Professional Documents
Culture Documents
Q.1) An indirect waste line must be trapped when it exceeds how many feet in developed length?
A. 2'
B. 3'
C. 4'
D. 5'
Q.2) T&P Valves must have a temperature rating of?
A. 190F
B. 200F
C. 210F
D. 220F
Q.3) Which of these Trap designs are prohibited?
A. S-Trap
B. Bell Trap
C. Drum Trap
D. All 3 of them
Q.4) Horizontal PVC Pipe must be supported every?
A. 4'
B. 5'
C. 8'
D. 10' (Your Answer)
Q.5) A vent connecting at the junction of two fixture drains and serving as the vent for both is called?
A. Wet Vent
B. Twin Vent
C. Branch Vent
D. Common Vent
Q.6) A drain pan terminating outside must be a minimum of how many inches above grade?
A. 4"
B. 6"
C. 8"
D. 10"
Q.7) What is the minimum distance from a side wall to a handicap water closet?
A. 10-12"
B. 13-15"
C. 16-18"
D. 19-21"
Q.8) What is the minimum size water service in Onondaga County?
A. 1/2"
B. 3/4"
C. 1"
D. 3/8"
Q.9) What is the maximum temperature of water that can discharge into the sanitary drainage system?
A. 110F
B. 120F
C. 130F
D. 140F
Q.10) An indirect drain that discharges above the flood level rim is called an?
A. Air Gap
B. Air Break
C. Air Space
D. Air Allowance Separation (AAS)
Q.11) Horizontal Cast Iron Pipe must be supported every?
A. 5'
B. 6'
C. 10'
D. 12'
Q.12) What is the weight of 1 cubic foot of water?
A. 40 pounds
B. 52.5 pounds
C. 57 pounds
D. 62.5 pounds
Q.13) What is the minimum slope for a 3" drain pipe?
A. 1/16"
B. 1/8"
C. 1/4"
D. 3/8"
Q.14) A water service must be at least how far below grade?
A. 6"
B. 12"
C. 18"
D. 24"
Q.1) When are hot and cold shower valves identical?
A. Always
B. Never
C. Sometimes
D. Not Sure
Q.2) When can a diverter valve replace a hot or cold shower valve?
A. Always
B. Never
C. Sometimes
D. Not Sure
Q.3) Stem packing is used when leaking occurs at which location?
A. Tub Spout
B. Shower valve
C. Drain
D. Shower Head
Q.4) Where is the cold water valve located?
A. Left Side
B. Right Side
C. Center
D. Bottom
Q.5) What do all toilets have built into them?
A. Anti-Syphon Valve
B. P-Trap
C. T P valve
D. Shut-Off valve
Q.6) What can never be re-used when replacing a toilet?
A. Flange Bolts
B. Wax Ring
C. Plastic Shims
D. Closet Flange
Q.7) How many p-traps does a double kitchen sink require?
A. One
B. Two
C. Three
D. Four
Q.8) What fits between a closet flange and toilet bowl?
A. Spud washer
B. Wax Ring
C. O-Ring
D. Lock Washer
Q.9) What connects a P-Trap to the drain?
A. Coupling
B. Elbow
C. Trap Adaptor
D. Union
Q.10) Where can the size of a P-Trap be changed?
A. J-Bend
B. Wall
C. Both the J-bend and the wall
D. neither the j-bend or the wall
Q.11) The tail piece on a lavatory is what diameter?
A. 1 1/2"
B. 1 1/4"
C. 2 1/2"
D. 2 1/4"
Q.12) The tail piece on a kitchen sink is what diameter?
A. 1 1/2"
B. 1 1/4"
C. 2 1/2"
D. 2 1/4"
Q.13) What color of flame is best for soldering?
A. Red
B. Yellow
C. Blue
D. Orange
Q.14) What must be applied to a copper fitting and copper pipe before soldering?
A. Water
B. Oil
C. Flux
D. Glue
Q.15) What substance is not permitted in solder which is used for water supply pipes?
A. Tin
B. Brass
C. Lead
D. Steel
Q.16) What is the slope most often required for drainage?
A. Elmers Glue
B. Silicone
C. Solvent Glue
D. JB Weld
Q.18) PSI is the abbreviation for what?
A. Pressure Side In
B. Pounds per Square Inch
C. Plumbing Safety Inquiry
D. Pounds per Square Foot
Q.19) The anode rod on a water heater is made of what material?
A. Copper
B. Magnesium
C. Galvanized Pipe
D. Plastic
Q.20) The safety valve on a water heater is called what?
A. Anti-Syphon valve
B. Shut-off Valve
C. Drain Valve
D. TP valve
Q.21) The drain valve on a water heater has what kind of thread?
A. 120 volts
B. 240 volts
C. 360 volts
D. 115 volts
Q.23) How many thermostats does an electric water heater have?
A. One
B. Two
C. Three
D. None
Q.24) The water supply pipe that enters and leaves a water heater is what size?
A. 1/4"
B. 1/2"
C. 3/4"
D. 1"
Q.25) What is used to unclog a toilet?
A. BLOW ON
B. BLOW OFF (Correct Answer)
C. HOT VALVE
D. PRESSURE VALVE (Your Answer)
Q.2) TRAP SEALS FOR WATER CLOSETS
A. 1 1/4"
B. 1 1/2"
C. 3" (Your Answer)
D. 2"
Q.3) TRAP SEALS FOR WASH BASIN LAVATORIES
A. 1 1/4"
(Correct Answer)
B. 1 1/2"
C. 3"
D. 2" (Your Answer)
Q.4) TRAP SEALS FOR URINAL THROUGH
A. 1 1/2"
B. 1 1/4"
C. 3"
D. 2" (Your Answer)
Q.6) TRAP SEALS FOR URINAL PEDESTAL
A. 1 1/2"
B. 1 1/4"
C. 3" (Correct Answer)
D. 2" (Your Answer)
Q.7) TRAP SEALS FOR URINAL LIP
A. 1 1/2"
B. 1 1/4"
C. 3"
D. 2" (Your Answer)
Q.9) TRAP SEALS FOR SLOPS SINKS (COMBINE TRAP)
A. 1 1/2"
B. 1 1/4"
C. 3" (Your Answer)
D. 2"
Q.10) TRAP SEALS FOR SINKS (SMALL PANTRY OR BAR)
A. 1 1/2"
B. 1 1/4" (Your Answer)
C. 3"
D. 2"
Q.11) TRAP SEALS FOR SINKS (KITCHEN or RESIDENCE)
A. 1 1/2"
(Your Answer)
B. 1 1/4"
C. 3"
D. 2"
Q.12) TRAP SEALS FOR SINKS (hotel or public)
A. 1 1/2"
B. 1 1/4"
C. 3"
D. 2" (Your Answer)
Q.13) TRAP SEALS FOR SINKS (DISH WASHER)
A. 1 1/2"
B. 1 1/4"
C. 3"
D. 2" (Your Answer)
Q.15) TRAP SEAL FOR BIDET
A. 1 1/2"
B. 1 1/4" (Your Answer)
C. 3"
D. 2"
Q.19) TRAP SEAL FOR FOOT BATH SITZ
A. 1 1/2"
(Your Answer)
B. 1 1/4"
C. 3"
D. 2" (Correct Answer)
Q.21) TRAP SEAL FOR FOOT BATH
A. 1 1/2"
(Your Answer)
B. 1 1/4"
C. 3"
D. 2"
Q.22) TRAP SEAL FOR DRINKING FOUNTAIN
A. 1 1/2"
B. 1 1/4" (Your Answer)
C. 3"
D. 2"
Q.23) TRAP SEAL FOR COMBINATION FIXTURE
A. JOINT
B. ANGLE JOINT
C. BALL JOINT (Your Answer)
D. COCK JOINT
Q.28) faucet opened and closed by a ball floating on the water, also called ball cock valve.
A. RISER
B. STACK (Your Answer)
C. BRANCH
D. SERVICE PIPE
Q.32) a tool used for straightening or expanding lead pipe.
A. BATTERY
B. BRANCH
C. BRANCH INTERVAL (Your Answer)
D. NON OF THE ABOVE
Q.34) .), a plumbing fixture use to wash the genitals, also called a sitz bath (tool bath
A. AT THE GATE
B. UNDER THE SIDE WALK ON NARROW ROAD AND UNDER THE ROAD ON WIDE ROAD
C. AT THE CENTER OF THE ROAD
D. NEAR THE CURB
Q.37) TEFLON, A WHITE, SOFT, WAXY, AND NON ADHESIVE POLYMER IS USED AS A LEAK
PREVENTION MATERIAL FOR PIPES PARTICULARLY GALVANIZED IRON PIPES. IT IS P
LACED BETWEEN THE THREADED PIPE END AND FITTING, WHAT IS THE CHEMICAL NAME
OF TEFLON?
A. TRIFLOURORTHANE
B. POLYETHYLENE
C. TETRAFLOUROETHYLENE (Your Answer)
D. PENTAFLOUROCARBON
Q.38) AN ENGINEERED MATERAIL CREATED THROUGH A PATENTED PROCEDURE THAT BONDS
GLOSSY PORCELAIN ENAMELED METAL TO A STRUCTURAL COMPOSITE THROUGH AN
NJECTION MOULDING PROCESS, USED PARTICULARLY IN MANUFACTURING BATHUBS.
WHAT IS THE PATENTED MATERIAL USED IN THE MARKET TODAY?
A. XPELOR
B. DACRON
C. LUCITE (Your Answer)
D. AMERCAST (Correct Answer)
Q.39) IN A TYPICAL GREASE TRAP, WHAT SHOULD BE THE CORRECT ARRANGEMENT OF ITS
INLET AND OUTLET IN ITS ELEVATION
A. A VENT IS NECESSARY
B. INLET PIPE CONNECTED AT THE LEACHING CHAMBER
C. NO AIR SPACE BETWEEN UNDERSIDE OF SLAB AND SCUM LINE (Your Answer)
D. ALL OF THESE (Correct Answer)