Professional Documents
Culture Documents
7. I-beam is produced by
a) Extruding
b) Forging
c) Csting
d) Hot rolling
22. A 3-8 winding rotate with 1800 rpm in magnetic field having 8 poles, its frequency will
be=120hz
23. A wire is connected to constant voltage supply while its length and radius is doubled
a) electric field is half
b) electric field is double
c) heat is unchanged
d) electric field remain same
28. When a new Ni-cd battery is installed, its cell seal is opened and pour electrolyte to ensure the
full charge battery
a) no charge is required
b) charge is given and boost up and (A)
c) as in (b) and suddenly installed in a/c service
d) as in (b) and after two hours, check the electrolyte and installed in service
32. If countersunk is not possible to use on thin sheet to get flush surface, then we can use
a) round head rivet
b) brazier head rivet
c) counter sunk rivet with dimpling
d) flat head
39. When journey from magnetic equator towards pole, the dip and
a) increased
b) decreased
c) depend upon direction
d) none
43. i. Dos is
a) programme
b) processing unit
c) disk operating system
d) all
44. Software is a
a) programme
b) language
c) operating system
d) all
52. When on NPN transistor is used as an amplifier, the electron flow from
a) emitter to base
b) base to collector
c) collector to base
d) base to emitter
56. Algerithm
a) Consists of finite no.of steps has outputs are definite
b) Consists of infinite no. of steps
c) May not have out put
d) None
57. Ceramic fibers are
a) used for high temperature application
b) heat resistant and dissipates heat slowly
c) both a & b
d) none
61. Unix is
a) single operating unit
b) double operating unit (multi purpose)
c) CAD & record of engineering organization
a) = c) =
b) = d) =
71. Hybride is
a) used as a core material in composite
b) two or more different layer of reinforcing material
c) used as a met rise material
d) refrigeration of the film
80. In a venire micrometer, 9 parts of the main scale is devided into 10 parts of the vernier scale
the main scale has the graduation of 1mm. The least count is
a) 0.01 mm
b) 0.020 mm
c) 0.009 mm
d) 0.001
82. In aramid
a) Kevlar has 4 times the strength of aluminum
b) White colour
c) All
d) None
1. C 2. A, B 3. B 4. A 5. D
6. B 7. A, D 8. D 9. A 10. D
8. Monel is____
a) heat treatable and non-treatable
b) non-heat treatable
c) magnetic
d) as in (b) and weldable
10. Which hardering heating (hardness) is best suitable for sleep and alloy
a) Brinell and Barcol
b) Brinell and Rockwell
c) Rockwell and barcol
d) Barcol (soft) and Rockwell
15. If 28 volt current is passed through resistant of 10, the power consumed by that component is
(P=V=V/R)
a) 78.4 watt b) 780 w c)784 w d) 0.78w
19. If the rpm of the driver gear is 60, then the rpm of driven gear is
a) 120 rpm
b) 100 rpm
c) 60 rpm
d) 30 rpm
42. What is the descriptive of the annealing process of steel during and after it has been annealed
a) Rapid cooling, high strength
b) Rapid cooling, low strength
c) Slow cooling, low strength
d) Slow cooling ( high strength) and increasing resistance to wear
45. While testing for magnetic testing, it was found non-magnetic, in nitric acid it was found rapid
action, greenish blue color, the material is
a) Ni-steel
b) 18-8 steel
c) monel
d) CRS
51. The transferring metal from one object to another by chemical and coating is done to protect
the base metal from
a) Corrosion
b) Wear
c) Increase the dimension to protect the base metal against chemical reaction
d) all
52. Improve tensile strength, ductility and sleck (shock) resistance of Mg-alloy casting are
normally
a) Case hardened
b) rotation heat treatment
c) none
56. The magnitude of induced emf produced in a coil, when a magnet is inserted in it, does not
depend upon
a) no. of turns in coil
b) resistance of coil
c) magnetic moment of magnet (magnetic strength)
d) speed of rotation of magnet
68. The ATA-100 specification no. for hydraulic, pneumatic, stabilizers and engine is
a) 55,36,29,77
b) 36,29,55,77
c) 29,36,55,77
d) 29,36,77,55
70. In some large a/c, in the side of main L/G strut, there is a hydraulic jack
a) to jack-up the a/c when one wheel is to be raised
b) to serve the oleo shock strut when a/c is jacked up
c) to jack up the aircraft completely
d) all are correct
71. The precision measuring tool, that is used for measuring crankshaft and main bearing journal
for out of roundness and wear is
a) dial gage
b) depth gage
c) micrometer caliper
d) vemier caliper
1. C 2. B 3. C 4. B 5. A
6. A, C 7. D 8. B, D 9. D 10. B
10. To detect a minute crank using dye penetrant inspection usually requires
a) That a developer is applied to flat surface
b) A longer than normal penetrating time
c) The surface to be highly polished
d) Do not require excessive surface preperation
13. When capacitive reactance becomes equal to inductive reactance of a circuit it is called
a) phase-in
b) phase-out
c) resonant
d) impedance matching
15. When a lead-acid battery is charged by constant current method, then its full charge can be
detected as
a) Three testing of electricity gives same specific gravity value
b) Voltage stops rising
c) Gassing will occurs rapidly
d) All above are wrong
16. What should be the first step of the procedure in sketching an a/c wing skin repair
a) draw heavy guideness
b) may out the repairs
c) block in the views
d) draw extension lines
17. A cathode (election emitter) used in thermionic emission must have following characteristics
a) high matching point
b) high matching strength
c) low work function
d) all above are correct
18. When bolts and rivets are used to joint the metal sheets, then both should be protected from
corrosion by
a) applying grease on both
b) by plating bolt and rivets
c) by painting bolt and rivets
d) they must be placed separately approximately, 2-times than the thickness of the metal being
joined
23. If a line is divided into 25 division so that 25 divisions of this line is equal to 24 division of
another line so that minimum distance that can be measured is equal to difference between the
value of each division . it is the principle of
a) DTI
b) Micrometer
c) Vernier scale
d) Rules
27. For very accurate readings during such calibrations the thimble may be viewed under a
microscope of
a) low magnification
b) medium magnification
c) high magnification
28. When hydraulic fluid lines and electrical line is passing through same portion of a/c, then
a) Hoses should be fitted above the wires and should be secured to a/c structure
b) Electrical wire should be fitted above and to secure to a/c structure
c) A minimum of 4-distance should be maintained between two and any of two can be
unstable above
d) Either of wire can be installed above and a minimum of
42. If the thimble scale zero mark is above the zero mark of barrel mark in micrometer, it indicates
a) positive error
b) negative error
c) zero error
d) none
50. The ability to detect minute crack with radio graphy is called
a) radio graph resolution
b) radio graph sensitivity
c) radio graph processing
d) radiograph density
e) all
51. In plastics, minute crack occurring at weaker area due, to applied load and extends both sides
a) crazing
b) creeping
c) fatiguing
d) crevice corrosion
61. A micro switch will close or open a circuit with the movement of
a) 1 or more c) both a & b
16
b) 1 or less d) none
16
1. B 2. C, D 3. B 4. B 5. C, D
6. C 7. C 8. A 9. C 10. B
61. B 62. B
PAPER II (FEBRUARY 2001)
3. In magnetic and non-magnetic material, coating thickness of ferrous and non-ferrous alloy
should be measured by
a) eddy current
b) magnetic particle test
c) micrometer caliper
d) all
9. When two surfaces fit tightly together, but can move relatively to one another
a) fretling corrosion
b) intergranular corrosion
1. B 2. D 3. A 4. A 5. B
6. - 7. C 8. C 9. A 10. A
1. In 7075-0 indicates
a) annealed
b) strain hardened
c) solution HT
d) none
9. Al-alloy is not heat treated properly to have uniform grain boundaries it has
a) stress corrosion
b) galvanic corrosion
c) intergranular corrosion
d) fretting corrosion
11. Which is used to transfer rivet size from template to new sheet is
a) centre punch
b) pin punch
c) alignment punch
d) transfer punch
12. A side clearance between piston ring and cylinder wall is measured by
a) telescopic gauge
b) thickness gauge
c) micrometer
d) plug gauge
17. In dye penetrant inspection, the defects under while light appers
a) black
b) green
c) red
d) all
20. In ultrasonic test, when mechanical stress vibration is applied to crystal quartz then these are
a) electrical energy and voltage are produced
b) more vibrations are produced
c) as in (A) and varies with the thickness of crystal
d) none
21. Form of corrosion which occurs between metal and non metal is
a) filliform corrosion
b) crevice corrosion
c) exfoliation corrosion
d) fretting corrosion
25. For maximum elongation, ductility, tensile strength and impact resistance Mg-alloy is
a) solution heat treatment
b) casted
c) precipitation heat treatment
d) none
28. An ac circuit consists of inductance of 10, capacitance 4 & resistance 8 the impedance of
the circuit is Z=R+(XL-XC)
a) 6 b) 10 c) 5.5 d) 8
33. The static vents with the flat surface plate at two position to
a) minimize position error
b) have is formation freedom
c) both a & b
d) none
35. An ac circuit has inductance 3 and resistance of 4, then impedance of the circuit is
a) 3 b) 1 c) 5 d) 7
39. Mg is ________
a) Susceptible to corrosion
b) Has tendency to crack
c) Resistance to corrosion
d) Both a & b
42. Rack is mest with a gear, it is used to change (the purpose of rack and pinion is to change)
a) rotary motion to reciprocating motion
b) reciprocating motion to rotary motion
c) both a & b
d) none
OCT 2000
11. The modulation in which, amplitude is kept constant and frequency is changed is called
a) amplitude modulation
b) space modulation
c) frequency modulation
d) phase modulation
13. In NDT of material by Dye penetrant inspection (DPI) the volume of defect is interpreted by
a) Staining rate
b) Staining speed
c) Staining extent
d) All
14. In UST, scanning is carried out by moving both probes simultaneously in opposite direction for
a) flash butt joint (weld)
b) heavy forgings
c) heat treatment defect
d) thickness measurement
16. The fluid use for all types of aircraft engines except rocket is
a) gasoline
b) air
c) ATF
d) All are correct
19. In composites, repair the part is steeped rather than to be scrafed for
a) uniform shear stress
b) uniform tensile stress
c) smoothness
d) both a & b
21. In uniform fluid flow, the fluid is first made to flow through a tube and the pressure exerted by
the fluid is measured by
a) dynamic pressure
b) static pressure
c) reynolds no.
d) all
23. The rust and corrosion is removed from highly stressed steel parts by
a) abrasive paper
b) fine buffling cloth on buffling wheel
c) wire brush
d) all
32. A device which gives lateral control and is mounted at the opposite surface of wing
a) spoiler
b) vertex generator
c) tab
d) flap
1. A 2. C 3. C 4. B 5. D
6. B 7. B 8. C 9. C 10. C
1. A, D 2. C 3. C 4. C 5. D
6. C 7. A 8. B 9. D 10. B, D
7. When material is forced through a die to take the shape of die, is called
a) Forging
b) Rolling
c) Extrusion
d) Casting (Mg)
8. All long extruded parts such as bar, tube, pipe etc are stored
a) horizontally
b) horizontally with well supported along its length
c) vertically inclined at an angle of 60
d) all
9. Bronze is Cu-alloy containing
a) tin
b) zinc
c) titanium
d) all
13. The part which is dry and un lubricated, which of the following occurs
a) erosion
b) abrasion
c) fettlers
d) all
14. In radiography NDT, which of the following factor does not affect the test
a) distance of film and exposure angle
b) time
c) material thickness, density, shape & size
d) film characteristic
23. As per ATA-100 specification, the correct sequence of air conditioning, fuel, navigation and oil
system is
a) 21,28,34,79
b) 21,34,28,79
c) 31,34,52,80
d) 32,28,34,79
26. Axial distance covered by a threaded fastener in one complete revolution is called
a) pitch
b) lead
c) bolts
d) none
29. In engineering drawing, the lines indicate the alternate position of parts or relative position of a
missing part
a) hidden line
b) phantom line
31. What amount of load is acting on the bolt f extension bar is used on the torque wrench as
shown in figure
a) 150 lbs
b) 125 lbs
c) 175 lbs
d) 200 lbs
39. (0.625)10=( )2
a) 0.110 b) 0.101 c) 0.011 d) 0.100
a) I angle projection
b) II angle projection
c) III angle projection
d) Sectional projection
51. For given figure, which is correct a) 0,0,1 b) 1,0,1 c) 1,1,0 d) 1,0,0
AB
C 1
53. When three individual resistance are connected in parallel to each other which of the following
is correct
a) R = R1+R2+R3 b) 1/R = 1/R1 + 1/R2 + 1/R3
ANSWERS:
1. C 2. A 3. D 4. C 5. C
6. B 7. C 8. B 9. A 10. D
4. Flab tab is
a) balance tab
b) trim tab
c) servo tab
d) none
6. Lift depends on
a) wing area
b) wing shape
c) square of velocity and density of air
d) all of above
17. In a transformer is primary frequency changes from 50Hz to 60Hz, keep the pick voltage
constant then frequency
a) increases in secondary by ratio 60/50
b) decreases in secondary by ratio 50/60
c) both 1 & 2
d) none
19. When in a/c is required, embossing, etching and marking then electrical etching done by
a) electrical etching pencil if applied lightly
b) electrical etching pencil but only for CRS
c) electrical etching pencil is prohibited in a/c
d) both 2 & 3
23. When coil of wire is placed horizontal to the earth surface, and a bar magnet dropped from the
top
a) fall with acceleration equal to g
b) fall with acceleration less than g
26. (1010101)
a) (85)10 b) (58)10 c) (64)10 d) none
34. To improve tensile strength, durability, shock resistance Mg. casting are normally
a) SITT
b) PITT
c) Annealing
d) None
2. a) What is the purpose of circuit breakers & lines? What is the property of fuse?
b) What is the purpose of self locking nut? Describe any three types of self locking nut.
c) What are the chemical treatment applicable for Aluminium.
3. a) What are constant voltage & current charging method? Why they are used?
b) Write down truth table for NAND & NOR gates along with a neat sketch? Why they are
called universal gates.
c) What are the methods to control fuel contamination.
5. a) What do you mean by impendance. Calculate the impendance of the given circuit and current
flow in the given circuit.
C 5 micro farad
60 Hz
115 V
b) What are the six special inspection to be carried out on airframe as well as engine.
c) Show with a neat diagram, flexible, extraflexible and non flexible cables.
6. a) Name the various parts of the micrometer & calculate its least count in inch.
b) What is the angle of attack and what are its effects on lift and drag
c) Name the various instruments used for checking the performance of piston engine.
d)Describe the principle of NDT by ECI.
ANSWERS:
1. D 2. C 3. B 4. D 5. D
6. D 7. A 8. C 9. D 10. A
3. Which of the following precision instrument is sued for tightening the nut on bolt with proper
torque is
a) socket wrench
b) torque wrench
c) ratchet wrench
4. For repairing the oversize hole with sleeve, the hole must be drilled oversized by
a) 3/16 b) 1/32 c) 1/64 d) 3/64
14. T6 indicates
a) artificially aged only
b) SHT and cold worked
c) SHT and their artificially aged
d) Solution heat treated
16. A micro switch will open or close a circuit with the movement of
a) 1/16 or less
b) 1/16 or more
c) both
d) none
17. Range of ammeter is extended by connecting a resistor with moving coil in
a) parallel
b) series
c) any one of the above
d) none
33. While starting the piston engine, which type of fire extinguisher is permitted
a) Water and water based agent
b) Co2, 516 capacity
c) Dry chemical
d) CC14 (halon gas)
34. Which core material gives deflection in composite
a) honey comb
b) synthetic resin
c) foam
d) all
37. In PFD, when used fluorascent, material color of defective part and sound part is
a) brilliant yellow-green and blue violet
b) brilliant yellow-green and bright red
c) bright red and blue violet
d) none of the above
38. ATA-100 code of hydraulic power, pneumatic fire and engine oil is
a) 36,26,79,83
b) 29,36,26,78
c) 29,36,26,79
d) 79,36,29,26
45. If no marking of drill, identification of drill can be measured by drill gauge having
a) fraction on right and no. on left
b) fraction on left and no on right
c) both a & b
d) none of the above
52. What size of the hole should be bored before cutting a 2.5 internal acme thread having 3
thread per inch
a) 2.5 b) 2.1667 c) 3.5 d) 2.75
1. B 2. C 3. B 4. C 5. B
6. A 7. B 8. B, D 9. A 10. C
13. If acid is spilled over skin from an a/c battery then it cleaned with
a) water
b) water & boric acid
c) water & bicarbonate of soda
d) all
21. For a battery to have high ampere hour capacity and high terminals voltage
a) low internal resistance
b) high internal resistance
c) does not depend on internal resistance
d) none
45. 1 HP is usual to
a) 735 electric watts
b) 746 electrical watts
c) both a & b
d) none
52. In ATA-100 specification of cable, electrical wire no and letters are marked as
a) prefix and suffix
b) side by side
c) in middle
d) at the end
61. An 12 H5 indicates
a) dia 3/5 and head is not drilled
b) dia 6/8 and head is not drilled
c) dia 6/8 and head is drilled
d) dia 6/8 and shank & head is drilled
69. Speed of motor increase when load decrease current decrease because of
a) frictional loss between motors moving parts
b) frictional loss between field winding and other parts
c) induced back emf increases
d) none
74. When in a/c. it is required embossing, etching and marking, then electrical etching is done by
a) electrical etching pencil, if applied lightly
b) electrical etching pencil but only for CRS
c) electrical etching pencil is prohibited in a/c
d) both b & c
ANSWERS:
1. B 2. D 3. A 4. C 5. D
6. B 7. C 8. A, D 9. D 10. D
4. Seak often forms on the surface of the metal and dirt blocked on it, cleaning of seaks and dirt
from heat threated part is done by
a) steel wire brush
b) sand blasting
c) scap
d) all
10. To prevent solder from running away from the surface to be jointed
a) flux is used
b) temperature is maintained
c) clay is commonly used to surround the area to be jointed
d) all
34. When two sphere of same mass, one id +ve charged and other is ve charged, then new mass
will
a) change
b) unchanged
35. If the conductor is of 4 and it stretched to twice of its length, then its resistance is
a) 1 b) 8 c) 12 d) 16
36. A and B are big and small battery, having same emf. Internal resistance of battery A is
a) less than B
b) greater than B
c) equal to B
d) unaffected
1. C 2. D 3. D 4. D 5. D
6. A 7. B 8. D 9. A 10. C
36. A 37. B
MARCH 1994
3. Oxyacetelene flame with equal volume of oxygen and acytelene gives the types of flame as
shown
a) carbonizing
b) oxidizing
c) neutral
d) there is no such flame
6. Synthetic thermoplastic
a) when heated becomes soft
b) when heated becomes hard
c) when cools become hard
d) both a & c are correct
19. In a micrometer in the main scale each cm divided into 10 equal parts and in circular scale, 9
division of main scale equals to 10 divisions of circular scale the least count of the macrometer is
a) 1mm
b) 0.01 mm
c) 0.01 cm
d) 0.0001 mm
20. In a micrometer the smallest division on main scale is 0.5 mm. The vernier scale is divided into
25 division and it moves one division on the mainscale for complete rotation of the vernier scale
then the least count of the micrometer is
a) 0.01mm
b) 0.002cm
c) 0.01cm
d) 0.001mm
21. In pitot static system static vents are placed separately in a/c to reduced
a) vaccum gauge
b) vaccum chamber
c) micromanometer
d) all
25. In four digit N-alloy index system, no-2024, the first digit indicates_____
a) the % of Al-added
b) the different alloy in this group
c) alloy group
d) copper is the major alloying element
29. Which tool can be used to measure the alignment of a rotor shaft or the place of rotation of disk
a) dial indicator (DTI)
b) shaft gage
c) protector
d) all
35. Flow of aviation fuel which passes greater antiknock quality than 100 octane, classified
a) according to the multiplies of lead
b) by reference to normal neptane
c) by performance number
d) none
41. Which maintenance record entry best describe the action taken by FAR when a 0.125 dent in a
straight section of Al-alloy tubing is found
a) dent is acceptable limit and repair not necessary
b) dented section removed and replaced with identical new tubing flared 45.
c) Dent removed by drawing appropriate size bullet through the tubing
d) Deffered to maintenance check
44. Roller bearing take more radial load than ball bearing of same size because
a) larger contact area
45. In brinell hardness testing, the thickness of material should not be less than
a) 5 times
b) 10 times
c) 20 times
d) 50 times
57. When defuelling is done on swept back wing a/c. best precaution is
a) outboard tank drain first
b) fuselage tank drain first
c) inboard tank drain first
d) all tank drained together
1. D 2. B 3. C 4. A, B 5. C
6. D 7. A 8. A 9. B 10. B
12. In brazing
a) post heat treatment may be carried to relieve stresses
b) post heat treatment may not be carried to relieve stresses
33. The thickness of the conducting and non-conducting coating in ferrous metal can be measured
by
a) varnier coliper
b) varnier micrometer
c) ultrasonic
d) eddy current method
34. To measure the thickness of the hollow tubular member normally done by
a) distructive method
b) eddy current method
c) ultrasonic method
d) none
1. D 2. A 3. C 4. D 5. D
6. B 7. A 8. C 9. D 10. A
1. In a capacitor
a) capacity depends on separation of plates and measured in farade
b) capacity depends on area of plates and measured in farade
c) capacity depends on nature of dielectric material
d) all
7. Nomex is a
a) honey comb material
b) reinforced fibre
c) metrix material
d) none
10. In a dye penetrant test before applying developer, what shall be done
a) dye should be completely flushed out
b) only excessive dye should be removed
c) the rinsing operation is completely carried out
d) both b & c are correct
12. If a magnet is dropped through a current carrying coil, it will fall with
a) uniform acceleration equal to g
b) uniform acceleration less than g
c) non-uniform acceleration more than g
d) non-uniform acceleration less than g
15. Transfer metal from one object to another by chemical and electrical means is done to
a) protect base metal against corrosion and wear
b) increase the dimension of a part
c) protect base metal against reaction
d) all
a) Cam
b) Dowel pin
c) Steel
d) Taper pin
a b
V=0
a) 1/3 from a to b
b) 2/3 from a to b
c) 1/3 from b to a
d) zero
28. In inspection of bolt holes for pits and cracks is carried out
a) before starting reaming
b) after finishing reaming
c) before and after starting reaming
d) done
29. In coolers or radiators where operating temperature is high soldering is not done but
a) soldering can be done with approved flux
b) inert gas welding
c) seam welding
d) spot welding
33. To charge the fire in case of only one tire, the jack should be used
a) to just clear the tire from ground
b) hydraulic jack (single base jack)
c) chockes used with remaining wheel
d) all are correct
35. Kevalor is
a) while gliming cloth
b) 4-times more tensile strength than Al
1. When it is necessary to use electrical connectors where they may be exposed to moisture
Use a special type of moisture proof connector.
4. High tension ignition wires are checked for current leakage with
Hardness tester
5. The wheat stone bridge utilize in a particular type of oil temperature gauge. It is an electrical
device for measurement of electrical resistances and in this instance the resistance of wire bridge
Increase with rise in oil temperature
6. The use of small bundles of wire in a/c electrical system is desirable due to
Better flexibility
11. If the generator output were fluctuating, how would you place a resistor in the line to settle out
the fluctuations
In series with the generator
16. You are about to point a battery compartment, the point should be
Acid resistance paint
19. When an a/c is in flight the cabin hater combustion motor get its, power from the
Battery
20. Landing lights are hooked upto the main line because
High amperage is required
24. The type of control switch used for a retractable landing light is described as
A single pole double throw (SPDT)
26. The voltage regulator has a broken wire in the coil under this circumstances you will obtain
Zero voltage
32. During the operation of a four engine aircraft, which of the following generator controls are
available to the pilot
Each of the four generators has a switch that is in series with each generator field
34. During flight, all the gear, down lock indicator lights burn-out. How would this affect the gear
warning horn system
It would have no effect
35. You are about to install some parachute flares. Before actual installation, you should
Turn both the master switches and flare switch to the off-position
36. During flight, when more electrical power is needed, the generator voltage will
Remain at a constant voltage, however, the current flow will increase
38. The tensile strength of the cable to terminal joints should be at least equivalent to
The tensile strength of the cable itself
39. When frequent disconnections are required in the electrical system, the mechanic should use in
order to facilitate maintenance
Connectors (plugs and receptacles)
40. Soldered electric splices should not be used because they are
Particularly brittle
41. Electric wiring that offers the advantages of case of installation, simple maintenance and
reduce weight is known as
Open wiring method
42. Junction boxes should be mounted with the open side facing downward, this arrangement
permits
Loose metallic objects, such as washers, bolts etc to fall out of the box and prevent possible
short circuits
43. An arcing fault between an electric cable and a metallic flammable, fluid line may puncture,
the line and result in a serious fire, when separation is impracticable, the electrical cable should
Be places over flammable fluid line and securely clamped to the structure
1. D 2. D 3. C 4. D 5.
6. A 7. A 8. D 9. B 10. D
41. B
DGCA LICENCE EXAMINATION PAPER II MAR 94 SESSION
(A/C GENERAL ENGG. & MAINTENANCE PRACTICES)
9. In an alto meter if there is absence of barometer is pressure, the pitot line is checked by:
a) vacuum chamber
b) micrometer
11. In pitot static system the static vent to of the flat plate tube any where in the a/c structure to
prevent.
a) position error
b) instrument error
c) protection against ice formation
d) both a & c are correct
21. The given fault (as per figure) found in spot welding is:
a) porosity crack
b) slashing
c) deforming of weld
d) none of these
22. A screw having no head flush with the structure can be turned by:
a) allean key
b) screw extractor
c) simple screw driver
d) both (a) if have hex grove head and (b)
27. The given tool is used for making spot facing to seal the washer, nut bolt head is:
a) counter sink
b) counter bore
c) reamer
d) any one of them
28. The extended round portion which is indicated by letter A in the above figure is known as:
a) pilot
b) straightner
c) guide
d) all the above are wrong
33. In oxyacetylene, the amount of oxygen and acetylene gases are in equal proportion, as
indicated in figure, is the:
a) neutral flame
b) oxidizing flame
c) reducing flame
d) no flame will be produced in this manner
1. A 2. A 3. C 4. A 5. A
41. C 42. B
SUBJECTIVE QUESTIONS:
12. The best matrix material of composite structure must possess low viscosity easier curing
methods and processing conditions. With good chemical thermal stability. On the above accounts
the best matrix is
a) polyester
b) epoxy
c) phenolic and polyamides
d) bismaleimide
13. Which one of the following types of epoxy resin is best for fire resistance
a) standard DGEBA resin
b) epoxy novolic and cyclo-aliphatic resin
c) halogen Ted epoxy
d) flexible epoxy resin
14. Composite structures are tested using conventional radiographic equipment, however this
method can detect defect of
a) large single void
b) porosity
c) cracks parallel to beam axis
d) cracks normal to beam axis
15. Mark the correct statement in respect to inspection methods used for composite materials
a) the thickness of the laminate and depth of discontinuity does not pose any problem in C
scan method
b) the pulse feature of acoustic emission is analyzed to detect microscopic defect in acoustic
emission method
c) thermos copy is most difficult method since it require material with high thermal
conductivity
d) all the above are correct
16. The deflecting structures like wing should withstand large tensile and compressive load for
which most suitable composite structure is
a) nomad with fiber glass skin
b) sandwich of the fiber glass core and nomad skin
c) sandwich of fiber glass and graphite composite
d) any one of the above method used
(COMPUTER)
18. The capability of the computer system to take logical decisions helps it in
a) making faster calculations
b) storing huge amount of data
c) decision making
d) none of these
25. While revetting if the damage shown in the sketch takes place, it is known as
a) damaged place due to riveting tool
b) cracked head due to hard material
c) rivet tight and plates bulged
d) none of the above is correct
33. For gas welding, while lighting the blow pipe, if flash back occurs, the cause may be due to
a) regulators are not set to correct pressure
b) flow of gas is not ensured before lighting takes place
c) both a & b are correct and over heating
d) none use of spark lighter
41. Scattered dot when viewed under ultra violet radiation indicates
a) fine porosity
b) gross porosity
c) pitting
d) both a & c are correct
42. If a damp flux is used while welding with oxy-acetylene flame, then it will cause
a) porosity
b) lack of penetration
c) craters
d) channeling
44. Which treatment process of metal produces a hard and wear resistant surface area with strong
and tough in core
a) case hardening
b) tempering
c) annealing
d) normalizing
47. While drilling a hole, of the finished hole ahs a rough surface, the cause is
a) dull drill was used
b) the drill penetrated the work very slowly and become very hot while in operation
c) the drill hole was made very rapidly
d) both a & b are correct
61. The isometric view identifying the view indicated by the ref. 6093
1. The most commonly used symbols for electromagnetic flow direction method is
a) UFD
b) MFD
c) PFD
d) EFD
5. Synthetic thermoplastic
a) when heated becomes soft
b) when cooled becomes hard
c) when heated becomes hard
d) both a & c are correct
17. Taking all the factors into consideration the most commonly used metal as electrical
conducting
a) aluminium
b) copper
c) silver
d) iron
18. A galvanometer maybe converted to a voltameter by connecting
a) low resistance coil in parallel with meter
b) high resistance coil in parallel with meter
c) high resistance coil in series with meter to increase range
d) low resistance coil in series with meter
19. In ATA coding system the size and type of the electrical cables/wires in a/c are given by:
a) prefix and suffix
b) side by side
c) numbers and letters
d) none of the above
23. A vernier caliper has least count 0.02 cm and have a negative error 0.02mm reading on main
scale is 0.48 and 6th division of vernier scale coincide with main scale. The reading is
a) 0.485 cm
b) 0.488 cm
c) 0.062 mm
d) none
25. In gear system, a driver and driven on the shaft to get the same direction of rotation
a) bevel gear is used
b) internal and external gear combination is used
c) as in (a) and no mechanical advantage is obtained
d) none
27. To bring the sheet together to get air tight joint, we use
a) draw set
b) cleco fastener
c) aligning camp
d) none
6. An altimeter consists of
a) two aneroid capsules
b) pressure setting knob for adjusting barometric pressure
c) three aneroid capsules
d) all the above are correct
11. In a vernier scale, 24 division are equal to 25 division of vernier so 1cm of main scale is
divided 20 equal parts, find the least count
a) 0.001 cm
b) 0.002 cm
c) 0.002mm
d) 0.001 mm
12. In a vernier micrometer of part of main scale is divided into 10 of scale, the main scale has the
graduations of 1mm find the least count
a) 0.01cm
b) 0.001 cm
c) 0.09mm
d) 0.009 cm
15. Magnesium is
a) susceptible is corrosion
b) corrosion precisiant and light weight
c) has tendency in crack
d) a & c are correct
16. When switch S is open, voltmeter indicates 1.5v and when closed indicates 1.35 v current is 1
Amp what is the internal resistance of the battery
a) Ohm
b) 0.15 ohm
c) 1.35 ohm
d) 1.50 ohm
17. Altimeter is checked by when barometer is not available
a) micro manometer
b) vacuum chamber
21. A transistor is
a) amply the low input signal to high output signal
b) used as a rectifier
c) used in transducer set
d) a & b are correct
31. When selecting a rivet for replacement of a solid rivet, we observe for
a) dissimilar actual corrosion
b) shape of head
c) length of rivet
d) none of the above
35. Though surface of castings and barrs etc removal, by an abrarive cutting tool is called
a) grinding
b) snagging
c) lapping
d) finishing
36. Replace a solid rivet with a hollow rivet we would check for
a) material and compression strength
b) material and shear strength
c) heat treatment
d) material and tensile strength
38. In hot oil and chalk methods the following can not be detected
a) vertical cracks
b) horizontal cracks
c) wavy cracks
d) minute flows and tightly shut cracks
39. The following washers are not used on the part which is exposed to air flow
a) plain washer
b) special washer
c) lock washer
d) a & b
45. Radio graphic inspection, which of the following waves are used
a) X-rays
b) Y-rays
c) Ultraviolet rays
d) a & b
49. For getting high ampere hour capacity and high terminal voltage the plate of cells should be
connected as
a) in series so that to get high internal resistance
b) in series so that to get low internal resistance
c) in parallel so that to get low internal resistance
d) in parallel so that to get high internal resistance
50. Regarding thermal runway which of the following is not correct
a) imbalancing of cells
b) deep cell treatment
c) due to constant current more chances for thermal runaway
d) over heating of a cell
51. For any battery the charged with continent current conditions can be found while changing
a) specific gravity taken at interval of 30 min three consecutive redings should be same
b) gassing will occur
c) voltage stops rising
d) a & b are correct
52. A 35 AH, 12 V battery is discharged according to the following rates which will give max.
capacity?
a) 10 hrs, discharge rate
b) 15 hrs, discharge rate
c) 20 hrs discharge rate
d) 5 hrs discharge rate
56. The motor with two different coils wound on difference sence, which can rotate in two
direction is
a) series
b) shunt
c) compound
d) differentially compound motor
77. The check interior surface condition of cylinders and surfaces, instrument used is
a) boroscope
b) fibrescope
c) endoscope or introscope
d) all of the above
98. Identify:
a) A & D are variable resistors & b & C are fixed resistors
b) A & C are fixed resistors & b & c are variable resistors
c) A & B are fixed resistors & b & d are variable resistors
d) None of the above
99. Identify:
a) potentiometer
b) resistor
c) auto transformer
d) iron transformer
100. Identify
a) AN standard steel bolt
b) Re-worked bolt
c) Magnetically inspected bolt
d) Aluminium bolt
101. Identify:
a) Re-worked bolt
b) Special bolt
c) Magnetically inspected bolt
d) Aliminium bolt
102. Identify:
a) dry cell battery
b) Ni-cd battery
c) Lead acid battery
d) Noneof the above
103. In fluorescent dye penetrant test, the color of the light under which the part is inspected
a) green colour in black light
b) green color in white light
c) ultra violet shining light
d) red color in white light
104. Identify:
a) point, face, edge
b) face, heel, edge
c) edge, face, heel
d) heel, face, edge
105. Identify:
a) anchor, nut with double lug
b) anchor nut with single lug
c) anchor nut at corner lug
d) none of the above
106. Identify
a) cylinder
b) conical
c) rectangular
d) circular
108. Identify
a) circular shaft
b) splinged shaft
c) gear & pinion
d) bearing
109. Identify:
a) gear & pinion
b) buck & gear
c) worm & worm gear
d) none of the above
110. Identical insulated wire coils are hung from air so that they are racing each other and supplied
with same direction A.C.,
a) anti clockwise rotation
b) both are repelled
c) both are attracted to each other
d) clockwise rotation
111. Identify:
a) improper upsetting
b) bucking bar not in place
c) rivet driven too much
d) over sized rivet
112. Which of the following has negative co-efficient of resistance
a) thermistor
b) transistor
c) semiconductor
d) resistor
114. If a wire having a resistance of 4 ohms is stretched twice of its length given its
a) 1 ohms
b) 8 ohms
c) 16 ohms
d) 4 ohms
115. 7 resistors of 20 ohms are connected and battery voltage is 2 volt the ammeter reads
a) 1/10 A
b) 3/10 A
c) 4/10 A
d) 7/10 A
119. Identify:
a) knife edge file
b) mill file
c) three square file
d) none
120. Identify:
a) flat cold chisel
b) single betal chisel
c) diamond point chisel
d) double bend chisel
121. Identify:
a) adjustable tap wrench
b) a) T handle tap wrench
c) T socket wrench
d) Allen wrench
122. Identify:
a) combination wrench
b) box wrench
c) close end wrench
d) crescent wrench
124. identify
a) collet
b) ring gage
c) check gage
d) none
125. The function nut on an a/c landing gear requires a torque of 100 inch pounds. To reach the
nut, a 3 straight adapter must be used on an 15 torque wrench. How many inch pound will be
indicated on the torque wrench when the required torque of the nut is reached?
a) 100
b) 83.3
c) .80
d) 115.6
127. In a vernier micrometer, 9 part of main scale is divided into 10 parts of vernier scale, the main
scale has graduation of 1mm. Find the least count
a) 0.01 cm
b) 0.001 cm
c) 0.001 mm
d) 0.009mm
128. In a given figure, what may be the cause of fault for the installation of rivet?
a) greater allowance on the formal head
b) snap not regular to the head
c) bueking bar not in position
d) none
129. The type of corrosion which occurs when two making surfaces, normally at rest with respect
to one another, are subject t slight relative motion is know as?
a) stress corrosion
b) fretting corrosion
c) crevice corrosion
d) inter granular corrosion
130. The letter: 0 in heat treatment process represents the following condition
a) strain hardened
b) annealed
c) solution heat treated
d) none
131. When an aircraft catches fire, (made of aluminium) conductivity & resistivity of aluminium
respectively
a) increases decreases
b) decreases increases
c) both will increases
d) both will decreases
136. Two wires each one meter long are kept at a distance of 0.02 mt apart if 1 amp current is
flowing through each wire, then force acting on the wire will be
a) attractive if the direction of the current flowing through wires is same
b) attractive if the direction of current will opposite
c) repulsive if direction of current will be reverse
d) both b and c are correct
142. The identical insulated wire coils are hung from air so that they are facing each other and
supplied with same direction
a) both are attracted to each other
b) both are repelled
c) clockwise rotation
d) anti clockwise rotation
146. (Source: after manufacturing apart, it is painted to seal the surface from moisture and for
cosmetic purposes before which decreasing is required for proper adhesion)
148. What is the difference between quantity and quality of X-ray in radiographic inspection?
a) there is no meaning of quantity and quality means the penetrating power of a beam of
radiation
b) quantity is related with penetrating power of X-ray and quality is related with frequency of
X-ray
c) the quantity refers to the amount of radiation penetrating the specimen which affects the
darkness of a radiograph and quality refers to the penetrating power of a beam
d) none above
174. identify
a) bimetallic thermal cut out s/w
b) screwtical disconnect
c) notmally ceased s/w
175. Identify
a) pressure s/w
b) push reset s/w
c) thermal s/w
d) toggle s/w
176. In the absence (substitute) of Baron which composite hybrid may be used
a) Aramid + carbon/graphite
183. In optical instrument used to inspect the interior structure of the components
a) fibroscope
b) boroscope
c) indoscope
d) all of the above
184. If the driven gear teeth ratio is 21:40 what will be the teeth of the driven gear
a) 30:50
b) 30:35
c) 40:55
d) 63:120
188. In a scale 39 division of main scale concides with 10 division of vernier and 1 division of
main scale indicate 1mm. 1 division of vernier scale indicates
a) 0.01cm
b) 0.01mm
c) 1 mm
d) 0.001 cm
189. In a scale 24 main division is concide with 25 division of vernier scale and 1 division of main
scale indicate 1 mm then 9 division of vernier scale indicates
a) 0.004 cm
b) 0.001 mm
c) 0.01 mm
d) 0.01 cm
5. Figure (5.42-5.43, pg. No. 107 and 108 shop theory) shows
a) plug gauge
b) snap gauge
c) ring gauge
d) none
9. O or A indicates
a) anhealed recrystallized
b) quenched
c) forged
d) both a & b
10. As the presence of figure and find the amount of torque applied to a fastener by the torque
wrench
a) 120
b) 150
17. In nitric acid test, the material shows rapid action with greenish blue color, the material is
a) CRS
b) Carbon steel
c) Nickel steel
d) All
21. In a transformer the primary has 200 turns and the secondary has 400 turns. If the supply of
28v is given in primary then the secondary voltage is
a) 70v
b) 110v
c) 50v
d) 24v
Feb - 1999
5. Which tubing has the characteristics (high strength & abbrassive strength) for use un a high
pressure (32,000.psi) hydraulic system of operation of landing gear and flap
a) 2024-T
b) 5052-O Al-alloy
c) CRS
d) 1100-1/2 or 3003-1/2H, Al-alloy
6. Which of the NDT testing method is suitable for the inspection of most metal, plastic and
ceramic surface defects
a) eddy current
b) magnetic particle inspection
c) ultrasonic test
d) dye penetrant method
7. How many of these factors are considered essential of knowledge for x-ray exposure
i) processing of film
ii) material thickness and density
iii) exposure distance
iv) film characteristics
a) 1 b) 2 c) 3 4) 4
8. Which type of crack can be detected by magnetic particle inspection using either circular or
longitudinal magnetization
a) 45
b) longitudinal
c) transverse
d) sub-surface
10. A fibre type self locking nut must not be used on a/c if bolt is
a) under shear load
b) under tensile load
c) subjected to rotation
d) subjected to vibration
13. Considering all factors the most commonly used metal as electrical conductor in a/c is
a) aluminium
b) copper
c) silver
d) tongesten
16. As per ATA 100 code the size & type of electrical wire in aircraft are given
a) by prefix and suffixes
b) side by side
c) at the beginning and at the end
d) by letters and numbers
22. When a gear sector is engaged with a rack the motion will be
a) intermittent rotary
b) reciprocatry
c) intermittent straight line
30. 25 division of vernier scale concides 24 cms of main scale and 1 cm in main scale is divide into
20 equal parts.
a) 0.01 cm
b) 0.05 cm
c) 0.01 cm
d) 0.1 cm
36. In pitot and static system static vents and pitot vents are placed at separate location to prevent
a) position error
b) ice firmation
c) all of the above
38. The phenomenon which causes continuous spin of outer ring due to coincidence of rotor ring
with outer gimble ring axis is called
a) gyro wander
b) apparent precession
c) gyro tumbling
d) gimble lock
41. Which of the following statement are associated with the term fillet
a) the space between the back of one teeth and the knee the following teeth
b) a bounded surface to eleminate and sharp corner
c) the relieved angular cutting edge at a tooth corner
d) the bottom surface of the
5. Dump flux used while welding with oxyacetelene flame will cause
a) porosity
b) crater
c) channeling
6. Alclad is a
a) aluminium alloy sandwiched between for aluminium coating
7. 7075 0 indicates
a) full annealed condition
8. Which of the following revet does not required heat treatment
a) 2017
b) 2117
c) 2024
24. To improve the tensile strength, ductility and shock resistance, magnesium alloy castings
normally
a) case hardened
b) solution heat treated
c) precipitation heat treated
d) solution heat treated
25. Thermistor
a) zero temp. coefficient
b) variable temp. coefficient
c) +ve temp. coefficient
d) ve temp coefficient
26. Circuit containing registor, capacitor, diode, semiconductor is a
a) linear circuit
b) non linear circuit
c) bipolar circuit
d) unipolar circuit
30. If the bar magnet in the fig. Will be removed shown the electromagnetic induction will be
a) oppose the emf
b) act in same direction
c) will not repel but attempt
32. Current is 2.5 amp, voltage 12v, used for 1 minute. How much energy it will consume
a) 1800 J
b) 2 J
c) 60 J
d) 18 J
36. In a blind revet the length between manufacture head to the end is
a) grip length
b) grip range
c) shank length of the revet
38. In a bolt and nut assembly after applying troque, cotter pin hole is not aligning the bolt may be
a) slightly tightened to next slot
b) slightly loosened to next slot
41. Unless specified the troque to be applied to a bolt and nut assembly should
a) degreased dry and clean thread
b) lubricated thread
45. Gyroscope the phenomenon which causes continious spin of outer ring due to coincidence of
rotor ring with cuter gimble ring axis is called
a) gyro wander
b) gyro tambling
c) apparent precession
d) gimble lock
54. Micron is
a) millionth of meter
b) thousandth of meter
59. Least count of 50 divisions on the circle of micrometer whose pitch is 1mm
a) 0.01 mm
b) 0.02 mm
c) 0.5mm
d) 0.002 mm
21. If the temperature of a confined liquid is held constant and its pressure tripled, the volume will
be
a) triple
b) be reduce to 1/3rd its original
c) remain the same
d) none
26. With an ohmmeter connected into the circuit as shown, what will ohmmeter read
a) 20
b) infinite
c) 10
d) none
32. A fibre type, self locking nut must never be used on an a/c if the bolt is
a) under shear loading
b) under tension loading
c) both tension and shear loading
d) subjected to rotation
35. A particular component is attached to the a/c structure by the use of an a/c bolt and a castleted
tension nut combination, if the cotter pin hole does not align with the recommended torque range,
a acceptable practice is
a) exceed the torque range
b) lubricate the threaded section of the nut, bolt and torque
c) change washers and try again
d) change the nut
36. How is a clevis bolt used with a jork-end cable terminal secured
a) with a shear nut lightened to a snug fit, but with no strain imposed on the fork and satefied
with a cotter pin
b) with a castle nut tightened until slight binding occure between the fork and the fitting to
which it is being attached
c) with a shear nut and cotter pin or a thin self locking nut tightened enough to prevent
rotation of the bolt in the fork
d) all are correct
45. What will be the speed of driven gear if driver gear is 120 rpm
a) 60 rpm
b) 120 rpm
c) 100 rpm
d) 240 rpm
2. Sketch and identified ten types of rivets which are used in a/c application
3. An a/c with an empty weight of 21.000 pounds and an empty weight CG +32 was
altered as follows
a) two 18 pounds passenger seats located +73 were remand
b) situation modifications were made at 77+ increasing weight by 17 pounds
c) a sea and safety belt weighting 23 pounds were installed at +74.5 and
6. Sketch with neat and clean diagram of a micrometer and name various parts. Suffers
from turbulance flow
2. The test sample which can be tested by making both probe simultaneously in opposite direction
to detect flames on surface
a) flush butt metal
b) thin sheet metal
c) cast ingot
d) none
5. If a body is given shape and lorituation is exposed to uniform flow of incompressible fluid, each
component of the force which the fluid exerts the body can be expressed as product of
a) area
b) dynamic pressure
c) Reynolds no
d) All
8. N.W.V
a) strength of the compositor material
b) strength of the material and composing with charge
c) strength of reinforcing fibre
d) none
12. If you have some 178 rivet, above 3/16 in dia, that had been aged for the hours after
quenching
a) you could use them frouding they have not exceeded 5 hours of ageing
b) you could not use them because 178 rivets should be used within 10 minutes after
quenching
c) you could use them provided they had not exceeds 3 hours of ageing
17. When welding various metals you may reduce the chances of during by
a) preheating
b) anodizing
c) heat treating
d) clamping
18. Which of the follow of a/c parts or units should not be welded
a) items which are not responsive to heat treatment
b) plain carbon, Ni-steel of SAE 2300 series
c) turn buckle barrel ends
d) steel tubular members of basic structure