Professional Documents
Culture Documents
NEN-EN 558-1
Industrile afsluiters. Inbouwmaten
voor metalen afsluiters voor gebruik in
pijpleidingsystemen met flensverbindingen.
Deel 1 : Afsluiters met PN-aanduiding
Dit document bevat de geratificeerde Engelse versie van de Europese norm EN 558-1, oktober 1995.
Dit document mag slechts op een stand-alone PC worden geinstalleerd. Gebruik op een netwerk is alleen.
Toelichting
Ten behoeve van de openbaarheid van normen is besloten deze geratificeerde versie ter beschikking te stellen.
a supplementary license agreement for us in a network with NEN has been concluded.
Zodra de officile Engelse versie beschikbaar is, zal deze de geratificeerde versie vervangen en met een nieuw
voorblad als nieuwe druk worden uitgegeven.
Pr
ev
be
iew
eld
Behoudens uitzondering door de wet gesteld mag Hoewel bij deze uitgave de uiterste zorg is nagestreefd,
zonder schriftelijke toestemming van het Neder- kunnen fouten en onvolledigheden niet geheel worden
lands Normalisatie-instituut niets uit deze uitgave uitgesloten. Het Nederlands Normalisatie-instituut en/of
worden verveelvoudigd en/of openbaar gemaakt door de leden van de commissies aanvaarden derhalve geen
middel van fotokopie, microfilm, opslag in computer- enkele aansprakelijkheid, ook niet voor directe of indi-
bestanden of anderszins, hetgeen ook van toepassing is recte schade, ontstaan door of verband houdende met
op gehele of gedeeltelijke bewerking. toepassing van door het Nederlands Normalisatie-insti-
tuut gepubliceerde uitgaven.
Het Nederlands Normalisatie-instituut is met uitsluiting
van ieder ander gerechtigd de door derden verschuldig-
de vergoedingen voor verveelvoudiging te innen en/of
daartoe in en buiten rechte op te treden, voor zover deze
bevoegdheid niet is overgedragen c.q. rechtens toekomt Prijsklasse 30
aan de Stichting Reprorecht.
N Normalisatie-instituut
Nederlands 1995 Nederlands Normalisatie-instituut
Kalfjeslaan 2, Postbus 5059, 2600 G Delft, Telefoon (015) 2 690 390, Fax (015) 2 690 190
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Nederlands v o o r w o o r d
Voor de in deze norm vermelde andere normen bestaan in Nederland de volgende equivalenten:
eld
Dit document is een voorbeeld van NEN / This document is a preview by NEN
EUROPEAN STANDARD EN 558-1
NORME EUROPEENNE
ICS 23.060.00
Descriptors: industrial valves, valves-and fittings, cocks, flanged valves, metallurgical products, dimensions, generalities
English version
Vo
Industrial valves - Face-to-face and centre-to-face
dimensions of metal valves for use in flanged pipe
systems - Part 1 : PN-designated valves
or
Robinetterie industrielle - Dimensions Industriearmaturen - Baulngen von Armaturen
face--face et face--axe de la robinetterie aus Metall zum Einbau in Rohrleitungen mit
mtallique utilise dans les systmes de Flanschen - Teil 1: Nach PN bezeichnete
canalisations brides - Partie 1: Appareils de Armaturen
robinetterie dsigns PN
Pr
ev
be
iew
This European Standard was approved by CEN on 1995-10-16. CEN members are bound to comply with the CEN/CENELEC Internal
Regulations which stipulate the conditions for giving this European Standard the status of a national standard without
any alteration.
eld
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to
the Central Secretariat or to any CEN member.
The European Standards exist in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Central
Secretariat has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland,
Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.
CEN
European Committee for Standardization
Comit Europen de Normalisation
Europisches Komitee fr Normung
1995 All rights of reproduction and communication in any form and by any means
reserved in all countries to CEN and its members.
Ref. No. EN 558-1:1995 E
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 2
EN 558-1:1995
Contents Page
Foreword 3
0 Introduction 4
1 Scope 5
Vo
2 Normative references 5
3 Definitions 5
Annex
or
A (informative) Origin of basic series 25
Tables
2 Tolerances 10
be
3 Gate valves 11
ev
Figures
1 6
2 6
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 3
EN 5 5 8 - 1 : 1 9 9 5
Foreword
This European Standard has been prepared by the Technical Committee CEN/TC
69 "Industrial valves" of which the secretariat is held by AFNOR.
This European Standard shall be given the status of a national standard, either
by publication of an identical text or by endorsement, at the latest by April
1996, and conflicting national standards shall be withdrawn at the latest by
April 1996.
Vo
This European Standard has been prepared under a mandate given to CEN by
the European Commission and the European Free Trade Association, and
supports essential requirements of EC Directive(s).
This standard was drawn up on the basis of the international draft standard
ISO/DIS 5752 and contains two Parts which can be used separately:
The progress in work in the standardization of the different products can require a revision
Pr
bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France,
Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal,
Spain, Sweden, Switzerland and United Kingdom.
eld
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 4
EN 558-1:1995
0 Introduction
All tables of face-to-face and centre-to-face dimensions are drafted separately for PN
designated valves in EN 558-1 and for Class designated valves in EN 558-2.
The basic series in this standard are taken from the origin series shown in annex A
(informative). Changes made to the origin series will not be automatically incorporated into
this standard.
Vo
The numbers of the basic series are maintained as in ISO/DIS 5752: 1993.
or Pr
ev
be
iew
eld
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 5
EN 558-1:1995
1 Scope
This part of this standard specifies face-to-face (t it) and centre-to-face (CTF) dimensions
for PN designated metal valves used in flanged pipe systems.
This part of this standard covers valves having the following PN and DN values:
Vo
- PN 2,5; PN 6; PN 10; PN 16; PN 25; PN 40; PN 63; PN 100.
- D N 10; D N 15; D N 20; D N 25; D N 32; D N 40; D N 50; D N 65; D N 80; D N 100;
D N 125; D N 150; D N 200; D N 250; D N 300; D N 350; D N 400; D N 450; D N 500;
D N 600; D N 700; D N 800; D N 900; D N 1 000; D N 1 200; D N 1 400; D N 1 600; D N
1 800; D N 2 000.
This standard incorporates, by dated or undated reference, provisions from other publications.
These normative references are cited at the appropriate places in the text and the publications
Pr
are listed hereafter. For dated references, subsequent amendments to or revisions of the cited
be
publication dpply to this European Standard, only when incorporated in it by amendment or
ev
revision. For undated references, the latest edition of the publication referred to applies.
iew
3 Dfinitions
For the purposes of this standard, prEN 736-1 and the following definitions apply:
3.1 face-to-face dimension (FEF) (for straight pattern valves): The distance, expressed in
millimetres, between the two planes perpendicular to the valve axis located at the extremities
of the body end ports or as may be specified in the relevant valve product standard (see
figures 1 and 2).
3.2 centre-to-face dimension (CTF) (for angle pattern valves): Tbe distance, expressed in
millimetres, between the plane located at the extremity of either body end port and
perpendicular to its axis and the axis of the other body end port (see figures 1 and 2).
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 6
EN 5 5 8 - 1 : 1 9 9 5
Vo
I
I
FTF
CTF
or
Figurel
Pr
ev
be
iew
M i i
I
eld
FTF/CTF. FTF/CTF. FTF/CTF FTF/CTF FTF/CTF FTF/CTF,
Figure 2
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Page 7
EN 558-1:1995
The basic series of FTF and CTF dimensions shall be as given in table 1.
For each type of valve, the basic series to be taken into consideration are given in tables 3
to 17.
Vo
4.2 Dimensions for unlined valves
For unlined valves the FTF and CTF dimensions shall be in accordance with figures 1
and 2.
4.3.1 For valves having a resilient lining which forms the gasket joint with the mating
or
flanges, the FTF and CTF dimensions shall be the distance between the extremities of the
valve in the installed condition.
The overall valve dimensions before assembly shall be provided by the manufacturer.
Pr
4.3.2 For valves having resilient or hard linings as a regular production feature the
be
thickness of the lining on the mating surface shall be included in the FTF and CTF
ev
dimensions given in table 1, unless the design of the valve precludes such an inclusion.
iew
Where the design does not permit the lining to be included in the FTF and CTF
dimensions given in table 1, then the thickness of the lining may be added to the basic
dimension.
4.3.3 For valves having resilient or hard linings which are not normally a regular
eld
production feature, the thickness of the lining on the flange faces may be added to the FTF
and CTF dimensions given in table 1.
4.4 Tolerances
Dit document is een voorbeeld van NEN / This document is a preview by NEN
Bestelformulier
Stuur naar:
NEN Standards Products & Services NEN Standards Products & Services
t.a.v. afdeling Klantenservice Postbus 5059
Antwoordnummer 10214 2600 GB Delft
2600 WB Delft Vlinderweg 6
2623 AX Delft