Professional Documents
Culture Documents
Please note:
The functions and solutions described in this entry are mainly limited to the
realization of the automation task. Please also take into account that corresponding
protective measures have to be taken in the context of Industrial Security when
connecting your equipment to other parts of the plant, the enterprise network or the
Internet. For more information, please refer to Entry ID 50203404.
http://support.automation.siemens.com/WW/view/en/50203404
Copyright Siemens AG 2013 All rights reserved
Preliminary measures 2
Project Migration 3
Post-Processing 4
SIMATIC
WinCC (TIA Portal) Migration 5
Glossary
Guide
Related Literature 6
History 7
Copyright Siemens AG 2013 All rights reserved
Note The Application Examples are not binding and do not claim to be complete with
regard to configuration, equipment or any contingencies. The application
examples do not represent customer-specific solutions; they are only intended to
provide support for typical applications. You are solely responsible for the correct
operation of the described products. These Application Examples do not relieve
you of your responsibility to use sound practices in application, installation,
operation and maintenance. Through using these Application Examples, you
acknowledge that we will not be liable for any damage/claims beyond the liability
clause described. We reserve the right to make changes to these Application
Examples at any time and without prior notice. If there are any deviations
between the recommendations provided in this Application Example and other
Siemens publications e.g. Catalogs the contents of the other documents shall
have priority.
We do not accept any liability for the information contained in this document.
Any claims against us based on whatever legal reason resulting from the use of
the examples, information, programs, engineering and performance data etc.,
described in this Application Example shall be excluded. Such an exclusion shall
not apply in the case of mandatory liability, e.g. under the German Product Liability
Copyright Siemens AG 2013 All rights reserved
Preface
Objective of Migration Guide
It is the objective of the Migration Guide to help you migrate from WinCC flexible to
WinCC (TIA Portal). Where required, further information on changing from STEP 7
to TIA Portal will be provided.
Validity
The Migration Guide applies to
WinCC flexible
STEP 7
WinCC V12 Basic / Comfort / Advanced or higher.
Basically transferrable to later versions.
Note
The documentation specifies which WinCC flexible or STEP 7 version is required
for migration to WinCC V12 Basic / Comfort / Advanced.
Table of Contents
Warranty and Liability ................................................................................................. 4
Preface .......................................................................................................................... 5
Table of Contents ......................................................................................................... 6
1 Task ..................................................................................................................... 7
2 Preliminary Measures........................................................................................ 9
2.1 Information on the products ................................................................. 9
2.2 TIA Selection Tool .............................................................................. 10
2.3 PC Hardware and Operating System Requirements ......................... 11
2.4 Software Compatibility........................................................................ 12
2.5 TIA Portal ........................................................................................... 13
2.5.1 Overview HMI Software...................................................................... 13
2.5.2 Overview STEP 7 Software ................................................................ 15
2.6 Software required for migration .......................................................... 16
2.7 Licenses ............................................................................................. 18
2.8 Migration Requirements ..................................................................... 20
2.8.1 WinCC flexible project ........................................................................ 20
Copyright Siemens AG 2013 All rights reserved
1 Task
Introduction
You are currently using SIMATIC STEP 7 and WinCC flexible to create automation
programs.
You wish to migrate to the TIA Portal in order to use the new functionalities of the
Comfort Panels, for example.
This Migration Guide will help you with the migration.
The Migration Guide summarizes information already available on this topic and
offers help in a targeted way.
This will help you to clarify many points in advance, so that you can migrate from
STEP 7 / WinCC flexible to TIA Portal without problems.
Case 1
You have so far been using STEP 7 to create the SPS program and
WinCC flexible for the HMI configuration.
Now you are planning to continue these projects with the TIA Portal.
=> Completemigration of existing configurations into the TIA Portal.
New configurations shall be created with the TIA Portal from the start.
Case 2
You have so far been using STEP 7 to create the SPS program and WinCC flexible
for the HMI configuration.
The SPS program will continue to be processed with STEP 7. You wish to continue
the HMI project with the TIA Portal.
=> Partialmigration of existing configurations into the TIA Portal.
New SPS configurations will continue to be created with STEP 7. The HMI
configuration only shall be created with the TIA Portal from the start.
=> Combined configuration WinCC (TIA Portal) and STEP 7 V5.x
Case 1 Case 2
STEP 7 + WinCC flexible project WinCC flexible project
TIA Portal
Copyright Siemens AG 2013 All rights reserved
2 Preliminary Measures
Requirements and information
Before you migrate to the TIA Portal please find out about the following points:
PC hardware requirements
The operating system used by the target computer
Compatibility with software already installed
Required licenses
etc.
Open the Industry Online Support page via the following link
http://support.automation.siemens.com.
Enter the search term in the search field and press Enter to confirm your input.
No. Action
2. Search scope
You can limit the search scope in order get a better overview of the entries listed. To do this, use
one of the following options.
Service & Support
Manuals/operating instructions
Downloads
FAQ
Whats new
Forum
Usually the Migration Guide will refer to the search areas Service & Support or Whats new.
Copyright Siemens AG 2013 All rights reserved
You can access the TIA Selection Tool via the following link
http://www.siemens.com/tia-selection-tool. The website will provide further details
concerning this tool.
Open the Industry Online Support page via the following link
http://support.automation.siemens.com.
Enter the search term delivery release WinCC V12.
Alternatively, for STEP 7 V12, for example delivery release STEP 7 V12.
Acknowledge your entry with ENTER.
Limit the search scope to Whats new.
Select the entry delivery release .....
Copyright Siemens AG 2013 All rights reserved
You may use the tool to check an existing configuration for compatibility or, as in
this case, use the tool to check your configuration with regard to the extension with
the TIA Portal.
Brief description
The first step is to select a main component such as WinCC flexible or STEP 7,
in order to request the desired compatibility statement.
You can add further components to this main component, such as operating
systems, virus scanners, etc.
After having selected the required components you will get the compatibility
statement.
For a detailed description please see the website of the compatibility tool by
clicking on the " Help tab.
WinCC Professional
Depending on the selected edition, different HMI operator panels can be
configured. A higher edition always includes the HMI operator panels of the
lower edition.
With the WinCC Comfort software, for example, you can configure alle HMI
operator panels listed under WinCC Basic and WinCC Comfort.
The diagram shows an overview of the engineering software and the possible
target systems.
Figure 2-2
Note
The components for WinCC Comfort and WinCC Advanced will be installed
together with the engineering software WinCC Basic, for example.
The functional range of the engineering software will be activated through the
license used. So later on you can adapt the functional range to your requirements
by upgrading your existing license. There is no need for a new software installation.
Case 2
You have a configuration computer with only the following software installed:
STEP 7 V12 and WinCC V12.
In order to migrate an existing WinCC flexible or STEP 7 configuration into the TIA
Portal on this PC, certain requirements must be met.
The possible setups for case 2 will be described in the following.
Copyright Siemens AG 2013 All rights reserved
Example 1
You have a WinCC flexible configuration to be migrated.
In this case only WinCC (TIA Portal) must be installed on the PC.
Summary
Table 2-5
Start situation Migration Required software
WinCC flexible 2008 SP3 Project WinCC Basic/Comfort/Advanced
(depending on the operator panel
used)
Example 2
You have a STEP 7 V5.x configuration to be migrated.
In this case STEP 7 V5.x and STEP 7 V12 must be installed on the PC.
For details on the STEP 7 requirements please see
Entry ID 62100731.
Alternatively, using the Migration Tool, you can convert the source project into
the migratable *.ap12 file format. This file can be imported through the TIA
Portal. Then you will not need STEP 7 V5.x on the PC.
Notes
For WinCC V12 or higher you will find the migration tool on the installation
DVD under the Support Migration_Tool_TIA_V12.exe folder.
Install the migration tool on the PC that STEP 7 V5.x is installed on.
Summary
Table 2-6
Start situation Migration Required software
STEP 7 V5.x project STEP 7 V5.x
STEP 7 V12
STEP 7 V5.x project STEP 7 V12
Migration tool
Convert *.ap12 file format
Example 3
You have a STEP 7 V5.x configuration with an integrated
WinCC flexible 2008 SP3 project to be migrated.
In this case STEP 7 V5.x, WinCC flexible, STEP 7 V12 and WinCC V12 must be
installed on the PC.
Alternatively, using the Migration Tool, you can convert the source project into
the migratable *.ap12 file format. This file can be imported through the TIA Portal.
Then you will not need STEP 7 V5.x or WinCC flexible on the PC.
Notes
Copyright Siemens AG 2013 All rights reserved
For WinCC V12 or higher you will find the migration tool on the installation
DVD under the Support Migration_Tool_TIA_V12.exe folder.
Install the migration tool on the PC that STEP 7 V5.x and WinCC flexible 2008
SP3 is installed on.
Summary
Table 2-7
Start situation Migration Required software
STEP 7 V5.x project STEP 7 V5.x
WinCC flexible 2008 SP3 WinCC flexible 2008 SP3
Project STEP 7 V12
WinCC Basic/Comfort/Advanced
Info: (depending on the operator panel
WinCC flexible project integrated in used)
STEP 7.
STEP 7 V5.x project STEP 7 V12
WinCC flexible 2008 SP3 WinCC Basic/Comfort/Advanced
Project (depending on the operator panel
Migration tool used)
Convert *.ap12 file format
Info:
WinCC flexible project integrated in
STEP 7.
STEP 7 version
See also chapter 2.8.2 STEP 7 project.
2.7 Licenses
Two different cases must be distinguished here:
Case 1:
Copyright Siemens AG 2013 All rights reserved
You have a WinCC flexible 2008 license on your PC and now wish to use WinCC
V12 on this PC in addition. In this case it is sufficient to purchase an upgrade
license.
(Upgrade WinCC flexible WinCC V12).
After the upgrade the WinCC flexible 2008 to WinCC V12 upgrade license will be
converted into a combined license.
With this combined license for WinCC V12 you can run both WinCC flexible 2008
and WinCC V12.
Case 2:
You do not have a WinCC flexible 2008 license on your PC and now wish to use
WinCC V12 on this PC. In this case you will need a full WinCC V12 license.
For more detailed information about the required licenses and their order numbers
please refer to the delivery release of the product used.
The following table shows an excerpt of the Excel table with the order information.
Open the Industry Online Support page via the following link
http://support.automation.siemens.com
Enter the search term delivery release WinCC V12.
Acknowledge your entry with ENTER.
Limit the search scope to Whats new.
Select the entry delivery release .....
In the order information section you will find information on the individual products and their
order numbers.
Software requirements
Projects created with WinCC flexible 2008 SP3 can be migrated to WinCC V12.
Project version
If you have a project created with a version prior to 2008 SP3 you will have to
open the project with WinCC flexible 2008 SP3 first and then save it.
Note
It is advisable to create a backup copy.
Consistent project
The WinCC flexible project must be consistent. Prior to migrating, generate the
WinCC flexible configuration. Make sure any errors or warning messages in the
project are fixed.
(TIA Portal), the operator panel will automatically be replaced by the follow-up
panel during migration. Please also refer to chapter 2.9 Selecting new panels
Software requirements
Projects created with STEP 7 V5.4+SP5 or higher can be migrated to STEP 7 V12.
You will find detailed information on this topic under the following Entry ID:
62100731.
Table 2-9
Title Basic Panel Comfort Panel
Comparison table of the old panels and their follow- Link Link
up panels.
Copyright Siemens AG 2013 All rights reserved
Table 2-10
No. Action
1. MS Excel 2003, set filter
This instruction describes how to compare two operator panels using MS Excel 2003.
Note:
You can reset the selected filter attributes by clicking on the rest filter button.
Table 2-11
No. Action
1. MS Excel 2010, set filter
This instruction describes how to compare operator panels using MS Excel 2010.
Note:
You can reset the selected filter attributes by clicking on the rest filter button.
hardware cannot easily be exchanged, you can alternatively migrate only the HMI
project to WinCC (TIA Portal) and continue to process the existing STEP 7 part
with STEP 7 V5.x.
For information on combined configurations with WinCC (TIA Portal) and STEP 7
V5.x please refer to Entry ID 73502293.
This entry describes, among other things, how to handle the variables, e.g. via
source export/source import.
3 Project Migration
This chapter describes the topic of project migration, always referring to the
migration from WinCC flexible or STEP 7 to TIA Portal.
First, read chapter 2 Preliminary Measures and check the points listed there.
Before migrating an existing configuration into the TIA Portal, create a backup
copy of the configuration.
One of the Comfort Panel features is the change from 4:3 display format to
widescreen format. This will increase the visualization surface by up to 50%.
Figure 3-1
Copyright Siemens AG 2013 All rights reserved
In the course of the project migration you will switch the existing operator panel,
e.g. a MP 277 Touch, to a Comfort Panel. Prior to switching the operator panel you
will determine how the previous image contents will be migrated into the new
format.
The TIA Portal provides a function for specifying the settings.
In the manual Migration Guide Comfort Panels, in chapter "Switching the screen
from 4:3 to widescreen, you will find information on where to make these settings
and which effects the settings will have.
You can either download the manual under Entry ID 49752044 or use this direct
link to chapter 3.3.
Figure 3-2
Copyright Siemens AG 2013 All rights reserved
If the existing CPU was replaced by an unspecified CPU, the reason might be that
you did not activate the option Include hardware configuration or that the
hardware configuration is not supported by TIA Portal.
Figure 3-3
The first step after the migration without hardware configuration is to change the
Copyright Siemens AG 2013 All rights reserved
If this message is displayed, the reason may be that you have not activated the
Include hardware configuration option.
Figure 3-4
Usually you only have to adapt the connection to the CPU in the system
configuration.
This message will be displayed if the GSD file, that you used in SIMATIC STEP 7
to configure the slaves, is not installed in TIA Portal.
Remedy
Even though the migration was not executed, a project folder was created for the
new project. This project folder contains the directory \AdditionalFiles\GSD.
All GSD files required for migration in the TIA Portal are included in this directory.
Please install these GSD files into the TIA Portal.
Brief description
1. In the TIA Portal, select the Options > Install device description file
(GSD)menu.
2. In the Install device description file dialog, select the directory containing the
GSD files. This is the subfolder \AdditionalFiles\GSD in the project folder of
the migrated project.
3. Select the GSD files from the list.
4. Click the Install button.
Copyright Siemens AG 2013 All rights reserved
After installing the missing GSD files, repeat the project migration.
Notes
You will find GSD (GSE) files also among the following points, for example.
Current GSD files can be downloaded from the Siemens Industry Online
Support pages.
GSD (GSE) files stored on the PC are listed in the STEP 7 installation
directory.
Example: C:\Program Files\Siemens\Step7\S7DATA\GSD
If you received this message, you do not have STEP 7 or not the right version of
STEP 7 installed on your PC.
If you do not wish to install STEP 7 on your PC, you can use the migration tool as a
remedy. Please refer to the information in chapter 2.6 Software required for
migration.
4 Post-Processing
4.1 Adapt controller
If the existing controller was replaced by an unspecified CPU, open the device
configuration of the PLC controller.
Select a CPU from the hardware catalog. Replace the unspecified CPU by the
CPU from the hardware catalog.
Make the required settings such as connect interface, etc.
5 Glossary
TIA Portal
The TIA Portal (Totally Integrated Automation Portal) is the engineering user
interface that the WinCC V12 Advanced or STEP 7 Professional V12 engineering
tools are operated in.
If TIA Portal is mentioned in the Migration Guide, the engineering tools WinCC
V12 and STEP 7 V12 are included.
WinCC Comfort.
WinCC Advanced.
WinCC Professional.
Figure 5-1
WinCC V12
WinCC V12 Basic
For configuring SIMATIC HMI Basic Panels.
WinCC Basic is part of the STEP 7 Basic and Professional program packages and
is not upgradable.
STEP 7 V12
Copyright Siemens AG 2013 All rights reserved
SIMATIC STEP 7 in the TIA Portal is the software for configuring, programming,
reviewing, and diagnosing all SIMATIC Controllers. It is divided into STEP 7 Basic
V12 and STEP 7 Professional V12.
6 Related Literature
Internet Links
This list is not at all complete and only represents a selection of relevant
information.
Table6-1
Topics Title
\1\ Reference to this http://support.automation.siemens.com/WW/view/en/76878921
document
\2\ Siemens Industry http://support.automation.siemens.com
Online Support
\3\ Tool Compatibility tool
http://siemens.com/kompatool
\4\ FAQ Which information is available regarding licenses for
WinCC (TIA Portal)?
http://support.automation.siemens.com/WW/view/en/74796111
\5\ FAQ Which license will you need to upgrade from an existing STEP 7
version V5.x, V10.5, or V11 to TIA Portal V12?
http://support.automation.siemens.com/WW/view/en/57775228
\6\ FAQ Which licenses will you need to upgrade from WinCC flexible 2008 or
Copyright Siemens AG 2013 All rights reserved
7 History
Table7-1
Version Date Modifications
V1.0 09/2013 First version