Professional Documents
Culture Documents
Caution To avoid fire or electric shock, please comply with the basic safety
Notice please close the screen and computer power to prevent the product
Thank you for buying our LED display products, please read and understand the LED
display using manualBefore installation and use.
LED display is easy to install, we can complete the installation settings in accordance
with the manual without professional personnel. Before you install and use this product,
please read carefully all operation process of this product (The purpose of this manual
is to help you know and use the LED display correctly)
4Using process
4.1 The installation conditions
1 The Indoor led screen adopts vacuum package except sheet metal box. It
should be properly mounted in environment with no rain damage, Strong Acids,
Corrosive Gas, and avoid strong mechanical shock or magnetism.
When turn on the screen for the firstly time after installation, the RGB gray scale
must be set to 80, and aging for 8 hours, then it can be used normally. The
indoor screen can not be turned off more than 24 hours, for its long-time using
sake. If it has been turned off for 1-3 days during to some reasons, when
restart, the gray scale must be set to 80, full white and aging for 4 hours, then
change to normal brightness to use.
If the screen is turned off more than 3 days, when restart it, the gray scale must
be set to 80, full white aging for 4 hours, after that set it to 130, full white aging
for 4 hours, then turn to 200 full white aging for 4 hours, finally turn to normal
brightness to use.
For more details, please refer to The Display preheat aging Manual. When
long time no use, the indoor rental screen must be stored at dry environment,
environmental temperature is -40t80, Humidity: 65 . If the
temperature and humidity exceeds the above range, please use air conditioner
for cooling and dehumidification.
2The Outdoor led screen can be installed directly in outdoor environment with no
Strong Acids, Corrosive Gas, and avoid strong mechanical shock or magnetism.
When turn on the screen for the firstly time after installation, the gray scale must
be set to 80, full white and aging for 4 hours, then change to normal brightness
LED display user manual
to use.
If it has been turned off more than 1 month, when restart, the gray scale must
be set to 80, full white and aging for 4 hours, then change to 200 full white aging
for 4 hours, finally turn to normal brightness to use.
For more details, please refer to The Display preheat aging Manual. When
long time no use, the outdoor rental screen must be stored at dry environment,
environmental temperature is -40t80, Humidity: 65 . If the
temperature and humidity exceeds the above range, please use air conditioner
for cooling and dehumidification.
3 Mesh screen must be installed in the place without rain & water splashed,
strong acid & corrosive gas, and mechanical shock or strong magnet must be
avoided around the mesh screen.
4 If the renal mesh screen is exposed to the rain, it must be dried before being
packed, and the storage environment of rental mesh screen must be dry and
ventilated and it needs lighting up to test every once in a while.
installation is ready), Please operate with tips: First install DirectX8.1; And then
install the driver; And finally install control panel.
2: play software: Install the dedicated broadcast and set software for big screen - Led
studio, or other control software, put the CD of the screen into CD-Rom, copy or
download all procedure to computer.
5. LED Display Operating Steps
5.1 Turn on Screen: Please Turn on the computer first, when the computer is running
well, then turn on the screen power after entering the engineering control software.
When you open the LED screen, there will be a regional flicker on screen, which
indicates Screen is powered, turn on the computer (please make sure the graphics
card settings is correct ,because incorrect setting will cause no picture on the
screen, which means screen is black), open the control software, set the basic
pixel size and display area (this setting does not affect the picture on LED
screen).
5.2 Turn off-screen: First turn off the power of LED screen, then turn off the control
software, finally turn off the computer in the right way.
(If the computer is turned off before than screen, it may cause the screen with
high bright dot and lamps burned when there is no signal)
5.3 Note: Interval of Switching screen should be greater than 5 minutes.
6. LED Screen unit package packing list:
LED cabinet; signal cable; power cable; sending cards (if there is computer, the
sending card should be installed in the computer); receiving card (installed in the LED
cabinets); desktop (graphics card with DVI output and serial port); display and related
accessories
7, System settings: (refer to Linsn system manual)
8 common malfunction and solution.
8.1 When the LED studio is started, why does it show could not find the controlling
system or communication error?
It is because that serial communication cables is not connected well with sending card
or communication cables is not connected well. Please check the communication
cables is well connected with serial port, and restart LED studio after connection.
LED display user manual