fulfilled. Only the control with BCM is activated.
BCM transmits the sleep wake up signal (wake up) to each unit when any of the CAN wake-up conditions
are fulfilled. It changes from the low power consumption mode or the CAN communication sleep mode to the
normal mode.
Each unit starts the transmission of CAN communication with the sleep wake up signal. In addition, the combination meter transmits the wake up signal to BCM via CAN communication to report the CAN communication start.
BCM wake-up condition
BCS
BCS-13
INFOID:0000000009461996
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
APPLICATION ITEM
CONSULT performs the following functions via CAN communication with BCM.
Direct Diagnostic Mode
Description
Ecu Identification
Data Monitor
Active Test
Work support
Configuration
SYSTEM APPLICATION
BCM can perform the following functions.
Work support
REAR DEFOGGER
Warning chime
BUZZER
INT LAMP
Exterior lamp
HEADLAMP
WIPER
FLASHER
Air conditioner
AIR CONDITIONER
INTELLIGENT KEY
Combination switch
COMB SW
BCM
BCM
Immobilizer
IMMU
Door lock
DOOR LOCK
BATTERY SAVER
Trunk open
TRUNK
THEFT ALM
Active Test
Sub System
Configuration
Data Monitor
System
Ecu Identification
BCS-14
RAP system
RETAINED PWR
SIGNAL BUFFER
TPMS
Configuration
Work support
Active Test
Data Monitor
Sub System
Ecu Identification
System
DOOR LOCK
INFOID:0000000009461997
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
Indicates condition of lock signal from door lock and unlock switch.
Indicates condition of unlock signal from door lock and unlock switch.
ACTIVE TEST
Test Item
DOOR LOCK
Description
This test is able to check door lock operation [ALL LOCK/ALL UNLK].
WORK SUPPORT
Support Item
DOOR LOCK-UNLOCK SET
BCS
Setting
Description
On*
Off
MODE2
MODE1*
BCS-15
Setting
Description
MODE3
MODE2
MODE1*
Doors lock automatically when vehicle speed reaches 24 km/h (15 mph).
Off
MODE3
MODE2
MODE1*
Off
* : Initial setting
REAR DEFOGGER
REAR DEFOGGER : CONSULT Function (BCM - REAR DEFOGGER)
INFOID:0000000009461998
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
PUSH SW [On/Off]
ACTIVE TEST
Test Item
REAR DEFOGGER
Description
This test is able to check rear window defogger operation [Off/On].
WORK SUPPORT
Support Item
Setting
Description
MODE3
MODE2
MODE1*
* : Initial setting
BUZZER
BUZZER : CONSULT Function (BCM - BUZZER)
INFOID:0000000009461999
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
Indicates vehicle speed signal received from ABS on CAN communication line.
BCS-16
Description
FR FOG SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
ACTIVE TEST
Test Item
Description
This test is able to check seat belt warning chime operation [On/Off].
REVERSE WARNING
ID REGIST WARNING
This test is able to check TPMS transmitter ID regist warning chime operation [On/Off].
INT LAMP
INT LAMP : CONSULT Function (BCM - INT LAMP)
INFOID:0000000009462000
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
REQ SW -DR [On/Off]
Description
Indicates condition of lock signal from door lock and unlock switch.
Indicates condition of unlock signal from door lock and unlock switch.
RKE-LOCK [On/Off]
RKE-UNLOCK [On/Off]
BCS
ACTIVE TEST
Test Item
Description
INT LAMP
WORK SUPPORT
NOTE:
Revision: November 2013
BCS-17
Setting
On
Description
Off*
NOTE:
Do not use this function since interior room lamp control is changed.
On
Off*
On*
Off
* : Initial setting
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
RKE-LOCK [On/Off]
Description
Indicates condition of lock signal from keyfob.
RKE-UNLOCK [On/Off]
RKE-TR/BD [On/Off]
RKE-PANIC [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
Indicates condition of unlock signal from door lock and unlock switch.
ACTIVE TEST
Test Item
Description
INT LAMP
DOOR LOCK
This test is able to check door lock operation [OTR ULK/AS UNLK/DR UNLK/ALL ULK/ALL
LCK].
This test is able to check keyfob power window down operation [Off/On].
FLASHER
HORN
TRUNK/GLASS HATCH
WORK SUPPORT
Revision: November 2013
BCS-18
PW DOWN SET
Setting
Description
On*
Off
Off
On*
MODE4*
MODE3
Lock Only
MODE2
Unlock Only
MODE1
OFF
MODE3
1 min
MODE2
OFF
MODE1*
5 min
MODE3
1.5 sec
MODE2
OFF
MODE1*
0.5 sec
MODE3
5 sec
MODE2
OFF
MODE1*
3 sec
C
Hazard warning lamp function can be changed in this mode.
D
Auto locking function can be changed in this mode.
*: Initial setting
HEADLAMP
HEADLAMP : CONSULT Function (BCM - HEADLAMP)
INFOID:0000000009462002
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Description
PUSH SW [On/Off]
Indicates vehicle speed signal received from ABS on CAN communication line.
BCS
BCS-19
Description
Indicates outside brightness voltage signal from optical sensor filtered by BCM.
ACTIVE TEST
Test Item
Description
FR FOG LAMP
This test is able to check head lamp illumination dimming operation [On/Off].
WORK SUPPORT
Support Item
TWILIGHT ON
WIPER LINK
Setting
Description
MODE2*
MODE1
MODE4
MODE3*
MODE2
MODE1
MODE4
MODE3
MODE2
MODE1*
Normal setting.
MODE 8
MODE 7
MODE 6
ILL DELAY SET
MODE 4
MODE 5
MODE 3
MODE 2
MODE 1*
* : Initial setting
WIPER
WIPER : CONSULT Function (BCM - WIPER)
INFOID:0000000009462003
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
PUSH SW [On/Off]
Indicates vehicle speed signal received from ABS on CAN communication line.
BCS-20
Description
FR WIPER HI [On/Off]
FR WIPER LOW [On/Off]
FR WASHER SW [On/Off]
Indicates front wiper auto stop signal received from IPDM E/R on CAN communication
line.
INT VOLUME [1 7]
ACTIVE TEST
Test Item
FR WIPER
Description
This test is able to check front wiper operation [Hi/Lo/INT/Off].
WORK SUPPORT
Support Item
WIPER SPEED SETTING
Setting
Description
On
Front wiper intermittent time linked with vehicle speed and wiper dial position.
Off*
* : Initial setting
FLASHER
FLASHER : CONSULT Function (BCM - FLASHER)
INFOID:0000000009462004
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
REQ SW -DR [On/Off]
PUSH SW [On/Off]
Description
BCS
HAZARD SW [On/Off]
RKE-LOCK [On/Off]
RKE-UNLOCK [On/Off]
RKE-PANIC [On/Off]
ACTIVE TEST
Test Item
FLASHER
Description
AIR CONDITIONER
AIR CONDITIONER : CONSULT Function (BCM - AIR CONDITIONER)
INFOID:0000000009462005
CAUTION:
Revision: November 2013
BCS-21
DATA MONITOR
Monitor Item [Unit]
Description
INTELLIGENT KEY
INTELLIGENT KEY : CONSULT Function (BCM - INTELLIGENT KEY)
INFOID:0000000009462006
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Main
Description
PUSH SW [On/Off]
BRAKE SW 1 [On/Off]
BRAKE SW 2 [On/Off]
DETE/CANCL SW [On/Off]
Indicates condition of detent switch received from TCM on CAN communication line.
Indicates condition of N (neutral) position from IPDM E/R on CAN communication line.
BCS-22
Main
Description
ID OK FLAG [Set/Reset]
When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
When remote keyless entry receiver receives the signal transmitted while
operating on Intelligent Key, the numerical value start changing.
RKE-LOCK [On/Off]
RKE-UNLOCK [On/Off]
RKE-TR/BD [On/Off]
RKE-PANIC [On/Off]
ACTIVE TEST
Test Item
Description
This test is able to check Intelligent Key identification number [Off/ID No1/ID N02/ID No3/ID
No4/ID No5].
INT LAMP
FLASHER
HORN
BATTERY SAVER
TRUNK/BACK DOOR
OUTSIDE BUZZER
This test is able to check Intelligent Key warning buzzer operation [On/Off].
INSIDE BUZZER
This test is able to check combination meter warning chime operation [Take Out/Knob/Key/
Off].
INDICATOR
This test is able to check combination meter warning lamp operation [KEY ON/KEY IND/Off].
IGN CONT2
ENGINE SW ILLUMI
This test is able to check push-button ignition switch START indicator operation [On/Off].
This test is able to check push-button ignition switch indicator operation [On/Off].
ACC CONT
IGN CONT1
BCS-23
BCS
Description
ST CONT LOW
IGNITION RELAY
KEYFOB PW TEST
This test is able to check power window operation using the Intelligent Key [Off/DOWN/UP].
WORK SUPPORT
Support Item
IGN/ACC BATTERY SAVER
ANSWER BACK
Setting
Battery saver function ON.
Off
On*
Off
BUZZER
HORN
Off*
INVALID
On
Off*
On*
Horn chirp reminder when doors are locked with Intelligent Key.
Off
No horn chirp reminder when doors are locked with Intelligent Key.
On
Off*
Description
On*
On*
Off
On*
Off
On*
Off
On
Off*
Start
100 msec
200 msec
End
BCS-24
Setting
MODE7
5 min
MODE6
4 min
MODE5
3 min
Description
MODE4
2 min
MODE3*
1 min
MODE2
30 sec
MODE1
Off
*: Initial Setting
COMB SW
COMB SW : CONSULT Function (BCM - COMB SW)
INFOID:0000000009462007
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
FR WASHER SW [On/Off]
G
Description
FR WIPER HI [On/Off]
FR WIPER LOW [On/Off]
HI BEAM SW [On/Off]
PASSING SW [On/Off]
FR FOG SW [On/Off]
BCS
BCM
BCM : CONSULT Function (BCM - BCM)
INFOID:0000000009462008
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
ECU IDENTIFICATION
The BCM part number is displayed.
WORK SUPPORT
Revision: November 2013
BCS-25
Setting
Description
Reset
Cancel
CONFIGURATION
Refer to BCS-65, "CONFIGURATION (BCM) : Description".
IMMU
INFOID:0000000009462009
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
DONE indicates the number of Intelligent Key ID which has been registered.
TP 1 [Yet/DONE]
PUSH SW [On/Off]
ACTIVE TEST
Test Item
THEFT IND
Description
This test is able to check security indicator operation [On/Off].
BATTERY SAVER
BATTERY SAVER : CONSULT Function (BCM - BATTERY SAVER)
INFOID:0000000009462010
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
BCS-26
Description
PUSH SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
Indicates condition of unlock signal from door lock and unlock switch.
RKE-LOCK [On/Off]
RKE-UNLOCK [On/Off]
ACTIVE TEST
G
Test item
BATTERY SAVER
Description
This test is able to check battery saver operation [On/Off].
TRUNK
TRUNK : CONSULT Function (BCM - TRUNK)
INFOID:0000000009462011
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Description
Indicates vehicle speed signal received from ABS on CAN communication line.
TR CANCEL SW [On/Off]
RKE-TR/BD [On/Off]
BCS
THEFT ALM
INFOID:0000000009462012
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
BCS-27
Description
PUSH SW [On/Off]
Indicates condition of lock signal from door lock and unlock switch.
Indicates condition of unlock signal from door lock and unlock switch.
RKE-LOCK [On/Off]
RKE-UNLOCK [On/Off]
RKE-TR/BD [On/Off]
ACTIVE TEST
Test Item
FLASHER
Description
This test is able to check turn signal lamp operation [LH/RH/Off].
THEFT IND
HEADLAMP(HI)
WORK SUPPORT
Support Item
SECURITY ALARM SET
Setting
Description
On
Off
RETAINED PWR
RETAINED PWR : CONSULT Function (BCM - RETAINED PWR)
INFOID:0000000009462013
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Monitor Item [Unit]
Description
SIGNAL BUFFER
Revision: November 2013
BCS-28
INFOID:0000000009462014
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
DATA MONITOR
Description
Indicates condition of the push-button ignition switch.
INFOID:0000000009462015
CAUTION:
After disconnecting the CONSULT vehicle interface (VI) from the data link connector, the ignition must
be cycled OFF ON (for at least 5 seconds) OFF. If this step is not performed, the BCM may not go
to sleep mode, potentially causing a discharged battery and a no-start condition.
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS transmitter IDs
Display tire pressure reported by the TPMS transmitter
Read TPMS DTCs
Register TPMS transmitter IDs
DATA MONITOR
Monitor Item [Unit]
2
Description
BUZZER [Off/On]
BCS
ACTIVE TEST
Test Item
Description
FLASHER
HORN
BCS-29
Description
WARNING LAMP
This test is able to check tire pressure warning lamp operation [On/Off].
ID REGIST WARNING
WORK SUPPORT
Support Item
Description
ID READ
ID REGIST
BCS-30
INFOID:0000000009462016
NOTE:
The Signal Tech II Tool (J-50190) can be used to perform the following functions. Refer to the Signal Tech II
User Guide for additional information.
Activate and display TPMS transmitter IDs
Display tire pressure reported by the TPMS transmitter
Read TPMS DTCs
Register TPMS transmitter IDs
Check Intelligent Key relative signal strength
Confirm vehicle Intelligent Key antenna signal strength
Condition
Value/Status
STOP
Off
On
Off
A/C switch ON
On
AIR PRESS FL
AIR PRESS FR
AIR PRESS RL
AIR PRESS RR
sec
Off
On
Off
On
AIR COND SW
AUTO LIGHT SW
BRAKE SW 1
BRAKE SW2
BUZZER
CDL LOCK SW
CDL UNLOCK SW
CONFRM ID ALL
CONFIRM ID4
CONFIRM ID3
On
Off
Off
On
Off
On
Off
BCS
On
Off
On
Yet
DONE
The key ID does not match the fourth key ID registered to BCM.
Yet
DONE
The key ID does not match the third key ID registered to BCM.
Yet
DONE
BCS-31
CONFIRM ID1
Condition
Value/Status
The key ID does not match the second key ID registered to BCM.
Yet
DONE
The key ID does not match the first key ID registered to BCM.
Yet
DONE
CRANKING TME
sec
sec
Off
On
Off
On
Off
On
Off
On
LOCK
UNLK
READY
LOCK
DETE SW -IPDM
DETE SW PWR
DETE/CANCL SW
DOOR STAT-AS
DOOR STAT-DR
DOOR STAT-RL
DOOR STAT-RR
DOOR SW-AS
DOOR SW-BK
DOOR SW-DR
DOOR SW-RL
DOOR SW-RR
ENGINE STATE
FAN ON SIG
FR FOG SW
UNLK
READY
LOCK
UNLK
READY
LOCK
UNLK
READY
Off
On
Trunk closed
Off
Trunk opened
On
Off
On
Off
On
Off
On
Engine stopped
STOP
STALL
At engine cranking
CRANK
Engine running
RUN
Off
On
Off
On
BCS-32
FR WIPER LOW
FR WIPER HI
FR WIPER INT
FR WIPER STOP
HAZARD SW
HEAD LAMP SW 1
HEAD LAMP SW 2
HI BEAM SW
ID AUTHENT CANCEL TIMER
ID OK FLAG
ID REGST FL1
ID REGST FR1
ID REGST RL1
ID REGST RR1
PASSING SW
Condition
Value/Status
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
STOP
Reset
Set
YET
DONE
YET
DONE
YET
DONE
YET
DONE
Off
Ignition switch ON
On
1-7
I-Key OFF
Key OFF
I-Key ON
Key ON
Off
On
Off
On
Close to 5V
Close to 0V
Close to 5V
Close to 0V
Off
On
BCS-33
BCS
Condition
Value/Status
Reset
Set
Reset
Set
Reset
Set
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
0-19
0-19
Off
On
Off
On
PUSH SW
PUSH SW-IPDM
REAR DEF SW
REQ SW-AS
REQ SW-DR
REQ SW-BD/TR
RKE-LOCK
RKE-MODE CHG
RKE-PANIC
RKE-P/W OPEN
RKE-TR/BD
RKE-UNLOCK
SFT N-MET
SFT P-MET
SFT PN -IPDM
SFT PN/N SW
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
BCS-34
TP 4
Condition
Value/Status
Off
On
Yet
DONE
Yet
DONE
Yet
DONE
Yet
DONE
Off
On
Off
On
Off
On
Off
On
Off
On
Off
On
VEH SPEED 1
mph, km/h
VEH SPEED 2
mph, km/h
Off
On
TP 3
TP 2
TP 1
TR CANCEL SW
TR/BD OPEN SW
TRNK/HAT MNTR
TURN SIGNAL L
TURN SIGNAL R
UNLK SEN-DR
WARNING LAMP
BCS
BCS-35
AWMIA1310ZZ
PHYSICAL VALUES
BCS-36
Description
Signal name
(+)
(-)
1
(R)
Ground
3
(BR)
Ground
4
(Y)
Ground
Input/
Output
Condition
Value
(Approx.)
0V
Input
Pressed
Output
OFF
0V
ACC or ON
5V
Input
Not pressed
Battery voltage
Close to 5V
Close to 0V
OFF
D
0V
TURN RH
10
(W)
Ground
Combination switch
input 5
Input
Combination
switch
(Wiper intermittent dial 4)
HEADLAMP 1
HI BEAM
TAIL LAMP
G
PKIB4958J
1.0V
OFF
0V
TURN LH
11
(BG)
Ground
Combination switch
input 4
Input
Combination
switch
(Wiper intermittent dial 4)
PASSING
HEADLAMP 2
FR FOG
PKIB4958J
1.0V
OFF
0V
FR WIPER LOW
12
(W)
Ground
Combination switch
input 3
Input
Combination
switch
(Wiper intermittent dial 4)
FR WIPER INT/AUTO
AUTO LIGHT
BCS
PKIB4958J
1.0V
OFF
0V
FR WASHER
13
(G)
Ground
Combination switch
input 2
Input
Combination
switch
(Wiper intermittent dial 4)
O
INT VOLUME 3
P
PKIB4958J
1.0V
BCS-37
(-)
Description
Signal name
Value
(Approx.)
Condition
Input/
Output
OFF
0V
FR WIPER HI
14
(P)
Ground
Combination switch
input 1
Input
Combination
switch
(Wiper intermittent dial 4)
INT VOLUME 1
INT VOLUME 2
PKIB4958J
1.0V
17
(B)
Ground
Input
0V
ON
18
(G)
Ground
Security indicator
Output
Security indicator
0V
Blinking
JPMIA0014GB
11.3V
19
(G)
Ground
Input
Door lock/unlock
switch
20
(W)
Ground
Shift P
Input
Selector lever
21
(W)
Ground
Output
Step lamp
23
(L)
Ground
Compressor ON signal
Input
A/C switch
24
(G)
Ground
Input
Key cylinder
switch
25
(BG)
Ground
Input
26
(Y)
Ground
Shorting input
Input
27
(G)
Ground
29
(Y)
Ground
Input
Input
OFF
Battery voltage
Lock
Battery voltage
Unlock
0V
P position
0V
0V
OFF
Battery voltage
OFF
9.0 - 12.0V
ON
0V
OFF (neutral)
5V
ON (unlock)
0V
Battery voltage
Battery voltage
Battery voltage
0V
Battery voltage
ON
Battery voltage
OFF
0V
BCS-38
(-)
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
30
(P)
Ground
Input
Front door LH
LOCK status
JPMIA0011GB
11.8V
32
(Y)
Ground
Input
UNLOCK status
0V
OFF
5V
ON
0V
F
33
(G)
Ground
Input
CANCEL
G
JPMIA0012GB
1.1V
ON
34
(BG)
Ground
Input
Door lock/unlock
switch
Unlock
0V
Battery voltage
Lock
0V
Pressed
0V
J
36
(Y)
Ground
Hazard switch
Input
Hazard switch
Not pressed
JPMIA0012GB
1.1V
39
(L)
Ground
Shift N/P
Input
Selector lever
P or N position
Except P and N positions
Battery voltage
0V
ON
5.5V
OFF
0V
48
(BR)
Ground
Output
52
(G)
Ground
Audio dongle
Input/
Output
BCS
N
5V
54
(P)
Ground
Input/
Output
ON
JPMIA0013GB
10.2V
OFF or ACC
59
(P)
Ground
CAN low
Input/
Output
BCS-39
0V
Description
Signal name
Input/
Output
(+)
(-)
60
(L)
Ground
CAN high
Input/
Output
61
(Y)
Ground
Output
62
(BR)
Ground
Output
Condition
Value
(Approx.)
Active
Battery voltage
Not activated
0V
Battery voltage
0V
0V
64
(W)
Ground
Buzzer output
Output
Outside warning
buzzer
Sounding
Not sounding
Battery voltage
66
(R)
Ground
Output
OFF or ACC
0V
OFF or ACC
67
(W)
68
(P)
Ground
Ground
Output
Output
69
(L)
Ground
Output
70
(G)
Ground
Output
ON
ON
Ground
Input
Battery voltage
0V
Battery voltage
OFF or ACC
ON
ON (pressed)
71
(V)
0V
Battery voltage
Battery voltage
0V
Battery voltage
0V
JPMIA0016GB
1.0V
ON (pressed)
72
(Y)
Ground
Passenger request
switch
Input
0V
JPMIA0016GB
1.0V
BCS-40
(-)
74
(P)
Ground
Description
Signal name
Input/
Output
Input
Condition
Front door lock
assembly LH (key
cylinder switch)
Value
(Approx.)
OFF (neutral)
5V
ON (lock)
0V
C
OFF
75
(BG)
Ground
Combination switch
output 5
Output
Combination
switch
(Wiper intermittent dial 4)
D
PKIB4960J
7.0 8.0V
INT VOLUME 2
F
FR FOG
G
PKIB4958J
1.2V
OFF
76
(W)
Ground
Combination switch
output 4
Output
Combination
switch
(Wiper intermittent dial 4)
PKIB4960J
7.0 8.0V
INT VOLUME 3
AUTO LIGHT
TAIL LAMP
PKIB4958J
1.2V
BCS
BCS-41
(-)
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
OFF
77
(R)
Ground
Combination switch
output 3
Output
Combination
switch
(Wiper intermittent dial 4)
PKIB4960J
7.0 8.0V
INT VOLUME 1
HEADLAMP 2
HI BEAM
PKIB4958J
1.2V
OFF
78
(P)
Ground
Combination switch
output 2
Output
Combination
switch
(Wiper intermittent dial 4)
PKIB4960J
7.0 8.0V
FR WIPER HI
FR WIPER INT/AUTO
PASSING
HEADLAMP 1
PKIB4958J
1.2V
OFF
79
(G)
Ground
Combination switch
output 1
Output
Combination
switch
(Wiper intermittent dial 4)
PKIB4960J
7.0 8.0V
FR WASHER
FR WIPER LOW
TURN LH
TURN RH
PKIB4958J
1.2V
BCS-42
(-)
Ground
Description
Signal name
Output
Value
(Approx.)
Battery voltage
0V
Condition
Input/
Output
trunk
82
(Y)
Ground
Input
Rear door LH
switch
JPMIA0011GB
11.8V
85
(BG)
91
(V)
Ground
Ground
Output
Output
Trunk lid
0V
ON
0V
OFF
Battery voltage
Battery voltage
0V
0V
I
92
(LG)
Ground
Output
PKID0926E
6.5 V
93
(V)
Ground
Input
Rear door RH
switch
BCS
JPMIA0011GB
11.8V
ON (when rear door RH
opens)
0V
94
(SB)
Ground
Passenger door
switch
Input
Front door RH
switch
JPMIA0011GB
11.8 V
ON (when front door RH
opens)
BCS-43
0V
96
(BR)
(-)
Ground
Description
Signal name
Condition
Input/
Output
Input
Front door LH
switch
Value
(Approx.)
JPMIA0011GB
11.8V
ON (front door LH OPEN)
97
(SB)
Ground
Trunk switch
Input
Trunk switch
0V
JPMIA0011GB
11.8V
ON (trunk is open)
0V
99
(G)
Ground
Output
100
(R)
Ground
Output
BCS-44
(-)
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
B
When Intelligent Key is in
the antenna detection area
101
(G)
Ground
Output
JMKIA0062GB
E
When Intelligent Key is not
in the antenna detection
area
F
JMKIA0063GB
102
(W)
Ground
Output
JMKIA0062GB
J
When Intelligent Key is not
in the antenna detection
area
K
JMKIA0063GB
0V
BCS
103
(Y)
Ground
Output
PKID0926E
6.5 V
P
104
(BR)
Ground
Output
R position
PKID0926E
6.5V
Any position other than R
BCS-45
0V
(-)
Description
Signal name
Condition
Input/
Output
105
(BR)
Ground
Output
Value
(Approx.)
0V
PKID0926E
6.5 V
OFF
107
(W)
Ground
Input
0V
NOTE:
When the illumination
brightening/dimming level
is in the neutral position
ON
JSNIA0010GB
108
(BG)
Ground
109
(G)
Ground
Reverse signal
Output
111
(Y)
Ground
ACC LED
Output
113
(P)
Ground
Input
Output
Selector lever
P position
0V
Battery voltage
R position
Battery voltage
OFF
ACC or ON
0V
OFF
0V
ACC or ON
0V
Battery voltage
Battery voltage
114
(P)
Ground
Output
JMKIA0062GB
BCS-46
(-)
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
B
When Intelligent Key is in
the antenna detection area
115
(R)
Ground
Output
JMKIA0062GB
E
When Intelligent Key is not
in the antenna detection
area
F
JMKIA0063GB
116
(W)
Ground
Output
J
When Intelligent Key is not
in the passenger compartment
K
JMKIA0063GB
0V
BCS
117
(SB)
Ground
Output
PKID0926E
6.5 V
BCS-47
(-)
Description
Signal name
Condition
Input/
Output
Value
(Approx.)
Standby state
OCC3881D
119
(G)
Ground
Input/
Output
OCC3880D
121
(R)
Ground
Output
JMKIA0062GB
122
(P)
Ground
Output
JMKIA0062GB
BCS-48
127
(L)
Description
Signal name
Input/
Output
Ground
Input/
Output
Ground
Input/
Output
(-)
Value
(Approx.)
During waiting
During waiting
Condition
F
JMKIA0062GB
128
(BG)
Ground
Output
G
When Intelligent Key is not
in the passenger compartment
JMKIA0063GB
129
(G)
Ground
130
(SB)
Ground
131
(W)
Ground
132
(L)
133
(Y)
134
(B)
Ground
Ground
Ground
135
(BR)
Ground
136
(P)
Ground
Ground 2
Output
Output
Input
Output
Output
Driver, passenger
and fuel door lock
Output
Output
After passing the interior room lamp battery saver operation time
Any other time after passing the interior room
lamp battery saver operation time
Front door RH
All doors
Rear door RH
and rear door LH
Interior room
lamp
J
Battery voltage
Battery voltage
0V
Battery voltage
Battery voltage
0V
Battery voltage
0V
All doors
0V
BCS
0V
Battery voltage
0V
OFF
Battery voltage
ON
0V
BCS-49
Description
(-)
Value
(Approx.)
Condition
Input/
Output
Signal name
Battery voltage
0V
137
(V)
Ground
138
(V)
Ground
Input
Battery voltage
139
(W)
Ground
Input
Battery voltage
140
(LG)
Ground
Output
Battery voltage
141
(V)
Ground
Output
Battery voltage
142
(BR)
Ground
Input
Battery voltage
143
(B)
Ground
Ground 1
0V
Output
Front door LH
Fail Safe
Display contents of CONSULT
INFOID:0000000009462017
Fail-safe
Cancellation
Erase DTC
Erase DTC
Erase DTC
Erase DTC
B2195: ANTI-SCANNING
B2562: LO VOLTAGE
100 ms after the power supply voltage increases to more than 8.8 V
1 second after the starter motor relay control inside BCM becomes
normal
B2618: BCM
1 second after the ignition relay (IPDM E/R) control inside BCM becomes normal
BCM initialization
INFOID:0000000009462018
If some DTCs are displayed at the same time, perform inspections one by one based on the following priority
chart.
BCS-50
DTC
BCS
BCS-51
DTC
DTC Index
INFOID:0000000009462019
NOTE:
Details of time display
CRNT: Displays when there is a malfunction now or after returning to the normal condition until turning ignition switch OFF ON again.
1 - 39: Displayed if any previous malfunction is present when current condition is normal. It increases like 1
2 3...38 39 after returning to the normal condition whenever ignition switch OFF ON. The counter
remains at 39 even if the number of cycles exceeds it. It is counted from 1 again when turning ignition switch
OFF ON after returning to the normal condition if the malfunction is detected again.
CONSULT display
No DTC is detected.
Further testing may be required.
Fail-safe
Intelligent Key
warning lamp
ON
Tire pressure
monitor warning
lamp ON
Reference page
BCS-68, "Description"
BCS-70, "Description"
SEC-84, "Description"
SEC-86, "Description"
BCS-52
Intelligent Key
warning lamp
ON
Tire pressure
monitor warning
lamp ON
Reference page
SEC-90, "Description"
SEC-100, "Description"
B2604: PNP SW
B2605: PNP SW
SEC-118, "Description"
B2618: BCM
CONSULT display
(Turn ON for
15 seconds)
SEC-120, "Description"
B26F6: BCM
BCS-53
BCS
P
WT-30, "DTC Logic"
Intelligent Key
warning lamp
ON
Tire pressure
monitor warning
lamp ON
CONSULT display
Reference page
BCS-54
BCM
[BCM]
WIRING DIAGRAM
BCM
Wiring Diagram
INFOID:0000000009462020
BCS
ABMWA2163GB
BCS-55
BCM
[BCM]
ABMWA2164GB
BCS-56
BCM
[BCM]
BCS
O
ABMWA2165GB
BCS-57
BCM
[BCM]
ABMWA2170GB
BCS-58
BCM
[BCM]
BCS
O
ABMWA2166GB
BCS-59
BCM
[BCM]
ABMWA1575GB
BCS-60
BCM
[BCM]
BCS
O
ABMIA5106GB
BCS-61
BCM
[BCM]
AAMIA1489GB
BCS-62
BCM
[BCM]
BCS
O
ABMIA5107GB
BCS-63
BASIC INSPECTION
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000009462021
BEFORE REPLACEMENT
When replacing BCM, save or print current vehicle specification with CONSULT configuration before replacement.
NOTE:
If Before Replace ECU cannot be used, use the After Replace ECU or Manual Configuration after replacing BCM.
AFTER REPLACEMENT
CAUTION:
When replacing BCM, you must perform After Replace ECU with CONSULT.
- Complete the procedure of After Replace ECU in order.
- If you set incorrect After Replace ECU, incidents might occur.
- Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
When replacing BCM, perform the system initialization (NATS).
2.REPLACE BCM
>> GO TO 4.
CONFIGURATION (BCM)
Revision: November 2013
BCS-64
INFOID:0000000009462023
Vehicle specification needs to be written with CONSULT because it is not written after replacing BCM.
Configuration has three functions as follows:
Function
Description
CAUTION:
When replacing BCM, you must perform Select Saved Data List or "After Replace ECU" with CONSULT.
Complete the procedure of Select Saved Data List or "After Replace ECU" in order.
If you set incorrect Select Saved Data List or "After Replace ECU", incidents might occur.
Configuration is different for each vehicle model. Confirm configuration of each vehicle model.
Never perform Select Saved Data List or "After Replace ECU" except for new BCM.
INFOID:0000000009462024
CONSULT
Select Reprogramming, Configuration of BCM.
H
CONSULT
Automatically Operation Log Selection window will display if Before Replace ECU was performed. Select
applicable file from the Save Data List and press Confirm.
>> GO TO 4.
4.OPERATION CHECK
Confirm that each function controlled by BCM operates normally.
>> Work End.
Revision: November 2013
BCS-65
INFOID:0000000009462025
CAUTION:
Thoroughly read and understand the vehicle specification. Incorrect settings may result in abnormal
control of ECU.
MANUAL SETTING ITEM
Items
Setting value
AUTO LIGHT
FR FOG LAMP
TIRE PRESSURE
BCM AC CONTROL
MODE1 MODE2
ENST/LCK/UNLCK/ALRM ENST/LCK/UNLCK/BD/ALRM
ENST/LCK/UNLCK/TRK/ALRM LCK/UNLCK/PBD/ALRM
LCK/UNLCK/ALRM LCK/UNLCK/PBD LCK/UNLCK/TRNK
LCK/UNLCK LCK/UNLCK/TRNK/ALRM
BCS-66
Description
INFOID:0000000009462026
BCM is in transit mode if turn signal indicator on combination meter turns ON for 1 minute when ignition
switch is turned from OFF to ON.
In this case, cancel operation must be performed.
NOTE:
Do not cancel transit mode during storage of the vehicle. Always cancel transit mode before delivery of the
vehicle to customer.
Work Procedure
INFOID:0000000009462027
BCS
BCS-67
DTC/CIRCUIT DIAGNOSIS
U1000 CAN COMM CIRCUIT
Description
INFOID:0000000009462028
DTC Logic
INFOID:0000000009462029
Possible cause
Diagnosis Procedure
INFOID:0000000009462030
BCS-68
DTC Logic
INFOID:0000000009462031
CONSULT Display
Possible Cause
BCM
Diagnosis Procedure
INFOID:0000000009462032
1. REPLACE BCM
When DTC U1010 is detected, replace BCM.
BCS
BCS-69
INFOID:0000000009462033
U0415 is displayed if any unusual condition is present in the reception status of the vehicle speed signal from
the ABS actuator and electric unit (control unit).
DTC Logic
INFOID:0000000009462034
Possible Cause
ABS system
Combination meter system
CAN bus harness
1. DTC CONFIRMATION
1.
2.
3.
Diagnosis Procedure
INFOID:0000000009462035
1. ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) SELF DIAGNOSTIC RESULT
Perform Self Diagnostic Result of ABS with CONSULT. Refer to BRC-33, "CONSULT Function (ABS)".
Is any DTC detected?
YES >> Perform the trouble diagnosis related to the detected DTC. Refer to BRC-45, "DTC Index".
NO
>> GO TO 2.
2. CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND
CIRCUIT
Check ABS actuator and electric unit (control unit) power and ground. Refer to BRC-70, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace harness or connectors.
Perform Self Diagnostic Result of METER M&A with CONSULT. Refer to MWI-18, "CONSULT Function
(METER/M&A)".
Is any DTC detected?
YES >> Perform the trouble diagnosis related to the detected DTC. Refer to MWI-27, "DTC Index".
NO
>> Refer to GI-43, "Intermittent Incident".
BCS-70
DTC Logic
INFOID:0000000009462036
B
DTC Detection Condition
Possible cause
Harness or connector (power supply circuit)
Vehicle battery
1.
2.
3.
1. DTC CONFIRMATION
Erase DTC.
Turn ignition switch OFF.
Perform the Self Diagnostic Result of BCM with CONSULT, after the ignition switch has been turned ON
for 120 seconds or more.
Is any DTC detected?
YES >> Refer to BCS-71, "Diagnosis Procedure".
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009462037
Check BCM power supply and ground circuit. Refer to BCS-74, "Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 3.
NO
>> Repair or replace harness or connectors.
L
Perform Self Diagnostic Result of BCM with CONSULT. Refer to BCS-25, "BCM : CONSULT Function (BCM BCM)".
Is DTC B2562 CRNT?
BCS
YES >> Replace BCM. Refer to BCS-80, "Removal and Installation".
NO
>> Refer to GI-43, "Intermittent Incident".
N
BCS-71
INFOID:0000000009462038
Possible cause
Harness or connector (power supply circuit)
1. DTC CONFIRMATION
1.
2.
3.
Erase DTC.
Turn ignition switch OFF.
Perform the Self Diagnostic Result of BCM with CONSULT, after the ignition switch has been turned ON
for 2 minutes or more.
Is any DTC detected?
YES >> Refer to BCS-72, "Diagnosis Procedure".
NO
>> Inspection End.
Diagnosis Procedure
INFOID:0000000009462039
1. CHECK FUSE
Check that the following fuse is not blown.
Terminal No.
Signal name
Fuse No.
131
1 (10A)
1.
2.
Terminal
M21
131
Ground
Voltage
(Approx.)
Battery voltage
1.
2.
BCS-72
BCM
Connector
Terminal
M21
129
Ground
Continuity
No
BCS
BCS-73
INFOID:0000000009462040
Signal name
139
I (40A)
131
1 (10A)
1.
2.
Terminal
131
M21
139
Ground
Voltage
(Approx.)
Battery voltage
Check continuity between BCM connector M21 terminals 134, 143 and ground.
BCM
Connector
M21
Terminal
134
143
Ground
Continuity
Yes
BCS-74
Diagnosis Procedure
INFOID:0000000009462041
BCM
Connector
Combination switch
Terminal
Connector
Terminal
INPUT 1
79
11
INPUT 2
78
INPUT 3
M18
77
M28
INPUT 4
76
10
INPUT 5
75
13
Continuity
F
Yes
BCM
Connector
Continuity
Terminal
INPUT 1
79
INPUT 2
78
INPUT 3
M18
77
INPUT 4
76
INPUT 5
75
No
BCS
BCM
Connector
Terminal
INPUT 1
79
INPUT 2
78
INPUT 3
M18
77
INPUT 4
76
INPUT 5
75
Ground
BCS-75
O
Ground
Voltage
BCS-76
[BCM]
Diagnosis Procedure
INFOID:0000000009462042
BCM
Connector
Combination switch
Terminal
Connector
Terminal
OUTPUT 1
14
12
OUTPUT 2
13
14
OUTPUT 3
M17
12
M28
OUTPUT 4
11
OUTPUT 5
10
Continuity
F
Yes
BCM
Connector
Continuity
Terminal
OUTPUT 1
14
OUTPUT 2
13
OUTPUT 3
M17
12
OUTPUT 4
11
OUTPUT 5
10
No
BCS
BCM
Connector
Terminal
OUTPUT 1
14
OUTPUT 2
13
OUTPUT 3
M17
12
OUTPUT 4
11
OUTPUT 5
10
Ground
BCS-77
O
Ground
Voltage
BCS-78
[BCM]
SYMPTOM DIAGNOSIS
INFOID:0000000009462043
Perform the data monitor of CONSULT to check for any malfunctioning item.
Check the malfunction combinations.
Malfunction item:
FR FOG SW
AUTO LIGHT SW
PASSING SW
HEAD LAMP SW 2
HEAD LAMP SW 1
HI BEAM SW
TAIL LAMP SW
All Items
If only one item is detected or the item is not applicable to the combinations A to K
Identify the malfunctioning part from the agreed combination and repair or replace the part.
Malfunction
combination
Malfunctioning part
Repair or replace
BCS
Inspect the combination switch output circuit applicable to the malfunctioning part. Refer to BCS-77, "Diagnosis Procedure".
BCM
Combination switch
I
J
3.
G
H
TURN SIGNAL L
TURN SIGNAL R
INT VOLUME
FR WIPER INT/AUTO
FR WASHER SW
FR WIPER LOW
Malfunction combination
FR WIPER HI
BCS-79
INFOID:0000000009462044
REMOVAL
CAUTION:
Before replacing BCM, perform "READ CONFIGURATION" to save or print current vehicle specification. Refer to BCS-64, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
1. Disconnect the negative battery terminal. Refer to PG-73, "Removal and Installation (Battery)".
2. Remove the combination meter. Refer to MWI-82, "Removal and Installation".
3. Remove the BCM screws (A) and pull out the BCM (1).
4. Disconnect the harness connectors from the BCM (1) and
remove.
ALMIA0580ZZ
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
Be sure to perform "WRITE CONFIGURATION" when replacing BCM. Refer to BCS-65, "CONFIGURATION (BCM) : Description".
Be sure to perform the system initialization (NATS) when replacing BCM. Refer to BCS-64, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description".
When replacing BCM, if new BCM does not come with keyfobs attached, all existing keyfobs must be
re-registered.
BCS-80
COMBINATION SWITCH
[BCM]
COMBINATION SWITCH
Exploded View
INFOID:0000000009462045
F
AWMIA1293ZZ
1.
Combination switch
2.
Front
NOTE:
Shown with the steering wheel removed for clarity only.
H
INFOID:0000000009462046
REMOVAL
CAUTION:
Before servicing, turn the ignition switch OFF, disconnect both battery terminals and wait at least
three minutes.
Do not use air tools or electric tools for servicing.
1. Disconnect both the negative and positive battery terminals, then wait at least three minutes. Refer to PG73, "Removal and Installation (Battery)".
2. Remove the steering column covers. Refer to IP-17, "Removal and Installation".
3. Rotate steering wheel clockwise to access first combination switch bolt and remove.
4. Rotate steering wheel counter-clockwise to access second combination switch bolt and remove.
5. Disconnect the harness connector from the combination switch and remove.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After the work is completed, make sure no system malfunction is detected by air bag warning lamp.
In case a malfunction is detected by the air bag warning lamp, reset with the self-diagnosis function
and delete the memory with CONSULT.
If a malfunction is still detected after the above operation, perform self-diagnosis to repair malfunctions. Refer to SRC-42, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair
Requirement".
BCS
BCS-81