You are on page 1of 6

GROUP STUDY - TRANSMISSION LINES

1. Transmission media are usually categorized as


a. Fixed or unfixed
c. guided or unguided
b. Determinate or indeterminate
d. metallic or non-metallic
2. Both twisted pair cable and coaxial cable transmit data in the form of
a. Light
b. electric current
c. induction d. heat
3. It is the input impedance of a transmission line either infinitely long or
terminated in a pure resistance equal to the line impedance.
a. Characteristic impedance
c. source impedance
b. Load impedance
d. Iterative Impedance
4. The characteristic impedance of a transmission line does not depend on its
a. Length b. conductor spacing
c. conductor diameter
d. dielectric
constant
5. How many 600kHz waves can be on a 5 mile transmission line
simultaneously?
a. 16.13
b. 18
c. 20.25
d. 15.25
6. The transmission lines that permit most efficient transfer of microwave
energy are
a. Cavity resonators
b. faraday screen c. waveguide
d. coaxial
cable
7. Determine the characteristic impedance of a coaxial cable with an inductance
of 0.2uH/ft and capacitance of 16pF/ft.
a. 50 ohms
b. 60 ohms c. 81.2 ohmsd. 111.8 ohms
8. If the 2 towers of a 2MHz antenna are separated by 120 electrical degrees,
what is the tower separation in feet?
a. 150
b. 250
c. 500
d. 650
9. Which of the following is a major source of loss in a transmission line?
a. Dielectric heating
b. radiation c. conductor heating
d. all of
these
10.The tendency of electrons to confine their travel near the surface of the solid
conductor as the frequency of operation increases.
a. Capture effect b. Doppler effect c. skin effect
d. flywheel effect
11.The fixed voltage and current wave patterns that result in a resonant
transmission line due to the vector addition of the incident and reflected
travelling waves.
a. Radio waves
b. electric waves c. magnetic waves d. standing
waves
12.It is the ratio of the maximum voltage to the minimum voltage of a standing
wave on a transmission line
a. SWR
b. TDR
c. Reflection Coefficient
d.
F/B ratio
13.A flat line is considered to have an SWR of
a. 1:1
b. 1:2
c. 1:0
d. 1:infinity
14.What is the reflection coefficient for a transmission line with incident voltage
of 4 v and reflected voltage of 0.75v?
a. 20
b. 2
c. 0.2
d. 5
15.If a 75 ohm transmission line is terminated with the load resistance of 50
ohms, what is the SWR along the line?
a. 1.5
b. 0.67
c. 5
d. 12
16.Voltage minima are called
a. Anti nodes
b. nodes
c. peak
d. lowest value
17.A transmission line is connected to a mismatch load. Calculate the VSWR
decibel equivalent if the reflection coefficient is 0.25.
a. 2.15 dB
b. 4.44 dB c. 8.6 dB
d. 5 dB
18.The person responsible in publishing graphical device for solving transmission
line problems.
a. Charles Smith b. Philip Smith
c. Smith Chart
d. James Smith

19.For the coaxial line, the thickness of the outer conductor is 0.125 while the
outer conductor diameter is 1.25 and the diameter of the inner conductor is
0.75. Solve for the characteristic Impedance of the line.
a. 17.24 ohms
b. 30.6 ohms
c. 75 ohms d. 74.5 ohms
20.Determine the characteristic impedance of a quarter wave matching section
which will eliminate standing waves and thereby provide a matched condition
for a 300 ohm resistive load fed from a 72 ohm transmission line.
a. 50 ohms
b. 75 ohms c. 150 ohms
d. 300 ohms
21.A transformer used to match a balanced transmission line to an unbalanced
line
a. Auto transformer
b. stub
c. quarter wave stub
d.
balun
22.A form of transmission line used at high UHF and microwave frequencies
sandwiched between 2 ground planes and separated from each by a
dielectric.
a. Stripline
b. microstrip c. coaxial line
d. twin lead
23.A shorted transmission line less than quarter wavelength will exhibit ____
reactance
a. Inductive
b. capacitive c. series LC d. parallel LC
24.A transmission line consisting of center conductor, a plastic insulation, a fine
wire braid shield and outer plastic insulation as a jacket.
a. Coaxial cable b. twin lead c. waveguide
d. twisted pair
25.RJ45 is the common connector used in what type of transmission line?
a. Flat wire
b. twisted pair
c. coaxial cable
d. shielded pair
26.SWR stands for:
a. Shorted Wave Radiation
c. Shorted Wire Region
b. Sine Wave Response
d. none of the above
27.An example of an unbalanced line is:
a. a coaxial cable
c. an open-wire-line cable
b. 300-ohm twin-lead TV cable d. all of the above
28.The characteristic impedance of a cable depends on:
a. the resistance per foot of the wire used
b. the resistance per foot and the inductance per foot
c. the resistance per foot and the capacitance per foot
d. the inductance per foot and the capacitance per foot
29.For best matching, the load on a cable should be:
a. lower than Z0
b. equal to Z0
c. higher than Z0 d. 50 ohms
30.The characteristic impedance of a cable:
a. increases with length
c. increases with voltage
b. increases with frequency
d. none of the above
31.The velocity factor of a cable depends mostly on:
a. the wire resistance
c. the inductance per foot
b. the dielectric constant
d. all of the above
32.The optimum value for SWR is:
a. zero
b. as large as possible
c. one
d. there is
no optimum value
33.A non-optimum value for SWR will cause:
a. standing waves
c. higher voltage peaks on cable
b. loss of power to load
d. all of the above
34.VSWR stands for:
a. variable SWR
b. voltage SWR
c. vacuum SWR
d.
none of the above
35.A Smith Chart is used to calculate:
a. transmission line impedances c. optimum length of a transmission
line
b. propagation velocity
d. transmission line losses
36.A balanced load can be connected to an unbalanced cable:
a. directly
b. by using a "balun" c. by using a filter d. cannot be
connected

37.Parallel lines are usually operated as ____________________ lines since both


wires are symmetrical with respect to ground.
a. Open wire
b. unbalanced
c. symmetrical
d.
balanced
38.Normally, a transmission line is terminated with a load equal to its
____________________ impedance.
a. characteristic
b. balanced
c. unbalanced
d.
symmetrical
39.Twisted-pair cables are transmission lines for relatively ____________________
frequencies.
a. high
b. low
c. radio
d. microwave
40.The increase of a wire's resistance with frequency is called the
____________________ effect.
a. capture
b. flywheel
c. skin
d. end
41.The inductance and capacitance of a cable are given per unit
____________________.
a. meter
b. frequency
c. foot
d. length
42.A cable that is terminated in its characteristic impedance is called a
____________________ line.
a. resistive
b. matched
c. non resonant
d. all of
these
43.The ideal value for SWR is ____________________.
a. one
b. zero
c. infinity
d.
none of these
44.Short transmission-line sections called ____________________ can be used as
capacitors or inductors.
a. wave impedances
b. quarter wave lines
c. stubs
d. short circuits
45.A ____________________ wavelength transmission line can be used a
transformer.
a. one quarter
b. one half
c. full
d. one
fourth
46.A transmission line has 2.5 pF of capacitance per foot and 100 nH of
inductance per foot. Calculate Its characteristic impedance.
a. 300 ohms
b. 150 ohms
c. 175 ohms
d. 200
ohms
47.Two wires with air as a dielectric are one inch apart. The diameter of the wire
is .04 inch. Calculate, approximately, its characteristic impedance.
a. 300 ohms
b. 200 ohms
c. 400 ohms
d. 386
ohms
48.If a coaxial cable uses plastic insulation with a dielectric constant r = 2.6 ,
what is the velocity factor for the cable?
a. 0.75
b. 1.3
c. 0.5
d. 0.62
49.A cable has a VSWR of 10. If the minimum voltage along the cable is 20 volts,
what is the maximum voltage along the cable?
a. 200 volts
b. 100 volts
c. 80 volts
d. 400 volts
50.A lossless line has a characteristic impedance of 50 ohms, but is terminated
with a 75-ohm resistive load. What SWR do you expect to measure?
a. 1.25
b. 1.5
c. 1.75
d. 2
51.If a cable has an SWR of 1.5, what will be the absolute value of its voltage
coefficient of reflection?
a. 2
b. 1.5
c. 0.2
d. 0.1
52.The most commonly used transmission line is a
a. two-wire balanced line b. single wire
c. three-wire line d.
coax
53.The characteristic impedance of a transmission line does not depend upon its
a. length
b. conductor diameter
c. conductor spacing
d.
none of the above
54.Which of the following is not a common transmission line impedance?

a. 50

b. 75

c. 120

d. 300

55.For maximum absorption of power at the antenna, the relationship between


the characteristic impedance of the line ZO and the load impedance Zl should
be
a. ZO = Zl
b. ZO > Zl
c. ZO < Zl
d. ZO = 0
56.The mismatch between antenna and transmission line impedances cannot be
corrected for by
a. using an LC matching network
b. adjusting antenna length
c. using a balun
d. adjusting the length of
transmission line
57.A pattern of voltage and current variations along a transmission line not
terminated in its
characteristic impedance is called
a. an electric field b. radio waves
c. standing waves
d. a
magnetic field
58.The desirable SWR on a transmission line is
a. 0
b. 1
c. 2
d. infinity
59.A 50 coax is connected to a 73 antenna. The SWR is
a. 0.685
b. 1
c. 1.46
d. 2.92
60.The most desirable reflection coefficient is
a. 0
b. 0.5
c. 1
d. infinity
61.A ratio expressing the percentage of incident voltage reflected on a
transmission line is known as the
a. velocity factor b. standing wave ratio
c. reflection coefficient
d. line efficiency
62.The minimum voltage along a transmission line is 260 V, while the maximum
voltage is 390 V. The SWR is
a. 0.67
b. 1.0
c. 1.2
d. 1.5
63.Three feet is one wavelength at a frequency of
a. 100 MHz
b. 164 MHz
c. 300 MHz
d. 328 MHz
64.At very high frequencies, transmission lines are used as
a. tuned circuits b. antennas
c. insulators
d. resistors
65.A shorted quarter-wave line at the operating frequency acts like a(n)
a. series resonant circuit b. parallel resonant circuit c. capacitor d.
inductor
66.A shorted half-wave line at the operating frequency acts like a(n)
a. capacitor b. inductor c. series resonant circuit
d. parallel resonant
circuit
67.The chief advantage of coaxial cable over open-wire line is
a. Minimized radiation losses
b. Low cost
c. Low noise pick up
d. Low resistive losses
68.The ratio of actual velocity to free-space velocity is called
a. Velocity factor
b. Relative dielectric constant
c. Velocity of propagation
d. Delay time
69.In a balanced line, the same current flows in each line but is
a. 45 out of phase
b. 90 out of phase
c. 180 out of phase
d. 270 out of phase
70.What is the length of a quarter-wavelength section of RG-8A/U coaxial cable
at a frequency of 144.2 Mhz if its velocity factor is 0.69.
a. 52.1 cm
b. 35.9 cm
c. 143.6 cm
d. 2.08 m
71.A nonlossy transmission line that is terminated with a resistive load that is
equal to the characteristic impedance of the line
a. Has the same impedance at all points along the line
b. Has a VSWR of 1:1
c. d. Has a reflection coefficient at the load equal to zero
d. All the above
72. A flat line indicates

a. No reflection
b. VSWR = 1
c. No physical imperfections
d. a and b
73.A nonlossy transmission line terminated with a short circuit has an
a. In-phase reflected voltage that is equal in magnitude to the incident
voltage
b. Opposite-phase reflected voltage that is equal in magnitude to
the incident voltage
c. In-phase reflected voltage that is smaller in magnitude than the incident
voltage
d. Opposite-phase reflected voltage that is smaller in magnitude than the
incident voltage
74.A 50- transmission line that has a load impedance of 300 has a VSWR of
a. 6:1
b. 1:6
c. 0.666:1
d. 1.5:1
75.The input impedance of a quarter-wavelength section of a 50- transmission
line that is terminated with a short is
a. 50
b. 0 (a short)
c. Infinite (open) d. 100

76.A device that is used to match an unbalanced transmission line to a balanced


transmission line is called a
a. Quarter-wavelength matching transformer
b. Balun
c. Shorted-stub section
d. Slotted line
77.In practice, the transmission lines are almost connected to antennas that
have a _________.
a. resistive load whose resistance is greater than the characteristic
impedance of the line
b. resistive load whose resistance is less than the characteristic impedance
of the line
c. resistive load at the resonant frequency
d. capacitive load
78.When the transmission line is matched to the load, it
a. transfers maximum current to the load
c. transfers maximum voltage
to the load
b. transfers maximum power to the load
d. reduces the load
current
79.Conventional transmission media include
a. twisted cable pair
b. waveguide
c. fiber optic cable d. all
of these
80.To couple a coaxial line to a parallel wire line, it is best to use a _____
a. slotted line
b. directional coupler
c. balun
d.
quarter
wavelength transformer
81.Impedance inversion may be obtained with
a. an open circuited stub
c. a short circuited stub
b. a quarterwave line
d. a half-wave line
82.To be properly matched, the ratio of maximum to minimum voltage along a
transmission line should be equal to
a. 50
b. 10
c. 2
d. 1
83.When ZL Zo, the power sent down the line toward the load is called the
a. the incident power
c. the reflected power
b.
the power dissipation
d. the carrier power
84.For transmission line load matching over a range of frequencies, it is best to
use a
a. Balun
c.broadband directional coupler
b. double stub
d. single adjustable stub
85.A short section of a transmission line, open or shorted that is used to match
the impedance of the line to that of an antenna or transmitter.
a. slotted line
b. stub
c. wavetrap
d.
lecher wire
86.The property of a material that determines how much electrostatic energy
can be stored per unit volume when voltage is applied.

a. Permeability
b. magnetic effect c. capacitance
d.
permittivity
87.The value of the total opposition of the transmission media to the flow of
electromagnetic field energy is called
a. characteristic impedance b. velocity factor c. standing waves d.
reflected waves
88.When mismatch is great, this power actually cause damage to the transmitter
or the line itself.
a.
the incident power
c. the reflected power
b.
the power dissipation
d. the carrier power
89.The measure of the superiority of a material over vacuum as a path for
magnetic lines of force is
a.
Permittivity
b. permeability
c. conductivity
d. resistivity
90.The number of standing waves on the wire is equal to the length of the wire
divided by a half wavelength. The principle which allows antennas to operate
at different frequencies which are integral multiples of the fundamental
frequency is called __________.
a. harmonic operation
c. decimonic operation
b. electromagnetic reverberation
d. asynchronous operation
91.A coax line has an attenuation of 2.4 dB per 100 ft. The attenuation for 2.75
ft. is ____ dB.
a. 2.4
b. 4.8
c. 3.3
d. 6.6
92.When a quarter wave stub is used to match a 600 ohm antenna to a line of
52 ohms, the impedance of the matching stub must be ________ ohms.
a. 176
b. 200
c. 150
d. 300
93.The characteristic impedance of a transmission line is determined by
a. its length
c. its height above ground
b. its physical construction
d. the operating frequency
94.When the diameter of two conductors of a two-wire transmission line is held
constant, the effect of decreasing the distance between the conductors is to
a. decrease the impedance
c. increase the surge impedance
b. increase radiation resistance
d. decrease SWR
95.Considering a coaxial transmission line, maximum voltage on the line divided
by the minimum voltage equals the
a. characteristic impedance
b. ISWR
c. VSWR
d.
inductive reactance
96.In a transmission line, if the SWR or maximum current to a minimum current
ratio of 2:1, the ratio of the maximum voltage to the minimum voltage is
a. 1:4
b. 4:1
c. 1:2
d. 2:1
97.Transmission lines are either balanced or unbalanced with respect to
a. negative terminal
b. input
c. ground
d.
positive terminal
98.The radiation resistance of a quarterwave antenna is
a. 49 ohms
b. 288 ohms
c. 72 ohms
d. 144 ohms
99.A radio transmission line of 500 ohms impedance is to be connected to an
antenna having an impedance of 200 ohms. What is the impedance of a
quarter wave matching line?
a. 300
b. 316
c. 316.5
d. 361
100.
Which of the following is used to measure SWR?
a. Multimeter
b. reflectometer c. spectrum analyzer
oscilloscope

d.

You might also like