Professional Documents
Culture Documents
Power off the Network Camera as Keep the Network Camera away from
soon as smoke or unusual odors water. If the Network Camera becomes
are detected. wet, power off immediately.
Contact your distributor in the event of Contact your distributor in the event of
occurrence. occurrence.
Do not place the Network Camera Refer to your user’s manual for the
around heat sources, such as a operating temperature.
television or oven.
Keep the Network Camera away Do not place the Network Camera in
from direct sunlight. high humidity environments.
EN - 1
Do not place the Network Camera Do not touch the Network Camera
on unsteady surfaces. during a lightning storm.
EN - 2
English
1 Check Package Contents
ST7501
Central Management Software
EN - 3
2 Physical Description
Front Panel
Antenna
(IP7154 only)
Status LED
Back Panel
Antenna
(IP7154 only) External/Internal
Microphone Switch
Lens
Focus Controller
Zoom Controller
EN - 4
English
3 Mounting the Lens to the Camera
1. Mount the lens by turning it clockwise onto the camera mount until it stops. If
necessary, turn the lens counterclockwise slowly to achieve the best optimum
spacing.
2. Connect the lens cable plug to the camera connector.
3. Unscrew the zoom controller to adjust the zoom factor. Upon completion, tighten the
zoom controller.
4. Unscrew the focus controller to adjust the focus range. Upon completion, tighten the
focus controller.
1 ∞ N
4
T
W
2 3
For further setup, please refer to the lens' instruction manual inside the
lens package.
EN - 5
4 Network Deployment
POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5
Ethernet Switch
EN - 6
English
Power over Ethernet (PoE) (IP7153 only)
When using a PoE-enabled switch
This Network Camera is PoE-compliant, allowing transmission of power and data via
a single Ethernet cable. Follow the below illustration to connect the Network Camera
to a PoE-enabled switch via Ethernet cable.
POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5
PoE Switch
POWER LINK
COLLISION RECEIVE
1 2 PARTITION
3 4 5
Non-PoE Switch
EN - 7
5 Assigning an IP Address
1. Install "Installation Wizard 2" from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network
is analyzed, please click on the "Next" button to continue the program.
Installation
Wizard 2
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches
the one labeled on the bottom of your device to connect to the Network Camera via
Internet Explorer.
Network Camera
Model No:IP7153 00-02-D1-07-04-17 192.168.0.219 IP7153
MAC:0002D1070417
0002D1070417
RoHS
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Pat. 6,930,709 Made in Taiwan
EN - 8
English
6 Ready to Use
For further setup, please refer to user's manual on the software CD.
EN - 9
7 Configure the Wireless Connection (IP7154 only)
le/Hub
ADSL/Cab
AP
POWER LINK
COLLISION RECEIVE
1 2 3 4 PARTITION
5
Note:
te:
1. SSID, abbreviated from Service Set Identifier, is the name assigned to the wireless
network. The IP7154 factory SSID setting is set to "default".
2. Select "Ad-Hoc" wireless mode if you want the IP7154 to communicate without
using an AP or wireless router.
For further setup, please refer to the user's manual on the software CD.
EN - 10
Progressive Scan CCD
IP7153/IP7154
This guide describes the basic functions of IP7153/IP7154.
All detailed information is described in the user's manual.
P/N: 625009000G Ver.1.01
Copyright 2009 VIVOTEK INC. All right reserved.
IP Sur veillance