Professional Documents
Culture Documents
6
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
Specifier's comments:
1. Input data
Anchor type and diameter: HIT-RE 500 + Rebar, 16mm
Dynamic set or any suitable annular gap filling solution
Effective embedment depth: h ef,opti = 203 mm (hef,limit = 320 mm)
Material: BSt 500 S
Evaluation Service Report: ETA 04/0027
Issued I Valid: 6/26/2013 | 5/16/2018
Proof: design method SOFA design method + fib (07/2011) - after ETAG BOND testing
Stand-off installation: e b = 0 mm (no stand-off); t = 13 mm
Anchor plate: lx x l y x t = 300 x 300 x 13 mm (Recommended plate thickness: not calculated)
Profile no profile
Base material: uncracked concrete , C25/30, fc = 25.00 N/mm; h = 500 mm, Temp. short/long: 40/24C
Installation: hammer drilled hole, installation condition: dry
Reinforcement: no reinforcement or reinforcement spacing >= 150 mm (any ) or >= 100 mm ( <= 10 mm)
no longitudinal edge reinforcement
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu PROFIS Anchor 2.4.6
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
Steel Strength
NRk,s [kN] g M,s NRd,s [kN] NSd [kN]
111.000 1.400 79.286 58.779
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu PROFIS Anchor 2.4.6
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu PROFIS Anchor 2.4.6
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
5. Combined tension and shear loads SOFA (fib (07/2011), section 16.2.3)
bN bV a Utilization bN,V [%] Status
steel 0.741 0.159 2.0 57 OK
concrete 0.986 0.075 1.5 100 OK
a a
bN + bV <= 1
6. Displacements
The displacement of the highest loaded anchor should be calculated according to the relevant approval under the effect of the following
characteristic loads.
NSk = 43.540 [kN]
VSk = 5.730 [kN]
The acceptable anchor displacements depend on the fastened construction and must be defined by the designer!
7. Warnings
The design method fib (07/2011) assumes that no hole clearance between the anchors and the fixture is present. This can be achieved by
filling the gap with mortar of sufficient sompressive strength (e.g. by using the Hilti Dynamic Set) or by other suitable means.
The compliance with current standards (e.g. EC3) is the responsibility of the user
Characteristic bond resistances depend on short- and long-term temperatures.
Checking the transfer of loads into the base material is required in accordance with fib (07/2011)!
To avoid failure of the anchor plate the required thickness can be calculated in PROFIS Anchor. Load re-distributions on the anchors due to
elastic deformations of the anchor plate are not considered. The anchor plate is assumed to be sufficiently stiff, in order not to be deformed
when subjected to the loading!
The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to be
followed to ensure a proper installation.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu PROFIS Anchor 2.4.6
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu PROFIS Anchor 2.4.6
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
8. Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-RE 500 + Rebar, 16mm
Profile: no profile Installation torque: 0.000 kNm
Hole diameter in the fixture: df = 16 mm Hole diameter in the base material: 20 mm
Plate thickness (input): 13 mm Hole depth in the base material: 203 mm
Recommended plate thickness: not calculated Minimum thickness of the base material: 243 mm
Cleaning: Manual cleaning of the drilled hole according to instructions for use is required.
Annular gap must be removed by e.g. filling the holes with mortar of sufficient compressive strength.
60.0
150.0
3 4
x
150.0
1 2
60.0
60.0 60.0
150.0 150.0
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.lu PROFIS Anchor 2.4.6
Company: Page: 7
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: -|- Date: 1/30/2017
E-Mail:
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan