carboline
SELECTION DATA
GENERIC TYPE: Modified phosphoric acid etchant.
GENERAL PROPERTIES: CARBOLINE Metal Prep 21 is
4 fast acting, mild, non encrosive acid compound designed
to acid etch nonferrous surfaces. When used as 2 pre-treat
iment for ferrous surfaces, CARBOLINE Metal Prep #1 con:
verts light, tightly adhored rust to black, tightly adhering
iron zine-phosphate complex which serves a5 a base for top:
coats,
RECOMMENDED USES: As an acid etchant for the prep:
aration of aluminum and galvanizing for topcoating, To be
Used where CARBOLINE 1037 WP is nat
due to high temperature considerations. Can also be used! as
a pretreatment for lightly corroded steel structures which
cing
‘cannot be sandblasted prior to pat
NOT RECOMMENDED FOR: Use in conjunction with any
zine primer, organic oF inorganic, oF immersion service.
Do not use on heavily rusted surfaces.
CHEMICAL RESISTANCE GUIDE.
quide for selected topcoat
Consult resistance
TEMPERATURE RESISTANCE: Consul
{or selected topeoat
existance quide
SURSTRATES: Light'y custed steet, aluminum, galvanizing
‘or others as recommended.
TOPCOAT REQUIRED. May be topcoated with most
Drganic eaatings. Recommendations include most CARBO.
LINE low to mediue film build coatings with the excep:
ton of zinerich products, CARBOLINE Meta
rust be topeoated within three to four days of application
Prep #
Oct. 84 Replaces Fets 80
hage meow por tavaeNO OW" MARRAATY Oh CUAMANTEE DF AN
STS RSs wencan a Y AND FINES FON A PAPTIEULAN PURPOSE
product data sheet
CARBOLINE” METAL PREP # 1
Excossive CARBOLINE Metal Frop #1 must be rinsed off =
with fresh water prior to topcocting, a
COMPATIBILITY WITH OTHER COATINGS: Apply
directly to substrate, Will not damage acid resistant coatings
f ringed off promptly.
SPECIFICATION DATA
RECOMMENDED WET FILM THICKNESS PER COAT:
4 mils (100 microns). CARBOLINE Metal Prep ¥1 is non
film forming.
THERE IICAL COVERAGE PER GALLON:*
1600 emi sq.ft. wer (39.1 su, m/l at 25 microns!
400 sq. ft at 4 mils wet (9,8 sa, mil at 100 microns)
“NOTE: Material tosses during application will vary due to
configuration and must be taker into consideration when
estimating job requirements
SHELF LIFE
75°F (24°C
Twelve months minimum when stored at
COLORS: Clear only.
ORDERING INFORMATION
Prices may be obtained from C:
or main office
oline sales representative
APPROXIMATE SHIPPING WEIGHT
Ve
CARBOLINE Metal Prep #1. 12 hs
(5 ks! (25 8 kei
FLASH POINT:
CARBOLINE Metal Prep 1
None, water haseMPso
CARBOLINE METAL PREP #t
APPLICATION INSTRUCTIONS
(ractart and application pra
‘adn, Theta nsvuctione should He fllowed cisely to obcain the mani
SURFACE PREPARATION: Remove any oil or grease
from surtace to be teeated with clean rags soaked in CAR.
BOLINE Thinner #2 or toluol in accordance with SSPC SP
1.22, Remove loose rust or scale if present.
MIXING: May be thinned with water for very mild etehing
fof aluminum of galvanizing, of very light rust. Normally.
Used without theaning,
APPLICATION TEMPERATURES
Material surfaces
Normal s01o0rF (438°C) = c0-140°F 14 80°C
Minimum 35°F 20) 38°F 12°C)
Maximum 50°F (66°C) 150°F (66°C)
Ambient Humidity
Normal 010d 438°C) NA
Minimum 35°F (°C) 0%,
Maximum 20°F (49°C) 99%
0 not apply to camp or wer surfaces as water reduces the
‘etching process.
Wg Strumed “cna ten proper Broduct Teconisengatns hase fan
‘SPRAY: Use tow pressure Hudson type garden sprayer with
hhand pressure pump only. Do nat use high pressure equip,
BRUSH OR ROLLER: Use a medium bristle brush oF short
rap roller
NOTE: Use protective clothing and safety equipment to
prevent contact with skin and eyes,
DRYING TIMES: CARBOLINE Meat Prep #41 must be
tinged untii neutralized with fresh water after 30 minutes
and painted as soon as possible after the water evaporates
On some altays, CARBOLINE Metal Prop #7 torms a white
powder which must be removed before painting proceeds
‘The surface should be coated within 24 hours, ar sooner
there is possible contamination
GLEAN UP: Use water to cloan up,
STORAGE CONDITIONS: Store indoors.
Temperature: 35°F (2°C) to 150°F (68°C)
Humidity: 0-100%
CAUTION: KEEP AWAY FROM SPARKS AND OPEN FLAMES IN CONFINED AREAS WORKMEN MUST WEAR FRESH AIRLINE RESPIRATORS
NOBEASENSHIIVE PERSONS SHOUD WEAR QLOVES OR USE PROTECTIVE CREAM ALL ELZCIAIC EQUIPMENT AND INSTALLATIONS SHOULD
BE MADE ANG GROUNLED IN ACCORDANCE WITH THE NATIONAL ELEGTNCAL CODE IN AREAS WHERE EXPLOSION HAYRFOS EXIST
WORKMEN SHOULD SE REQUIRED TO USE NONFEAROUS TOOLS AND TO WEAR CONDUCTIVE ANO NONSPARKING SHOES
oecarboline
SELECTION DATA.
GENERIC TYPE: SoWent-cleaner blend
GENERAL PROPERTIES: A surtace treating agent for pre
Daring previously coated surtaces for recoating after they
hhave been allowed to cure past recommended reeoat times
or have been exposed 10 sunlight for extended periods of
time,
RECOMMENDED USES: Phenoline’ tank coatings which
hhave cured past their recommended recoat times and Carbo:
‘mastics® of other epoxy coal-tars which have been exposed
to sunlight for 36 hours or mote
THEORETICAL COVERAGE: 400 800 sa, ft. per gallon
(9.8-19.6 mé/1) (depends on surtace roughness and con
tours)
APPLICATION
SURFACE PREPARATION: Wine the surface thoroughly
with clean rags soaked in Surface Preparation #1, Renew
Fag when it becomes contaminated. All surfaces must be
wiped.
CAUTION: WORKMEN MUST WEAR SOLVENT RE
SISTANT GLOVES AND EVE PROTECTION WHEN,
Feb. 81 Replaces April 73
‘CAUTION. CONTAINS FLAMMABLE SOLVENTS Keen
EXPLOSION HAZARDS. EXIST, WORKMEN. SHO
NONSPARKING SHOES
WAY FROM SPARKS AND OPEN FLAMES IN.
FRESH AIRLINE RESPIRATOR HYeEASE NS VP FERGONS SHOULD Wi AR GLOVES O USE PROTEC
AND INSTALLATIONS SHOULD BE MADE AND GHOUNDED IN ACCO"UANCE WITH THE NATIONAL
ho ae REQUINES.
product data sheet
CARBOLINE’
SURFACE PREPARATION # 1
SPECIFICATION DATA
Prices may be obtained trom Carboline Sales Representa:
tive or Main Office. Terms — Net 30 days.
suippinc weicHT:
a Ss
Carwotine Surface
Preparation #1 Bibs. 3.6ka) 40 bs. (18.240)
FLASH POINT: (Ponsky Martens Gosed Cup)
Carboline Surface Preparation #1 73°F (23°C)
INSTRUCTIONS
USING CARBOLINE SURFACE PREPARATION #1.
AVOID LIQUID TO SKIN CONTACT. IF SPILLED ON.
SKIN, FLUSH WITH CLEAN WATER, USE IN WELL
VENTILATED AREA.
STORAGE CONDITIONS:
Temperature: 40-110°F (449°C) Humidity: 0.100%
ONFINEO AREAS WORKMEN MUST WEAR
IWECREAM ALLELECTRIGEOUINENT
ELECTRICAL CODE. IN AREAS WHERE
[F NONCEDRONS TODLS AND TO WEAR. CONDUCTIVE AND
carboline
= Fem
etsSELECTION DATA
GENERIC TYPE
Water-based dispersant
GENERAL PROPERTIES: A water based dispersant
which removes hydrocarbon and other contaminants,
from painted of unpainted surfaces.
+ Biodegradable - 8.0.0./C.0.D. determination
+ Non-lammable
+ Minimum Toxicity Water based
RECOMMENDED USES: — For cleaning contaminated
painted or unpainted surfaces prior to the application of
coatings. May be used for the general clean-up of oil
Figs, equipment, engines, ete
SUBSTRATES: Painted or unpainted steal, galvanized
steel, stainless steel and other nonferrous metals. or
concrete surfaces.
COMPATIBLE COATINGS: May be used to clean
properly cured acrylics, alkyus, epoxies, phenolics,
polyurethanes and others as recommended. After the
cleaned surface has been rinsed and dried per the
application instructions the surtace is suitable for the
application of most generic types of coatings,
March 97 Replaces March 89
product data sheet
SPECIFICATION DATA
VOLATILE ORGANIC CONTENT:
As supplied: 0.4 ids.jual. (54 grt
COVERAGE: One $5 gallon drum at a 10:1 dilution ratio
can clean approximately 150,000 fr’ (13,935.
STORAGE CONDITIONS: Store indoors
Temperature: 40:1 10°F [443°C] Humidity: 0-100%
SHELF LIFE:
j2aec)
24 months when stored indoors at 75°F
KEEP FROM FREEZING DURING STORAGE AND
SHIPPING,
ORDERING INFORMATION
Prices may be obtained from your Corboline Sales
Representative or Carboline Customer Service Qepart
ment
APPROXIMATE SHIPPING WEIGHT:
Eel $5.GsLOum
CARBOLINE SURTACE CLEANERS —4aibs 538 Ibs
(are) (245 Kal
FLASH POINT: (Setaflash)
CARBOLINE SURFACE CLEANER 3. >212°F (100°C)
cCarboline | cARBoLINE’ SURFACE CLEANER 3
VOG
ovo0400
APPLICATION INSTRUCTIONS
CARBOLINE® SURFACE CLEANER 3
Peres ete
SURFACE PREPARATION: Remove all extremely heavy
deposits “blobs” of oil, grease, dirt, etc. from the
surface by scraping with a putty or broad knife.
MIXING: Use full strength tor the most difficult
contaminant removal. ‘May be diluted up to. 10 paits of
potable water to 1 part SURFACE CLEANER 3
depending upon the nature of te contaminant to be
remaved and the type of surface coating present
APPLICATION CONDITIONS:
Moterial Sur
Humidity
Normal 60.85°F 60.85°F —60.90°F 0.80%
(16.28%) (16.29°C)_(16.32°C)
Mioimum 40°F 588 35°F 0%
waco) 480) 1)
Maximum 10°F «1258F = T10°F «98%
usec) 18290) aac)
March 97 Replaces March 89
‘itumec tht the Hope product recammendators have been nace, These inatctara Pred ba followed cussy fo abla fhe man ran seit
APPLICATION TECHNIQUES: Apply using brush or
‘spray. Cover tha surface to be cleaned completely with
the SURFACE CLEANER 3 solution. Heavy depasits:
‘may require a soak in time of 10 to 15 minutes, A light
‘Scrubbing oF brushing action will decrease cleaning time
‘and may be required to removed the heaviest deposits,
Attor use, rise the area Dioroughly with clean potable
pressurized water. Where surfaces are to be painted
following cleaning, lave the SURFACE CLEANER 3 on
long enough so that mo beads of water (water DYER)
remain after rinse. off
CLEAN UP: Use clean potable water.
@AUTION: HYPERSENSITIVE PERSONS SHOULD WEAR
GLOVES OR USE PROTECTIVE CREAM. “REFER TO THE
MATERIAL SAFETY DATA SHEET FOR PRECAUTIONS,
‘CAUTION, CONTAINS COMBUSTIBLE SOLVENTS. KEEP AWAY FROM SPARKS AND OFEN FLAMES. IM CUNFINED AREAS WORKMEN MUST WERK
FoESH AIRLINC RESPIRATORS. HYPERSENGITIVE PERSONS SHOULD WEAR GLOVES UR Use PnOTECTIVE CHeAM. ALC ELECTIIC EGUIPMENT AND
INSYALLATIONS SHOULD BE MADE ANO.OROUNDED In ACCORDANCE WITH THE NATIONAL ELECTMC cOOE. IN AREAS WHERE EXPLOSION
Nazasos FIST, WORKMEN SHOULO Be REGUIRED To USE NONFEAROUS TOOLS AND 10 WEAR CONDUCTIVE ANO NONSPARKING SHOES.