Professional Documents
Culture Documents
EPDM STRIP SEALED TO UPSTAND AND ALUMINIUM FRAME TO INVESTIGATION OF SOLID KICKER TOUGHENED GLAZED UNITS Contract master programme. Pane squareness: Not more than 4 mm difference in diagonal
- Proposals to support outstanding applications for Building Regulation consents or measurements. POWDER COATING APPLICATORS:
FORM WEATHERTIGHT/AIRTIGHT SEAL BELOW EXISTING GLAZING PROVIDE relaxations. Applicator requirements:
SUBJECT TO INTRUSIVE INVESTIGATION OF DISTORTIONAL TOLERANCES ON GLASS: - Approved by powder coating manufacturer.
DOUBLE SKIN SOLID WALL TO NEW STEEL PARAPET HANDRAIL QUALITY PLAN: Measurement of tolerances: After any thermal toughening/ heat - Currently certified to BS EN ISO 9001.
PPC ALUMINIUM DRIP BY WINDOW SUB CONTRACTOR SOLID KICKER BELOW EXISTING GLAZING Requirement: Submit during detailed design. strengthening. - Comply with quality procedures, guarantee conditions, standard
PROVIDE A SILL TO NEW FFL - WALL TO RAISED GUARDING HEIGHT IN ASSUMED SILL WITH Content: In accordance with BS 5750, BS EN ISO 9001 and including the following: Maximum bow: 0.2% of pane dimension. and tests required by powder coating manufacturer.
PROVIDE DOUBLE SKIN SOLID WALL TO
TO SANDWICH OUTER FLANGE OF ACCORDANCE WITH AD PART K BITUMEN COVER TO - Name of the quality manager. Maximum roller wave: - Applicator to use only one plant.
PROVIDE A SILL TO NEW FFL - Quality assessment procedures. - For 3 to 5 mm thick glass: 0.5 mm. - Selected applicator: Submit details before commencement of
COLUMNS SO THAT INNER LEAF BASE OF GLAZING - Inspection procedures to be adopted in checking the work. - For 6 to 10 mm thick glass: 0.3 mm. powder coating including:
VAPOUR BARRIER FULLY ADHERED TO UPSTAND WITH 50mm RUNS INTO COLUMN WEB AND EXISTING PAVERS AND DRAINAGE - Stages at which check lists will be used and samples of the lists. - For 12 mm and thicker glass: 0.15 mm. Name and contact details.
- List of work procedures on the correct use of materials or components, both off Maximum edge dip: Details of accreditation schemes.
THICK KINGSPAN STYROZONE H350 RIGID INSULATION OUTER LEAF RUNS PAST THE RETAINED AND BLAST CLEANED FINISHES IN ACCORDANCE WITH DLA site and on site. - For 3 to 5 mm thick glass: 0.8 mm.
PAVED TERRACE - List of product information with latest revisions. - For 6 to 10 mm thick glass: 0.5 mm. POWDER COATING GUARANTEES:
COLUMN OUTER FACE INTERIORS PROPOSALS WITH DRAIN POINTS - Subcontractors involved in the work. - For 12 mm and thicker glass: 0.25 mm. Powder coating manufacturer and applicator guarantees:
HIGH PERFORMANCE RIGID - Subcontractors' quality plans. - Submit sample copies before commencement of powder coating
HIGH PERFORMANCE SINGLE PLY ROOFING MEMBRANE TO AND GUTTER - Storage, handling, transport and protection procedures. HEAT SOAKED THERMALLY TOUGHENED GLASS: - Submit signed project specific copies on completion of work.
BOARD INSULATION AND ROOFING - Procedure for registering and reporting non compliances. Standard: To BS EN 14179.
UPSTAND AND SEALED TO EXISTING TERRACE ARRANGEMENT
MEMBRANE SEALED TO EXISTING - Maintenance procedures and calibration records. POWDER COATING CONTROL SAMPLES:
WATERPROOFING IN ACCORDANCE WITH MANUFACTURERS SUGGESTING LINEAR - Certification that completed work complies with specification. INSULATING GLASS UNITS: Sequence: Prior to ordering materials for the works, obtain approv
TERRACE WATERPROOFING BUT - Check list register to ensure all items have been inspected and non compliances Standard and labels for hermetically sealed units: To BS EN 1279. of appearance for:
INSTRUCTIONS TOGETHER WITH SACRAFICIAL LAYER WHERE DRAIN CENTRAL TO discharged. Label: Each pane. - Powder coated samples: Of various grades and forms of
SUBJECT TO FURTHER INTRUSIVE SOLID KICKER Perimeter taping: Not to be used. background metal to be used, showing any colour, texture and glo
EXPOSED - ALL SUBJECT TO FURTHER INTRUSIVE TERRACE
INVESTIGATIONS INFORMATION TO BE PROVIDED BEFORE COMMENCEMENT TESTING OR Perimeter seals:
- Resistant to UV light degradation on exposed edges.
variation.
FABRICATION OF CURTAIN WALLING: - Fabrication samples: Showing joint assembly, how powder coat
INVESTIGATIONS BELOW EXISTING GLAZING SYSTEM Submit the following curtain walling particulars: - Compatible with structural, assembly and weather sealants. is affected and how any cut metal edges are finished and protecte
- Detailed drawings to fully describe fabrication and installation. Samples to include the following information:
- Detailed calculations to prove compliance with design/ performance requirements. GLASS EDGE CONDITION FOR STRUCTURAL SEALANT GLAZING: - Product reference.
- Project specific fabrication, handling and installation method statements. Bonded, unframed outer edges: Flat ground with a small arris suitable - Colour.
BLAST CLEANED EXISTING PAVERS AND DRAINAGE RETAINED NEW RAISED FLOOR IN ACCORDANCE - Certification for incorporated components manufactured by others confirming their for open jointing or for weatherseal jointing. - Reference number.
suitability for proposed locations in the curtain walling. - Name.
WITH DLA INTERIORS PROPOSALS - Recommendations for spare parts for future repairs or replacements. INFILL PANELS/ FACINGS: - Gloss level.
Recommendations for safe dismantling and recycling or disposal of products. Tolerances:
- Deviation in size (maximum): 1 mm. QUALITY ASSURANCE SYSTEM:
INFORMATION TO BE PROVIDED BEFORE COMMENCEMENT OF - Deviation in flatness from plane per 2 m length (maximum): 1 mm. Requirement: Powder and coating application to the designated
STRUCTURAL SEALANT GLAZING: Rigidity: Adequate to comply with design/ performance requirements. components is to be tested and approved in accordance with the
Submit structural bonding sealant manufacturer's project specific approval for: Qualicoat system.
- Compatibility and adhesion of products and finishes. GASKETS:
- Full details of structural sealant glazing design. Material: COMPONENT DESIGN:
DETAIL 3 - Structural sealant dimensions. - Noncellular rubber to BS 4255-1. Condition of components to be powder coated:
- Project specific sealant application method statement. - Cellular rubber to ASTM-C509. - To comply with relevant recommendations of BS 4479-1, -3, and
Continuity: Outer gaskets of single front sealed curtain walling systems -4.
NEW RAISED FLOOR IN ACCORDANCE WITH PRODUCT SAMPLES: and inner gaskets of drained and ventilated or pressure equalized curtain - Of suitable size to fit plant capacity.
walling systems must be formed in a complete frame with sealed joints.
DLA INTERIORS PROPOSALS General: Before commencing detailed design, submit labelled samples.
Vulcanized rubber gaskets must have factory moulded corner joints.
- Of suitable thickness to withstand oven curing.
SAMPLES OF FIXINGS: Durability: Resistant to oxidation, ozone and UV degradation. PRETREATMENT OF ALUMINIUM COMPONENTS :
General: During detailed design, submit labelled samples of each type of fixing Condition of components to be pretreated:
EXTERNAL FINISHES TO BE MADE anchor, including casting-in restraints and shims, together with manufacturers' WEATHERSTRIPPING OF OPENING UNITS: - Free from corrosion and damage.
recommended torque figures. Material: - All welding and jointing completed and finish off as specified.
GOOD AS REQUIRED - Noncellular rubber to BS 4255-1. - Free from impurities including soil, grease, oil.
FABRICATION SAMPLES: - Cellular rubber to ASTM-C509. - Suitable for and compatible with the pretreatment process.
General: During detailed design, submit samples of 600 x 600 mm mullion and - Polypropylene woven pile, silicone treated. Conversion coating requirements:
transom intersection with fitted glazing units. Attachment: Fixed in undercut grooves in framing sections using - Chromate system: To BS 6496 or BS EN 12206-1.
INTERNAL FINISHES TO BE MADE GOOD AS - Obtain approval of appearance before proceeding. preformed corners, with any joints in the length. - Chromate-free system: To BS EN 12206-1. Submit details befor
REQUIRED using.
FULL HEIGHT DESIGN/ PERFORMANCE REQUIREMENTS: GENERAL SEALANTS: Rinsing requirements: Use demineralized water. Drain and dry.
FULL HEIGHT THERMALLY BROKEN Selection: In accordance with BS 6213 from:
SINGLE GLAZING CWCT 'STANDARD FOR SYSTEMISED BUILDING ENVELOPES': - Silicone. EXTENT OF POWDER COATINGS:
PPC EXTRUDED ALUMINIUM - One part polysulfide.
IN METAL General: Unless specified or agreed otherwise comply with:
- Two part polysulfide.
Application: To visible component surfaces, and concealed surfac
FRAMING WITH HERMETICALLY Part 2 - Loads, fixings and movement. requiring protection. Coated surfaces will be deemed 'significant
GLAZING BARS Part 3 - Air, water and wind resistance. - One or two part polyurethane. surfaces' for relevant BS 6496 or BS EN 13438 performance
MASTIC SEALANT SEALED GAS FILLED TINTED LOW-E Part 4 - Operable components, additional elements and means of access. Classification and requirements: To BS EN ISO 11600. requirements.
Part 5 - Thermal, moisture and acoustic performance. Reaction to contact products and finishes: Stable and compatible.
TOUGHENED GLAZED UNITS Part 6 - Fire performance APPLICATION OF POWDER COATINGS:
Part 7 - Robustness, durability, tolerances and workmanship. CURTAIN WALLING JOINT ASSEMBLY SEALANTS: Surfaces to receive powder coatings: Free from dust or powder
EPDM STRIP SEALED TO SOFFIT AND ALUMINIUM FRAME TO Project performance requirements specified in this subsection: Read in conjunction Material: One part, low modulus silicone to BS EN ISO 11600, type F or deposits.
with CWCT performance criteria. G. Neutral curing where in contact with or close proximity to other Powder colours: Obtain from one batch of one manufacturer.
FORM WEATHERTIGHT/AIRTIGHT SEAL products that may be adversely affected by acetoxy curing. Commencement of powder coating: To be continuous from
INTEGRITY: pretreatment.
Requirement: The curtain walling must resist wind loads, dead loads and design live WEATHERSEALING FOR STRUCTURAL SEALANT GLAZING: Jig points: Not visible on coated components.
THERMALLY BROKEN PPC EXTRUDED ALUMINIUM FRAMING PE FOAM SHEET AND DOUBLE MASTIC loads, and accommodate deflections and movements without damage. Material: Silicone, one or two part, neutral curing. Designed and Curing: Controlled to attain metal temperatures and hold periods
WITH HERMETICALLY SEALED GAS FILLED TINTED LOW-E SEAL BY WINDOW SUB CONTRACTOR Design wind pressure: Calculate in accordance with BS 6399-2. manufactured for weathersealing of structural sealant glazing. recommended by powder coating manufacturer.
Compatible with contact and close proximity products and finishes. Stripping and recoating of components: Only acceptable by prior
TOUGHENED GLAZED UNITS TO WINDOW SUB CONTRACTORS DEFLECTION UNDER DEAD LOADS: agreement of powder coating manufacturer. Stripping, pretreatme
Requirement: Framing members parallel to the curtain walling plane must not: THERMAL INSULATION: and powder coating are to be in accordance with manufacturer's
SPECIFICATION AND DETAILS - Reduce glass bite to less than 75% of design dimension. - Properties: Durable, rot and vermin proof and not degradable by requirements.
- Reduce edge clearance to less than 3 mm between members and immediately moisture or water vapour. Overcoating of components: Not acceptable.
adjacent glazing units, panel/ facing units or other fixed units. Fixing: Attached to or supported within the curtain walling so as not to
- Reduce clearance to less than 2 mm between members and movable bulge, sag, delaminate or detach during installation or in situ during the PERFORMANCE AND APPEARANCE OF POWDER COATINGS
components such as doors and windows. life of the curtain walling. For aluminium components:
- Standard: To BS 6496 or BS EN 12206-1.
DEFLECTION UNDER WIND LOAD: FINISHES: Visual inspection after powder coating: Significant surface viewing
EXISTING HANDRAILS TO BE Requirement: To CWCT 'Standard for systemised building envelopes' clause 3.5 2. distances to be as specified in the relevant Standard, unless
EXTERNAL FINISHES TO BE MADE GOOD AS REQUIRED DETAIL 4 RETAINED AND TO RECEIVE A PROTECTIVE COATING OF CARBON STEEL FRAMING SECTIONS/ specified otherwise.
GENERAL MOVEMENT: REINFORCEMENT: Colour and gloss levels: To conform with approved samples.
HIGH BUILD PAINTED FINISH Requirement: Curtain walling must accommodate anticipated building movements. Treatment: One of the following to all surfaces:
- Hot dip galvanized to BS EN ISO 1461. ALUMINIUM ALLOY FABRICATIONS:
THERMALLY BROKEN PPC EXTRUDED ALUMINIUM FRAMING APPEARANCE AND FIT: - An appropriate equivalent coating to BS 5493, BS EN ISO 12944 or Units may be assembled:
WITH HERMETICALLY SEALED GAS FILLED TINTED LOW-E Requirement: Design curtain walling system: BS EN ISO 14713. - Before powder coating.
- To ensure position and alignment of all parts and features as shown on - From components powder coated after cutting to size.
TOUGHENED GLAZED UNITS TO WINDOW SUB CONTRACTORS preliminary design drawings. PROTECTIVE COATING OF CARBON STEEL MECHANICAL FIXINGS: - Where approved, from components powder coated before cuttin
- To accommodate deviations in the primary support structure. Treatment: One of the following to all surfaces: to size.
SPECIFICATION AND DETAILS Primary support structure: Before commencing installation of curtain walling system, - Hot dip galvanized to BS EN ISO 1461. Exposure of uncoated background metal: Not acceptable.
carry out survey sufficient to verify that required accuracy of erection can be - Sherardized to BS 4921, class 1 coating thickness and passivated. Assembly sealants: Compatible with powder coatings. Obtain
PE FOAM SHEET AND DOUBLE MASTIC SEAL BY WINDOW SUB FULL HEIGHT achieved. - Zinc plated to BS EN 12329, coating designation Fe//Zn//C for an
iridescent (yellow passivate) chromate conversion coating or Fe//Zn//D
approval of colour if sealants are visible after fabrication.
- Give notice: If the structure will not allow the required accuracy or security of
CONTRACTOR SINGLE GLAZING erection. for an opaque (olive green) chromate conversion coating. FIXINGS:
RAKED THERMALLY BROKEN PPC Exposed metal fixings: Powder coat together with components, or
IN METAL THERMAL MOVEMENT - SERVICE TEMPERATURE RANGES: FABRICATION AND INSTALLATION: coat with matching repair paint system applied in accordance with
FINISHES IN ACCORDANCE WITH EXTRUDED ALUMINIUM FRAMING
GLAZING BARS Requirement: To CWCT 'Standard for systemised building envelopes' clause 2.7.2. the powder coating manufacturers recommendations.
DLA INTERIORS PROPOSALS WITH HERMETICALLY SEALED GAS GENERALLY:
AIR PERMEABILITY: Electrolytic corrosion: Prevent. Submit proposed methods. DAMAGED COMPONENTS - REPAIR/ REPLACEMENT:
CONTINUOUS PPC INSULATED ALUMINIUM PANEL WEATHER FILLED TINTED LOW-E TOUGHENED Requirement: Permissible air leakage rates of 1.5m/hr/m for fixed lights and 2.0 Fixings: Concealed unless indicated on detailed drawings. Where Before delivery to site: Check all components for damage to powd
EXISTING METAL m/hr/lin.m for opening lights must not be exceeded when the curtain walling is exposed they must match material and finish of the products fixed. coatings. Replace damaged components.
AND AIR SEALED INTO FRAME TO WINDOW SUB CONTRACTORS GLAZED UNITS FIXED TO EXISTING Fabrication: Machine cut and drill products in the workshop wherever Site damage: Submit proposals for repair or replacement.
BALUSTRADE subjected to the peak test pressure.
SPECIFICATION AND DETAILS STRUCTURE possible.
WATER PENETRATION: Identification of products: Mark or tag to facilitate identification during PROTECTION:
Watertightness class to BS EN 12154. assembly, handling, storage and installation. Do not mark surfaces Powder coated surfaces of components: Protect from damage
visible in the completed installation. during handling and installation, or by subsequent site operations.
THERMAL PROPERTIES: Protective coverings: Must be:
THERMALLY BROKEN PPC EXTRUDED ALUMINIUM FRAMING Method of calculating the thermal transmittance (U-value) of curtain walling/ each ASSEMBLY: - Resistant to weather conditions.
General: Carry out as much assembly as possible in the workshop. - Partially removable to suit building in and access to fixing points
WITH HERMETICALLY SEALED GAS FILLED TINTED LOW-E zone of curtain walling: Weighted U-value.
Average U-value of curtain walling: 2.0W/mK. Joints (other than movement joints): Rigidly secured, reinforced where Protective tapes in contact with powder coatings: Must be:
TOUGHENED GLAZED UNITS FIXED TO EXISTING STRUCTURE Curtain wall zone interfaces: Co-ordinate to achieve required average U-value. necessary and fixed with hairline abutments. - Low tack, self adhesive and light in colour.
Method for assessing thermal transmittance (U-value) of assemblies. Displacement of components in assembled units: Submit proposals for - Applied and removed in accordance with tape and powder coati
TO WINDOW SUB CONTRACTORS SPECIFICATION AND DETAILS reassembly on site. manufacturers' recommendations. Do not use solvents to remove
THERMAL STRESS IN GLAZING: residues as these are detrimental to the coating.
DETAIL 4 Glass panes/ units: Must have adequate resistance to thermal stress generated by FIXING ANCHOR INSTALLATION: Inspection of protection: Carry out monthly. Promptly repair any
orientation, shading, solar control and construction. Site drilling or cutting into structure: Submit proposals for positions other deterioration or deficiency.
than shown on detailed drawings.
AVOIDANCE OF CONDENSATION: Concrete supporting structure: DOCUMENTATION:
Requirement: Notional psychrometric conditions under which condensation must not - Cast-in inserts: Provide detailed locational information. Protect cavities Submit the following information for each batch of powder coated
form on building interior surfaces of framing members or any part of infill panels/ in inserts from entry of concrete. components:
facings are: - Edge fixing distances: Not less than recommended by fixing anchor - Supplier.
INTERNAL FINISHES TO BE MADE GOOD AS - Notional outdoor psychrometric conditions as BS 6229, table A1. manufacturers. - Trade name.
REQUIRED - Notional indoor psychrometric conditions: Corrective fabrication: Minimize. Where necessary, submit proposals. - Colour.
- Type of powder.
SOUND TRANSMITTANCE: PRELIMINARY CURTAIN WALLING INSTALLATION: - Method of application.
Minimum weighted sound reduction index (Rw) to BS EN ISO 717-1. Requirement: Complete an area for inspection and approval of - Batch and reference number.
Minimum weighted standardized level difference (DnTw) to BS EN ISO 717-1. appearance. - Statutory requirements.
- Test certificates.
FIRE RESISTANCE OF CURTAIN WALLING: CURTAIN WALLING INSTALLATION: - Maintenance instructions.
Standard: To BS 476-22. Securing to fixing anchors: Through holes formed during fabrication only.
Tightening mechanical fasteners: To manufacturer's recommended COMPLETION:
INTERNAL SURFACE SPREAD OF FLAME OF CURTAIN WALLING: torque figures. Do not overtighten fasteners intended to permit Protection: Remove.
Standard: To BS 476-7. differential movement. Cleaning and maintenance of powder coatings: Carry out in
Protective coverings: Remove only where necessary to facilitate accordance with procedures detailed in powder coating
installation and from surfaces that will be inaccessible on completion. manufacturer and applicator guarantees.
INTERNAL FINISHES TO BE MADE GOOD AS REQUIRED FIRE STOPPING:
Locations: At junctions of curtain walling with compartment walls and floors.
DETAIL 5 Materials and methods of fixing: To ensure fire resistance not less than that
specified for compartment walls and floors.
For Planning
DOORS AND OTHER ACCESS FACILITIES:
Access facilities designated for use by disabled persons.
Strength and durability: To CWCT 'Standard for systemised building envelopes'
clause 4.3.3.
DURABILITY:
Relevant agents or degradation mechanisms.
DLA ARCHITECTURE
Design life of the curtain walling system.
Secondary components: Submit details together with required maintenance regime,
replacement periods and methods of replacement.
2009-075/203 B
ADHESIVES:
General: Not degradable by moisture or water vapour.
FIXING ANCHORS:
Type and use: Reviewed and approved by fixing manufacturers. Submit
confirmatory information on request. DWG PATH
Dimensions: Not less than recommended by their manufacturers.
TYPICAL SECTION - PROPOSED - 1:20 TYPICAL SECTION - EXISTING - 1:20 Adjustment capability: Sufficient in three dimensions to accommodate building T:\2009\2009-075\CAD\05-Autocad\Dwgs\SU GLAZING\203
ORIGINAL PAPER SIZE A1
structure and curtain walling fabrication/ installation tolerances.