Professional Documents
Culture Documents
page CONTENTS
2 Introduction
CX250 Two Channel
MOSFET Car Audio 2 What is included?
CX450 Amplifiers
CX550 3 Features
CX750 3 About 2 Ohm operation
CX950 4 General precautions
CX1250
4 Installation precautions
CX600 Four Channel
MOSFET Car Audio 4 Mounting the amplifier
CX650 Amplifiers
5 Connecting the amplifier
CX800
CX1000 6 Low level input wiring
9 High level input wiring
CX1800 Five Channel
MOSFET Car Audio
Amplifier 12 2CH Power and Speaker wiring
2CH and Bridged Modes
CX1100M MonoBlock
MOSFET Car Audio 13 2CH Power and Speaker wiring
CX2000M Amplifier TriMode
Never operate the amplifier when it is SHOCK HAZARD! Do not open the case
unmounted. Attach all audio system of this product. There are dangerous
components securely to prevent voltages present within the unit. There are
no user-serviceable parts within the unit.
damage, especially in an accident.
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
Remote Subwoofer
2-Channel Amplifiers Level Control
CX250, CX450, CX550,
CX750, CX950, and CX1250
REMOTE SUBWOOFER
LEFT RIGHT LEVEL CONTROL
INPUT BASS
POWER LEVEL BOOST 130 PROTECTION
100 145 HIGH PASS
To Audio
Outputs of head
unit or signal
processor
4-Channel Amplifiers
CX600, CX650, CX800, and CX1000
Remote Subwoofer
Level Control
1
CH CH2 CH3/4 CONTROLS
CROSSOVER LOW PASS INPUT INPUT BASS LOW PASS CROSSOVER
POWER MODE FREQ LEVEL LEVEL BOOST FREQ MODE PROTECTION
100 145 100 145
40 155 40 155
FULL 35 Hz 160 MIN MAX MIN MAX 0 +12dB 35 Hz 160 HIGH PASS
RANGE FULL RANGE
CH1/2 CONTROLS REMOTE
SUBWOOFER
LEVEL CONTROL
LOW
3 LEVEL 4
CH CH
2 + HIGH
CH CH
+ 1 LEVEL + 3 4+
CH CH
FOUR CHANNEL
MOS FE T P OW ER A MP LI FIE R INPUTS
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
CH1/2 CONTROLS
CH 1 3
CH INPUT CONTROLS CROSSOVER
HIGH
BASS BOOST
5R
CH INPUT CONTROLS CROSSOVER
SENSITIVITY LEVEL MODE 0 +18dB FULL LOW PASS
FULL PASS FREQ SENSITIVITY LEVEL
Hz
CH CH FREQ
+ 1 2+
100mV-2V 2-8V MIN LOW PASS 45 90
MAX 45 90 100mV-2V 2-8V MIN MAX Hz
CH CH
HIGH PASS Hz 4CH 5CH
HIGH + 3 4+ POWER
LEVEL
INPUTS PROTECT
MIN MAX FULL 45 90 5L
CH 0 +18dB
2
CH CH 4 100mV-2V 2-8V LOW PASS FREQ 0 +18dB INPUT MODE BASS BOOST
REMOTE SUBWOOFER
SENSITIVITY LEVEL MODE
LOW LEVEL INPUTS INPUT CONTROLS CROSSOVER BASS BOOST CH5 INPUTS CH5 CONTROLS LEVEL CONTROL
CH3/4 CONTROLS
To SUBWOOFER
Audio Outputs of
head unit or signal
processor (if
present)
To FRONT Audio To REAR Audio
Outputs of head Outputs of head
unit or signal unit or signal
processor processor
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
MonoBlock Amplifier
CX1100M
Remote Subwoofer
Level Control
MonoBlock Amplifier
CX2000M
Remote Subwoofer
Level Control
LEFT RIGHT
INPUT BASS CROSSOVER
POWER LEVEL BOOST FREQUENCY PROTECTION
+ L R+ REMOTE SUBWOOFER
LEVEL CONTROL
HIGH LEVEL LOW LEVEL MIN MAX 0 +12dB 40Hz 120Hz
INPUTS
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
2-Channel Amplifiers
CX250, CX450, CX550, CX750, CX950, and CX1250
Remote
Subwoofer Level Control
REMOTE SUBWOOFER
LEFT RIGHT LEVEL CONTROL
INPUT BASS
POWER LEVEL BOOST 130 PROTECTION
100 145 HIGH PASS
L+ L- R- R+
To Speaker Terminals
of head unit
Remote
Subwoofer Level Control
4-Channel Amplifiers
CX600, CX650, CX800, and CX1000
CH1 2
CH CH3/4 CONTROLS
CROSSOVER LOW PASS INPUT INPUT BASS LOW PASS CROSSOVER
POWER MODE FREQ LEVEL LEVEL BOOST FREQ MODE PROTECTION
100 145 100 145
40 155 40 155
FULL 35 Hz 160 MIN MAX MIN MAX 0 +12dB 35 Hz 160 HIGH PASS
RANGE FULL RANGE
CH1/2 CONTROLS REMOTE
SUBWOOFER
LEVEL CONTROL
3 LOW HIGH 3
CH CH CH CH
LEVEL
CH 4
CH
+ 1 2 + LEVEL + 4+
FOUR CHANNEL
MOS FE T P OW ER A MP LI FIE R INPUTS
To Speaker
CH CH CH CH
1+ 1- 2- 2+ Terminals
of head unit
CH CH CH CH
3+ 3- 4- 4+
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
5-Channel Amplifier
CX1800 Remote
CH1+ CH1- CH2- CH2+
Subwoofer Level Control
To Speaker Terminals
of head unit
CH1/2 CONTROLS
CH 1 3
CH INPUT CONTROLS CROSSOVER BASS BOOST
5R
CH INPUT CONTROLS CROSSOVER
SENSITIVITY LEVEL MODE HIGH 0 +18dB
FULL PASS
FREQ SENSITIVITY LEVEL FULL LOW PASS
Hz
CH CH FREQ
+ 1 2+ LOW PASS
100mV-2V 2-8V MIN MAX 45 90 100mV-2V 2-8V MIN MAX 45 Hz 90
CH CH
Hz 4CH 5CH
HIGH + 3 4+ HIGH PASS
POWER
LEVEL
INPUTS 0 +18dB PROTECT
MIN MAX FULL 45 90 5L
CH
2
CH CH 4 100mV-2V 2-8V LOW PASS FREQ 0 +18dB INPUT MODE BASS BOOST
SENSITIVITY LEVEL MODE REMOTE SUBWOOFER
LOW LEVEL INPUTS INPUT CONTROLS CROSSOVER BASS BOOST CH5 INPUTS CH5 CONTROLS LEVEL CONTROL
CH3/4 CONTROLS
NOTE: Do not connect BOTH the high level and low level inputs from your
receiver to your amplifier at the same time!
MonoBlock Amplifier
CX1100M
L+ L- R- R+
Remote
Subwoofer Level Control To Speaker Terminals
of head unit
MonoBlock Amplifier
CX2000M
LEFT RIGHT
INPUT BASS CROSSOVER
POWER LEVEL BOOST FREQUENCY PROTECTION
+ L R+ REMOTE SUBWOOFER
LEVEL CONTROL
HIGH LEVEL LOW LEVEL MIN MAX 0 +12dB 40Hz 120Hz
INPUTS
L+ L- R- R+ Remote Subwoofer
To Speaker Terminals Level Control
of head unit
+ LEFT
Speaker
+ RIGHT
Speaker SPEAKER
Two IMPEDANCE
2-8 OHMS
Channel
Mode
SPEAKER CONNECTIONS
POWER CONNECTIONS
L R BATT+ REMOTE GROUND
FUSE
BRIDGED
Chassis
ground
point
to REMOTE TURN-ON
terminal of head unit
FUSE Battery
+ Subwoofer
SPEAKER
IMPEDANCE
4-8 OHMS
Bridged
Mode
SPEAKER CONNECTIONS
POWER CONNECTIONS
L R BATT+ REMOTE GROUND
FUSE
BRIDGED
Chassis
ground
point
Connect the Positive (+) terminal of the
subwoofer to the L (+) amplifier terminal. to REMOTE TURN-ON
terminal of head unit
Connect the Negative (-) terminal of the
subwoofer to the R (-) amplifier terminal.
FUSE Battery
To set up the amplifier to run in this mode, put the crossover switches in the FULL position.
Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown
below. Be sure to check the table at the bottom of this page to determine the correct
capacitor and inductor values for the crossover frequency you wish to achieve.
Tri-Mode
FUSE
BRIDGED
Chassis
ground
point
High pass filter
crossover to REMOTE TURN-ON
terminal of head unit
LEFT
Speaker
MINIMUM
SPEAKER
FUSE Battery
High pass filter
IMPEDANCE crossover
4 OHMS
RIGHT
Speaker
SPEAKER
Low pass IMPEDANCE
filter inductor 8 OHMS
Subwoofer
CH2
Speaker SPEAKER
IMPEDANCE
CH1
2-8 OHMS
Speaker
Four
Channel
Mode
FUSES
SPEAKER CONNECTIONS
POWER CONNECTIONS
CH 1 CH2 CH 3 CH4 BATT+ REMOTE GROUND
CH1/2 CH3/4
BRIDGED BRIDGED
Chassis
ground
CH3 point
SPEAKER
Speaker
IMPEDANCE to REMOTE TURN-ON
2-8 OHMS terminal of head unit
CH4
Speaker
FUSE Battery
SPEAKER
IMPEDANCE
4-8 OHMS
Connect the Negative (-) terminal of the RIGHT subwoofer to
the CH2 (-) amplifier terminal.
RIGHT
Subwoofer
Connect the Positive (+) terminal of the RIGHT subwoofer to
the CH1 (+) amplifier terminal.
Bridged
Mode
FUSES
SPEAKER CONNECTIONS
POWER CONNECTIONS
CH 1 CH2 CH 3 CH4 BATT+ REMOTE GROUND
CH1/2 CH3/4
BRIDGED BRIDGED
Chassis
ground
point
LEFT
Subwoofer to REMOTE TURN-ON
terminal of head unit
Connect the Negative (-)
SPEAKER
terminal of the LEFT
IMPEDANCE subwoofer to the CH4 (-)
4-8 OHMS amplifier terminal. FUSE Battery
Tri-mode operation allows you to connect this amplifier to a pair of main speakers
plus a subwoofer on one pair of output channels. The main speakers will operate
in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL
position. Insert high pass filter capacitors and a low pass filter inductor into the
wiring as shown below. Be sure to check the table at the bottom of this page to
determine the correct capacitor and inductor values for the crossover frequency
you wish to achieve.
SPEAKER
IMPEDANCE
8 OHMS
Tri-Mode RIGHT
Subwoofer
Component values for
6dB Passive Crossover High pass filter
crossover CH3
FREQUENCY INDUCTOR CAPACITOR
Speaker
80 Hz 7.5mH 470uF
MINIMUM
100 Hz 6.5mH 330uF High pass filter SPEAKER
120 Hz 5.5mH 330uF crossover IMPEDANCE
150 Hz 4mH 220uF 4 OHMS
CH4
Speaker
Low pass
filter inductor
FUSES
SPEAKER CONNECTIONS
POWER CONNECTIONS
CH 1 CH2 CH3 CH 4 BATT+ REMOTE GROUND
CH1/2 CH3/4
BRIDGED BRIDGED
Chassis
ground
point
Low pass
filter inductor
LEFT
SPEAKER Subwoofer
IMPEDANCE
8 OHMS
Five
Channel
Mode CH5
Subwoofer + CH1
Speaker
SPEAKER
SPEAKER + CH2 IMPEDANCE
Speaker 2-8 OHMS
IMPEDANCE
2-8 OHMS
CH1/2 BRIDGED
SPEAKERS
FUSES POWER CONNECTIONS
CH 1 CH2
CH5 GROUND REMOTE BATT+
Chassis
ground
point
SPEAKER
IMPEDANCE CH3 to REMOTE TURN-ON
2-8 OHMS Speaker terminal of head unit
CH4
Speaker FUSE Battery
Bridged
Mode
CH1/2 BRIDGED
SPEAKERS
FUSES POWER CONNECTIONS
CH 1 CH2
CH5 GROUND REMOTE BATT+
Chassis
ground
point
to REMOTE TURN-ON
SPEAKER LEFT terminal of head unit
IMPEDANCE Subwoofer
4-8 OHMS
FUSE Battery
Tri-mode operation allows you to connect this amplifier to a pair of main speakers
plus a subwoofer on one pair of output channels. The main speakers will operate
in STEREO while the subwoofer simultaneously operates in MONO.
To set up the amplifier to run in this mode, put the crossover switches in the FULL
position. Insert high pass filter capacitors and a low pass filter inductor into the
wiring as shown below. Be sure to check the table at the bottom of this page to
determine the correct capacitor and inductor values for the crossover frequency
you wish to achieve.
SPEAKER
IMPEDANCE
Tri-Mode Low pass RIGHT
8 OHMS
filter inductor
Subwoofer
Component values for
6dB Passive Crossover High pass filter
crossover CH1
FREQUENCY INDUCTOR CAPACITOR
Speaker
80 Hz 7.5mH 470uF
100 Hz 6.5mH 330uF MINIMUM
120 Hz 5.5mH 330uF High pass filter SPEAKER
crossover IMPEDANCE
150 Hz 4mH 220uF
4 OHMS
CH5 CH2
Subwoofer Speaker
SPEAKER
IMPEDANCE
2-8 OHMS
CH1/2 BRIDGED
SPEAKERS
FUSES POWER CONNECTIONS
CH 1 CH 2
CH5 GROUND REMOTE BATT+
CH3 CH3/4 CH 4
BRIDGED
Chassis
ground
point
to REMOTE TURN-ON
terminal of head unit
High pass filter
crossover
CH4 FUSE Battery
+ Speaker
High pass filter MINIMUM
crossover SPEAKER
IMPEDANCE
CH3 4 OHMS
+ Speaker
SPEAKER
IMPEDANCE
8 OHMS Low pass
filter inductor
LEFT
Subwoofer
+ Speaker
SPEAKER
IMPEDANCE
MonoBlock 2-8 OHMS
Mode
Chassis
ground
point
to REMOTE TURN-ON
terminal of head unit
FUSE Battery
High hiss in the Disconnect all RCA inputs to the amplifiers. If the hiss disappears, then
speakers. plug in the component driving the amplifier and unplug its inputs. If the
hiss disappears at this point, go on until the faulty/noisy component is
found.
It is best to set the amplifier's input level control as low as possible. The
best subjective signal-to-noise ratio is achieved in this manner. Try to set
the head unit as high as possible (without distortion) and the amp input
level as low as possible.
Amplifier gets Check that the minimum speaker impedance for the amp model is correct.
very hot. Check that there is good air circulation around the amp. In some
applications, it may be necessary to add external cooling fan(s).
Engine noise This is usually caused by poor quality RCA cables,which can pick up
(static type) radiated noise. Use only the best quality cables, and route them away
from power cables.
Engine noise Check that speaker leads are not shorted to the vehicle chassis.
(alternator Check that the RCA grounds are not shorted to the vehicle chassis.
whine) Check that the head unit is properly grounded.
5-Channel MonoBlock
4-Channel MOSFET MOSFET
MOSFET Amplifiers Amplifier Amplifiers