Professional Documents
Culture Documents
TRANSAXLE
Bulletin Number
06-40-006
Subject Date
2004~06 TIBURON 2.7L TCM REPROGRAMMING MAY, 2006
PROCEDURE - 2-3 SHIFT FEEL
Model
TIBURON 2.7L
CIRCULATE TO: [ ] GENERAL MANAGER [X] PARTS MANAGER [X] TECHNICIAN
[X] SERVICE ADVISOR [X] SERVICE MANAGER [X] WARRANTY MGR [ ] SALES MANAGER
DESCRIPTION:
Some 2004~2006 Tiburon vehicles with 2.7L engine and automatic transaxle may
exhibit a firm or abrupt 2-3 shift when the automatic transaxle fluid is at normal
operating temperature.
This bulletin provides the procedure to reprogram the Transaxle Control Module (TCM)
software for 2004~06 Tiburon 2.7L vehicles using the Hi-Scan Pro.
NOTE: This reprogramming addresses only the described condition.
VEHICLES AFFECTED:
Model: 2004~2006 Tiburon vehicles with 2.7L gasoline engine and automatic
transaxle.
Affected vehicle production date range: From the beginning of 2004 Tiburon
production through February 28, 2006.
Affected VIN range: From the beginning VIN of 2004 Tiburon through
KMHHN65F46U216032.
Page 1 of 5
CAUTIONS DURING REPROGRAMMING:
1. Perform reprogramming with the ignition key in the ON position.
2. Be careful not to disconnect any cables connected to the vehicle or Hi-Scan Pro
during reprogramming.
3. Do not start the engine during reprogramming.
4. Do not turn the ignition key OFF during reprogramming.
5. When reprogramming is completed, turn the ignition key OFF then wait for 20
seconds. Start the engine to confirm proper operation of the vehicle.
6. After reprogramming is completed, the transaxle control module adaptive
values must be reset (erased), depending on model year as shown below
(Engine off).
Page 2 of 5
Technical Service Group
TRANSAXLE
Bulletin Number
06-40-006
Page 3 of 5
6. The Hi-Scan Pro will establish communication, check the TCM ID, and reprogram
the TCM.
NOTE:
The Hi-Scan Pro detects the current TCM ID, assigns the new TCM ID and
displays them on the Hi-Scan Pro screen.
Check the TCM ID displayed on the Hi-Scan Pro screen to verify that the correct
TCM software is being downloaded. Refer to the "ROM ID INFORMATION
TABLE" on Page 1.
If the Hi-Scan Pro does not download the program, use the "MANUAL
REPROGRAMMING PROCEDURE."
CAUTION: Do not interrupt the reprogramming at any time.
7. When "REPROGRAMMING COMPLETED" message is displayed, turn the ignition
key OFF for 20 seconds and then start the engine to confirm proper operation of
the vehicle.
8. After reprogramming is completed, reset the transaxle control module
adaptive learning values.
9. Check for diagnostic trouble codes and erase any trouble codes.
6-3. MANUAL REPROGRAMMING PROCEDURE
1. Turn the ignition key to the ON position. (Do not start the engine).
2. Turn the Hi-Scan Pro ON.
3. Select option "74. GK 2->3 SHIFT FEEL IMPROVEMENT" and press ENTER.
4. Select option "02. GK 2->3 SHIFT FEEL
IMPROVE. [ERROR]" and press
ENTER.
5. Choose the vehicle type which is correct
for your vehicle by using the "ROM ID
INFORMATION TABLE" and press
ENTER.
Page 4 of 5
Technical Service Group
TRANSAXLE
Bulletin Number
06-40-006
6. Enter the correct password which is correct for your vehicle and press ENTER.
MENU PASSWORD
01. GK 2.7 (-TCS) : 95440-39881 9881
03. GK F/L 2.7 05MY: 95440-39858 9858
04. GK F/L 2.7 06MY: 95440-39859 9859
7. The Hi-Scan Pro will establish communication, check the TCM ID and reprogram the
TCM.
NOTE:
The Hi-Scan Pro detects the current TCM ID, assigns the new TCM ID and
displaysthem on the Hi-Scan Pro screen.
Check the TCM ID displayed on the Hi-Scan Pro screen to verify that the correct
TCM software is being downloaded. Refer to the "ROM ID INFORMATION
TABLE" on Page 1.
CAUTION: Do not interrupt the reprogramming at any time.
8. When "REPROGRAMMING COMPLETED" message is displayed, turn the ignition
key OFF for 20 seconds and then start the engine to confirm proper operation of the
vehicle.
9. After reprogramming is completed, reset the transaxle control module
adaptive learning values.
10. Check for diagnostic trouble codes and erase any trouble codes.
WARRANTY INFORMATION:
Page 5 of 5