Professional Documents
Culture Documents
Features:
- suitable for the tension zone
- high loading capacity
- force-controlled expansion
- reliable pull-down of part fastened
- no rotation in hole when tightening bolt HSL-3
Bolt Material:
- grade 8.8 acc. DIN EN ISO 898-1
galvanised to min. 5 microns
Versions:
HSL-3 - bolt HSL-3-G
HSL-3-G - nut
HSL-3-B - safety cap (automatic torque control)
HSL-3-SK - countersunk head
HSL-3-SH - socket head
HSL-3-B
Concrete
Tensile Fire Hilti Anchor
Close edge
distance/
HSL-3-SK
zone resistance Programme
spacing
Basic loading data (for a single anchor): HSL-3 / HSL-3-B / HSL-3-SH*/ HSL-3-SK*
All data on this page applies to For detailed design method, see pages 56 60.
concrete: as specified in the table
no edge distance and spacing influence
correct setting (See setting operations page 56)
steel failure
Anchor size M8 M10 M12 M16 M20 M24 M8 M10 M12 M16 M20 M24
Tensile NRu,m 28.4 37.7 53.4 71.3 100.6 133.1 20.3 26.9 38.1 50.9 71.8 95.0
Shear VRu,m 43.0 63.5 88.9 128.6 160.6 239.7 43.0 63.5 88.9 128.6 160.6 239.7
Anchor size M8 M10 M12 M16 M20 M24 M8 M10 M12 M16 M20 M24
Tensile NRk 23.4 29.5 36.1 50.4 70.4 92.6 16.7 21.1 25.8 36.0 50.3 66.1
Shear VRk 31.1 49.2 71.7 101.1 141.9 177.4 31.1 49.2 71.7 101.1 141.9 177.4
52
HSL-3 heavy duty anchor
Anchor size M8 M10 M12 M16 M20 M24 M8 M10 M12 M16 M20 M24
Tensile NRd 15.6 19.7 24.1 33.6 46.9 61.7 6.7 10.7 17.2 24.0 33.5 44.1
Shear VRd 24.9 39.4 57.4 80.9 113.5 141.9 24.9 39.4 57.4 80.9 113.5 141.9
Anchor size M8 M10 M12 M16 M20 M24 M8 M10 M12 M16 M20 M24
Tensile NRec 11.1 14.0 17.2 24.0 33.5 44.1 4.8 7.6 12.3 17.1 24.0 31.5
Shear VRec 17.8 28.1 41.0 57.8 81.1 101.4 17.8 28.1 41.0 57.8 81.1 101.4
Anchor size M8 M10 M12 M16 M20 M8 M10 M12 M16 M20
Tensile NRk 23.4 29.5 36.1 50.4 70.4 16.7 21.1 25.8 36.0 50.3
Shear VRk 26.1 34.8 54.3 85.7 141.9 26.1 34.8 54.3 85.7 141.9
Anchor size M8 M10 M12 M16 M20 M8 M10 M12 M16 M20
Tensile NRd 15.6 19.7 24.1 33.6 46.9 6.7 10.7 17.2 24.0 33.5
Shear VRd 20.9 27.8 43.4 68.6 113.5 20.9 27.8 43.4 68.6 113.5
Anchor size M8 M10 M12 M16 M20 M8 M10 M12 M16 M20
Tensile NRec 11.1 14.0 17.2 24.0 33.5 4.8 7.6 12.3 17.1 24.0
Shear VRec 14.9 19.9 31.0 49.0 81.1 14.9 19.9 31.0 49.0 81.1
Installation equipment
Rotary hammer (TE1, TE2, TE5, TE6, TE6A, TE15, TE15-C, TE18-M, TE35, TE55, TE76), hammer, torque
wrench, blow out pump.
53
HSL-3 heavy duty anchor
Setting details
HSL-3
Anchor size M8/ tfix M10/ tfix M12/ tfix M16/ tfix M20/ tfix M24/ tfix
tfix [mm] Fastenable thickness (small/medium/large)
1)
5/20/40 5/20/40 5/25/50 10/25/50 10/30/60 10/30/60
d0 [mm] Nominal diameter of drill hole 12 15 18 24 28 32
[mm] Diameter of drill bit 12.5 15.5 18.5 24.55 28.55 32.7
h1 [mm] Depth of drill hole 80 90 105 125 155 180
hef [mm] Effective anchorage depth 60 70 80 100 125 150
2)
l [mm] Anchor length
tfix small 83 95 111 138 163 185
tfix medium 98 110 131 153 183 205
tfix large 118 130 156 178 213 235
[mm] Head height and washer 7.5 10 11 14 17 19
dw [mm] Washer diameter 20 25 30 40 45 50
hmin [mm] Min. base material thickness 120 140 160 200 250 300
df [mm] Clearance hole 14 17 20 26 31 35
SW [mm] Width across 13 17 19 24 30 36
Tinst [Nm] Torque moment 25 50 80 120 200 250
HSL-3-SH
HSL-3-SK
56
HSL-3 heavy duty anchor
HSL-3-G
M8/ tfix M10/ tfix M12/ tfix M16/ tfix M20/ tfix
Anchor size
1)
tfix [mm] Fastenable thickness (small/medium/large/ 100 mm) 5/20/40/ 5/20/40/ 5/25/50/ 10/25/50/ 10/30/60/1
100 100 100 100 00
d0 [mm] Nominal diameter of drill hole 12 15 18 24 28
[mm] Diameter of drill bit 12,5 15,5 18,5 24,55 28,55
h1 [mm] Depth of drill hole 80 90 105 125 155
hef [mm] Effective anchorage depth 60 70 80 100 125
2)
l [mm] Anchor length
tfix small 87 100 119 148 170
tfix medium 102 115 139 163 190
tfix large 122 135 164 188 220
tfix = 100 mm 182 195 214 238 260
[mm] Head height and washer 8 11 13 17 20
dw [mm] Washer diameter 20 25 30 40 45
hmin [mm] Min. base material thickness 120 140 160 200 250
df [mm] Clearance hole (through setting) 14 17 20 26 31
df [mm] Clearance hole (only threaded rod carries the load) 9 12 14 18 22
SW [mm] Width across 13 17 19 24 30
Tinst [Nm] Torque moment 20 35 60 80 160
1)
Other tfix possible
2)
Other anchor length possible
according to other tfix
56
HSL-3 heavy duty anchor
HSL-3-B
Anchor size M12/ tfix M16/ tfix M20/ tfix M24/ tfix
1)
tfix [mm] ( small / medium / large) 5/25/50 10/25/50 10/30/60 10/30/60
1)
Other tfix possible
2)
Other anchor length possible
according to other tfix
Tinst.
hef tfix
h1
hmin
56
HSL-3 heavy duty anchor
Setting operations
1 2 3 4
Drill hole. Blow out dust and fragments. Install anchor. Apply tightening torque
(for HSL-3-B: no torque wrench is
needed)
2
fuk [N/mm ] Nominal tensile strength 800 800 800 800 830 830
2
fyk [N/mm ] Yield strength 8.8 640 640 640 640 640 640
2
As [mm ] Stressed crossed-section 36.6 58.0 84.3 157.0 245.0 353.0
2
W [mm ] Elastic moment of resistance 30 60 105 266 519 898
Mrec [Nm] Recommended bending moment without sleeve 12.5 24.9 43.7 111.0 216.4 374.2
TENSION s
c
The tensile design resistance of a single anchor
h
57
HSL-3 heavy duty anchor
NRd,c : Concrete cone resistance
o
NRd,c = NRd,c f B f A,N fR,N
60
HSL-3 heavy duty anchor
fRN: Influence of edge distance
Minimum thickness of concrete member, minimum spacing and minimum edge distance of anchors in cracked
and uncracked concrete
Combined loading: Only if tensile load and shear load applied (See page 31 and section 4 Examples).
c2 > V rec,c/s
SHEAR 1.5
c
s
The design shear resistance of a single anchor c c2 >
1.5
is the lower of, c
h>
1.5
VRd,c : concrete edge resistance c
VRd,s : steel resistance Note: If the conditions for
h and c2 are not met, consult your
Hilti technical advisory. service.
60
HSL-3 heavy duty anchor
VRd,c : Concrete edge design resistance
The lowest concrete edge resistance must be calculated. All nearby edges must be checked, (not only the
edge in the direction of shear). Shear direction is accounted for by the factor f,V.
o
VRd,c = VRd,c f B f ,V f AR,V
c c s3
f AR,V = s2
c min c min s1
results
c 2 ,2 c
Formula for two-anchor fastening valid for s < 3c
tabulated
below
3c + s c
f AR,V = h >1,5 c
6c min c min
60
HSL-3 heavy duty anchor
3c + s1 + s 2 + ... + s n 1 c
f AR ,V =
3nc min c min
Note : It is assumed that only the row of anchors closest to the free concrete edge carries the centric shear load
c/cmin
fAR.V
1.0 1.2 1.4 1.6 1.8 2.0 2.2 2.4 2.6 2.8 3.0 3.2 3.4 3.6 3.8 4.0
Single anchor with
edge influence 1.00 1.31 1.66 2.02 2.41 2.83 3.26 3.72 4.19 4.69 5.20 5.72 6.27 6.83 7.41 8.00
s/cmin 1.0 0.67 0.84 1.03 1.22 1.43 1.65 1.88 2.12 2.36 2.62 2.89 3.16 3.44 3.73 4.03 4.33
1.5 0.75 0.93 1.12 1.33 1.54 1.77 2.00 2.25 2.50 2.76 3.03 3.31 3.60 3.89 4.19 4.50
2.0 0.83 1.02 1.22 1.43 1.65 1.89 2.13 2.38 2.63 2.90 3.18 3.46 3.75 4.05 4.35 4.67
2.5 0.92 1.11 1.32 1.54 1.77 2.00 2.25 2.50 2.77 3.04 3.32 3.61 3.90 4.21 4.52 4.83
3.0 1.00 1.20 1.42 1.64 1.88 2.12 2.37 2.63 2.90 3.18 3.46 3.76 4.06 4.36 4.68 5.00
3.5 1.30 1.52 1.75 1.99 2.24 2.50 2.76 3.04 3.32 3.61 3.91 4.21 4.52 4.84 5.17
4.0 1.62 1.86 2.10 2.36 2.62 2.89 3.17 3.46 3.75 4.05 4.36 4.68 5.00 5.33
4.5 1.96 2.21 2.47 2.74 3.02 3.31 3.60 3.90 4.20 4.52 4.84 5.17 5.50
5.0 2.33 2.59 2.87 3.15 3.44 3.74 4.04 4.35 4.67 5.00 5.33 5.67
5.5 2.71 2.99 3.28 3.57 3.88 4.19 4.50 4.82 5.15 5.49 5.83
6.0 2.83 3.11 3.41 3.71 4.02 4.33 4.65 4.98 5.31 5.65 6.00
6.5 3.24 3.54 3.84 4.16 4.47 4.80 5.13 5.47 5.82 6.17
7.0 3.67 3.98 4.29 4.62 4.95 5.29 5.63 5.98 6.33
7.5 4.11 4.43 4.76 5.10 5.44 5.79 6.14 6.50
8.0 4.57 4.91 5.25 5.59 5.95 6.30 6.67
8.5 These results are for a two-. 5.05 5.40 5.75 6.10 6.47 6.83
9.0 Anchor fastening. 5.20 5.55 5.90 6.26 6.63 7.00
9.5 5.69 6.05 6.42 6.79 7.17
10.0 For fastening made with more 6.21 6.58 6.95 7.33
10.5 than 2 anchors, use the 6.74 7.12 7.50
11.0 general formulae for n 7.28 7.67
11.5 anchors at the top of the page. 7.83
12.0 8.00
The shear design resistance is calculated from the shear characteristic resistance VRd,s by VRd,s= VRk,s/Ms, where the partial
safety factor Ms is 1.25.
Combined loading: Only if tensile load and shear load applied (See page 31 and section 4 Examples).
61
HSL-3 heavy duty anchor
61
HSL-3 heavy duty anchor
The shear design resistance is calculated from the shear characteristic resistance VRd,s by VRd,s= VRk,s/Ms, where the partial
safety factor Ms is 1.25.
Combined loading: Only if tensile load and shear load applied (See page 31 and section 4 Examples).
61