Professional Documents
Culture Documents
Mechanical Engineering
(Afternoon Session : 04-02-2017)
MADE EASY has taken due care in making solutions. If you find any discrepency/typo/
technical error, kindly share/post your views.
If you want to contest the answer key given by MADE EASY, kindly post your suggested
answer with detailed explanations.
Students are requested to share their expected marks in GATE 2017.
www.madeeasy.in
Corporate Office: 44-A/1, Kalu Sarai, New Delhi - 110016 | Ph: 011-45124612, 9958995830
Delhi | Hyderabad | Noida | Bhopal | Jaipur | Lucknow | Indore | Pune | Bhubaneswar | Kolkata | Patna
GATE 2017 : Examination
Mechanical Engineering | Session-2
SESSION 2
Q.1 Two coins are tossed simultaneously. The probability (upto two decimal points
accuracy) of getting at least one head is _______________.
Ans. (3/4)
Q.2 The emissive power of a blackbody is P. If its absolute temperature is doubled, the
emissive power becomes
(a) 2P (b) 4P
(c) 8P (d) 16P
Ans. (d)
Eb T4 (Stefan Boltzmann Law of Radiation)
Eb2 4
2T
Eb1 = Eb2 = 16P
T
Q.3 If a mass of moist air contained in a closed metallic vessel is heated, then its
(a) relative humidity decreases (b) relative humidity increases
(c) specific humidity increases (d) specific humidity decreases
Ans. (a)
1
2
1
2
DBT
V2 p1
(a) p1V1 ln (b) p1V1 ln
V1 p2
V2 p2
(c) RT ln (d) mRT ln
V1 p1
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 2
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (b)
Work done on the system is considered as positive, so
W = pdV (ve sign during compression)
2 2 2
dV dV
W = pdV = mRT = mRT
1 1
V 1
V
V2 p p
= mRT ln = mRT ln 1 = p1V1 ln 1
V1 p2 p2
Q.5 For a loaded cantilever beam of uniform cross-section, the bending moment (in Nmm)
along the length is M (x) = 5x 2 + 10x, where x is the distance (in mm) measured
from the free end of the beam. The magnitude of shear force (in N) in the cross-
section at x = 10 mm is ____________.
Ans. (110 N) X
(BM)X X = MX X = 5x2 + 10x x
(S.F)X X = FX X = ?
We know that at section X X, X
L
d
FX X = [5 x2 + 10 x ]
dx
FX X = 10x + 10
(FX X)x = 10 mm = 10(10) + 10 = 110 N
Q.6 A cantilever beam of length L and flexural modulus EI is subjected to a point load
P at the free end. The elastic strain energy stored in the beam due to bending
(neglecting transverse shear) is
P 2L3 P 2L3
(a) (b)
6E I 3E I
PL3 PL3
(c) (d)
3E I 6E I
Ans. (a)
Let U is the S.E. in the beam due to B.M. (M)
X
L x
(M )2 d x L (P x)2 d x
U = x x =
0
2(E I ) x x 0
2E INA
L
L
P2 P 2 L3 x
U= x 2 (d x) =
2E IN .A 0 2E I 3
P 2L3
U=
6E IN .A.
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 3
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.7 Which one of the following statements is TRUE for the ultrasonic machining (USM)
process?
(a) In USM, the tool vibrates at subsonic frequency.
(b) USM does not employ magnetostrictive transducer.
(c) USM is an excellent process for machining ductile materials.
(d) USM often uses a slurry comprising abrasive-particles and water.
Ans. (d)
Ultrasonic Machining uses an abrasive slurry which transfers the impact load
provided by the by vibrating to the work piece.
Q.8 Consider a laminar flow at zero incidence over a flat plate. The shear stress at the
wall is denoted by w . The axial position x1 and x2 on the plate are measured from
the leading edge in the direction of flow. If x2 > x1, then
(a) w x1
= w x2
=0 (b) w x1
= w x2
0
(c) w x1
> w x2 (d) w x1
< w x2
Ans. (c)
Laminar flow over plate
As per Blasius
0.664
Cf x =
Re x
and Cf x =
1 2
u
2
0.664
= 1
u x u 2
2
1
x
as x2 > x1
2 < 1
Ans. (d)
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 4
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (b)
f (t ) = tet
1
L (t ) =
s2
By first shifting rule
1
L (tet ) =
(s 1)2
Q.11 The heat loss from a fin is 6 W. The effectiveness and efficiency of the fin are 3 and
0.75 respectively. The heat loss (in W) from the fin, keeping the entire fin surface
at base temperature is ____________.
Ans. (8)
qactual from fin = 6 watt
qactual
fin = i.e. when entire fin at base temperature
qmax. possible
qact. 6
= = = 8 watt
0.75 0.75
Q.12 The standard deviation of linear dimensions P and Q are 3 m and 4 m, respectively.
When assembled, the standard deviation (in m) of the resulting linear
dimension (P + Q) is ____________.
Ans. (5)
According to Root Sum Square or RSS model
n
a = 2i
i =1
a = P2 + Q2 = 32 + 42 = 5 m
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 5
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.13 A steel bar is held by two fixed supports as show in the figure and is subjected
to an increase of temperature T = 100C. If the coefficient of thermal expansion and
Youngs modulus of elasticity of steel are 11 106 /C and 200 GPa, respectively,
the magnitude of thermal stress (in MPa) induced in the bar is _______.
Ans. (220)
We know that for completely restricted expansion, thermal stress developed in bar
is given by
th = (T)E = 11 106 100 200 103
= 220 MPa (comp. in native)
Q.14 For a single server with Poisson arrival and exponential service time, the arrival rate
is 12 per hour. Which one of the following service rates will provide a steady state
finite queue length?
(a) 6 per hour (b) 10 per hour
(c) 12 per hour (d) 24 per hour
Ans. (d)
For steady state, >
as = 12 cust/hr, we should go with option (d) 24/hr
Q.15 A sample of 15 data is as follows: 17, 18, 17 17, 13, 18, 5, 5, 6, 7, 8, 9, 20, 17,
3. The mode of the data is
(a) 4 (b) 13
(c) 17 (d) 20
Ans. (c)
Mode means highest number of observations or occurrence of data most of the time
as data 17, occurs four times, i.e., highest time. So mode is 17.
Q.16 A mass m is attached to two identical springs having constant k as shown in the
figure. The natural frequency of this single degree of freedom system is
k k
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 6
GATE 2017 : Examination
Mechanical Engineering | Session-2
2k k
(a) (b)
m m
k 4k
(c) (d)
2m m
Ans. (a)
Equivalent stiffness k eq = k + k = 2k
k k
Natural frequency is
keq 2k m
n = =
m m
Ans. (50)
Given state of stress condition indicates pure shear state of stress.
For pure shear state of stress,
Max. tensile stress = Max. comp. stress
= Max. Shear stress = XY = 50 MPa
Hence, Max. normal stress = 50 MPa
Ans. (0)
F = y i + x j
F = (y ) + ( x)
x y
=0 + 0 = 0
Q.19 The determinant of a 2 2 matrix is 50. If one eigenvalue of the matrix is 10, the
other eigen value is ____________.
Ans. (5)
The product of eigen value of always equal to the determinant value of the matrix.
1 = 10 2 = unknown A = 50
1 2 = 50
10 (2) = 50
2 = 5
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 7
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.20 Given the atomic weight of Fe is 56 and that of C is 12, the weight percentage of
carbon in cementite (Fe3C) is ____________.
Ans. (6.67)
12
100% = 6.67%
56 3 + 12 1
Ans. (c)
In metal forming there will be increased mechanical properties due to change in grain
size and work hardening.
Ans. (2)
Given variable loading is a completely reversed fatigue or variable loading because
max = min
Hence, mean = m = 0; variable = v = max
For completely reversed fatigue loading Soderberg, Goodman, Gerber and strength
criterion will give same results.
As per strength criterion,
failure stress
max per or
F.O.S.
Endurance limit
max =
N
Endurance limit 100
N= = =2
Max. stress 50
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 8
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (b)
Crystal Structure of materials
FCC: Ni, Cu, Ag, Pt, Au, Pb, Al (soft)
BCC: V, Mo, Ta, W (hard material)
HCP: Mg, Zn
Cobalt HCP < 420C, FCC > 420C
Chromium HCP < 20C , BCC >20C
Glass: Amorphous
BCC: Ferrite or -iron -ferrite or -iron
FCC: Austenite or -iron
Ans. (d)
Q.25 In a slider-crank mechanism, the lengths of the crank and the connecting rod
are 100 mm and 160 mm, respectively. The crank is rotating with an angular velocity
of 10 radian/s counter clockwise. The magnitude of linear velocity (in m/s) of the piston
at the instant corresponding to the configuration shown in the figure is _______.
160 mm
100 mm
10 rad/s
A C
Ans. (1 m/s)
A I (I14)
I23 24
3
= 10 rad/s
2
1 2
4 I34
I 12
1 B
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 9
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.26 A strip of 120 mm width and 8 mm thickness is rolled between two 300 mm diameter
rolls to get a strip of 120 mm width and 7.2 mm thickness. The speed of the strip
at the exit is 30 m/min. There is no front or back tension. Assuming uniform roll
pressure of 200 MPa in the roll bite and 100% mechanical efficiency, the minimum
total power (in kW) required to drive the two rolls is ____________.
Ans. ( )
This question is wrong. For proper calculation we need velocity of neutral plane or
velocity of roller. But in this question velocity of exit is given. From velocity of exit
we may assume the velocity of neutral plane but can't calculate correctly.
After IITs' answer we will challenge and confirm the answer. I have given best answer
for this question.
Method
Method-- I:
a T=Fa
R
F
ho hf
a R
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 10
GATE 2017 : Examination
Mechanical Engineering | Session-2
P
2m
45
O Q
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 11
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (7.5)
L= 2m
M = 10 kg
g = 10 m/s2
Both the surfaces are smooth
3g
&& = = sin
2L
3 10
= sin45 [ Q = 45]
2 2
3 10 1 30
a= = = 7.5 rad/s2
2 2 2 4
Q.28 For the laminar flow of water over a sphere, the drag coefficient CF is defined
as CF = F /(U 2D2), where F is the drag force, is the fluid density, U is the fluid
velocity and D is the diameter of the sphere. The density of water is 1000 kg/m3.
When the diameter of the sphere is 100 mm and the fluid velocity is 2 m/s, the drag
coefficient is 0.5. If water now flows over another sphere of diameter 200 mm under
dynamically similar conditions, the drag force (in N) on this sphere is _________.
Ans. (80)
For sphere-I, = 1000 kg/m3, D1 = 100 mm = 0.1 m, U1 = 2 m/s, CF 1 = 0.5
For sphere-II, D2 = 200 mm = 0.2 m
Since, Dynamically similar conditions,
C F 1 = CF 2 = 0.5; U1 = U2 = 2 m/s
Drag force, 2 2
F1 = CF 1 (U1 D1 ) = 0.5 (1000 2 2 0.1 0.1) = 20
N
F1 CF 1(U12D12 )
=
F2 CF 2 ( U22 D22 )
20 D2 0.01
= 12 =
F2 D2 0.04
F2 = 80 N
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 12
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (b)
Lf L0 10 20
E = = = 0.5
L0 20
T = ln[1 + E] = ln[1 0.5] = 0.693
m
m
is rotating at a constant angular velocity of
0
10
20 radian/s counterclockwise. The magnitude of 2
20 rad/s
Ans. (243.310) x
O
y
v
2
P
1
20 rad/s
x
O
m
m
0
10
V = 6 m/s
= 20 rad/s
Here the centripital and corialis acceleration will be there
apc = 2v = 2 6 20
= 240 m/s2
2 2
apr = r = (0.1)(20)
2
= 40 m/s
Total Acceleration:
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 13
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.31 A calorically perfect gas (specific heat at constant pressure 1000 J/kgK) enters and
leaves a gas turbine with the same velocity. The temperature of the gas at turbine
entry and exit are 1100 K and 400 K, respectively. The power produced is 4.6 MW
and heat escapes at the rate of 300 kJ/s through the turbine casing. The mass flow
rate of the gas (in kg/s) through the turbine is
(a) 6.14 (b) 7.00
(c) 7.50 (d) 8.00
Ans. (b) Q
i
cp = 1 kJ/kg-K
Vi = Ve (Inlet and exit velocity same)
W& C.V = 4.6 MW = 4.6 103 kW
Q& = 300 kW
e
Applying SFEE,
1 1
m& (hi + Vi2 + gz i ) + Q& = m& (he + Ve2 + gze ) + W& C .V .
2 2
&
m& cp (Ti Te ) + Q = W& C.V . (Let zi = ze)
Ans. (6)
Max. shear stress induced in spring wire of a helical compression spring is given by,
8WD 8WC
max = 2
kW or kW
d d 2
1 D
max [ W1 = W2 = W; C1 = C2 (i.e., C = )
d 2 d
(kW)1 = (kW)2 = kW]
2
2 d1
=
1 d2
2
2 d
= 2 = 6 MPa
24 2d
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 14
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.33 Three masses are connected to a rotating shaft supported on bearing A and B as
shown in the figure. The system is in a space where the gravitational effect is
absent. Neglect the mass of shaft and rods connecting the masses. For m1 = 10
kg, m2 = 5 kg and m3 = 2.5 kg and for a shaft angular speed of 1000 radian/s,
the magnitude of the bearing reaction (in N) at location B is __________.
y
y m2
m2
0.1 m 0.1 m
120
0.2 m
0.1 m
m1 x m1 z
A B
0.4 m
120
m3
m3
Ans. (0)
y
y m2
m2
0.1 m 0.1 m
120
0.2 m
0.1 m
m1 x m1 z
A B
0.4 m
120
m3
m3
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 15
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.34 In an orthogonal machining with a tool of 9 orthogonal rake angle, the uncut chip thickness
is 0.2 mm. The chip thickness fluctuates between 0.25 mm and 0.4 mm. The ratio of
the maximum shear angle to the minimum shear angle during machining is ____________.
Ans. (1.494)
Given = 9
t = 0.2 mm
tc max = 0.4 mm
tc min = 0.25 mm
0.2
rmax cos cos9
tanmax = = 0.25
1 rmax sin 0.2
1 sin9
0.25
or max = 42.09
0.2
rmin cos cos9
tanmin = = 0.4
1 rmin sin 0.2
1 sin9
0.4
or min = 28.18
max 42.09
Ratio = =
min 28.18 = 1.494
Q.35 Consider the differential equation 3 y (x) + 27 y (x) = 0 with initial conditions
y (0) = 0 and y (0) = 2000. The value of y at x = 1 is ____________.
Ans. (34.89)
The direction is 3y (x) + 27y(x) = 0
The auxillary equation is
3m2 + 27 = 0
m2 + 9 = 0
m = 3i
Solution is y = c1 cos 3x + c2 sin 3x
given that y(0) = 0
0 = c1
y = 3c1 sin 3x + 3c2 cos 3x
y (0) = 2000
2000 = 0 + 3c2
2000
c2 =
3
2000
Solution is y = sin3 x
3
2000
when x = 1 y= sin3 = 34.89
3
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 16
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.36 The volume and temperature of air (assumed to be an ideal gas) in a closed vessel
is 2.87 m3 and 300 K, respectively. The gauge pressure indicated by a manometer fitted
to the wall of the vessel is 0.5 bar. If the gas constant of air is R = 287 J/kgK and
the atmospheric pressure is 1 bar, the mass of air (in kg) in the vessel is
(a) 1.67 (b) 3.33
(c) 5.00 (d) 6.66
Ans. (c)
Ideas gas equation:
PV = mRT
Here P is absolute pressure:
P = Pabs = Pgauge + Patm = 50 + 101.325
= 151.325 kPa
PV 151.325 2.87
m= = = 5.04 kg
RT 0.287 300
Q.37 A metal ball of diameter 60 mm is initially at 220C. The ball is suddenly cooled by
an air jet of 20C. The heat transfer coefficient is 200 W/m2K. The specific heat, thermal
conductivity and density of the metal ball are 400 J/kgK, 400 W/mK and 9000 kg/m3,
respectively. The ball temperature (in C) after 90 seconds will be approximately
(a) 141 (b) 163
(c) 189 (d) 210
D = 60 mm
Ans. (a)
as at 20C
cp = 400 J/kgK R
Ti = 220C
k = 400 W/mK
= 9000 kg/m3
h = 200 w/m2 K
Time () = 90 sec
Since K being high and size of ball being small, lumped heat analysis is valid.
hA
Ti T hA Ti T
e vcp = vc = ln T T
T T p
A 3 3
Put = =
V R 30
1000
hA 3 1 1
vc = 200 90 = 0.5
p 0.03 9000 400
220 20
= e0.5 = 1.6487
T 20
T = 141.3C
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 17
GATE 2017 : Examination
Mechanical Engineering | Session-2
mm. Neglecting the gauge tolerance, the diameter (in mm, up to 3 decimal points
accuracy) of the GO ring gauge to inspect the plated pin is __________.
Ans. (29.030)
GO ring gauge will inspect maximum metal conditions i.e. UL of shaft i.e. Largest
size after platting.
m
m
02
.
25
=
L
U
tmax = 2.005 mm
Q.39 In a counter-flow heat exchanger, water is heated at the rate of 1.5 kg/s from 40C
to 80C by an oil entering at 120C and leaving at 60C. The specific heats of water
and oil are 4.2 kJ/kgK and 2 kJ/kgK, respectively. The overall heat transfer coefficient
is 400 W/m2K. The required heat transfer surface area (in m2) is
(a) 0.104 (b) 0.022
(c) 10.4 (d) 21.84
Ans. (d)
HE = Counterflow type Thi = 120C
The = 60C
Ti = 120 80 = 40C
Tce = 80C
Te = 60 40 = 20C
Tci = 40C
Ti Te 40 20
(LMTD) Counterflow = =
T 40
ln i ln
Te 20
= 28.86C
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 18
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.40 In the Rankine cycle for a steam power plant the turbine entry and exit enthalpies
are 2803 kJ/kg and 1800 kJ/kg, respectively. The enthalpies of water at pump entry
and exit are 121 kJ/kg and 124 kJ/kg respectively. The specific steam consumption
(in kg/kWh) of the cycle is _____________.
Ans. (3.6)
Given data h1 = 2803 kJ/kg 1
Q.41 The radius of gyration of a compound pendulum about the point of suspension is
100 mm. The distance between the point of suspension and the centre of mass is
250 mm. Considering the acceleration due to gravity is 9.81 m/s2, the natural
frequency (in radian/s) of the compound pendulum is _________.
Ans. (15.660)
If we displace this by an angle clockwise:
Compound pendulum
O
a
(mg a sin )
I
C.g
(m)
mg
mg
&& + a
I = 0
Here I = mk2 = m(0.1)2 (I is the MI about the point of Hinge)
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 19
GATE 2017 : Examination
Mechanical Engineering | Session-2
I = m(0.01) kg-m2
a = 250 mm = 0.250 m
g = 9.81 m/s2
m 9.81 0.250
&& +
(0.01)m = 0
&& + (245.25) = 0
1 , then
(a) a = 1, b = 1 (b) a = 1, b = 2
(c) a = 1, b = 2 (d) a = 2, b = 2
Ans. (b)
Given that the analytic function
f(2) = (x2 + ay2) + i bxy
u + i v = (x2 + ay2) + i (bxy)
u = x2 + ay 2; v = bxy
ux = 2x; uy = 2ay ; vx = by ; vy = bx
ux = vy; uy = vx
2x = bx; 2ay = by
b = 2; 2a = b since b = 2
2a = 2
a= 1
50 70
Q.43 Consider the matrix A = whose eigenvectors corresponding to eigenvalues
70 80
70 1 80
1 and 2 are x1 =
50 and x2 = , respectively. The value of x1T x2 is
1 70
___________.
Ans. (0)
50 70
A=
70 80
Eigen values of A are 1, 2
1 + 2 = 130
12 = 900
70 2 80
Given that X1 = X2 =
1 50 70
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 20
GATE 2017 : Examination
Mechanical Engineering | Session-2
2 80
X1T X2 = [70 1 50]
70
= 70 2 5600 + 70 1 3500
= 70 (1 + 2) 9100 = 70 (130) 9100
= 9100 9100 = 0
Q.44 The arrangement shown in the figure measures the velocity V of a gas of density 1 kg/m3
flowing through a pipe. The acceleration due to gravity is 9.81 m/s2. If the manometric
fluid is water (density 1000 kg/m3) and the velocity V is 20 m/s, the differential head
h (in mm) between the two arms of the manometer is ________.
Water
Ans. (20.38)
Method : (i)
Given data: gas = 1 kg/m3; g = 9.81 m/s2, m = 1000 kg/m3, V = 20 m/s
Dynamic pressure of gas = (gh)water
1
V 2 = m 9.81 h
2 gas
1
1 (20)2 = 1000 9.81 h
2
or h = 0.02038 m of water
= 20.38 mm of water
Method : (ii)
m = 1000 kg/m3, w = 1 kg/m3
V = 20 m/s
V= 2gh m 1
w
1000
20 = 2 9.81 h 1
1
h = 20.40 mm of water
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 21
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.45 The surface integral F ndS over the surface S of the sphere x 2 + y 2 + z 2 = 9 , where
s
F = (x + y)i + (x + z)j + (y + z) k and n is the unit outward surface normal, yields
____________.
Ans. (226.08)
F = (x + y)i + (x + z)j + (y + z) k
F= ( x + y ) + ( x + z ) + (y + z )
x y z
=1 + 0 + 1 = 2
By Gauss divergence theorem
F ndS
= F dV = 2 dV
s v v
= 2V where V is volume of x 2 + y 2 + z 2
4
= 2 (3)3 = 226.08
3
Q.46 A gear train shown in the figure consists of gears P, Q, R and S. Gear Q and gear
R are mounted on the same shaft. All the gears are mounted on parallel shafts and
the number of teeth of P, Q, R and S are 24, 45, 30 and 80, respectively. Gear P
is rotating at 400 rpm. The speed (in rpm) of the gear S is _________.
S
Q
P R
24 30
45
80
Ans. (120)
TP = 24
TQ = 45 NP = 400 rpm
TR = 30 NS = ?
TS = 80
Here gear R is not mashing at all.
NP T 45
= Q = ...(1)
NQ TP 24
NQ TS 80
= T = 45 ...(2)
NS Q
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 22
GATE 2017 : Examination
Mechanical Engineering | Session-2
By (1) (2)
NP 45 80
NS = 24 45
24 400 24
NS = NP =
80 80
NS = 120 r.p.m
Ans. (40)
Max. Z = 5x1 + 3x2 + 0 S1 + 0 S2
x1 + 2x1 + S1 = 10
x 1 x 2 + S2 = 8
x1 x2 S1 S2 bi i = bi /aij
ei 2 1 0 10 10
0 S1 1
Key Row
0 S2 (1)* 1 0 1 8 8
Cj 5 3 0 0
Objective function
Zj 0 0 0 0 will increase by ` 5
j 5 3 0 0 per unit of x1 and
bring 8 units.
Key column So, total increase (18 5 = ` 40)
Q.48 A steel plate, connected to a fixed channel using three identical bolts A, B and C,
carries a load of 6 kN as shown in the figure. Considering the effect of direct load
and moment, the magnitude of resultant shear force (in kN) on bolt C is
Channel
Steel plate
A B C
6 kN
30 50 50 30 170
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 23
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (c)
P P
PP = = = 2 kN
n 3
r A = rC = 50; (PS)A = (PS)C
r B = 0 (PS)B = 0 (PS)A
rA rC
(PS )C 2
rC + rB2 + rA2 = P e A C
rC
B
50 50 (Ps)c
PP P = 6 kN
( PS ) C 2 r C = P e PP
(PP) e = 250
6 250
( PS )C = = 15 kN
2 50
A = 180; C = 0
Resultant shear force (RC) = PP + (PS)C [ C = 0]
RC = 2 + 15 = 17 kN
RA = (PS)A PP = 13 kN
RB = PP = 2 kN
Q.49 During the turning of a 20 mm diameter steel bar at a spindle speed of 400 rpm,
a tool life of 20 minute is obtained. When the same bar is turned at 200 rpm, the
tool life becomes 60 minute. Assume that Taylors tool life equation is valid. When
the bar is turned at 300 rpm, the tool life (in minute) is approximately
(a) 25 (b) 32
(c) 40 (d) 50
Ans. (b)
V1 = D 400 m/min; T1 = 20 min
V2 = D 200 m/min; T2 = 60 min
Now using Taylors equation
V 1 T 1 n = V 2 T 2n
or D 400 (20)n = D 200 60n
or n = 0.6309
and V3 = D 300 m/min; T3 = ?
V1T1n = V2T2n = V3T3n
D 400 (20)0.6309 = D 300 T30.6309
T3 = 31.55 min 32 min
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 24
GATE 2017 : Examination
Mechanical Engineering | Session-2
Plate
D1 = 6 cm
D2 = 4 cm
20 m/s
20 m/s
Ans. (628.32)
= 1000 kg/m3
Force, F = momentuminlet momentumoutlet
F = (mv
& ) (mv
in
& )
out
2 2
F = (D1 D2 ) V = 1000 [0.06 0.04 ] 20
2 2 2 2
4 4
= 628.32 N
Q.51 The principal stresses at a point in a critical section of a machine component are
1 = 60 MPa, 2 = 5 MPa and 3 = 40 MPa. For the material of the component,
the tensile yield strength is y = 200 MPa. According to the maximum shear stress
theory, the factor of safety is
(a) 1.67 (b) 2.00
(c) 3.60 (d) 4.00
Ans. (b)
As per max. shear stress theory,
safe condition for design,
SYS SYt
Absolute max = or
N 2N
1 2 2 3 3 1
Absolute max = larger of , ,
2 2 2
3 1
= [ 1 and 3 are unlike in nature]
2
40 60
= = 50 MPa
2
200
Hence, 50 =
2(N )
N=2
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 25
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.52 A single-plate clutch has a friction disc with inner and outer radii of 20 mm and
40 mm, respectively. The friction lining in the disc is made in such a way that the
coefficient of friction varies radially as = 0.01 r, where r is in mm. The clutch
needs to transmit a friction torque of 18.85 kN mm. As per uniform pressure theory,
the pressure (in MPa) on the disc is __________.
Ans. (0.5)
r dr
dA = 2r(dr )
Normal load on elemental ring (dW) = p2rdr
Frictional force on elemental ring (dFf ) = dW
Frictional torque transmitted by elemental ring, elemental
ring (dA)
dTf = (dFf)r
Hence, dTf = p2r2dr Ri
R0 Ro
Total frictional torque transmitted by clutch plate (Tf) = R i
dTf
Clutch plate
R0 2
Tf = R i
p2 r dr
R0
As per U.P.T. Tf = 2p r 2dr
Ri
R0
2
Tf = 2p R (0.01r )r dr
i
R 4 Ri4
(Tf )U.P.T. = (2p)(0.01) 0
4
404 204
18.85 103 = 2p(0.01)
4
p = 0.5 MPa
Q.53 A product made in two factories, P and Q, is transported to two destinations, R and
S. The per unit costs of transportation (in Rupees) from factories to destinations are
as per the following matrix:
Destination
R S
Factory
P 10 7
Q 3 4
Factory P produces 7 units and factory Q produces 9 units of the product. Each
destination requires 8 units. If the north-west corner method provides the total
transportation cost X (in Rupees) and the optimized (the minimum) total transportation
cost is Y (in Rupees), then(X Y ), in Rupees, is
(a) 0 (b) 15
(c) 35 (d) 105
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 26
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (*)
X = 105
Using penalty corner method and following modi method we get
R S
Penalty
10 7 7 3 0
P 7
4
5 4
Q 3 1 9 1 3
8 8
Penalty 7 3
vj 6 7
4 water value indicates that its optimum table, so
Y = 7 7 + 3 8 + 4 = 49 + 24 + 4 = 78
X Y = 105 77 = 28
Q.54 One kg of an ideal gas (gas constant R = 287 J/kgK) undergoes an irreversible
process from state-1 (1 bar, 300 K) to state-2 (2 bar, 300 K). The change in specific
entropy (s2 s1) of the gas (in J/kgK) in the process is __________.
Ans. (198.93)
Change in specific entropy of ideal gas
Tf P
sf si = cp ln R ln f
Ti Pi
300 2
= 1005ln 287ln
300 1
= 0 287 ln2 = 198.93 J/kg-K
Q.55 A project starts with activity A and ends with activity F. The precedence relation and
durations of the activities are as per the following table:
Activity Immediate predecessor Duration (days)
A 4
B A 3
C A 7
D B 14
E C 4
F D, E 9
Ans. (30)
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 27
GATE 2017 : Examination
Mechanical Engineering | Session-2
3 D,
B, 3 14
A, 4 F, 9
1 2 5 6
C, 7
E, 4
4
GENERAL APTITUDE
Q.1 If a and b are integers and a b is even, which of the following must always be
even?
(a) ab (b) a 2 + b 2 + 1
(c) a2 + b + 1 (d) ab b
Ans. (d)
Q.2 The ways in which this game can be played __________ potentially infinite.
(a) is (b) is being
(c) are (d) are being
Ans. (a)
Q.3 If you choose plan P, you will have to ______ plan Q, as these two are mutually _____.
(a) forgo, exclusive (b) forget, inclusive
(c) accept, exhaustive (d) adopt, intrusive
Ans. (a)
Q.4 P looks at Q while Q looks at R, P is married, R is not. The number of pairs of people
in which a married person is looking at an unmarried person is
(a) 0 (b) 1
(c) 2 (d) cannot be determined
Ans. (d)
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 28
GATE 2017 : Examination
Mechanical Engineering | Session-2
Q.5 A couple has 2 children. The probability that both children are boys if the older one
is a boy is
(a) 1/4 (b) 1/3
(c) 1/2 (d) 1
Ans. (c)
Q.6 All people in a certain island are either Knights or Knaves and each person knows
every other persons identity. Knights NEVER lie, and knaves ALWAYS lie.
P says Both of us are knight. Q says None of us are knaves
Which one of the following can be logically inferred from the above?
(a) Both P and Q are knights (b) P is a knight; Q is a knave
(c) Both P and Q are knaves (d) The identities of P, Q cannot be determined
Ans. (d)
Ans. (c)
Q.8 In the graph below, the concentration of a particular pollutant in a lake is plotted over
(alternate) days of a month in winter (average temperature 10C) and a month in
summer (average temperature 30C)
11
10 Winter
Pollutant Concentration (ppm)
9 Summer
8
7
6
5
4
3
2
1
0
0 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
Day of the month
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 |
info@madeeasy.in | www.madeeasy.in Page 29
GATE 2017 : Examination
Mechanical Engineering | Session-2
Ans. (b)
Q.9 X bullocks and Y tractors take 8 days to plough a field. If we halve the number of
bullocks and double the number of tractors, it takes 5 days to plough the same field.
How many days will it take X bullocks alone to plough the field?
(a) 30 (b) 35
(c) 40 (d) 45
Ans. (a)
Q.10 If you are looking for a history of India, or for an account of the rise and fall of the
British Raj, or for the reason of the cleaving of the subcontinent into two mutually
antagonistic parts and the effects this mutilation will have in the respective sections,
and ultimately on Asia, you will not find it in these pages; for though I have spent
a lifetime in the country, I lived too near the seat of events, and was too intimately
associated with the actors, to get the perspective needed for the impartial recording
of these matters.
Which of the following is closest in meaning to cleaving?
(a) deteriorating (b) arguing
(c) departing (d) splitting
Ans. (d)
Corporate Office: 44-A/1, Kalu Sarai, New Delhi-110016 | info@madeeasy.in | www.madeeasy.in Page 30