Professional Documents
Culture Documents
SERVICE MANUAL
SECIFICATION
VHF-H S7-S41
UHF E21- E69
SPEAKER 3W 8OHM
SAFETY PRECAUTION
WARNING: Service should not be attempted by anyone unfamiliar with the necessary
Precautions on this receiver.
The following are the necessary precautions to be observed before servicing this chassis.
1. Since the power supply circuit of this receiver is directly connected to the AC power line. An
isolation transformer should be used during any dynamic service to avoid possible shock hazard.
2. Always discharge the picture tube anode to the CRT conductive coating before handling the
picture tube. The picture tube is highly evacuated and if broken, glass fragments will be violently
expelled. Use shatterproof goggles and keep picture tube away from the unprotected body while
handling.
3. When replacing a chassis in the cabinet, always be certain that all the protective devices are put
back in place, such as: nonmetallic control; knobs, insulating covers, shields, isolation
resistor-capacitor, network, etc.
4. When replacing parts or circuit boards, disconnect the power cord.
5. When replacing a high voltage resistor (metal oxide resistor) on circuit hoard, keep the resistor
APP. 10mm(1/2 in.) away from circuit board.
6. Connection wires must be kept away from components with high voltage or high temperature.
7. If any fuse in this TV receiver is blown, replace it with the FUSE specified in the chassis parts
list.
8. The receiver is designed to operate with 230V(50Hz) AC mains.
2
PRODUCT SAFETY NOTICE
Many electrical and mechanical parts in this chassis have special safety-related characteristics are
often passed unnoticed by a visual inspection and the X-RAY RADIATON protection afforded by
them cannot necessarily be obtained by using replacement components rated for higher voltage.
The use of substitute replacement parts that do not have the same safety characteristics as
specified in the parts list may create shock, fire, X-RAY RADIATION or other hazards.
GENERAL ADJUSTMENT
AUTOMATIC DEGAUSSING
An automatic degaussing coil is attached around the picture tube, degaussing the tube properly in
about one second after the set is switched on. If the receiver is moved or faced on a different
direction, the power must be switched off at least 15 minutes in order that the automatic
degaussing circuit operated properly. External degaussing is necessary if the automatic degassing
proves ineffective after the set is moved.
B+ ADJUSTMENT
CAUTION: To avoid X-ray hazards and result in a nominal display width, B+ voltage must be set in
the scale of 110.0V+/-0.5V.
1. Make sure the AC power supply is 230V, 50Hz.
2. Switch on the TV receiver, tune in an active channel.
3. Measure the voltage between C318 on Main P.C. Board by DC voltmeter.
4. Set contrast, brightness, color to maximum.
5. Adjust RP301 on Main P. C. Board for B+110.0V+/-0.5V voltage reading.
3
HIGH VOLTAGE CHECK
CAUTION: There is no high voltage adjustment in this chassis, B+110V voltage directly relates to
the high voltage. The high voltage does not exceed 27KV under any conditions.
1. Connect an accurate high voltage meter to the second anode cap of the picture tube.
2. Turn on the receiver, set brightness and contrast to minimum (Zero beam current).
3. Make sure the high voltage does not exceed 27KV.
4. NO matter whether the luminance, contrast and chrominance controls are set to maximum or
minimum, the high voltage must be kept under 27KV.
FOCUSING
Receive a TV test pattern signal; adjust controls for optimum picture. Adjust Focus Control for a
well-defined, sharpest display in the center area of the screen.
SERVICE MODE
To enter the service mode, short service mode points on PCB (X202, pins 1&2) or press from
ST-BY mode STATUS>MENU>MUTE>ST-BY on RC.
TV will display service menu as following table 1 line by line. To select the parameter by using the
P+/P- keys. To adjust the selected parameter by using the V+/V- keys. To quit the service mode,
press the TV key on remote control when in the service mode.
Table 1
SERVICE MODE (enter: to short service mode points or press from ST-BY mode
STATUS>MENU>MUTE>ST-BY)
Control bits Function Value Notes
HS Horizontal Shift 31
VHS Vertical Shift 30
VA Vertical Amplitude 30
VAZ Vertical expand (zoom) 1 VX
VS Vertical Slope 33
SC S-Correction 22
CL Cathode drive Level 7 50 .. 95 Volt drive
Y Y Delay 7
IFO IF PLL Offset adjusment 32
Vg2 Screen Voltage Alignment mode OK Screen VR (on the FBT)
Brightness control setting in sreen
Vg2BR 32
voltage alignment mode
4
BLOR Black level off-set R 32
BLOG Black level off-set G 32
R White point R 32
G White point G 32
B White point B 32
AGC AGC Take Over Point 35 TOP
BCF Black Current loop Failure 0
OSO Overscan Switch-Off 1
AGN Sound pre-amplifier +6 db 1 Gain FM demodulator
IE2 RGB Insertion Enable 1
ACL Automatic Colour Limiting 1
For special conditions (descramblers with
unstable black level) the vertical slicing
FSL forced vertical slicing level 0 level can be forced to 70% under all
conditions by setting FSL = 1.
5
IC DESCRIPTIONS AND INTERNAL BLOCK DIAGRAM
TDA9351
STV9302
TDA7056A
24C08W6
74HC4053
UC3842
TDA9351:
The various versions of the TDA935X/6X/8XPS/N2 series combine the functions of a TV signal
processor together with a -Controller and US Closed Caption decoder. Most versions have a
Teletext decoder on board. The Teletext decoder has an internal RAM memory for 1 or 10 page
text. The ICs are intended to be used in economy television receivers with 90 and 110 picture
tubes.
The ICs have supply voltages of 8 V and 3.3 V and they are mounted in S-DIP envelope with 64
pins.
Features:
TV-signal processor
Multi-standard vision IF circuit with alignment-free PLL demodulator.
Internal (switchable) time-constant for the IF-AGC circuit.
A choice can be made between versions with mono intercarrier sound FM demodulator and
versions with QSS IF amplifier.
The mono intercarrier sound versions have a selective FM-PLL demodulator which can be
switched to the different FM sound frequencies (4.5/5.5/6.0/6.5 MHz). The quality of this system is
such that the external band-pass filters can be omitted.
Source selection between internal CVBS and external CVBS or Y/C signals.
Integrated chrominance trap circuit.
Integrated luminance delay line with adjustable delay time.
Picture improvement features with peaking (with variable centre frequency and positive/negative
overshoot ratio) and black stretching.
Integrated chroma band-pass filter with switchable centre frequency.
Only one reference (12 MHz) crystal required for the -Controller, Teletext- and the colour
decoder.
PAL/NTSC or multi-standard colour decoder with automatic search system.
Internal base-band delay line.
RGB control circuit with Continuous Cathode Calibration, white point and black level offset
adjustment so that the colour temperature of the dark and the light parts of the screen can be
chosen independently.
Linear RGB or YUV input with fast blanking for external RGB/YUV sources. The Text/OSD
signals are internally supplied from the -Controller/Teletext decoder.
Contrast reduction possibility during mixed-mode of OSD and Text signals.
6
Horizontal synchronization with two control loops and alignment-free horizontal oscillator.
Vertical count-down circuit.
Vertical driver optimized for DC-coupled vertical output stages.
Horizontal and vertical geometry processing.
Horizontal and vertical zoom function for 16:9 applications.
Horizontal parallelogram and bow correction for large screen picture tubes.
Low-power start-up of the horizontal drive circuit.
-Controller
80C51-controller core standard instruction set and timing.
1s machine cycle.
32 - 128Kx8-bit late programmed ROM.
3 - 12Kx8-bit Auxiliary RAM (shared with Display and Acquisition).
Interrupt controller for individual enable/disable with two level priority.
Two 16-bit Timer/Counter registers.
One 16 bit Timer with 8-bit Pre-scaler.
WatchDog timer.
Auxiliary RAM page pointer.
16-bit Data pointer.
Stand-by, Idle and Power Down (PD) mode.
14 bits PWM for Voltage Synthesis Tuning.
8-bit A/D converter.
4 pins which can be programmed as general I/O pin, ADC input or PWM (6-bit) output.
Data Capture
Text memory for 0, 1 or 10 pages.
In the 10 page versions inventory of transmitted Teletext pages stored in the Transmitted Page
Table (TPT) and Subtitle Page Table (SPT).
Data Capture for US Closed Caption.
Data Capture for 525/625 line WST, VPS (PDC system A) and Wide Screen Signalling (WSS) bit
decoding.
Automatic selection between 525 WST/625 WST.
Automatic selection between 625 WST/VPS on line 16 of VBI.
Real-time capture and decoding for WST Teletext in Hardware, to enable optimized-processor
throughput.
Automatic detection of FASTEXT transmission.
Real-time packet 26 engine in Hardware for processing accented, G2 and G3 characters.
Signal quality detector for video and WST/VPS data types.
Comprehensive teletext language coverage.
Full Field and Vertical Blanking Interval (VBI) data capture of WST data.
Display
Teletext and Enhanced OSD modes.
Features of level 1.5 WST and US Close Caption.
7
Serial and Parallel Display Attributes.
Single/Double/Quadruple Width and Height for characters.
Scrolling of display region.
Variable flash rate controlled by software.
Enhanced display features including overlining, underlining and italics.
Soft colours using CLUT with 4096 colour palette.
Globally selectable scanlines per row (9/10/13/16) and character matrix [12x10, 12x13, 12x16
(VxH)].
Fringing (Shadow) selectable from N-S-E-W direction.
Fringe colour selectable.
Meshing of defined area.
Contrast reduction of defined area.
Cursor.
Special Graphics Characters with two planes, allowing our colours per character.
32 software redefinable On-Screen display characters.
4 WST Character sets (G0/G2) in single device (e.g. Latin, Cyrillic, Greek, Arabic).
G1 Mosaic graphics, Limited G3 Line drawing characters.
WST Character sets and Closed Caption Character set in single device.
PINNING
SYMBOL PIN DESCRIPTION
P1.3/T1 1 port 1.3 or Counter/Timer 1 input
P1.6/SCL 2 port 1.6 or I2C-bus clock line
P1.7/SDA 3 port 1.7 or I2C-bus data line
P2.0/TPWM 4 port 2.0 or Tuning PWM output
P3.0/ADC0 5 port 3.0 or ADC0 input
P3.1/ADC1 6 port 3.1 or ADC1 input
P3.2/ADC2 7 port 3.2 or ADC2 input
P3.3/ADC3 8 port 3.3 or ADC3 input
VSSC/P 9 digital ground for -Controller core and periphery
port 0.5 (8 mA current sinking capability for direct drive of
P0.5 10
LEDs)
port 0.6 (8 mA current sinking capability for direct drive of
P0.6 11
LEDs)
analog ground of Teletext decoder and digital ground of
VSSA 12
TV-processor
SECPLL 13 SECAM PLL decoupling
VP2 14 2nd supply voltage TV-processor (+8V)
DECDIG 15 decoupling digital supply of TV-processor
PH2LF 16 phase-2 filter
PH1LF 17 phase-1 filter
GND3 18 ground 3 for TV-processor
DECBG 19 bandgap decoupling
AVL/EWD 20 Automatic Volume Levelling /East-West drive output
VDRB 21 vertical drive B output
VDRA 22 vertical drive A output
IFIN1 23 IF input 1
IFIN2 24 IF input 2
IREF 25 reference current input
VSC 26 vertical sawtooth capacitor
8
TUNERAGC 27 tuner AGC output
AUDEEM/SIFIN1 28 audio deemphasis or SIF input 1
DECSDEM/SIFIN2 29 decoupling sound demodulator or SIF input 2
GND2 30 ground 2 for TV processor
SNDPLL/SIFAGC 31 narrow band PLL filter /AGC sound IF
Automatic Volume Levelling/sound IF input/subcarrier
AVL/SNDIF/REF0/ AMOUT 32
reference output/AM output (non controlled)
HOUT 33 horizontal output
FBISO output 34 flyback input/sandcastle
external audio input/QSS intercarrier out/AM audio output
AUDEXT/QSSO/AMOUT 35
(non controlled)
EHTO 36 EHT/overvoltage protection input
PLLIF 37 IF-PLL loop filter
IFVO/SVO 38 IF video output/selected CVBS output
VP1 39 main supply voltageTV-processor (+8V)
CVBSINT 40 internal CVBS input
GND1 41 ground 1 for TV-processor
CVBS/Y 42 external CVBS/Y input
CHROMA 43 chrominance input (SVHS)
AUDOUT/AMOUT 44 audio output/AM audio output (volume controlled)
INSSW2 45 2nd RGB/YUV insertion input
R2/VIN 46 2nd R input / V (R-Y) input
G2/YIN 47 2nd G input / Y input
B2/UIN 48 2nd B input / U (B-Y) input
BCLIN 49 beam current limiter input / (V-guard input)
BLKIN 50 black current input / (V-guard input)
RO 51 Red output
GO 52 Green output
BO 53 Blue output
analog supply of Teletext decoder and digital supply of
VDDA 54
TV-processor (3.3 V)
VPE 55 OTP Programming Voltage
VDDC 56 digital supply to core (3.3 V)
OSCGND 57 oscillator ground supply
XTALIN 58 crystal oscillator input
XTALOUT 59 crystal oscillator output
RESET 60 reset
VDDP 61 digital supply to periphery (+3.3 V)
P1.0/INT1 62 port 1.0 or external interrupt 1 input
P1.1/T0 63 port 1.1 or Counter/Timer 0 input
P1.2/INT0 64 port 1.2 or external interrupt 0 input
STV9302A:
The STV9302A is a vertical deflection booster designed for TV and monitor applications. This
device, supplied with up to 35V, provides up to 2App output current to drive the vertical deflection
yoke. The internal flyback generator delivers flyback voltages up to 70V. In double-supply
applications, a stand-by state will be reached by stopping the (+) supply alone.
Features:
Power Amplifier
Flyback Generator
Output Current up to 2App
9
Thermal Protection
Stand-by Control
PINNING
1. Input (Inverting)
2. Supply Voltage
3. Flyback Generator
4. Ground Or Negative Supply
5. Output
6. Output Stage Supply
7. Input (Non Inverting)
TDA7056A:
The TDA7056A is a mono BTL output amplifier with DC volume control. It is designed for use in TV
and monitors, but also suitable for battery-fed portable recorders and radios.
Features:
DC volume control
Few external components
Mute mode
Thermal Protection
Short-circuit proof
No switch-on and off clicks
Good overall stability
Low power consumption
Low HF radiation
ESD protected on all pins.
PINNING
1. Not connected, n.c.
2. Positive supply voltage, VP
3. Voltage input, VI
4. Signal ground, GND1
5. DC volume control, VC
6. Positive output, OUT+
7. Power ground, GND2
8. Negative output, OUT-
9. Not connected, n.c.
10
24C08W6:
The M24C08W6 is a series of 2-wire, low power 8Kbit EEPROM with a wide operating range. It is
organized as 1K-word X 8-bit. It is capable of page write and sequential read.
Features:
Two Wire I2C Serial Interface Supports 400kHz Protocol.
Single Supply Voltage: 2.5V to 5.5V.
Write Control Input.
BYTE and PAGE WRITE (up to 16 Bytes).
RANDOM and SEQUENTIAL READ Modes.
Self-Timed Programming Cycle.
Automatic Address Incrementing.
Enhanced ESD/Latch-Up Behavior.
More than 1 Million Erase/Write Cycles.
More than 40 Year Data Retention.
PINNING
1. Connected to ground, A0
2. Connected to ground, A1
3. Connected to ground, A2
4. Connected to ground, A3
5. Serial data input/output, SDA
6. Serial clock input, SCL
7. Write protection Pin, WP
- Connected to VCC : Protection valid
- Connected to Ground : Protection invalid
8. Power Supply, VCC
74HC4053:
The 74HC/HCT4053 are high-speed Si-gate CMOS devices and are pin compatible with the 4053
of the 4000B series. They are specified in compliance with JEDEC standard no. 7A.
The 74HC/HCT4053 are triple 2-channel analog multiplexers/demultiplexers with a common enable
input ). Each multiplexer/demultiplexer has two independent inputs/outputs (nY0 and nY1), a
common input/output (nZ) and three digital select inputs (S1 to S3).
With LOW, one of the two switches is selected (low impedance ON-state) by S1 to S3. With
HIGH, all switches are in the high impedance OFF-state, independent of S1 to S3.
VCC and GND are the supply voltage pins for the digital control inputs (S1, to S3, and ). The VCC to
GND ranges are 2.0 to 10.0 V for HC and 4.5 to 5.5 V for HCT. The analog inputs/outputs (nY0 and
nY1, and nZ) can swing between VCC as a positive limit and Vee as a negative limit. VCC -VEE may
not exceed 10.0 V.
For operation as a digital multiplexer/demultiplexer, VEE is connected to GND (typically ground).
11
Features:
Low ON resistance:
80 (typ.) at VCC-VEE=4.5 V,
70 (typ.) at VCC-VEE=6.0 V,
60 (typ.) at VCC-VEE=9.0 V.
Logic level translation: to enable 5 V logic to communicate with 5V analog signals.
Typical break before make built in.
Output capability: non-standard.
PINNING
PIN SYMBOL NAME AND FUNCTION
2, 1 2Y0 to, 2Y1 independent inputs/outputs
5, 3 3Y0 to, 3Y1 independent inputs/outputs
6 enable input (active LOW)
7 VEE negative supply voltage
8 GND ground (0 V)
11, 10, 9 S1 to S3 select inputs
12, 13 1Y0, 1Y1 independent inputs/outputs
14, 15, 4 1Z to 3Z common inputs/outputs
16 VCC positive supply voltage
UC3842:
The UC3842 provides all the essential features necessary to the operation of the basic current
mode controller.
PINNING
1. Error amplifier output.
2. Error amplifier inverting input.
3. Current sense comparator.
4. Timing network, RT CT.
5. Device ground.
6. Switching drive output.
7. Device supply voltage input.
8. Voltage reference, 5.0V.
12
13
TV2KR PAL/SECAM, BG/I/DK, MONO CRT1 GZS10-2-104
R2 R4 R6
R1 R3 R5 R7 R
390 om 390 om 390 om 0138
15k 15k 15k
2.7k
X101
27
VT1 VT4 VT2 VT5 VT3 VT6 R8 G
0126
SCART BF422 BF422 BF422
007
R/SVHS_C
to FRONT AV BF422 BF422 BF422
25
28
A_R_OUT
A_L_OUT
2.7k
FB_GND
008
G_GND
R_GND
V_GNG
A_R_IN
V_GND
B_GND
A_GND
V_OUT
A_L_IN
R9
006
S_SW
B
X102 11
014
GND
V_IN
x3
002
N.C.
N.C.
26
FB
C126 C1 2.7k
005
009
B
24
GND
OUT
22n IC102
3
+
R10
21
20
19
18
17
16
15
14
13
12
11
10
+
HS0038A2 R12 R14 VT9
29
C12 VT8
330 om 330 om 330 om
20
L107 L110 330p BF423 4.7
R145 4.7k
BF423
3
C14
75 om
C125
30
C13
a.r.in
a.l.in
003
sw.s
105
C101
g.s
b.s
47 uH CB6A C103
r.s
10.0
fb.s
R108
R109
v.out
C105
470 om
220 om
107
+
+ 330p
21
v.csart VT7 330p
1N4148
TT8 22n
+
VD6
R103 75 om
R102 10k
L108 CB6A
75 om
100.0 47.0 BF423
2.2k
N.C.
N.C.
R106
R107 75 om
HET_
220 om
470 om
HET
R104 75 om
G1
HV
R112 220 om
G2
R111
GND
R114 75 om
F
R115
R144 4.7k
R101 004
R116
R113
33k
R105
12
10
3,3k
VD101
5.1v
TT14 5
1
117
MENU C19
TT12
C108
C107 47p 47p C110 4.7n
L112 10uH
a.s_in K101
+5st.by
C111 100p 47p
16
12
13
019
IC101 74HC4053
R121 2.7k
E_ 6
C112 L111
TT13
33k
10uH
0.33 om
0.68 om
R11
R16
R122
+
+Vcc
0_IN
1_IN
0_IN
1_IN
0_IN
1_IN
R15
118
47.0 C114 47p -
560 om R117
+8a
100 om
CRT BOARD
R120
001
SCREEN
TT7
GND
OUT
OUT
OUT
L102
Vee
VD102
HV
SW
SW
SW
C113
FOCUS
a.s.in.
1
22n L103 LED X4_
+
R123
119
1 uH 27 uH + X3
X4
R119 47k
14
AV1/AV2 11
15
10
K103
8
100 om
A.OUT
L101 X201
V_OUT
+5st.by
EXT.V.IN
A.S IN
A_IN1
G_SC
B_SC
R_SC
S.SW
22 uH
+5
KEY
LED
+12
FB
VARIANTS
IR
CRT TUBE
14" 15" 20" 21" 21" RF SOUND SYSTEM
PART
C245
+5st.by
V_OUT
1-BG/I 2-BG/DK
4
237 3
2
R202 10 om R203
A.OUT
EXT_V.IN
EXT_V.IN
C202
+8
GND
LED
KEY
130 +8d
A33EKC02X01
A36EKM72X11
A48EKB02X01
A51EJJ04X01
A51EKS41X11
AUD
100 om
G_SC
B_SC
R_SC
R124 TPS 5,5 TPS 5,5
238
C203
IR
b.out1
R201 + Z1
150 om
KS3300
233
ETH VT202 L203
KS3610
KS4816
KS5160
KS5171
R206 100 om
47p C204
100n
g.out1
R125 100p 22.0 L202 TPS 6,5
C201 47.0 4.7 uH
FB
22 uH Z2
91 om
VT101 R207 VD203 BC547
235
100 om 1k
R205
+
100 om
R208 100 om
BC547 27k TPS 6,0
5
1N4148 Z3
C116
100n
C206
C205
VT201 PART
2.2n
234
X203 VT102 A_SC
R204 10k
F1 K2962 K2955
206
X5 121 BC547 BC557 100n TT2 OFF ON ON
C115 OFF
207
100n
R127 C208 Z1
R209
120k +3.3 +3c TPS 5.5 TT3 OFF OFF OFF
C210
ON
int.v.in1
100p
10.0 VT204
+
to FRONT BOARD +8b
+
R128 L205 L201 33 uH
203
VT203
+8c
100.0
C207
123 BC557 R211 R212 TT4 OFF OFF ON ON
33 uH
231
229
R129 +5 BC547 Z2
470 om R210 TPS 6.5
1k 330 om L204 100 om R213 TT6 ON OFF ON OFF
204
205
C214 236
VD202
33 uH
9.1v
100 om VD201
C215
+3a 100.0
47p 100 om TT12 ON ON ON ON
230
201
180 om
Z3
C212
C216
100n
+
47p
R214
2.4v
100n + TPS 6.0
C218
C211 47n
TT13 OFF OFF OFF OFF
C221
47.0
R215 R216 XT1 R217 27k
C217
R245
C213 47n
R219 390 om
C219 TT14 OFF OFF OFF OFF
202
10k
ex.v.in
10k
int.v.in
100n 1k
R218 100 om 100n 1n
47n
R220 360k L502 105 uH 39 uH 105 uH 105 uH
i.cut
208
SCL1 scl_1 C222 ETH
b.out
g.out
r.out
12 mHz
227
F1 K2955 T501 CF0801 CF0801 CF0801 CF0801
46C220
209
R221 100 om R222 27k
228
R228 SDA1 sda_1 226 210 FLYB -4780 -4780 -4780 -4780
r
IR
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
48
47
45
44
43
42
41
40
39
38
37
36
35
34
33
IR_
TU101 R223 100 om H.DR MUTE 1,03 V/0,31V
R225
1
211
IF2
100 om
R224
124
+3.3 V
+3.3V
VPE
+3.3 V
B out
G out
R out
I cutoff
G/Y
FB
XTAL out
A_out/AM out
+8V
IF_CVBS out
Hout
RESET
SVHS_chrom
IF_pll
A_ext in/Qss_out
EHT
P1.2/NT0
P1.1/T0
BCL
EXT_ CVBS/Y in
GndTV1
INT_CVBS in
P1.0/INT1_ IR
XTAL in
OSC_gnd
B/U(b-y)
R/V(r-y)
H_fb/SSC
11 C223 4.7 +15 R605 C603
100 om
AUD 1.8k
+
1 uH 10n
10 125 +30 47.0
IF2
8
750 om
SCART-SW_(p3.3/adc3)
VD103 IC202 TDA9351 R243
SDA
TEST
SCL
Vcc
DEC_sdem/SIFin2
3k
MUTE_p3.0/adc0)
22n 100k
V.tune(p2.0/pwm)
AUD_dem/SIFin1
R130 27 om
24C08W6
SND_pll/SIFagc
C118 +8 KEY(p3.2/adc2)
ON/OFF_(p1.3)
+ 220n
IC201
+8 R604
4.7
REFO/AMout
8
VHF-1(P0.5)
VHF-3(P0.6)
NC C121 100.0 -OUT2
+5
100.0
GND
2.2 om
DEC_dig
GND_cp
DEC_bg
GndTV2
100n
SEC_pll
22n
L105
VssTV3
AVL/ew
A0
A1
A3
GND_a
VDR_B
VDR_A
PH2_lf
PH1_lf
IF_in1
IF_in2
7 + VD104 R603 C606 + X_2
22 uH
AGC
+5V
+8 V
SDA
VSC
I_ref
SCL
9
5.1v C602
390 om
C122
470.0
C123
+
1
4
R134 3.3k
R133 3.3k
N.C.
+VS
+OUT
N.C.
-OUT
C120
IN
S_GND
VC
P_GND
6 +5.tun 217 1n
+5V
10
11
12
13
220n 14
15
16
17
18
19
20
C226 21
22
23
24
25
26
27
28
29
30
31
32
1
C225
s.w 215 + 220
100 om
218
C232
220n
AV1/2
39.2k
5 sda.tun SDA SCL. KY
MUT
SDA
R229 100 om
100 om
R230 100 om
SDA.
R136 IC601 TDA7056A
C233 4.7
+5st.by
R233 100 om
100n
100 om
R234 100 om
4 C228
3
SCL C236
R232
R138 221 3.9k
LED C231 V DEFLECTION
1.2n
127 +
R231
C227
C230
100n IC401 STV9302A
3 223 330p COIL
C235
NC 680 om
100n
X501
R236
R137 2.2
+
+
10k C239
C240
R139 R140 C238 10.0 R401 3
240
C237
1n
NC 2 4.7k 128 R407 401
100.0 C241 22n 1.2n VD+ 2.7k
4
1
R143 4.7n 406
10k C242 C401 C402 C403
12k R251 +8e
W11 1k TT2
1 VT103 +5 R242 * 1
R239 3.3k
R241 1.2k
R402
R240 10k
2.7 om
R238 10k
AGC
R404
BC547 2.2k C244 22n 100n 100n
+
15k C408 404 2.7k 470 om
10 om
2.2k L206
R403
VD105 R142 C243 1n C246 3.3n 402 403 2
AV1/AV2
216 1.0
C124 22 uH + 10.0 1n *
KEY
VD204
ON/OFF
22.0 + 47.0
AGC
VD+
100n H DEFLECTION
VD-
-14
IF1
IF2
47k
S.SW
A_SC
R406 R501 COIL
TU101 FB +3.3 VD- 3 om T501
+8
R141
+
AGC
+ 0.47 om PET-21-07
C407 VD401 VD502
1k C502 516
680 om R321 VD312 RGP15D 1n 470.0 RGP15J 8 HV
+15 1N4002 515 R502 L502
301
14
!
+ C328
0.22 om 1k HL105UH
336
!
VD301 VD302 + R307 R504
C303 39k 680p 0.47 om 680p
1N4007 1n 1n 100.0 27n T301 C318 +8 C406 470.0 680p
!
1N4007 BCK-35-0218 7 VD504
340 VD309 RG2 100.0 518 517 R503
R315
C505
335 100n
330n
R310 8 326 +110 * RGP15J 22k
7 2
304
305
VD501 VD503
100n
39k + R312
0.22 om
327
VD306 R304
C506
514
C305 C317 FLYB 501
R301
MF72
C517
1n 1n 470p +12
+
+
RG2 316
3
IC302
3
VD505 R505 1k TT6
318
R303 322 2 3 +8 HV
IN OUT L501
302
328
317
333
STP5NK60Z
331
MZ72K18RM270 1 7 VD315 ON/OFF VT502 T502 C508
9.6 nF -5%+3%
!
COMP Vcc 1N4148 27 om 12 1.2k 4.7n
!
BSR52 TT3
C516
3 5
330p
100n + 505 504 R506 47n
180k
511
ET2448 BC547 10.0 C512
R317 680 om
C509
X502X_4
519
R314 5 3 312 314 H.DR 520 2 C510
GND Isens 6 11
220n 308
508
VD310 R309 100n ST1803DHI TT4 2
IC303
270 om
510
C319
R508
Rt/Ct Vref L78L33ACZ VD507
!
307
323
320
334
!
HD.TR
! !
VD311 332 3 1 10.0 180k 4
X301
470 om
507
509
4.7n 10n 100n VD510 E1
C312
47.0
!
2
+
100.0 100n ETH 1N4002 2.4 om
DEGAUSSING COIL C322
!
2.2n
!
2005.01.07