Professional Documents
Culture Documents
!
N
O
TI
LU
O
ES
R
W
LO
AMIANTIT
A winning combination
!
N
O
Production Process
TI
LU
O
Exterior Surface
Core
Interior Liner
!
bending, long term pressure and strain corrosion
N
capability. FLOWTITE pipes and coupling systems have
been rigorously tested to verify conformance to those
O
standards. In the meantime, extrapolation even up to 150
years could be achieved and FLOWTITE GRP pipes meet
TIherewith the requirements of some institutions
requesting a pipe life cycle of more than 100 years.
LU
Product Benefits
O
ES
Corrosion Resistant
protection
Low maintenance costs
Hydraulic characteristics essentially constant over time
LO
Long Standard Lengths (6, 12 and 18 meters) Precision FLOWTITE Coupling with Elastomeric Gaskets
Fewer joints reduces installation time Tight, efficient joints designed to eliminate infiltration
More pipes per truckload means lower delivered cost or exfiltration
Ease of joining, reduces installation time
Accommodates small changes in line direction or
Superior Hydraulic Characteristics differential settlements without additional fittings
GRP pipes from FLOWTITE are used in numerous FLOWTITE pipe systems are supplied in nominal
applications including: diameters ranging from DN 100 up to DN 4000 mm.
Non standard and intermediate diameters are also
Water transmission and distribution (potable available on request.
and raw water)
Sanitary sewerage collection systems and outfalls The standard diameter range in mm is defined as below:
Storm water 100 150 200 250 300 350 400 450 500 600 700 800 900 1000
Hydroelectric penstock lines
1100 1200 1300 1400 1500 1600 1700 1800 1900 2000
Sea water intake and outfalls
2100 2200 2300 2400 2500 2600 2700 2800 2900 3000
Circulating cooling water, make-up and blow
down lines for power plants
Industrial applications FLOWTITE pipe systems are available in initial stiffness
Slip-lining expressed in N/m2 of SN 2500, SN 5000 and SN 10000.
Irrigation/Agricultural Other stiffness classes are available on request.
Desalination Available standard lengths of FLOWTITE pipes are 6 and
Mining 12 meter for diameters above 300mm. Individual lengths
Cooling systems and lengths of 18 meters are also available. Smaller
diameters (DN 250) are only available in 6-meter
!
The use of FLOWTITE pipe systems is virtually unlimited. standard lengths. The standard pressure rating of
N
If you have an interesting application, please do not FLOWTITE GRP pipes is up to 32 bar. Not all pressure
hesitate to contact us. classes are available in all diameters and stiffness. As
O
AMIANTIT feels committed to high quality standards, we
ensure that pipes with PN greater than 1 are 100%
TI
pressure-tested for twice their nominal pressure.
LU
The FLOWTITE product line also includes standard
GRP fittings that are moulded or fabricated using the
same materials that are used to produce FLOWTITE
O
FLOWTITE pipe sections are typically joined using GRP Throughout the world, specialists at our sales offices
double bell couplings. The FLOWTITE double bell offer a wide range of products and product support.
coupling utilizes an elastomeric gasket Type REKA for They will assist and advise on:
sealing. It has been proven in use for more than 90 years.
Other Joining Methods are: Technical consultation with planning, installation
and rehabilitation
Locked joints Local consultation and support for contractors
Loose & Fix GRP Flanges Static and hydraulic calculation
Flexible Steel Couplings Solutions for special applications
Mechanical Steel Couplings Training of installation staff
Lay-up Joints (butt strap) Brochures and information material
Technical drawings
!
N
Standard double bell coupling
O
Installation TI
LU
Due to their outstanding product properties, FLOWTITE
pipe systems can be installed in various ways. Main
installation type is the belowground installation but they
O
aboveground
aerial
subaqueous
by sliplining
R
by microtunneling
W
LO
Utmost care has been taken to
ensure that all the contents of this
brochure are accurate. However,
AMIANTIT and its subsidiaries do
not accept responsibility for any
problems which may arise as a
result of errors in this publication.
Therefore, customers should always
make inquiries into the potential
product supplier and convince
themselves of the suitability of any
products supplied or manufactured
by AMIANTIT and/or its subsidiaries
before using them.
!
N
O
TI
LU
O
Distributed by:
ES
R
AMIANTIT Norway AS
stre Kullerd 3,
3241 Sandefjord
W
Norway
Tel.: + 47 99 11 35 00
LO
Fax: + 47 33 44 92 00
info-no@amiantit.eu
www.amiantit.eu