Professional Documents
Culture Documents
1
TYPEMODEL
1.1 2-1419128-9
OJE-SS-105HM,000
1.2
OUTLINE As per Customer Drawing sheet
1.3 S
CONTACT ARRANGEMENT
1.4
CONTACT MATERIAL Ag alloy
2
SAFETY STANDARD
2.1
Conform with Japan Product Safety Electrical Appliance & Materials law
2.2
FOREIGN STANDARD Recognized by
3
COIL RATING
3.1 DCV
RATED VOLTAGE
3.2
COIL RESISTANCE
3.3 W
NORMINAL OPERATING POWER about 0.45W
3.4
MAX. ALLOWABLE COIL VOLTAGE 130% of rated coil voltage (at 23)
213-8535 3-5-8 1 of 6
Tyco Electronics EC K.K. (3-5-8 Hisamoto Takatsu-ku Kawasaki, 213-8535)
This document is subject to change. Call local Tyco Electronics for the latest
revision.
Copyright 2007 by Tyco Electronics EC K.K. All rights reserved.
* : Trademark
Product Specification 108-79770
4
CONTACT SPECIFICATION
4.1
CONTACT RATING Load Inrush current curry current Cut off current
(A)ACV
4.2
RATED CONTACT CURRENT
4.3
MAX. CONTACT CAPACITY
4.4 (
MIN. APPLICABLE LOAD (reference)
5
PERFORMANCE
5.1 DC6V A
CONTACT RESISTANCE 100 Max. (at initial stage) voltage drop test method 6VDC 1A
5.2 .
OPERATE VOLTAGE 3.75VDC Max. of rated voltage. (at 23)
5.3 .
RELEASE VOLTAGE 0.25VDC Min. of rated voltage. (at 23)
5.4
OPERATE TIME 10ms Max. at rated voltage.
5.5
RELEASE TIME 5ms Max. at rated voltage
5.6
ENDURANCE
(1) (A)
ELECTRICALLY Contact rate A: 100,000ops. Min. (10 ops/minute)
5.7 mA
DIELECTRIC STRENGHT (Leak current: 1mA)
5.9 5kV(1.2/50s)
SURGE RESISTIVENESS Between coil to contact. 5kV (1.2/50s)
Rev. A2 2 of 6
Product Specification 108-79770
5.10
TEMPERATURE RISE
(1)
COIL 55K Max. by resistance method when the rated current is provided to contact
(2) A
CONTACT 60K Max. by temperature measuring method at Contact: 10A, Coil: rated voltage
5.11
VIBRATION
5.12
SHOCK
5.13 5N 10
TERMINAL STRENGTH No construction and exterior trouble when pull and push into any terminals by 5N
for 10sec.
5.14 85 240 2
THERMAL PROOF Not any trouble on construction and characteristic when leave in 85 240h
5.15 40 240 2
COLD PROOF Not any trouble on construction and characteristic when leave in -40 240h
Rev. A2 3 of 6
Product Specification 108-79770
5.16 40 90RH 24 2
10M
HUMIDITY PROOF Insulation resistance 10M Min. Not any troubles on construction and
temp. room for 0.5 h each. That is one cycle. After 100 cycles has done, leave it on
5.19 260 5
SOLDERABILITY Not any problems solder dipped at 260 5 sec.
6
STANDARDS TEST CONDITION
6.1
TEMPERATURE
6.2 RH
HUMIDITY
6.3
DIRECTON OF MEASUREMENT Terminals down position is standard position.
7
OPERATING CONDITION
7.1
TEMPERATURE (On conditions without freezing and dew condensation)
7.2 %RH
HUMIDITY
7.3
MOUNTING DIRECTION Terminal down position is standard position
Rev. A2 4 of 6
Product Specification 108-79770
8
STORAGE CONDITION
8.1
TEMPERATURE (On conditions without freezing and dew condensation)
8.2 RH
HUMIDITY
8.3
ENVIRONMENT
(1)
Store in locations where the product or container is not expose to corrosive gas such as hydrogen sulfide gas
or salty air.
(2)
Store in location where no visible dust exists.
(3)
Store in location not subject to direct sunlight.
9
OTHER
Rev. A2 5 of 6
Product Specification 108-79770
10
CHANGE PROFILE
Rev. A2 6 of 6