Professional Documents
Culture Documents
I01 EDO
(Sep,2000)
IC REGULATORS
Dropper Type
Switching Type
MultiOutput Type
CAUTION / WARNING
The information in this publication has been carefully checked and is believed to be accurate;
however, no responsibility is assumed for inaccuracies.
Sanken reserves the right to make changes without further notice to any products herein in the
interest of improvements in the performance, reliability, or manufacturability of its products.
Before placing an order, Sanken advises its customers to obtain the latest version of the relevant
information to verify that the information being relied upon is current.
Application and operation examples described in this catalog are quoted for the sole purpose of
reference for the use of the products herein and Sanken can assume no responsibility for any
infringement of industrial property rights, intellectual property rights or any other rights of Sanken
or any third party which may result from its use.
When using the products herein, the applicability and suitability of such products for the intended
purpose or object shall be reviewed at the users responsibility.
Although Sanken undertakes to enhance the quality and reliability of its products, the occurrence
of failure and defect of semiconductor products at a certain rate is inevitable. Users of Sanken
products are requested to take, at their own risk, preventative measures including safety design
of the equipment or systems against any possible injury, death, fires or damages to the society
due to device failure or malfunction.
Sanken products listed in this catalog are designed and intended for the use as components in
general purpose electronic equipment or apparatus (home appliances, office equipment, tel-
ecommunication equipment, measuring equipment, etc.). Before placing an order, the users
written consent to the specifications is requested.
When considering the use of Sanken products in the applications where higher reliability is
required (transportation equipment and its control systems, traffic signal control systems or
equipment, fire/crime alarm systems, various safety devices, etc.), please contact your nearest
Sanken sales representative to discuss and obtain written confirmation of your specifications.
The use of Sanken products without the written consent of Sanken in the applications where
extremely high reliability is required (aerospace equipment, nuclear power control systems, life
support systems, etc.) is strictly prohibited.
Anti radioactive ray design is not considered for the products listed herein.
This publication shall not be reproduced in whole or in part without prior written approval from
Sanken.
Contents
1
Selection Guide
1. Dropper Type
VO(V)
Series
Type IO(A) Variable output voltage Functions Page
name 3.3 5 9 12 15 15.7 24
(3 to 24)
SI-3000B 0.27 SI-3157B SI-3025B Variable output voltage (rise only) 24
5-Terminal, (excluding SI-3025B,
SI-3000F 1.0 SI-3050F SI-3090F SI-3120F SI-3150F SI-3157F SI-3240F SI-3025F SI-3025F, SI-3050R), 29
Multi-Function, Output ON/OFF control
SI-3000C 1.5 SI-3033C SI-3050C SI-3090C SI-3120C SI-3150C SI-3240C (excluding SI-3050R), 35
Low Dropout
SI-3000R 1.5 SI-3050R Overcurrent/overvoltage/thermal 48
Voltage Type protection,
SI-3000J 2.0 SI-3050J SI-3090J SI-3120J SI-3150J Reset (SI-3050R only) 42
3-Terminal, SI-3000N 1.0 SI-3050N SI-3090N SI-3120N SI-3150N 8
Overcurrent/
Low SI-3003N 1.0 SI-3053N SI-3123N SI-3153N 12
overvoltage/thermal
Dropout SI-3001N 1.5 SI-3051N SI-3091N SI-3121N SI-3151N SI-3241N 16
protection
Voltage Type SI-3002N 2.0 SI-3052N SI-3092N SI-3122N SI-3152N 20
SI-3000V 2.0 SI-3052V SI-3122V SI-3152V Overcurrent protection 58
3-Terminal Type SI-3000P 2.0 SI-3052P SI-3122P SI-3152P SI-3242P Overcurrent protection 54
2. Switching Type
Series VO(V)
Type IO(A) Functions Page
name 3.3 5 9 12 15 5
Surface-Mount, Separate 0.4 SAI06 SAI03 SAI04 Overcurrent/Thermal protection,
SAI 64
Excitation Type 0.5 SAI02 SAI01 Variable output voltage (rise)
Separate SI-8000E 0.6 SI-8050E SI-8090E SI-8120E Overcurrent/Thermal protection, Variable output voltage (rise) 68
Excitation Overcurrent/Thermal protection, Soft start, Output ON/OFF
SI-8000S 3.0 SI-8033S SI-8050S SI-8090S SI-8120S SI-8150S 72
Type control, Variable output voltage (rise)
0.28 SI-8213L
Self
0.3 SI-8211L
Oscillating SI-8200L
0.35 SI-8203L 78
Type with
0.4 SI-8201L
Coil
SI-8300L 1.0 SI-8301L
0.4 SI-8402L SI-8405L Overcurrent/
Separate SI-8400L
0.5 SI-8403L SI-8401L Thermal protection
Excitation 82
Overcurrent/Thermal protection
Type with Coil SI-8500L 1.0 SI-8503L SI-8501L SI-8504L SI-8502L SI-8505L
Soft start, Output ON/OFF control
SI-8800L 0.45/0.05 SI-8811L Overcurrent protection (+5V)
Separate
SI-8910L 0.3/0.1 SI-8911L Overcurrent protection (+5V)
Excitation Type 88
SI-8921L
with Transformer SI-8920L 0.6 Overcurrent protection
SI-8922L
2
3. Multi-Output Type
Type Part Number VO(V) IO(A) Regulator type Functions Page
ch 1 5 0.5 Switching
STA801M Select one from 9, Overcurrent/
ch 2 0.5 Switching
11.5, 12.1, 15.5 Thermal protection,
94
ch 1 9 0.5 Switching Output ON/OFF control,
STA802M Select one from 9.1, Soft start
2-Output ch 2 0.5 Switching
11.7, 12.1, 15.7
Output ON/OFF control,
ch 1 5 0.5 Dropper Overcurrent protection (Vo shutdown
SDI02 after operation) 100
Thermal protection
ch 2 5 0.5 Dropper Flag output function
Regulator 1 12 1.5 Dropper Variable output voltage (rise),
SLA3001M Regulator 2 5 1.5 Dropper Output ON/OFF control,
Overcurrent/Overvoltage/Thermal protec-
Regulator 3 9 1.5 Dropper tion
Regulator 1 5 0.5 Switching Overcurrent/Thermal protection
Variable output voltage (rise) ,
3-Output SLA3002M Regulator 2 15.7 1 Dropper Output ON/OFF control, Overcurrent/ 104
Overvoltage/Thermal protection
Regulator 3 9 0.4 Switching Overcurrent/Thermal protection
Regulator 1 5 0.5 Switching
SLA3004M Regulator 2 9 0.4 Switching Overcurrent/Thermal protection
Regulator 3 9 0.4 Switching
ch 1 5 0.5 Dropper Output ON/OFF control,
Overcurrent protection (Vo shutdown
ch 2 5 0.5 Dropper
SLA3005M after operation)
ch 3 5 0.5 Dropper Thermal protection
ch 4 5 0.5 Dropper Flag output function
ch 1 5 0.5 Dropper Output ON/OFF control
ch 2 5 0.5 Dropper Overcurrent protection
4-Output SLA3006M 110
ch 3 5 0.5 Dropper Thermal protection
ch 4 5 0.5 Dropper Flag output function
3
Product Index by Part Number
Part Number VO(V) IO(A) Regulator type Package Remarks Page
SAI01 5.0 0.5 Switching Surface-Mount 64
SAI02 3.3 0.5 Switching Surface-Mount 64
SAI03 12.0 0.4 Switching Surface-Mount 64
SAI04 15.0 0.4 Switching Surface-Mount 64
SAI06 9.0 0.4 Switching Surface-Mount 64
SDI02 5.0/5.0 0.5/Each output Dropper Surface-Mount 2-Output 100
SI-3025B Variable Output Voltage 0.27 Dropper 5-Terminal Full-Mold Low Dropout Voltage 24
SI-3025F Variable Output Voltage 1.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 29
SI-3033C 3.3 1.5 Dropper 5-Terminal Full-Mold Low Dropout Voltage 35
SI-3050C 5.0 1.5 Dropper 5-Terminal Full-Mold Low Dropout Voltage 35
SI-3050F 5.0 1.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 29
SI-3050J 5.0 2.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 42
SI-3050N 5.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 8
SI-3050R 5.0 1.5 Dropper 5-Terminal Full-Mold Built-in Reset Function, Low dropout Voltage 48
SI-3051N 5.0 1.5 Dropper 3-Terminal Full-Mold Low Dropout Voltage 16
SI-3052N 5.0 2.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 20
SI-3052P 5.0 2.0 Dropper 3-Terminal 55
SI-3052V 5.0 2.0 Dropper 3-Terminal Low Dropout Voltage 59
SI-3053N 5.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 12
SI-3090C 9.0 1.5 Dropper 5-Terminal Full-Mold Low Dropout Voltage 35
SI-3090F 9.0 1.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 29
SI-3090J 9.0 2.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 42
SI-3090N 9.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 8
SI-3091N 9.0 1.5 Dropper 3-Terminal Full-Mold Low Dropout Voltage 16
SI-3092N 9.0 2.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 20
SI-3120C 12.0 1.5 Dropper 5-Terminal Full-Mold Low Dropout Voltage 35
SI-3120F 12.0 1.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 29
SI-3120J 12.0 2.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 42
SI-3120N 12.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 8
SI-3121N 12.0 1.5 Dropper 3-Terminal Full-Mold Low Dropout Voltage 16
SI-3122N 12.0 2.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 20
SI-3122P 12.0 2.0 Dropper 3-Terminal 55
SI-3122V 12.0 2.0 Dropper 3-Terminal Low Dropout Voltage 59
SI-3123N 12.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 12
SI-3150C 15.0 1.5 Dropper 5-Terminal Full-Mold Low Dropout Voltage 35
SI-3150F 15.0 1.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 29
SI-3150J 15.0 2.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 42
SI-3150N 15.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 8
SI-3151N 15.0 1.5 Dropper 3-Terminal Full-Mold Low Dropout Voltage 16
SI-3152N 15.0 2.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 20
SI-3152P 15.0 2.0 Dropper 3-Terminal 55
SI-3152V 15.0 2.0 Dropper 3-Terminal Low Dropout Voltage 59
SI-3153N 15.0 1.0 Dropper 3-Terminal Full-Mold Low Dropout Voltage 12
SI-3157B 15.7 0.27 Dropper 5-Terminal Full-Mold Low Dropout Voltage 24
SI-3157F 15.7 1.0 Dropper 5-Terminal Full-Mold Low Dropout Voltage 29
SI-3240C 24.0 1.5 Dropper 5-Terminal Full-Mold Low Dropout Voltage 35
SI-3241N 24.0 1.5 Dropper 3-Terminal Full-Mold Low Dropout Voltage 16
SI-3242P 24.0 2.0 Dropper 3-Terminal 55
4
Part Number VO(V) IO(A) Regulator type Package Remarks Page
SI-8033S 3.3 3.0 Switching 5-Terminal Full-Mold 72
SI-8050E 5.0 0.6 Switching 5-Terminal Full-Mold 68
SI-8050S 5.0 3.0 Switching 5-Terminal Full-Mold 72
SI-8090E 9.0 0.6 Switching 5-Terminal Full-Mold 68
SI-8090S 9.0 3.0 Switching 5-Terminal Full-Mold 72
SI-8120E 12.0 0.6 Switchin 5-Terminal Full-Mold 68
SI-8120S 12.0 3.0 Switching 5-Terminal Full-Mold 72
SI-8150S 15.0 3.0 Switching 5-Terminal Full-Mold 72
SI-8201L 5.0 0.4 Switching With Coil 78
SI-8203L 12.0 0.35 Switching With Coil 78
SI-8211L 5.0 0.3 Switching With Coil 78
SI-8213L 12.0 0.28 Switching With Coi 78
SI-8301L 5.0 1.0 Switching With Coil 78
SI-8401L 5.0 0.5 Switching With Coil 82
SI-8402L 12.0 0.4 Switching With Coil 82
SI-8403L 3.3 0.5 Switching With Coil 82
SI-8405L 15.0 0.4 Switching With Coil 82
SI-8501L 5.0 1.0 Switching With Coil 82
SI-8502L 12.0 1.0 Switching With Coil 82
SI-8503L 3.3 1.0 Switching With Coil 82
SI-8504L 9.0 1.0 Switching With Coil 82
SI-8505L 15.0 1.0 Switching With Coil 82
SI-8811L 5 0.45/0.05 Switching With Transformer 88
SI-8911L 5 0.3/0.1 Switching With Transformer 88
SI-8921L 5.0 0.6 Switching With Transformer 88
SI-8922L 5.0 0.6 Switching With Transformer 88
SLA3001M 12/5/9 1.5/1.5/1.5 DR/DR/DR 3-Output 104
SLA3002M 5/15.7/9 0.5/1/0.4 SW/DR/SW 3-Output 104
SLA3004M 5/9/9 0.5/0.4/0.4 SW/SW/SW 3-Output 104
SLA3005M 5 0.5/Each Output Dropper 4-Output 110
SLA3006M 5 0.5/Each Output Dropper 4-Output 110
SLA3007M 5/5/5/3.3 0.5/Each Output Dropper 4-Output 110
ch1:5/ch2:select one from
STA801M 0.5/Each Output Switching 2-Output 94
9, 11.5, 12.1, 15.5
ch1:9/ch2:select one from
STA802M 0.5/Each Output Switching 2-Output 94
9.1, 11.7, 12.1, 15.7
5
Ordering
Please specify a multiple of the standard minimum number of packages when ordering.
6
Dropper Type - Application Note
Temperature and Reliability Fastening Torque
The reliability of an IC is highly dependent on its operating tempera- SI-3000N
ture. Design should pay particular attention to ensuring ample space SI-3001N
for radiating heat. SI-3002N
Be sure to apply silicon grease to the IC before attaching a heatsink, SI-3003N
and to secure it firmly to the heatsink. SI-3000B 0.588 to 0.686[Nm] (6.0 to 7.0[kgfcm])
Other important items to be considered regarding heat radiation in- SI-3000F
clude air convection during operation. SI-3000C
SI-3000J
SI-3000R
Calculating Internal Power Dissipation (PD)
PD is given by the following formula: SI-3000P
PD=IO[VIN(mean)VO] SI-3000V 0.686 to 0.882[Nm] (7.0 to 9.0[kgfcm])
VIN (max.)
VIN (min.)
Others
Devices can not be operated in parallel to increase current.
When setting the DC input voltage, pay attention to the following: An isolation type diode is provided from input to ground and also
VIN(min) must be no less than the sum of output voltage and dropout from output to ground. These may be destroyed if the device is re-
voltage. verse biased. In this case, use a diode with low VF to protect them.
VIN(max) must be no more than the maximum rated DC input volt-
age.
Rectifier Diodes for Power Supplies
To rectify the AC input using rectifier diodes in power supplies, use
Heatsink Design any of the SANKEN rectifier diodes shown in the following list. (Use
The maximum junction temperature Tj(max) given in the absolute maxi- axial type diodes in a center-tap or bridge configuration.)
mum ratings is specific to each product type and must be strictly
observed. Thus, thermal design must consider the conditions of use
which affect the maximum power dissipation PD(max) and the maxi- Regulator Type Diodes
mum ambient temperature Ta(max). SI-3000N Series
To simplify thermal design, the relationship between these two pa- SI-3001N Series RM2Z(Axial Type, VRM:200V, IO:1.2A)
rameters has been presented in a graph, the Ta-PD characteristic SI-3002N Series RBV-402(Bridge Type, VRM:200V, IO:4.0A)
graph. Thermal design should include these steps: SI-3003N Series
1. Obtain the maximum ambient temperature Ta(max). SI-3000B Series AM01Z(Axial Type, VRM:200V, IO:1.0A)
2. Obtain the maximum power dissipation PD(max). SI-3000F Series
3. Look for the intersection point on the Ta-PD characteristic graph SI-3000C Series
and determine the size of the heatsink. SI-3000J Series RM2Z(Axial Type, VRM:200V, IO:1.2A)
The size of the heatsink has now been obtained. However, in actual SI-3000R Series RBV-402(Bridge Type, VRM:200V, IO:4.0A)
applications, a 10 to 20% derating factor is introduced. Moreover, the SI-3000P Series
heat dissipation capacity of a heatsink highly depends on how it is SI-3000V Series
mounted. Thus, it is recommended to measure the heatsink and case
temperature in the actual operating environment.
The Ta-PD characteristics for each product type are provided for ref-
erence purposes.
7
SI-3000N Series
SI-3000N Series
3-Terminal, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 1.0A
Low dropout voltage: VDIF1V (at IO=1.0A)
Built-in foldback overcurrent, overvoltage, thermal protection circuits
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
8
SI-3000N Series
4.20.2
3.20.2 100.2 2.80.2
40.2
0.5
7.90.2
16.90.3
a
b 2.60.15
a. Part Number
2max.
b. Lot Number
0.950.15
Pin Arrangement
(13.5)
0.85+0.2
0.1 q GND
w VO
e VIN
+0.2
0.45 0.1
P3.40.12=6.8
Plastic Mold Package Type
Flammability: UL94V-0
q w e Weight: Approx. 2.3g
9
SI-3000N Series
Block Diagram
Tr1
3 2
MIC
Reg.
Drive
Amp.
Protection
VREF
Ta-PD Characteristics
15
Infinite heatsink
With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
20
10 0
20
0 2
10 m
0 m
1 00 (2
2 .3
mm C
75 /W
7 (5.
2 )
5 C/
5 2m W
m )
(7.
6C
/W
)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
10
SI-3000N Series
Typical Characteristics
(Ta=25C)
VIN=8V
0.5 5.04 IO =0A 5
Dropout Voltage VDIF (V)
VO =5V
A
=0
0.25A
0.4 5.02 4
IO
0A
1.
0.3 5.00 3
0.1 4.96 1
0 4.94 0
0 0.2 0.4 0.6 0.8 1.0 40 20 0 20 40 60 80 100 120 140 0 1 2 3 4 5 6
Output Current IO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
12V
12 5 12
V
Output Voltage VO (V)
Output Voltage VO (V)
V
V
V
18
8 15 8
15
=0.5A
13
N=
=1.5A 3
VI
22V
6 6
2
4 4
1
2 2
0 0 0
0 2 4 6 8 10 12 14 16 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0 0.5 1.0 1.5 2.0
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
5
Output Voltage VO (V)
4
VIN=8V
IO=10mA
3
0
0 20 60 100 140 180
Case Temperature TC (C)
11
SI-3003N Series
SI-3003N Series
3-Terminal, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 1.0A
Low dropout voltage: VDIF0.5V (at IO=1.0A)
Built-in dropping overcurrent, overvoltage, thermal protection circuits
Supports constant current load and plus/minus power supplies.
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
12
SI-3003N Series
0.2
4.2
3.20.2 10
0.2
2.80.2
40.2
0.5
7.90.2
16.90.3
a
b 0.15 a. Part Number
2max.
2.6
b. Lot Number
Pin Arrangement
0.950.15
(13.5)
+0.2
0.850.1 q GND
w VO
e VIN
+0.2
0.45 0.1
P3.40.12=6.8 Plastic Mold Package Type
Flammability: UL94V-0
q w e
Weight: Approx. 2.3g
13
SI-3003N Series
Block Diagram
Tr1
3 2
MIC
Reg.
Drive
Amp.
Protection
VREF
Ta-PD Characteristics
25
With Silicon Grease
Heatsink: Aluminum
Infinite heatsink
20
Power Dissipation PD (W)
15
2002002mm (2.3C/W)
1001002mm (5.2C/W)
10
75752mm (7.6C/W)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
14
SI-3003N Series
Typical Characteristics
(Ta=25C)
0.5
8
Dropout Voltage VDIF (V)
0 0 00
0 0.2 0.4 0.6 0.8 1.0 0 2 4 6 8 10 12 14 16 5 10 15 20 25
Output Current IO (A) Input Voltage VIN (V) Input Voltage VIN (V)
15 VIN=22V
IO=0 to 1A 6V
4 10
(0.25A step)
15V 20V
10 3
18V
2 5
5
1
0 0
00 5 10 15 20 25 0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
8
Output Voltage VO (V)
15
Output Voltage VO (V)
18V
VIN=25V
16V 6 VIN=8V
22V IO=10mA
10
20V
4
Note on Thermal Protection:
5 The thermal protection circuit is intended for
2 protection against heat during instantaneous
short-circuiting. Its operation is not guaran-
0
teed for continuous heating condition such
0
0 0.5 1.0 1.5 2.0 2.5 3.0 0 20 40 60 80 100 120 140 160 as short-circuiting over extended periods of
Output Current IO (A) Ambient Temperature Ta (C) time.
15
SI-3001N Series
SI-3001N Series
3-Terminal, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 1.5A
Low dropout voltage: VDIF1V (at IO=1.5A)
Built-in foldback overcurrent, overvoltage, thermal protection circuits
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
16
SI-3001N Series
4.20.2
3.20.2 100.2 2.80.2
40.2
0.5
7.90.2
16.90.3
a
b 2.60.15 a. Part Number
2max.
b. Lot Number
0.85+0.2
0.1 q GND
w VO
e VIN
+0.2
0.45 0.1
P3.40.12=6.8
Plastic Mold Package Type
Flammability: UL94V-0
q w e Weight: Approx. 2.3g
17
SI-3001N Series
Block Diagram
Tr1
3 2
MIC
Reg.
Drive
Amp.
Protection
VREF
Ta-PD Characteristics
20
Infinite heatsink With Silicon Grease
Heatsink:Aluminum
Power Dissipation PD (W)
15
2002002mm (2.3C/W)
10 1001002mm (5.2C/W)
75752mm (7.6C/W)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
18
SI-3001N Series
Typical Characteristics
(Ta=25C)
0.4 5.02
20
5.00 IO =1.5A
0.2 1.0A
10
4.98 0.5A
0A
0 4.96 0
0 0.5 1.0 1.5 40 20 0 20 40 60 80 100 120 140 0 1 4 6 8 10
Output Current IO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
6 12
25
Output Voltage VO (V)
1 2 5
0 0 0
0 1 2 3 4 5 6 7 0 2 4 6 8 10 12 14 16 18 0 10 20 30 40
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
5
15V
25V
20
VIN=30V
VIN=30V
Output Voltage VO (V)
30V
Output Voltage VO (V)
Output Voltage VO (V)
6V
25V
10
8V
V
15
4
13V
V
8 15
20
3
6
10
2
4
1 5
2
0 0 0
0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0
Output Current IO (A) Output Current IO (A) Output Current IO (A)
5
VIN=8V
Output Voltage VO (V)
IO=10mA
4
19
SI-3002N Series
SI-3002N Series
3-Terminal, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 2.0A
Low dropout voltage: VDIF1V (at IO=2.0A)
Built-in foldback overcurrent, overvoltage, thermal protection circuits
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
20
SI-3002N Series
0.2
4.2
3.20.2 100.2 2.80.2
40.2
0.5
7.90.2
16.90.3
a
b 2.60.15 a. Part Number
2max.
b. Lot Number
0.85+0.2
0.1
q GND
w VO
e VIN
+0.2
0.45 0.1
P3.40.12=6.8
Plastic Mold Package Type
Flammability: UL94V-0
q w e Weight: Approx. 2.3g
21
SI-3002N Series
Block Diagram
Tr1
3 2
MIC
Reg.
Drive
Amp.
Protection
VREF
Ta-PD Characteristics
25
With Silicon Grease
Heatsink: Aluminum
Infinite heatsink
20
Power Dissipation PD (W)
15
2002002mm (2.3C/W)
1001002mm (5.2C/W)
10
75752mm (7.6C/W)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
22
SI-3002N Series
Typical Characteristics
(Ta=25C)
0.2
1
0 4.98 0
0 0.5 1 1.5 2 40 20 0 20 40 60 80 100 120 140 0 1 2 3 4 5 6 7 8
Output Current IO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
12 12
5
22V 3V
25V
27V
8V
12V
1
Output Voltage VO (V)
Output Voltage VO (V)
10 10V 10
4
15V
6V
15V
lO=0A 8
8
0.5A
V
3
18
1A
6 1.5A 6
2A 2
4 4
1 2
2
0 0 0
0 5 10 15 20 0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
0
0 20 60 100 140 180
Case Temperature TC (C)
23
SI-3000B Series
SI-3000B Series
5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 0.27A
Low dropout voltage: VDIF0.5V (at IO=0.27A)
Output ON/OFF control terminal is compatible with LS-TTL. (It may be directly
driven by LS-TTL or standard CMOS logic.)
Built-in foldback overcurrent, thermal protection circuits
Accurate overcurent protection starting current
SI-3157B : 0.3 to 0.7A (VIN=18V)
SI-3025B : 0.3 to 0.7A (When VIN=18V, at VO=15.7V)
0.3 to 0.75A (When VIN=18V, at VO=11.7V)
Variable output voltage type (SI-3025B) also available
Applications
For BS and CS antenna power supplies
Electronic equipment
24
SI-3000B Series
25
SI-3000B Series
3.20.2
4.20.2
0.2 0.2
10.0 2.8
0.5
4.00.2
7.90.2
16.90.3
a a. Part Number
(17.9)
b b. Lot Number
2.60.1
Pin Arrangement
(2.0)
5.00.6
SI-3157B SI-3025B
0.950.15
q GND q GND
+0.2
(4.6)
0.85 0.1 w VC w VC
(8.0)
+0.2
e VO e VO
0.45 0.1
r VOS r VREF
P1.70.74=6.80.7 3.90.7 (4.3) t VIN t VIN
8.20.7
Block Diagram
SI-3157B SI-3025B
Tr1 Tr1
5 3 5 3
MIC MIC
4
Reg.
Reg.
4
Drive
Amp.
Drive
Amp.
ON/OFF
ON/OFF
Protection
Protection
VREF
VREF
2 2
Equivalent Equivalent
to LS-TTL to LS-TTL
1 1
26
SI-3000B Series
SI-3157B
D1
*2 C0 : Output capacitor (47 to 100F)
VIN VO *1 C1 : Oscillation prevention capacitor
5 3
SI-3157B
C2 (C1: Approx. 47F, C2: 0.33F)
OPEN
+ *1 2 4 + These capacitors are required if the input line is inductive
DC Input 1 C0 DC Output
C2
C1 and in the case of long wiring. Tantalum capacitors are rec-
GND GND ommended for C1 and C0, particularly at low temperatures.
*2 D1 : Protection diode
This diode is required for protection against reverse biasing
of the input and output. Sanken EU2Z is recommended.
SI-3025B
*3 R1 : External resistor for setting output voltage
D1 *2
R2 Relationship between output voltage VO and external resis-
tors R1 and R2 is as follows.
VIN VO R1
5 3 VO=VREF 1+ (VREF=2.55V(typ.))
R2
OPEN SI-3025B R1
+ *1 2 4 *3 + R2 must be 2.55k for stable operation.
DC Input C2 C0 DC Output
1 R2
C1
*3
GND GND
Ta-PD Characteristics
15
Infinite heatsink
With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
20
0
10 20
0
10 2m
0 m
10 (2
0 .3
2m C
75 m /
7 ( 5.2 W)
5
2m C
5 m /W
(7. )
6C
/W
)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
27
SI-3000B Series
0.3 lO=0A
15.7 0.1A
10 0.2A
15.6 0.27A
0.2
15.5
5
0.1
15.4
0 15.3 0
0 0.05 0.1 0.15 0.2 0.25 0.3 40 20 0 20 40 60 80 100 120 140 0 5 10 15 20 25 30
Output Current IO (A) Ambient Temperature TC (C) Input Voltage VIN (V)
15.9 15.9
lO=0A
0.1A 15
VIN=27V
VIN=16.5
15.7 0.2A 15.7
0.27A
VIN=27V
V
15.5 15.5 25V 10
18V 25V
22V
18V 22V
15.3 15.3
16.5V
5
15.1 15.1
14.9 14.9 0
14 16 18 20 22 24 26 28 0 0.05 0.1 0.15 0.2 0.25 0.3 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
VIN=18V
lO=0A
Output Voltage VO (V)
Output Voltage VO (V)
15 15
VIN=18V
lO=10mA
10 10
5 5
0 0
0 1 2 3 4 0 20 40 60 80 100 120 140 160 180
Output ON/OFF Control VC (V) Case Temperature TC (C)
28
SI-3000F Series
SI-3000F Series
5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 1.0A
Low dropout voltage: VDIF1V (at IO=1.0A)
Variable output voltage (rise only)
May be used for remote sensing (excluding SI-3025F)
Output ON/OFF control terminal is compatible with LS-TTL.
(It may be directly driven by LS-TTL or standard CMOS logic.)
Built-in foldback overcurrent, overvoltage, thermal protection circuits
Variable output voltage type (SI-3025F) also available
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
29
SI-3000F Series
Ratings
Parameter Symbol SI-3050F SI-3090F SI-3120F SI-3150F SI-3157F SI-3240F Unit
min. typ. max. min. typ. max. min. typ. max. min. typ. max. min. typ. max. min. typ. max.
Input Voltage VIN 6*3 15*2 10*3 20*2 13*3 25*2 16*3 27*2 16.7*3 27*2 25*3 40*2 V
SI-3000F *1 4.80 5.00 5.20 8.64 9.00 9.36 11.52 12.00 12.48 14.40 15.00 15.60 14.92 15.70 16.48 23.04 24.00 24.96
VO
Output Voltage SI-3000FA 4.90 5.00 5.10 8.82 9.00 9.18 11.76 12.00 12.24 14.70 15.00 15.30 V
Conditions VIN=8V, IO=0.5A VIN=12V, IO=0.5A VIN=15V, IO=0.5A VIN=18V, IO=0.5A VIN=19V, IO=0.5A VIN=27V, IO=0.5A
VDIF 0.5 0.5 0.5 0.5 0.5 0.5
Conditions IO0.5A
Dropout Voltage V
1.0 1.0 1.0 1.0 1.0 1.0
Conditions IO1.0A
VOLINE 10 30 18 48 24 64 30 90 30 90 48 128
Line Regulation mV
Conditions VIN=6V to 15V, IO=0.5A VIN=10V to 20V, IO=0.5A VIN=13V to 25V, IO=0.5A VIN=16V to 27V, IO=0.5A VIN=17V to 27V, IO=0.5A VIN=25V to 38V, IO=0.5A
VOLOAD 40 100 70 180 93 240 120 300 120 300 120 300
Load Regulation mV
Conditions VIN=8V, IO=0 to 1.0A VIN=12V, IO=0 to 1.0A VIN=15V, IO=0 to 1.0A VIN=18V, IO=0 to 1.0A VIN=19V, IO=0 to 1.0A VIN=27V, IO=0 to 1.0A
Temperature Coefficient VO/Ta 0.5 1.0 1.5 1.5 1.5 2.5
mV/C
of Output Voltage Conditions VIN=8V, IO=5mA, Tj=0 to 100C VIN=12V, IO=5mA, Tj=0 to 100C VIN=15V, IO=5mA, Tj=0 to 100C VIN=18V, IO=5mA, Tj=0 to 100C VIN=19V, IO=5mA, Tj=0 to 100C VIN=27V, IO=5mA, Tj=0 to 100C
RREJ 54 54 54 54 54 54
Ripple Rejection dB
Conditions VIN=8V, f=100 to 120HZ VIN=12V, f=100 to 120HZ VIN=15V, f=100 to 120HZ VIN=18V, f=100 to 120HZ VIN=19V, f=100 to 120HZ VIN=27V, f=100 to 120HZ
Quiescent Circuit Iq 3 10 3 10 3 10 3 10 3 10 5 10
mA
Current Conditions VIN=8V, IO=0A VIN=12V, IO=0A VIN=15V, IO=0A VIN=18V, IO=0A VIN=19V, IO=0A VIN=27V, IO=0A
Overcurrent Protection IS1 1.2 1.2 1.2 1.2 1.2 1.2
A
Starting Current*4,7 Conditions VIN=8V VIN=12V VIN=15V VIN=18V VIN=19V VIN=27V
Control Voltage (Output ON) VC. IH 2.0 2.0 2.0 2.0 2.0 2.0
V
Control Voltage (Output OFF) VC. IL 0.8 0.8 0.8 0.8 0.8 0.8
VC Control Current IC. IH 20 20 20 20 20 20
A
*5
Terminal (Output ON) Conditions VC=2.7V
Control Current IC. IL 0.3 0.3 0.3 0.3 0.3 0.3
mA
(Output OFF) Conditions VC=0.4V
*1: "A" may be indicated to the right of the Sanken logo.
*2: VIN(max) and IO(max) are restricted by the relation PD(max)=(VIN-VO)IO=14W(SI-3240F: 18W).
*3: Refer to the dropout voltage.(Refer to Setting DC Input Voltage on page 7.)
*4: IS1 is specified at 5(%) drop point of output voltage VO on the condition that VIN=VO+3V, IO=0.5A.
*5: Output is ON even when output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, it may be directly driven by an
LS-TTL circuit.
*6: When setting output voltage to 5V or less, input voltage needs to be set to 6V or over to operate stably.
*7: A foldback type overcurrent protection circuit is built into the IC regulator. Therefore, avoid using it for the following applications as it may cause
starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage
30
SI-3000F Series
3.20.2 0.2
4.2
10.00.2 2.80.2
0.5
4.00.2
7.90.2
16.90.3
a
(17.9)
b a. Part Number
2.60.1 b. Lot Number
(2.0)
5.00.6
0.85 0.1
e VO e VO
(8.0)
+0.2
0.45 0.1 r VOS r VREF
t VIN t VIN
P1.70.74=6.80.7 3.90.7 (4.3)
8.20.7
Plastic Mold Package Type
Flammability: UL94V-0
Weight: Approx. 2.3g
1 2 3 4 5
Forming No. 1101
31
SI-3000F Series
Block Diagram
SI-3000F SI-3025F
Tr1 Tr1
5 3 5 3
MIC MIC
4
Reg.
Reg.
Drive 4
Amp.
Drive
Amp.
ON/OFF
ON/OFF
Protection
Protection
VREF
VREF
2 2
Equivalent Equivalent
to LS-TTL to LS-TTL
1 1
SI-3000F
D1
*2
Ta-PD Characteristics
(Except SI-3240F) (SI-3240F)
15 20
Infinite heatsink
With Silicon Grease Infinite heatsink
Heatsink: Aluminum With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
15
20
10 0 2002002mm (2.3C/W)
20
0 2
10 m
0 m
1 00 (2 10 1001002mm (5.2C/W)
2 .3
mm C
75 /W 75752mm (7.6C/W)
7 (5.
2 )
5 C/
5 2m W
m )
(7.
6C 5
/W
)
Without heatsink Without heatsink
0 0
30 0 25 50 75 100 30 0 25 50 75 100
Ambient Temperature Ta (C) Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO] PD=IO[VIN(mean)VO]
32
SI-3000F Series
GND 25
GND
F
VIN VO
5 3
25
The output voltage may be increased by inserting resistors REX1 be-
F
150
Output Voltage VO (V)
tween terminals No.4 (sensing terminal) and No.3 (output terminal) and
SI-X32=3.75k
REX2 between terminals No.4 and No.1 (ground terminal). R E
F
20
120
The current I4IN flowing into terminal No.4 is 1mA (typ.) so the thermal SI-3X2=3k
RE
F
characteristics may be improved compared to the method shown in 1 090 5k
15 SI-3 2.2
2=
by setting the external current IREX1 at approximately 5 times the value REX
0F
of I4IN (stability coefficient S=5). 305 5k
SI- X2=1.2
The adjusted output voltage VOUT in this case is: 10 RE
VO=V04+REX1IREX1
IREX1=SI4IN
5
The value of the external resistors may be obtained as follows:
VO-V04 V04
REX1= REX2=
SI4IN , (S-1)I4IN
0 1.0 2.0
*V04: Output voltage of SI-3000F series External Resistor REX1 (k)
S: Stability coefficient of I4IN (may be set to any value)
Note: In the SI-3000F series, the output voltage increase can be ad-
justed as mentioned above. However, when the rise is set to ap-
proximately 10V compared to output voltage V04, the necessary
output current may not be obtained due to the S.O.A. protection
circuit in the SI-3000F series.
33
SI-3000F Series
Typical Characteristics
(Ta=25C)
IO vs. VDIF Characteristics Temperature Coefficient of Output Voltage(SI-3050F) Output ON/OFF Control(SI-3050F)
0.6 5.06 6
VIN=8V
0.5 5.04 5
IO =0A
Dropout Voltage VDIF (V)
VO =5V
0.3 5.00 3
VIN=8V
IO =10mA
0.2 4.98 2
0.1 4.96 1
0 4.94 0
0 0.2 0.4 0.6 0.8 1.0 40 20 0 20 40 60 80 100 120 140 0 1.0 2.0 3.0 4.0
Output Current IO (A) Ambient Temperature Ta (C) Output ON/OFF Control Voltage Vc (V)
12
12V
5 5
8V
10 10V
A
=0
4 4
IO
0.25A
0A
IO=0A
6V
V
15
8
1.
N=
=0.5A
VI
3 =1.0A 3
6
0.5A
2 0.75A 2
4
1 2 1
0 0 0
0 1 2 3 4 5 6 0 2 4 6 8 10 12 14 16 0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6
Input Voltage VIN (V) Input Voltage VIN (V) Output Current IO (A)
12 VIN=27V
25 5
25
30
Output Voltage VO (V)
Output Voltage VO (V)
10
20 4
3V
V
V
15
40V
=1
VIN=8V
22
8
VIN
35V IO=10mA
15 3
18V
6
10 2
4
2 5 1
0 0 0
0 0.5 1.0 1.5 2.0 0 0.5 1 1.5 2 2.5 3 0 20 60 100 140 180
Output Current IO (A) Output Current IO (A) Case Temperature Tc (C)
34
SI-3000C Series
SI-3000C Series
5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 1.5A
Low dropout voltage: VDIF1V (at IO=1.5A)
Variable output voltage (rise only)
May be used for remote sensing
Output ON/OFF control terminal is compatible with LS-TTL.
(It may be directly driven by LS-TTL or standard CMOS logic.)
Built-in foldback overcurrent (SI-3033C: Drooping type overcurrent),
overvoltage, thermal protection circuits
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
35
SI-3000C Series
36
SI-3000C Series
37
SI-3000C Series
3.20.2 0.2
4.2
10.00.2 2.8
0.2
0.5
4.00.2
7.90.2
16.90.3
a a. Part Number
(17.9)
b b. Lot Number
2.60.1
Pin Arrangement
(2.0)
5.00.6
q GND
0.950.15
w VC
+0.2
(4.6)
Block Diagram
SI-3000C
Tr1
5 3
MIC
4
Reg.
Drive
Amp.
ON/OFF
Protection
VREF
Equivalent
to LS-TTL
38
SI-3000C Series
Ta-PD Characteristics
20
Infinite heatsink
With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
15
2002002mm (2.3C/W)
10 1001002mm (5.2C/W)
75752mm (7.6C/W)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
39
SI-3000C Series
VIN VO 35
5 3
VIN=VO+1V C
SI-3000C IREX REX 240
+ OPEN + 30 SI-3
2 4 V04
47F 1 47F
GND 25
GND
C
0 2 4 6 8 10
2. Variable output voltage with two external resistors External Resistor REX (k)
VIN VO
5 3
tween terminals No.4 (sensing terminal) and No.3 (output terminal) and
SI-X32=3.75k
REX2 between terminals No.4 and No.1 (ground terminal). 20
RE C
120
The current I4IN flowing into terminal No.4 is 1mA (typ.)(SI-3033C: SI-3 3k
2=
REX
0.43mA (typ.)) so the thermal characteristics may be improved com- C
090 5k
15 SI-3X2=2.2
pared to the method shown in 1 by setting the external current IREX1 at RE
approximately 5 times the value of I4IN (stability coefficient S=5). 0C
305 5k
SI- X2=1.2
The adjusted output voltage VOUT in this case is: 10 RE
VO=V04+REX1IREX1
IREX1=SI4IN
3C
5 SI-3013.9k
The value of the external resistors may be obtained as follows: REX2=
VO-V04 V04
REX1= REX2=
SI4IN , (S-1)I4IN
0 1.0 2.0
*V04: Output voltage of SI-3000C series
External Resistor REX1 (k)
S: Stability coefficient of I4IN (may be set to any value)
Note: In the SI-3000C series, the output voltage increase can be ad-
justed as mentioned above. However, when the rise is set to ap-
proximately 10V compared to output voltage V04, the necessary
output current may not be obtained due to the S.O.A. protection
circuit in the SI-3000C series.
40
SI-3000C Series
Typical Characteristics
(Ta=25C)
0.6 VO=5V
20
5.00 IO=1.5A
0.2
1.0A
4.98 10
0.5A
0A
0 4.96 0
0 0.5 1.0 1.5 40 20 0 20 40 60 80 100 120 140 0 2 4 6 8 10
Output Current lO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
6
25
4
Output Voltage VO (V)
0.5A 5
20
A
3 4 =0 lO=0A
lO
5A 0.5A
A
1. 15
=0
1A 1A
5A
lO
3
2 1. 1.5A
1A
0.5A 10
2
1
1 5
0 0
0 0 1 2 3 4 5 6 7 0 10 20 30 40
0 1 2 3 4 5 6
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
5
4 20
6V
8V
VIN=30V
30V
15
4
15V
V
VIN
25
3 15
8V
=4.
3
5V
2 5V 10
6V
2
1 5
1
0 0 0
0 0.5 1.0 1.5 2.0 2.5 3.0 0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0
Output Current IO (A) Output Current lO (A) Output Current lO (A)
lO=10mA
4 4
off
3 3
2 on 2
Note on Thermal Protection:
The thermal protection circuit is intended for
1 1
protection against heat during instantaneous
short-circuiting. Its operation is not guaran-
0 0 teed for continuous heating condition such
0 1.0 2.0 3.0 4.0 20 60 100 140 180
Output ON/OFF Control Voltage (V) Case Temperature TC (C) as short-circuiting over extended periods of
time.
41
SI-3000J Series
SI-3000J Series
5-Terminal, Multi-Function, Full-Mold, Low Dropout Voltage Dropper Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 2.0A
Low dropout voltage: VDIF1V (at IO=2.0A)
Variable output voltage (rise only) May be used for remote sensing
Output ON/OFF control terminal is compatible with LS-TTL.
(It may be directly driven by LS-TTL or standard CMOS logic.)
Built-in foldback overcurrent, overvoltage, thermal protection circuits
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
42
SI-3000J Series
43
SI-3000J Series
3.20.2
4.20.2
0.2
10.0 2.80.2
0.5
4.00.2
7.90.2
16.90.3
(17.9)
a. Part Number
b
b. Lot Number
2.60.1
(2.0)
Pin Arrangement
5.00.6
0.95
0.15 q GND
+0.2 w VC
(4.6)
0.85 0.1
e VO
(8.0)
0.45 0.1
+0.2 r VOS
t VIN
P1.70.74=6.80.7 3.90.7 (4.3)
8.20.7
Plastic Mold Package Type
Flammability: UL94V-0
Weight: Approx. 2.3g
Forming No. 1101
1 2 3 4 5
Block Diagram
SI-3000J
Tr1
5 3
MIC
4
Drive
Amp.
Reg.
ON/OFF
Protection
VREF
Equivalent
to LS-TTL
44
SI-3000J Series
Ta-PD Characteristics
25
With Silicon Grease
Heatsink: Aluminum
Infinite heatsink
20
Power Dissipation PD (W)
15
2002002mm (2.3C/W)
1001002mm (5.2C/W)
10
75752mm (7.6C/W)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
45
SI-3000J Series
VIN VO 25
5 3
20 0J
GND 12
-3
GND SI
tics of +0.2%/C.
It is important to keep the thermal characteristics in mind when adjust-
ing the output voltage.
5
0 2 4 6 8 10
2. Variable output voltage with two external resistors External Resistor REX (k)
VIN VO
5 3
20 0J
12
-3 k
The output voltage may be increased by inserting resistors REX1 be- SI X2=3
RE
Output Voltage VO (V)
tween terminals No.4 (sensing terminal) and No.3 (output terminal) and
REX2 between terminals No.4 and No.1 (ground terminal). 90 5k
J
-30 .2
The current I4IN flowing into terminal No.4 is 1mA (typ.) so the thermal SI X2=2
15 RE
characteristics may be improved compared to the method shown in 1
by setting the external current IREX1 at approximately 5 times the value
0J k
of I4IN (stability coefficient S=5). 05 .25
-3
SI X2=1
The adjusted output voltage VOUT in this case is: RE
VO=V04+REX1IREX1 10
IREX1=SI4IN
The value of the external resistors may be obtained as follows:
VO-V04 V04
REX1= REX2=
SI4IN , (S-1)I4IN 5
*V04: Output voltage of SI=3000J series 0 1.0 2.0
External Resistor REX1 (k)
S: Stability coefficient of I4IN (may be set to any value)
Note: In the SI-3000J series, the output voltage increase can be ad-
justed as mentioned above. However, when the rise is set to ap-
proximately 10V compared to output voltage V04, the necessary
output current may not be obtained due to the S.O.A. protection
circuit in the SI-3000J series.
46
SI-3000J Series
Typical Characteristics
(Ta=25C)
VIN=8V
lO=0A
0.8 40
Dropout Voltage VDIF (V)
5.00
0.4 20
lO=2A
1.5A
0.2 10
1A
0.5A
0A
0 4.98 0
0 0.5 1 1.5 2 40 20 0 20 40 60 80 100 120 140 0 5 10 15
Output Current IO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
5 12
0.4
Output Voltage VO (V)
0 0 0
0 5 10 15 0 1 2 3 4 5 6 7 8 0 5 10 15 20
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
5 12
22V 3V
25V
27V
8V
12V
Output Voltage VO (V)
10V 10
4
15V
6V
15V
8
V
3
18
6
2
4
1
2
0 0
0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0
Output Current IO (A) Output Current IO (A)
4 4
off
3 3
on Note on Thermal Protection:
2 2 The thermal protection circuit is intended for
protection against heat during instantaneous
1 short-circuiting. Its operation is not guaran-
1
teed for continuous heating condition such
as short-circuiting over extended periods of
0 0
0 1.0 2.0 3.0 4.0 5.0 0 20 60 100 140 180 time.
Output ON/OFF Control Voltage VC (V) Case Temperature TC (C)
47
SI-3000R Series
SI-3000R Series
5-Terminal, Full-Mold, Low Dropout Voltage Dropper Type with Reset Function
Features
Reset signal output (As the output rises it sends a reset signal to the micro-
computer to secure normal operation of the system. As the output drops a
reset signal is also sent out to protect the system.)
Reset signal detection output voltage level Voth is 92% of output voltage in
the standard specification. Models with different setting values for different
needs are scheduled to be added to the series.
Delay time for reset signal can be set freely by external capacitor.
Compact full-mold package (equivalent to TO220)
Output current: 1.5A
Low dropout voltage :VDIF1V (at IO=1.5A)
Applicable to battery driven equipment with built-in microcomputer.
Built-in dropping type overcurrent, overvoltage, thermal protection circuits
Low circuit current ID=typ.1.5mA(IO=0A)
Applications
Microcomputer-controlled equipment
Battery-driven micro-computer-controlled equipment
48
SI-3000R Series
49
SI-3000R Series
VIN
Input Voltage
VO+VDIF
GND
Voth VO
Voth
Output Voltage
GND
VDLY
Voltage Across
The delay time tDLY of the reset signal can
VDLYth
Delay Capacitor be calculated from the following formula:
VDLYth
O(V) tDLY= CDLY
VRSTH IDLY
Reset Signal Output
3.20.2
4.20.2
0.2
10.0 2.80.2
0.5
4.00.2
7.90.2
16.90.3
a
(17.9)
b
a. Part Number
2.60.1
b. Lot Number
(2.0)
5.00.6
Pin Arrangement
0.950.15 q GND
+0.2 w DELAY
(4.6)
0.85 0.1
e VO
(8.0)
+0.2
0.45 0.1 r Rest Signal output
t VIN
P1.70.74=6.80.7 3.90.7 (4.3)
8.20.7
Plastic Mold Package Type
Flammability: UL94V-0
Forming No. 1101 Weight: Approx. 2.3g
1 2 3 4 5
50
SI-3000R Series
Block Diagram
Tr1
5 3
MIC
Reg.
Drive
Amp.
OCP, OVP
Reset
4
TSD
VREF
1 2
Ta-PD Characteristics
20
Infinite heatsink
With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
15
2002002mm (2.3C/W)
10 1001002mm (5.2C/W)
75752mm (7.6C/W)
Without heatsink
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
PD=IO[VIN(mean)VO]
51
SI-3000R Series
Typical Characteristics
(Ta=25C)
5.04 VIN=8V
lO=10mA 5
Dropout Voltage VDIF (V)
5.02
0 4.90 0
0 0.5 1.0 1.5 40 20 0 20 40 60 80 100 120 140 0 1 2 3 4 5 6 7 8
Output Current lo (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
8V
15V
Ground Current IG (mA)
20V
25V
4 4
15
6V
3 3
10 lO=1
.5A
2 2
1A
5
0.5A 1 1
0A
0 0 0
0 5 10 15 20 25 30 0 0.5 1 1.5 2 2.5 3 60 80 100 120 140 160 180
Input Voltage VIN (V) Output Current lO (A) Case Temperature TC (C)
Note on Thermal Protection:
The thermal protection circuit is intended for
protection against heat during instantaneous
short-circuiting. Its operation is not guaran-
teed for continuous heating condition such
as short-circuiting over extended periods of
time.
Reset Output vs. VO Characteristics Reset Output vs. DLY Terminal Voltage Characteristics Reset Signal Delay Time tDLY(sec)
6 6 10
VIN=8V lO=0A VIN=8V lO=0A VIN=8V
RL=510 RL=510 lO=0A
Reset Output Voltage VRST (V)
5 5 1
Delay Time tDLY (sec.)
4 4 100m
3 3 10m
2 2 1m
1 1 100
0 0 10
3.0 3.5 4.0 4.5 5.0 5.5 6.0 1.0 1.5 2.0 2.5 3.0 3.5 4.0 1p 10p 100p 1000p 0.01 0.1 1 10
Output Voltage VO (V) DLY Terminal Voltage VDLY (V) Delay Capacitor Capacitance CDLY (F)
52
53
SI-3000P Series
SI-3000P Series
3-Terminal, Dropper Type
Features
TO-3P package 3-terminal regulator
Output current: 2.0A
Wide range of DC input voltage
Built-in foldback overcurrent protection circuit
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
54
SI-3000P Series
A foldback type overcurrent protection circuit is built into the IC regulator. Therefore, avoid using it for the following applications as it may cause
starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage
15.60.3
4.8max.
13.60.2
2.0
9.60.2 2.0max.
19.90.3
3.20.1
14.90.3
4.0
a
b a. Part Number
b. Lot Number
+0.2
2.0 0.1
20.0min.
Pin Arrangement
3.5
+0.2
3.0 0.1
q VO
+0.2 +0.2
1.05 0.1 0.65 0.1
w VIN (backside of case)
5.450.1 5.450.1 1.7
+0.2 e GND
0.3
q w e
55
SI-3000P Series
Block Diagram
Tr1
2 1
R2 R1
M1
r10
r2 r3 r8
R3
Tr5 Tr12
d3
r4
Tr6 Tr7
d1 r5
d5 Tr8 C1
d2 Tr9 r9 R4
d6
d7
r6 r7
3
GND GND Note 1: Connect a 47F to 100F capacitor to both sides of the
load if the wiring between the output terminal and the
load is long.
Note 2: An isolation type diode is provided from input to ground
and also from output to ground. These may be destroyed
if the device is reverse biased. In this case, use a diode
with low VF to protect them.
Note 3: The output voltage may not be adjusted by raising the
ground voltage (using a diode or resistor).
Ta-PD Characteristics
24 Without Mica
2002002 (2.3C/W) With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
20 Unit: mm
16
1001002 (5.2C/W)
12
75752 (7.6C/W)
8
4
Without heatsink
0
20 0 25 50 75 100
Ambient Temperature Ta (C)
56
SI-3000P Series
Typical Characteristics
(Ta=25C)
15
3.0 5.04
10
5.03
2.5
5.02
5
2.0
5.01
1.5 5.00 0
0 0.5 1.0 1.5 2.0 2.5 3.0 40 20 0 20 40 60 80 100 0 2 4 6 8 10 12 14 16
Output Current lO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
6 12 25
Output Voltage Vo (V)
5 10
lO=0A 20
0.5A lO=0A
4 8 1A 0.5A
1.5A 15 1A
lO=0A 2A 1.5A
3 6
0.5A 2A
1A 10
2 2A 4
1 2 5
0 0 0
0 1 2 3 4 5 6 7 8 9 10 11 0 5 10 15 20 0 5 10 15 20 25 30 35 40
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
25V
6 12
35V
25
30
VIN 33
=15
V
VI
Output Voltage VO (V)
V V
Output Voltage VO (V)
Output Voltage VO (V)
5 10 N= 35V
19V 27
20 V
5V 10V
4 8. 8
N=
VI 11.5V
15
3 6
10
2 4
2 5
1
0 0 0
0 1 2 3 4 0 1 2 3 4 5 6 7 8 0 1 2 3 4 5 6 7 8
Output Current lO (A) Output Current lO (A) Output Current lO (A)
57
SI-3000V Series
SI-3000V Series
3-Terminal, Low Dropout Voltage Dropper Type
Features
TO-3P package 3-terminal regulator
Output current: 2.0A
Low dropout voltage: VDIF1V (at IO=2.0A)
Built-in foldback overcurrent protection circuit
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
58
SI-3000V Series
*: A foldback type overcurrent protection circuit is built into the IC regulator. Therefore, avoid using it for the following applications as it may cause
starting errors:
(1) Constant current load (2) Plus/minus power (3) Series power (4) VO adjustment by raising ground voltage
15.60.3
4.8max.
13.60.2
2.0
9.60.2 2.0max.
19.90.3
3.20.1
14.90.3
4.0
a
b a. Part Number
b. Lot Number
+0.2
2.0 0.1
20.0min.
Pin Arrangement
3.5
+0.2
3.0 0.1
q GND
+0.2 +0.2
1.05 0.1 0.65 0.1
w VO (backside of case)
5.450.1 5.450.1 1.7
+0.2
0.3
e VIN
15.80.2
Plastic Mold Package Type (TO-3P)
Flammability: UL94V-0
Weight: Approx. 6g
q w e
59
SI-3000V Series
Block Diagram
Tr1
3 2
R2 R1 R4
M1
Amp.
Drive
Reg.
Protection
VREF
R5
R3
1
Ta-PD Characteristics
24 Without Mica
2002002 (2.3C/W) With Silicon Grease
Heatsink: Aluminum
Power Dissipation PD (W)
20 Unit: mm
16
1001002 (5.2C/W)
12
75752 (7.6C/W)
8
4
Without heatsink
0
20 0 25 50 75 100
Ambient Temperature Ta (C)
60
SI-3000V Series
Typical Characteristics
(Ta=25C)
0.6
40
0.4 5.00
30
4.98
20 lo=2.0A
0.2
1.5A
4.96
10 1.0A
0.5A
0 4.94 0 0A
0 0.5 1.0 1.5 2.0 60 40 20 0 20 40 60 80 100 120 140 0 5 10 15 17.5
Output Current lO (A) Ambient Temperature Ta (C) Input Voltage VIN (V)
14 16
5
14
Output Voltage Vo (V)
12
Output Voltage VO (V)
10
to
to
.5
3 8
=2
o
t 8 7 .5
RL
=6 L=
6 RL R
2 6
4
4
1
2 2
0 0 0
0 1 2 3 4 5 6 7 0 2 4 6 8 10 12 14 16 0 2 4 6 8 10 12 14 16 18
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
14 16
5 20V
16V
10V 14
Output Voltage Vo (V)
12
Output Voltage VO (V)
Output Voltage Vo (V)
20V
V
VIN=
6
8V
=13
1
4 12
10
VIN
10
3 8
8
6V
6
5V
N=
2 1 6
VI
4
4
1 2 2
0 0 0
0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7
Output Current lo (A) Output Current lo (A) Output Current lO (A)
61
62
Switching Type - Application Note
Temperature and Reliability Fastening Torque
The reliability of an IC is highly dependent on its operating tempera- SI-8000E
ture. Design should pay particular attention to ensuring ample space 0.588 to 0.686[Nm] (6.0 to 7.0[kgfcm])
SI-8000S
for radiating heat.
Be sure to apply silicon grease to the IC before attaching a heatsink,
and to secure it firmly to the heatsink. Allow sufficient margine which Recommended Silicon Grease
designing the heatsink.
Shin-Etsu Chemical Co., Ltd.: G746
Other important items to be considered regarding heat radiation in-
clude air convection during operation. GE Toshiba Silicone Co., Ltd.: YG-6260
The reliability of peripheral components such as capacitors and coils Dow Corning Toray Silicone Co., Ltd.: SC102
is closely related to temperature. A high operating temperature may Please be careful when selecting silicone grease since the oil in some
reduce the service life. Exceeding the allowable temperature may burn grease may penetrate the product, which will result in an extremely
the coils or damage capacitors. It is important to make sure that the short product life.
temperature of output smoothing coils and input/output capacitors do
not exceed their allowable levels during operation. Allow for variation
in the ratings of the coils and minimize heat emission as far as pos- Others
sible. (For peripheral components, refer to the user manuals.)
Parallel operation can not be performed for increasing current.
This type IC regulators can not be used for boosting current and
Internal Power Dissipation raising voltage.
63
SAI Series
SAI Series
Surface-Mount, Separate Excitation Switching Type
Features
Surface-mount package
Output current: 0.4 to 0.5A
High efficiency: 75 to 89%
Requires only 4 external components
Phase correction and output voltage adjustment performed internally
Built-in reference oscillator (60kHz)
Built-in overcurrent and thermal protection circuits
Applications
Power supplies for telecommunication equipment
Onboard local power supplies
Lineup
Part Number SAI01 SAI02 SAI03 SAI04 SAI06
VO(V) 5.0 3.3 12.0 15.0 9.0
IO(A) 0.5 0.4
64
SAI Series
2 SW
3VOS
0.25
0.2
max.
4 a. Part Number
4.32
2.54
a b
4.7
.GND 1VIN
b. Lot Number
0.15
0.2
+0.15
1.4
0.89
max. 0.2
6.8 3.6
max. Pin Arrangement
0.5 4.0
A 8.0 q VIN
0.2
6.3
w SWOUT
e VOS
+0.15
0.3 0.05
r GND
0.25
Drive + D1 +
C1 GND C2
Comp.
100F 4 SFPB54 330F
(Sanken)
3 VOS
Amp.
GND GND
VREF
4
GND
65
SAI Series
Ta-PD Characteristics
100 VO
0.8 PD=VOIO 1 VFIO 1
Glass epoxy VIN
0.7
substrate
(95691.2)
No airflow
Power Dissipation PD (W)
0.6 The efficiency depends on the input voltage and the out-
0.5 put current. Thus, obtain the value from the efficiency
graph on page 67 and substitute the percentage in the
0.4
formula above.
0.3
Application
66
SAI Series
Typical Characteristics
0.1A 90 5.2
5
7V
Output Voltage VO (V)
Efficiency (%)
4
VIN=33V
IO =
A
0.5
V
70 10 5.0 10V
20V
3
7V
60 4.9
25V
33V
2
50 4.8
1 40 4.7
0 0 0
0 2 4 6 8 10 0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
90 5.2 5
5
Output Voltage VO (V)
Output Voltage VO (V)
70 5.0
=7
3
VIN
3
33
60 4.9
f
2 2
50 4.8
1 1
40 4.7
0 0 00 0
50 0 50 100 150 0.5 1.0 1.5 2.0 0 50 100 150 200
Ambient Temperature Ta (C) Output Current IO (A) Case Temperature TC (C)
12 90 12.2
5V
4A
0A
=1
Output Voltage VO (V)
IN
10 80 V
V 12.1
Efficiency (%)
0.2A 33
V
VIN=33V
24
8 70 24V
12.0 20V
6 60
15V
11.9
4 50
2 40 11.8
0 0 0
0 5 10 15 20 0 0.1 0.2 0.3 0.4 0 0.1 0.2 0.3 0.4
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
67
SI-8000E Series
SI-8000E Series
Full-Mold, Separate Excitation Switching Type
Features
Compact full-mold package (equivalent to TO220)
High efficiency: 80 to 88%
Requires only 4 external components
Phase correction and output voltage adjustment performed internally
Built-in reference oscillator (60kHz)
Built-in overcurrent and thermal protection circuits
Applications
Power supplies for telecommunication equipment
Onboard local power supplies
Lineup
Part Number SI-8050E SI-8090E SI-8120E
VO(V) 5.0 9.0 12.0
IO(A) 0.6
68
SI-8000E Series
3.20.2
4.20.2
10.00.2 2.80.2
0.5
4.00.2
7.90.2
16.90.3
a
(17.9)
b a. Part Number
2.60.1 b. Lot Number
(2.0)
5.00.6
Pin Arrangement
0.950.15
q VIN
+0.2
w SWOUT
(4.6)
0.85 0.1
(8.0)
e GND
+0.2
0.45 0.1 r VOS
P1.70.74=6.80.7 3.90.7 (4.3) t N.C
8.20.7
Plastic Mold Package Type
Flammability: UL94V-0
Weight: Approx. 2.3g
1 2 3 4 5
69
SI-8000E Series
5V : 200H
VIN 1 2 SWOUT 9V,12V: 300H
OCP L1
VIN 2 VO
1
Reg. VIN SWOUT
Ta-PD Characteristics
100 VO
PD=VOIO 1 VFIO 1
15
VIN
Infinite heatsink
With Silicon Grease
Heatsink: Aluminum
The efficiency depends on the input voltage and the out-
Power Dissipation PD (W)
10
graph on page 71 and substitute the percentage in the
0
2 00
10
formula above.
2
0
1
m
00
m
2
(2
mm
.3
(5 VO : Output voltage
C
75 .2
7
/W
5 5 C/
)
Application
70
SI-8000E Series
Typical Characteristics
90
5
0.1A
5.1
IN
V V 4
10 0V
0A
0.3A
A
2
0.6
70 V VIN=40V
IO=
30 V
40 3 5.0
20V
60
10V
2 7V
50
4.9
40 1
0 0 4.8
0 0.1 0.2 0.3 0.4 0.5 0.6 0 2 4 6 8 10 0 0.1 0.2 0.3 0.4 0.5 0.6
Output Current IO (A) Input Voltage VIN (V) Output Current IO (V)
5 90 5.2 5
80 5.1
4 4
20V VO
70 5.0
V
=7
3 3
V
Frequency f (kHz)
40
VIN
60 4.9
f
2 2
50 4.8
1 1
40 4.7
0 0 0 0
0 0.5 1.0 1.5 2.0 0 0 50 100 150 0 50 100 150 200
Output Current IO (V) Ambient Temperature Ta (C) Case Temperature TC (C)
71
SI-8000S Series
SI-8000S Series
Full-Mold, Separate Excitation Switching Type
Features
Compact full-mold package (equivalent to TO220)
Output current: 3.0A
High efficiency: 79 to 91%
Requires only 4 external components
Phase correction and output voltage adjustment performed internally
Built-in reference oscillator (60kHz)
Built-in overcurrent and thermal protection circuits
Built-in soft start circuit (output ON/OFF control)
Applications
Power supplies for telecommunication equipment
Onboard local power supplies
Lineup
Part Number SI-8033S SI-8050S SI-8090S SI-8120S SI-8150S
VO(V) 3.3 5.0 9.0 12.0 15.0
IO(A) 3.0
72
SI-8000S Series
3.20.2
4.20.2
10.00.2 2.80.2
0.5
4.00.2
7.90.2
16.90.3
c a. Part Number
(17.9)
a
b
b. Lot Number
2.60.1 c. Logo Mark
(2.0)
5.00.6
Pin Arrangement
0.15
0.95
q VIN
+0.2
w SWOUT
(4.6)
0.85 0.1
(8.0)
e GND
+0.2
0.45 0.1
r VOS
P1.70.74=6.80.7 3.90.7 (4.3) t S.S
8.20.7
Plastic Mold Package Type
Flammability: UL94V-0
Weight: Approx. 2.3g
1 2 3 4 5
73
SI-8000S Series
Block Diagram
VIN 1 2 SWOUT
Reg. OCP
OSC Reset
Drive
Comp. TSD
4 VOS
Amp.
VREF
5 S.S. 3 GND
L1
VIN 2 VO
1
VIN SWOUT
C1,2 : 1000F
SI-8000S D1
+ + L1 : 150H
C1 C2
VOS D1 : RK46(Sanken)
4
S.S GND
5 3
GND GND
Ta-PD Characteristics
100 VO
PD=VOIO 1 VFIO 1
20
VIN
Infinite heatsink
With Silicon Grease
Heatsink: Aluminum
The efficiency depends on the input voltage and the out-
Power Dissipation PD (W)
15
2002002mm put current. Thus, obtain the value from the efficiency graph
(2.3C/W)
on page 75 and substitute the percentage in the formula
1001002mm above.
10 (5.2C/W)
74
SI-8000S Series
Typical Characteristics
90
8 5.10
Output Voltage VO (V)
VIN=40V
Efficiency (%)
20V
6 10V 5.05
7V VIN=40V
70
20V
0A
4 5.00
IO=
10V
1A
60
3A
7V
2 4.95
50
0 0 0
0 2 4 6 8 10 12 0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
(VIN=20V,IO=1A) (VIN=20V,IO=0A)
Efficiency (%) Frequency f (kHz)
90 5.10 8 8
Output Voltage VO (V)
80 5.05 6 6
VO
70 5.00 4 4
VIN=7V
40V
0 0 0 0
50 25 0 25 50 75 100 0 1 2 3 4 5 6 50 75 100 125 150 175 200
Ambient Temperature Ta (C) Output Current IO (A) Ambient Temperature Ta (C)
VIN=40V
90
20 12.2
15V
Output Voltage VO (V)
24V
80
Efficiency (%)
15 12.1
70 VIN=40V
10 12.0 24V
60
15V
A
=0
5 11.9
IO
1A
50
3A
0 0 0
0 5 10 15 20 25 30 0 0.5 1.0 1.5 2.0 2.5 3.0 0 0.5 1.0 1.5 2.0 2.5 3.0
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
75
SI-8000S Series
GND GND
Inductance
100%
(2) Input capacitor
Place the input capacitor C1 and output capacitor C2 as close to
the IC as possible. Since a large current flows through the lead
50% wires of the input and output capacitors to charge and discharge
them quickly, minimize the lead wire length. The pattern around
the capacitors should also be minimized.
76
SI-8000S Series
D1
GND
+ C1
The output voltage adjustment resistance REX is calculated
VOUT
C2 as follows:
VO'VS
REX=
IVS
GND
VIN VS : Output voltage of product
VO' : Adjusted output voltage
Top view (with part names) IVS : Inflow current to Vs terminal
Applications the value REX is not compensated for temperature. The Vs value
fluctuates by up to 20% depending on the IC product. Since the
output voltage fluctuates more, a semi-fixed resistor is necessary
1. Soft Start for accurate output voltage adjustment. If Vs and REX are constant,
Connecting a capacitor to terminal no. 5 permits a soft start at power- the range of output voltage fluctuation can be expressed as follows:
on. Delay time Td and rise time Ts can roughly be calculated as VO'VS
VO'(%)= 20
shown below. (However, the values may slightly vary in an actual VO'
application.) If the capacitance of C3 is increased, it takes longer to VO': Adjusted output voltage
discharge C3 after VIN is turned off. Therefore, it is recommended to
set the value to 10F or less. When not using the soft start function, (2) Variable output voltage with two external resistors
keep terminal no. 5 open.
0.7C3
T d= (sec) L VO
20106 2
4.845C3
Ts= (sec) SI-8000S IREX1
VIN20106 REX1
C2
4 VS
3
SI-8000S IVS
VIN REX2
5
GND
S. S.
C3
VO The output voltage adjustment resistances REX1 and REX2 are
Td TS calculated as follows:
2. Output ON/OFF control VO'VS
REX1=
Output can be turned on and off by using the soft start terminals. SIVS
Set the soft start terminal voltage to VSSL (0.2V typ.) or less to stop VS
REX2=
output. To switch the potential at the soft start terminals, drive the (S-1)IVS
open collector of the transistor. Since the discharge current from C3 S:Stability factor
flows to the ON/OFF control transistor, limit the current for protec-
tion. The SS terminal is pulled up to the power supply in the IC and Bypassing the current to REX2 improves the temperature charac-
no external voltage can be applied. teristics and voltage fluctuation ranges more than the method of
(1). Stability factor S indicates the ratio of REX1 to Vs terminal
inflow current. Increasing the S value improves the fluctuations
SI-8000S SI-8000S
of the temperature characteristics and output voltage. (Usually 5
5 5
to 10)
S. S. S. S.
If the Vs and REX values are constant, the output voltage fluctua-
C3
tion range can be calculated as follows:
20 VO'VS
VO'(%)=
ON/OFF S. S + ON/OFF S VO'
77
SI-8200L/8300L Series
SI-8200L/8300L Series
Self Oscillating Switching Type with Coil
Features
Integrated switching IC and coil construction
Requires 2 external components only
Low switching noise
Heatsink not required
Applications
Telephone power supplies
Onboard local power supplies
Lineup
Part Number SI-8201L SI-8203L SI-8211L SI-8213L SI-8301L
VO(V) 5 12 5 12 5
IO(A) 0.4 0.35 0.3 0.28 1.0
78
SI-8200L/8300L Series
SI-8201L8203L SI-8211L8213L
20.5max.
a a. Part Number a a. Part Number
b
13
b. Lot Number b b. Lot Number
t GND Open Air Type Open Air Type
VO q 0.5
14.5 Weight: Approx. 5.1g VO q t GND Weight: Approx. 5.9g
Terminal 1 marking 20.5max.
Terminal 1 marking
15
0.6
13.5max.
13.2
0.2
10
;;;;;
;;;;;
;;;;;
;;;;;;;
2 2
5.5
0.8
0.6
0.8max.
47
SI-8301L
VIN LIN
y r
0.1
a b
26
a. Part Number
SK
b. Lot Number
Open Air Type
q w e Weight: Approx. 14.5g
VO NC GND
0.1
26
Terminal 1 marking
3.7 18
0.6 2
4 18
79
SI-8200L/8300L Series
Block Diagram
SI-8201L8203L/SI-8301L SI-8211L8213L
LIN L1 LIN L1
VIN VO VIN VO
Tr1
Tr1
DI Tr2 DI
Vref
Amp. Drive
Drive Amp.
SI-8200L SI-8300L
VIN VIN VO VO VIN VIN VO VO
DC Input GND LIN
DC Input
+ + NC GND LIN
+ +
C1 C2 C1 C2
220F 470F 470F 470F
Ta-PD Characteristics
SI-8201L
8203L SI-8301L
1.5 3.0 100
PD=VOIO 1
Power Dissipation PD (W)
Power Dissipation PD (W)
SI-8211L
8213L
1.0 2.0
VO :Output voltage
IO :Output current
:Efficiency (%)
0.5 1.0
Caution
1. A low-impedance capacitor suitable for switching applications must be used for the external capacitor and must be connected as close to the
IC as possible in order to assure low ripple voltage and stable switching operation.
2. The SI-8200L and 8300L series do not have a built-in overcurrent protection circuit. Thus, avoid short-circuit conditions that may cause an
overcurrent.
3. The SI-8300L series may not start up if the input voltage rises too rapidly.
Do not use the SI-8300L series in applications where the input terminal, pin6, is opened and closed directly in a state where the input voltage
is already applied.
4. Terminals LIN and NC in the connection diagram must be left unconnected to other circuits.
5. The IC's metalic heatsink is electrically floating. Do not connect it to GND or any other circuit.
6. Since the SI-8200L and 8300L series have an open-package construction, they can only be used in specific environments. Verify the operating
environment and use the IC within the conditions indicated in the reliability data.
80
SI-8200L/8300L Series
Typical Characteristics
(Ta=25C)
12
5 5
10
4 4
IO=0.4A (C.C)
8
RL=12.5
3 3
lO=0A
RL=34.3
lO=0A
2 2
IO=0.35A (C.C)
4
)
A
(C.C
lO=0
.3A
6.7
1 2 1
=1
IO=0
RL
0 0 0
0 5 10 15 20 0 5 10 15 20 0 5 10 15 20
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
Efficiency (%)
35V 30V 35V
40
Efficiency (%)
40V 60 50 55V
50
50 40
40
40 30
30
30 20
20
20 10
10
0 0
0 0 0.1 0.2 0.3 0.4
0 0.05 0.10 0.15 0.20 0.25 0.30 0.35 0.40 0.45 0 0.1 0.2 0.3 0.4
Output Current lO (A) Output Current lO (A) Output Current lO (A)
SI-8213L SI-8301L
Output Voltage Output Voltage
14 7
12 6
lO=0A
Output Voltage Vo (V)
Output Voltage VO (V)
10 5
8 4 RL=5.1
IO=1A (C.C)
6 3
4 2
)
.C
(C
1
8A
2
0A
0.2
43
lO = L=
I O=
R
0 0
0 5 10 15 20 0 5 10 15 20
Input Voltage VIN (V) Input Voltage VIN (V)
40
Efficiency (%)
60
60
50
50
40
40
30
30
20
20
0
0 0.1 0.2 0.3 0.4 00 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1
Output Current lO (A) Output Current lO (A)
81
SI-8400L/8500L Series
SI-8400L/8500L Series
Separate Excitation Switching Type with Coil
Features
Integrated switching IC and coil construction
Requires 2 external components only
Low switching noise
Heatsink not required
Built-in overcurrent and thermal protection circuits
Built-in soft start circuit (Output ON/OFF control)...SI-8500L Series
Applications
Telephone power supplies
Onboard local power supplies
Lineup
Part Number SI-8401L SI-8402L SI-8403L SI-8405L SI-8501L SI-8502L SI-8503L SI-8504L SI-8505L
VO(V) 5.0 12.0 3.3 15.0 5.0 12.0 3.3 9.0 15.0
IO(A) 0.5 0.4 0.5 0.4 1.0
Ratings
Parameter Symbol Unit
SI-8501L SI-8502L SI-8503L SI-8504L SI-8505L
DC Input Voltage Range VIN 7 to 33 15 to 33 5.3 to 33 12 to 33 18 to 33 V
Output Current Range IO 0 to 1.0 A
Operating Temperature Range Top 20 to +85 C
82
SI-8400L/8500L Series
(Ta=25C)
Ratings
Parameter Symbol SI-8501L SI-8502L SI-8503L SI-8504L SI-8505L Unit
min. typ. max. min. typ. max. min. typ. max. min. typ. max. min. typ. max.
VO 4.80 5.00 5.20 11.40 12.00 12.60 3.17 3.30 3.43 8.55 9.00 9.45 14.25 15.00 15.75
Output Voltage V
Conditions VIN=20V, IO=0.5A VIN=24V, IO=0.5A VIN=15V, IO=0.5A VIN=21V, IO=0.5A VIN=25V, IO=0.5A
83 89 79 87 90
Efficiency %
Conditions VIN=20V, IO=0.5A VIN=24V, IO=0.5A VIN=15V, IO=0.5A VIN=21V, IO=0.5A VIN=25V, IO=0.5A
f 60 60 60 60 60
Switching Frequency kHZ
Conditions VIN=20V, IO=0.5A VIN=24V, IO=0.5A VIN=15V, IO=0.5A VIN=21V, IO=0.5A VIN=25V, IO=0.5A
VOLINE 70 130 70 130 50 80 70 130 70 130
Line Regulation mV
Conditions VIN=10 to 30V, IO=0.5A VIN=18 to 30V, IO=0.5A VIN=8 to 30V, IO=0.5A VIN=15 to 30V, IO=0.5A VIN=21 to 30V, IO=0.5A
VOLOAD 30 55 30 55 20 45 30 55 30 55
Load Regulation mV
Conditions VIN=20V, IO=0.2 to 0.8A VIN=24V, IO=0.2 to 0.8A VIN=15V, IO=0.2 to 0.8A VIN=21V, IO=0.2 to 0.8A VIN=25V, IO=0.2 to 0.8A
Temperature Coefficient of Output Voltage VO/Ta 0.5 1.5 0.5 1.0 1.5 mV/C
Switching Ripple Vr 45 30 15 25 30
mVp-p
Voltage (C2=470F) Conditions VIN=20V, IO=0.5A VIN=24V, IO=0.5A VIN=15V, IO=0.5A VIN=21V, IO=0.5A VIN=25V, IO=0.5A
Overcurrent Protection IS1 1.1 1.1 1.1 1.1 1.1
A
Starting Current Conditions VIN=18V VIN=24V VIN=12V VIN=21V VIN=25V
83
SI-8400L/8500L Series
SI-8400L SI-8500L
VIN LIN
y r
e LIN
VIN r a. Part Number a. Part Number
120.5
a
b. Lot Number b. Lot Number
0.1
b
a b
26
Open Air Type Open Air Type
w GND
Vo q 14.5
0.5
Weight: Approx. 5.1g SK Weight: Approx. 14.5g
Terminal 1 marking
q w e
VOUT SS GND
0.6
0.1
26
13.2
0.2
Terminal 1 marking
10
;;;;
;;;;
;;;;;;
;;;
0.6
0.8max.
4.7
18
3.7
0.6 2
4 18
Block Diagram
SI-8400L SI-8500L
3 LIN 4 LIN
4 L1 1 6 L1 1
MIC1 MIC1
VIN VO VIN VO
Reg. OCP Reg. OCP
Amp. Amp.
VREF VREF
Pin compatible with SI-8200L C3 is necessary only for using soft start function.
Pin compatible with SI-8300L
84
SI-8400L/8500L Series
Ta-PD Characteristics
2.0
VO :Output voltage
1.0
IO :Output current
:Efficiency (%)
start terminal, drive the open collector of the transistor. Since the
discharge current from C3 flows to the ON/OFF control transistor, limit
the current for protection. The SS terminal is pulled up to the power VO. ON/OFF Soft start Soft start +VO ON/OFF
supply in the IC and no external voltage can be applied.
Caution
1. Allocation of Components
For the best operating environment, the ground should be a single ground line at the GND terminal (terminal 2 on the SI-8400L, terminal 3 on
the SI-8500L), and the wiring from C1 and C2 to ground should be as short as possible.
2. Capacitors C1 and C2
1) They must satisfy the breakdown voltage and allowable ripple current.
Exceeding the ratings of these capacitors or using them without derating shortens their service lives and may also cause abnormal
oscillation of the IC.
2) C2 must be a low-impedance type capacitor to ensure minimum ripple voltage and stable switching operation.
3) C3 (SI-8500L only) is a capacitor for soft start. When not using soft start, leave terminal 2 open. It is pulled up inside the IC.
3. Terminals LIN and NC in the connection diagram must be left unconnected to other circuits.
4. The IC's metalic heatsink is electrically floating. Do not connect it to GND or any other circuit.
5. Since the SI-8400L and 8500L series have an open-package construction, they can only be operated in specific environments. Verify the
operating environment and use the conditions indicated in the reliability data.
85
SI-8400L/8500L Series
5 90 5.2
0.1A
20V
4 25V 5.1
Efficiency (%)
80 33V
A
VIN 20V
=0
0.5
10V VIN=33V
7V
IO
3 10V 7V 5.0
70 10V
0.3A
20V 7V
2 4.9
60 25V
33V
1 4.8
50
0 0 0
0 2 4 6 8 10 0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
90 5.2 5 5
20V
Output Voltage VO (V)
80 5.1
4 4
V
70 5.0
=7
VO 3
V
3
VIN
33
60 4.9
f 2 2
50 4.8
1 1
40 4.7
0 0
0 40 20 0 20 40 60 80 100 0 0 0.5 1.0 1.5 2.0 0 50 100 150 200
Ambient Temperature Ta (C) Output Current IO (A) Case Temperature TC (C)
12 90 12.2
0.2A
V
15
10
V V N=
12.1
Efficiency (%)
80
33 24 VI
VIN=33V
0A
8
4A
IO=
24V
0.
70 12.0
20V
6
15V
60 11.9
4
50 11.8
2
0 0 0
0 5 10 15 20 0 0.1 0.2 0.3 0.4 0 0.1 0.2 0.3 0.4
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
86
SI-8400L/8500L Series
6 90 5.10
7V
VIN=
Output Voltage VO (V)
Efficiency (%)
VIN =33V
0A
V
0.5A 33 20V
IO =
4 70
1A
5.00
15V
60 7V
3 4.95
2 50 4.90
1 40 4.85
0 0 0
0 5 10 15 20 0 0.25 0.5 0.75 1 0 0.25 0.5 0.75 1
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
90 5.10 6 6
Output Voltage VO (V)
Output Voltage VO (V)
70 5.00 4 4
33V
VO
f
VIN=7V
60 4.95 3 3
20V
50 4.90 2 2
40 4.85 1 1
0 0 0 0
40 0 40 80 120 0 1 2 3 4 0 40 80 120 160
Ambient Temperature Ta (C) Output Current IO (A) Ambient Temperature Ta (C)
5V 12.2
12 90 =1
VIN
V
33
Output Voltage VO (V)
Output Voltage VO (V)
0.5A
V
80 12.1
24
10
24V
Efficiency (%)
VIN=33V
12.0
0A
8 70 18V
IO=
1A
15V
6 60 11.9
4 50 11.8
2 40 11.7
87
SI-8800L/8900L Series
SI-8800L/8900L Series
Separate Excitation Switching Type with Transformer
Features
Integrated switching IC and transformer construction
Requires only input/output and soft start capacitors as external components
Low switching noise
Heatsink not required
Built-in overcurrent protection circuit (+5V)
Both plus and minus output models available (SI-8811L, SI-8911L)
Applications
Telephone power supplies
Onboard local power supplies
Lineup
Ch1 Ch2
Part Number
VO(V) IO(A) VO(V) IO(A)
SI-8811L +5 0.45 5 0.05
SI-8911L +5 0.3 5 0.1
SI-8921L/8922L +5 0.6
88
SI-8800L/8900L Series
o y
0.2
0.2
a
19
22
b a. Part Number
SK b. Lot Number
;;;;;;;;;;
0.1
1
;;;;;;;;;;;
(16.5)
0.6
0.8max.
(4P3.175=12.7)
4
89
SI-8800L/8900L Series
Block Diagram
SI-8811L SI-8911L
VIN 3 9
(+) VO1
VIN VO1
1 9 1 8
Tr1
3
Amp. T1 Amp. T1
Vref GND Vref GND
8 7
OSC PWM Drive OSC PWM Drive Tr1
VO2 VO2
VIN Start OCP Reg. 7 Start OCP Reg. 6
()
4
2 S.S 5 4
2 S.S 5 6
SI-8921L/8922L
7
VIN VO
1 6
3
Amp. T1
Vref
2 S.S
VIN
1
(+)
C1(for smoothing VIN) : 35V/470F
2 9 VO1
+ + C2(for soft start) : 16V/10F
C4
C1 + SI-8811L C3(for smoothing VO2Reg input) : 10V/220F
3 8 GND
C2 +
C5
C4(for smoothing VO1) : 16V/1200F
VIN
4 7 VO2 C5(for smoothing VO2) : 10V/47F
()
+
5 6 C3
C1,2,3,5 : Nippon Chemi-con SME Series or equivalent
C4 : Nippon Chemi-con SXE Series or equivalent
VIN 1
GND
C1,2,3,5 : Nippon Chemi-con SME Series or equivalent
C4 : Nippon Chemi-con SXE Series or equivalent
VIN 1
C1(for smoothing VIN) : 63V/180F
2 SI-8921L 7 C2(for soft start) : 10V/22F
+ C3(for smoothing VO) : 10V/1200F
3 SI-8922L 6 VO
C1 + +
C3
C2
C1,2 : Nippon Chemi-con SME Series or equivalent
4 5 GND
C3 : Nippon Chemi-con SXE Series or equivalent
GND
90
SI-8800L/8900L Series
Ta-PD Characteristics
SI-8811L 100
SI-8921L PD=VOIO 1
1.5 1.5 8922L
SI-8911L
VO :Output voltage
1.0 1.0
IO :Output current
:Efficiency (%)
0.5 0.5
The efficiency depends on the input
8922L
SI-8921L
SI-8911L
voltage and the output current. Thus,
obtain the value from the efficiency
0 0
0 25 50 75 100 0 25 50 75 100 graphs on p.92 and substitute the
Ambient Temperature Ta (C) Ambient Temperature Ta (C)
percentage in the formula above.
Caution
1. A low-impedance capacitor suitable for switching applications must be used for the external capacitor and must be connected as close to the
IC as possible in order to assure low ripple voltage and stable switching operation.
2. The SI-881L/8911L series does not have a built-in overcurrent protection circuit on VO2(5V). Thus, avoid short-circuit conditions that may
cause an overcurrent.
3. Do not connect VIN() of SI-8811L to GND. The overcurrent protection circuit may not work if they are connected.
4. Terminals left unconnected in the connection diagram must not be connected to other circuits.
5. The IC's metallic heatsink is electrically floating. Do not connect it to GND or any other circuit.
6. Since the SI-8800L and 8900L series have an open-package construction, they can be operated in specific environments. Verify the operating
environment and use the IC within the conditions indicated in the reliability data.
91
SI-8800L/8900L Series
Typical Characteristics
(Ta=25C)
4 4 5
lO1=50mA lO2 =0mA 0.3A
lO1
0 VIN 0 VIN 3
2 4 6 8 10 12 14 16 18 20 (V) 5 10 15 20 25 30 35 40 (V)
6 6 0
Input Voltage VIN (V) 0 5 10 15 20 25 30 35 40 45
Input Voltage VIN (V)
Input Voltage VIN (V)
Efficiency (%)
Efficiency (%)
60 V V
40 24
70
50
50
65 40
40
30
60
30
20
IO2 = 50mA constant
IO2 = 100mA constant
0 0 0
0 50 100 150 200 250 300 350 400 450 500 0 50 100 150 200 250 300 350 400 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8
Output Current 1 lO1 (A) Output Current 1 lO1 (A) Output Current lO (A)
SI-8922L
Output Voltage
8
7
Output Voltage VO (V)
5
0.5A
4
0.6A
IO=0.4A
00 10 20 30 40
Input Voltage VIN (V)
Efficiency Characteristics
80
VIN=55
V
70 48V
40V
30V
60 24V
Efficiency (%)
50
40
30
20
92
Multi-Output Type - Application Note
Heat Radiation and Reliability Fastening Torque
The reliability of an IC is highly dependent on its operating tempera- STA800M Series (when using a spring)
ture. Design should pay particular attention to ensuring ample space 0.588 to 0.784 [Nm](6.0 to 8.0[kgfcm]
for radiating heat. SLA3000M Series
Be sure to apply silicon grease to the IC before attaching a heatsink, 0.588 to 0.784 [Nm](6.0 to 8.0[kgfcm]
and to secure it firmly to the heatsink.
Other important items to be considered regarding heat radiation in-
clude air convection during operation. Recommended Silicon Grease
The reliability of peripheral components such as capacitors and coils Shin-Etsu Chemical Co., Ltd.: G746
is closely related to temperature. A high operating temperature may GE Toshiba Silicone Co., Ltd.: YG-6260
reduce the service life. Exceeding the allowable temperature may Dow Corning Toray Silicone Co., Ltd.: SC102
burn the coils or damage capacitors. It is important to make sure that Please be careful when selecting silicone grease since the oil in some
the temperature of output smoothing coils and input/output capaci- grease may penetrate the product, which will result in an extremely
tors do not exceed their allowable levels during operation. Allow for short product life.
variation in the ratings of the coils and minimize heat emission as far
as possible. (For peripheral components, refer to the user manuals.)
Heatsink Design
The maximum junction temperature Tj(max) given in the absolute maxi-
mum ratings is specific to each product type and must be strictly
observed. Thus, thermal design must consider the conditions of use
which affect the maximum power dissipation PD(max) and the maxi-
mum ambient temperature Ta(max).
To simplify thermal design, the relationship between these two pa-
rameters has been presented in a graph, the Ta-PD characteristic
graph. Thermal design should include these steps:
1. Obtain the maximum ambient temperature Ta(max).
2. Obtain the maximum power dissipation PD(max).
3. Look for the intersection point on the Ta-PD characteristic graph
and determine the size of the heatsink.
The size of the heatsink has now been obtained. However, in actual
applications, a 10 to 20% derating factor is introduced. Moreover, the
heat dissipation capacity of a heatsink highly depends on how it is
mounted. Thus, it is recommended to measure the heatsink and case
temperature in the actual operating environment.
The Ta-PD characteristics for each product type are provided for ref-
erence purposes.
93
STA801M/802M
STA801M/802M
2-Output Separate Excitation Switching Type
Features
2 regulators combined 1 package
Compact inline package
Output current (0.5A 2 output)
Output voltage of Ch2 selectable from 4 levels.
Built-in flywheel diode (Schottky barrier diode)
Requires only 7 external components (2 outputs)
Phase correction and output voltage adjustment performed internally
Built-in reference oscillator (125kHz) - Compact choke coil can be used
due to high frequency (compared to existing Sanken product)
Built-in overcurrent and thermal protection circuits
Built-in soft start circuit (Output ON/OFF control)
Applications
For BS and CS antenna power supplies
For stabilization of the secondary stage of switching power supplies
Electronic equipment
Lineup
Output Voltage (V)
Part Number
Ch1 Ch2(Select one output)
STA801M 5 9.0 / 11.5 / 12.1 / 15.5
STA802M 9 9.1 / 11.7 / 12.1 / 15.7
94
STA801M/802M
*Efficiency indicates the value when only one channel is active. The value can be calculated as shown below. 7.5mA is deducted for the no-load
Icc
circuit current of at unused output.
2
VOIO
= 100(%)
VIN(IIN0.0075)
95
STA801M/802M
40.2
a. Part Number
b b. Lot Number
3.150.5
90.2
a 1.20.1
(1)
2(R1)
Pin Arrangement
R-END
.65)
q VO2 Cont y VIN
+0.2
2(R0
0.55 0.1
1.15 +0.2 +0.2
0.550.1 (3.1) w VOS1 u SWOUT2
0.1
4.30.7
9P2.540.5=22.861 e SS1 i SS2
(Tip dimension)
(Tip dimension) r SWOUT1 o VOS22
t GND !0 VOS21
25.250.3
C1.50.5 Plastic Mold Package Type
Flammability: UL94V-0
1 2 3 4 5 6 7 8 9 10 Weight: Approx. 2.5g
Block Diagram
VIN 6 4 SW1
P.Reg.
OCP
SS1 3
PWM
Logic Drive
+
PWM
2 VOS1
+
Amp.
PWM
OSC
Vref
TSD
f/4
Reset
4 SW2
OCP
PWM 10 VOS2 1
SS2 8
Logic Drive
+
PWM 9 VOS2 2
VO2 Cont 1 +
Amp.
GND 5
Vref
96
STA801M/802M
STA800M
VIN 6 4 L1
VIN SWOUT1 VO1
+ C1 5V:100 H See P.98 "Output selection method" for details
220F 9V:150 H
C2 +
3 Ch 1 330F
about connecting VOS2-1 and VOS2-2 of Channel 2.
SS1
+ C4 VOS1
Open:ON 2
Low :OFF 0.47 F
L2
8 7
SS2 SWOUT2 VO2
150 H
C5 +
Open:ON + 0.47 F 10 C3
Low :OFF 1
VO2 Cont Ch 2 VOS2 330F
2
Or
GND
GND VOS2
5 1 9
Ta-PD Characteristics
2
Without Heatsink
0
30 0 25 50 75 100 125
Ambient Temperature Ta (C)
97
STA801M/802M
7 7
VO2 VO2
STA800M 10 11.5V (11.7V)
9V (9.1V) STA800M
9 + 10 +
1 VO2 Cont 1 VO2 Cont
12.1V (12.1V) 15.5V (15.7V)
STA800M STA800M
3 or 8 S.S. 3 or 8 S.S.
+ +
C4, C5 C 4 , C5
98
STA801M/802M
Typical Characteristics
(Ta=25C)
STA801M
Output Voltage(Ch1:5V) Load Regulation(Ch1:5V) Efficiency Characteristics(Ch1:5V)
6 5.1 100
A
0.5A
IO = 0
Output Voltage VO (V)
80
V
4
Efficiency (%)
=7
5.0
20 VIN
0.3A 20V
V
10V
7V 60
V
40V 3 0
2 4.9
40
0 0 0
0 5 10 15 20 0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
20V
0.6
4 8
0A
V
A
=7
IO=
0.5
VIN
40V
0.4
V 0.3A
=40
VIN V 2 4
3 0
0.2 20V
7V
0 0 0
0 0.1 0.2 0.3 0.4 0.5 0 0.2 0.4 0.6 0.8 1.0 0 5 10 15 20
Output Current IO (A) Output Current IO (A) Input Voltage VIN (V)
N=
20V
40 30V
9V
60 0.4 VO ch2
0 V
=4 100 5.0 9.0
VIN VO ch1 5V
30V ch2 9V
40 0.2 V
20
80 ch1 5V 4.8 8.8
V
11
0 0 0 0 0
0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5 40 20 0 20 40 60 80 100 120
Output Current IO (A) Output Current IO (A) Ambient Temperature Ta (C)
STA802M
Load Regulation(Ch1:9V) PD Characteristics(Ch1:9V) PD Characteristics(Ch2:15.7V)
9.1 0.9 0.9
0.8 0.8
30V
Power Dissipation PD (W)
0 0 0
0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5
Output Current IO (A) Output Current IO (A) Output Current IO (A)
99
SDI02
SDI02
2-Output, Low Dropout Voltage Dropper Type for USB
Features
Two 5V/0.5A output regulators in one package
Surface-mount 16 pin package
Low dropout voltage: VDIF 0.5V (at IO = 0.5A)
Output-independent ON/OFF control terminal compatible with LS-TTL (Active
High)
Built in output-independent overcurrent and thermal protection circuits
Open collector flag-output terminals built in to output OCP operation to each
output terminal (Active Low)
Buitl-in anti-malfunction delay circuit whose time can be set with an external
capacitor
Applications
USB power supplies
Electronic equipment
100
SDI02
101
SDI02
External Dimensions
0.890.15 2.540.25
+0.15
a. Part Number
0.75 0.05 0.25
10.3
b. Lot Number
16 9
Pin Arrangement
a
q FLG1 o GND2
6.30.2
0.3
0.5
30.2
9.8
!0 GND2
8
w DLY1
SK b
e VO1 !1 VC2
r VIN1 !2 VC2
Pin1 20 max 8 !3 GND1
0~0.15 t FLG2
+0.15
0.3 0.05 y DLY2 !4 GND1
u VO2 !5 VC1
19.560.2
1.40.2
i VIN2 !6 VC1
3.60.2
4 max
Block Diagram
4 3
VIN1 VO1
VC1 15
VC1
16
1 Reset +
FLG1
+
Latch
OCP
TSD
Set
13
GND1
GND1 2
14 DLY1
8 7
VIN2 VO2
11
VC2
VC2
12
5 Reset +
FLG2
+
Latch
OCP
TSD
Set
9
GND2
GND2 10
6
DLY2
102
SDI02
+
4 VIN 8
*4
VIN CIN*1 D1
15 3
VC1 VC1 VO1 +
VO1
16 Reg. 1 *3 *2
1 2 Cd1 CO1
FLG1 FLG1 DLY1 +
RFLG *4
*5
D2
11 7
VC2 VC2 VO2 +
VO2
RFLG 12 Reg. 2 *3 *2
*5 5 6 Cd2 CO2
FLG2 FLG2 DLY2 +
13 14 9 10
GND
Timing chart
trestart
Is1
IOUT
VOth
VOUT
tDLY
VDLYth
VDLY
tReset
VFLG VFLG
VC VC
FLG output operates after the time tDLY has elapsed (the time set by DLY) after OCP is detected, and is latched. The latch can be
reset by making VC or VIN low. Allow a time lag of Cd x 600 [sec] or more between setting and restarting.
*4 D1, 2 : Reverse biasing protection diode.
This diode is required for protection against reverse biasing of the input and output.
*5 RFLG : Set this to limit the inflow current into the FLG terminal to 1mA or less.
Ta-PD Characteristics
4.0 When mounted on glass-epoxy board
56.5mm 56.5mm (copper foil area 50%)
Total Power Dissipation PD (W)
3.5
With simultaneous operation of two channels
3.0
2.0
1.5
1.0
0.5
0
30 0 25 50 75 100
Ambient Temperature Ta (C)
103
SLA3001M/3002M/3004M
SLA3001M/3002M/3004M
3-Output Dropper/Switching Type
Features
3 regulator ICs combined in 1 package
Insulated single inline package
Can be used with dropper type and switching type
3 independent circuits for input and output respectively. Internal dissipation can
be reduced since different input voltages can be applied.
Dropper type regulator IC is low-dropout voltage type with input/output voltage
difference of 1V. Output ON/OFF control, variable output voltage (rise only) func-
tion
Switching type: built-in separate excitation (60kHz), high efficiency of 80% or
over
Each regulator has overcurrent protection and thermal protection circuit.
Applications
For stabilization of the secondary stage of switching power supplies
Electronic equipment
Lineup
104
SLA3001M/3002M/3004M
VOLINE2 10 30 30 90 90 110
Line Regulation mV
Conditions VIN=6 to 15V, IO=1.0A VIN=17 to 25V, IO=0.5A VIN=14 to 30V, IO=0.3A
VOLOAD2 40 100 120 300 50 80
Load Regulation mV
Conditions VIN=8V, IO=0 to 1.5A VIN=19V, IO=0 to 0.1A VIN=21V, IO=0.1 to 0.4A
f2 60
Switching Frequency kHZ
Conditions VIN=21V, IO=0.3A
Overcurrent Protection IS1, 2 1.6 1.2 0.45
A
Starting Current*1 Conditions VIN=8V VIN=19V VIN=14V
VC Control Voltage (Output ON) VCIH, 2 2.0 2.0 V
Terminal*2 Control Voltage (Output OFF) VCIL, 2 0.8 0.8 V
Recommended DC Input Voltage VIN3 10 20 12 33 12 33 V
VO3 8.64 9.00 9.36 8.55 9.00 9.45 8.64 9.00 9.36
Output Voltage V
Conditions VIN=12V, IO=1.0A VIN=21V, IO=0.3A VIN=21V, IO=0.3A
VDIF3 1.0
Dropout Voltage V
Conditions IO=1.5A
3 85 85
Efficiency %
Conditions VIN=21V, IO=0.3A VIN=21V, IO=0.3A
Regulator 3
External Dimensions
0.2
31
0.2
3.2 0.15 24.40.2 3.20.15 3.8 4.8
16.40.2 1.70.1
a. Part Number
160.2
12.90.2
SK JAPAN
2.450.2
0.2
b. Lot Number
6.10.5
a
9.9
b (Root dimension)
+0.2
9.7 0.5
1.15 0.1 4(R1)
+1
+0.2
0.65 0.1 R-END
Plastic Mold Package
+0.7
(3.6)
0.55 0.1
14P2.030.7=28.421 Flammability: UL94V-0
0.7
(Tip dimension) 4
(Tip dimension) Weight: Approx. 6g
0.2
31.3
1 2 3 4 5 6 7 8 9 10 1112 13 14 15
Block Diagram
4 5 VO1 2 3 L1 VIN
VIN1 VIN1
+ + + +
C1 C1 Protec- D1
Start C4 Start
tion Amp. C4
Amp. 3 4
COMP
2 Protec- 1
VC1 ON/OFF Drive Drive
tion NC OSC Reset
1 5
VREF VREF
4 5 VO1 2 3 L1 VO1 2 3 L1
VIN1 VO1
+ + VIN1 + + + +
C1
Start C4
C1 Protec- D1 VIN3 C1 Protec- D1
Start C4 Start C4
tion Amp. tion Amp.
Amp. 3 COMP 4 COMP 4
2 Protec- 1 1
VC1 ON/OFF
tion
Drive Drive NC Drive
NC OSC Reset OSC Reset
1 5 5
VREF VREF VREF
9 10 VO2 9 10 VO2 7 8 L2
VIN2 VO2
+ +
C2 + + VIN2 C2 + + VIN2 C2 Protec- D2
Start C5 Start C5 Start C5
tion Amp.
Amp. Amp. COMP 9
8 8
7 7 2
VC2 Protec- Drive ON/OFF Protec- Drive NC
ON/OFF VC tion Drive
tion OSC Reset
6 6 10
VREF VREF VREF
14 15 VO3 12 15 L2 VO3 12 13 L3
VIN3 VO3
+ +
C3
+ VIN3 C3 +
Protec- D2 VIN3 C3 +
D2
+
Start C6 Start Start Protec-
tion Amp. C4 tion C6
Amp. Amp.
13 COMP
12 11 COMP
Protec- 14 11
VC3 ON/OFF
tion Drive Drive NC Drive
14
NC OSC Reset OSC Reset
11 15 15
VREF VREF VREF
106
SLA3001M/3002M/3004M
107
SLA3001M/3002M/3004M
Typical Characteristics
(Ta=25C)
SLA3001M (Regulator 2, VO=5V)
Output Voltage Line Regulation Load Regulation
7.0 5.10 5.10
VIN=15V
6.0 5.05 IO=0A 5.05 =8V
IO=1.0A
5.0 0.5A
5.00 5.00
A
4.0
=0
5A
IO
1.
4.95 4.95
3.0
0.5A
1.0A 4.90 4.90
2.0
0 4.80 4.80
0 1.0 2.0 3.0 4.0 5.0 6.0 7.0 0 6 8 10 12 14 16 18 20 0 0.5 1.0 1.5
Input Voltage VIN (V) Input Voltage VIN (V) Output Current IO (A)
Overcurrent Protection Characteristics ON/OFF Control Characteristics Thermal Protection Characteristics
6.0 6 6
VIN=8V VO=5V VIN=8V
IO =1A VO=5V
IO=10mA
5.0 5 5
IO=30V
6V
8V
4.0 4 4
3.0 3 3
OFF
2.0 2 2
ON
1.0 1 1
0 0 0
0 1.0 2.0 3.0 4.0 0 1.0 2.0 3.0 4.0 20 60 100 140 180
Output Current IO (A) Output ON/OFF Control Voltage VC (V) Case Temperature Tc (C)
Note on Thermal Protection:
The thermal protection circuit is intended for protection
against heat during instantaneous short-circuiting. Its op-
eration is not guaranteed for continuous heating condi-
tion such as short-circuiting over extended periods of time.
SLA3002M/SLA3004M(Regulator 1, VO=5V)
Output Voltage Load Regulation Efficiency Characteristics
6.0 5.3 100
5.0 5.2 90
Output Voltage VO (V)
Efficiency (%)
4.0 5.1 80 7V
N=
0A
10V VI
A
IO=
VIN=7V
0.5
3.0 5.0 70
20V
V
0.3A
33V
2.0 4.9 60
1.0 4.8 50
0 4.7 40
0 2 4 6 8 10 0 0.1 0.2 0.3 0.4 0.5 0 0.1 0.2 0.3 0.4 0.5
Input Voltage VIN (V) Output Current IO (A) Output Current IO (A)
Overcurrent Protection Characteristics
6.0
5.0
Output Voltage VO (V)
20V
4.0
7V
3.0
33
2.0
1.0
0
0 0.5 1.0 1.5 2.0
Output Current IO (A)
108
109
SLA3005M/3006M/3007M
SLA3005M/3006M/3007M
4-Output, Low Dropout Voltage Dropper Type for USB Hub
Features
4 regulators combined in one package
Insulated single inline package
SLA 3005M/3006M have four 5V/0.5A outputs. SLA3007M has three 5V/0.5A
outputs and ch4 is a 3.3V/0.5A otuput for USB-IC
Low dropout voltage: VDIF0.5V (at IO=0.5A)
Output-independent ON/OFF control terminal compatible with LS-TTL (Active
High)
Output-independent overcurrent and thermal protection circuits built in
Open collector flag-output terminals built in to output OCP operation to each
output terminal (Active Low) excluding SLA3007Mch4
SLA3005M/3007M (excluding ch4) for VO shutdown after OCP operation and
SLA3006M for continuous OCP operation
Built-in anti-malfunction delay circuit whose time can be set with an external
capacitor
Applications
USB hub power supplies
Electronic equipment
110
SLA3005M/3006M/3007M
*1 IS1 is specified at 5(%) drop point of output voltage VO on the condition that VIN = 7V, IO = 0.1A.
*2 Output is ON even when output control terminal VC is open. Each input level is equivalent to LS-TTL. Therefore, it may be directly driven by an
LS-TTL circuit.
*3 Total of four circuits
* The FLG output latched by delay DLY after OCP detection. (SLA3005M/SLA3007M (ch1 to 3) shuts down the output voltage simultaneously at
latching.) Set the VIN or VC to low to reset latching. Leave a time lag of Cd 600s or more before restart.
** SLA3007Mch4 does not have the FLG output function.
111
SLA3005M/3006M/3007M
a. Part Number
0.2 b. Lot Number
31
0.15 24.4
0.2
3.20.15 3.8 4.80.2
3.2
16.4
0.2 1.70.1 Pin Arrangement
q VC1 !0 FLG3
w FLG1 !1 DLY3
160.2
e DLY1 !2 VO3
130.2
SK JAPAN
2.450.2
9.90.2
6.70.5
b r VO1 !3 GND
t VC2 !4 VC4
9.7 0.5
+0.2
1 0.1
+1
0.65 0.1
+0.2
R-END y FLG2 !5 FLG4 (SLA3007M: NC)
(3)
0.55 0.1
+0.2 u DLY2 !6 DLY4 (SLA3007M: NC)
*
17P1.68 *
0.7=28.56 1
*4 0.7
i VO2 !7 VO4
31.3
0.2 o VC3 !8 VIN
1 3 5 7 9 11 13 15 17
Plastic Mold Package Type
2 4 6 8 10 12 14 16 18 Flammability: UL94V-0
Weight: Approx. 6g
Block Diagram
Reset + Reset + Reset +
FLG1 FLG1 FLG1
(2 pin) (2 pin) (2 pin)
+ + +
Latch
Latch
Latch
OCP
OCP
OCP
TSD
TSD
TSD
+
+
Set Set Set
Reset + Reset + Reset +
FLG2 FLG2 FLG2
(6 pin) (6 pin) (6 pin)
+ + +
Latch
Latch
Latch
OCP
OCP
OCP
TSD
TSD
TSD
+
Set Set Set
Reset + Reset + Reset +
FLG3 FLG3 FLG3
(10 pin) (10 pin) (10 pin)
+ + +
Latch
Latch
Latch
OCP
OCP
OCP
TSD
TSD
TSD
Reset + Reset +
FLG4 FLG4 N.C.
(15 pin) (15 pin) (15 pin)
+ +
Latch
Latch
OCP
OCP
OCP
TSD
TSD
TSD
Set Set
112
SLA3005M/3006M/3007M
SLA3005M/3006M SLA3007M
VIN +
VIN
+ *4
VIN CIN*1 *4
D1
VIN CIN*1 D1
VC1 VC1 VO1 VO1 VC1 VC1 VO1 +
VO1
Reg. 1 + ch1 *3 *2
*3 *2
CO1 FLG1 Cd1 CO1
FLG1 FLG1 DLY1 Cd1 FLG1 DLY1 +
RFLG
+ RFLG *4
*4
D2
*5
D2
*5 VC2 VC2 VO2 VO2
VC2 VC2 VO2 VO2 +
Reg. 2 + ch2 *3 *2
*3 *2
CO2 FLG2 Cd2 CO2
FLG2 FLG2 DLY2 Cd2 FLG2 DLY2 +
+ RFLG
RFLG *4
*D43 *5
D3
*5 VC3 VC3 VO3 VO3
VC3 VC3 VO3 + VO3 +
*5 ch3
*5 Reg. 3
*3 *2 RFLG
*3
Cd3
*2
CO3
RFLG Cd3 CO3 FLG3 FLG3 DLY3
FLG3 FLG3 DLY3 +
+
*4
*4
D4 D4
VC4 VC4 VO4 VO4 VC4 VC4 VO4 +
VO4
+ ch4 *2
*5 Reg. 4
*3 *2 CO4
RFLG Cd4 CO4
FLG4 FLG4 DLY4 +
GND GND
Heatsink: Aluminum
With Silicon Grease: G746
(SHINETSU CHEMICAL INDUSTRIES) t restart t restart
35 Is1 Is1
Infinite Heatsink (TC=25C)
30 Io Io
25 Voth Voth
Vo Vo
20
t DLY t DLY
VDLYth VDLYth
15 VDLY VDLY
10
1001002mm (5.2C/W)
VFLG VFLG
5 75752mm (7.6C/W)
0
Without Heatsink
30 0 25 50 75 100 VC VC
Ambient Temperature Ta (C)
113
SLA3005M/3006M/3007M
IO=0 to 0.5A
3
0.2 200
2
0.1 100
1
0 0 0
0 0.1 0.2 0.3 0.4 0.5 0 1 2 3 4 5 6 0 5 10 15 20
Output Current IO (A) Input Voltage VIN (V) Input Voltage VIN (V)
3
100 Shut-down
20 2
IO=0.25A/CH
50
1
IO=0A/CH
Cd=0V
0 0 0
0 2 4 6 8 10 12 0 2 4 6 8 10 12 0 0.2 0.4 0.6 0.8
Input Voltage VIN (V) Input Voltage VIN (V) Output Current IO (A)
0.75
4.98 4.98
Output Voltage VO (V)
Output Voltage VO (V)
0.70
4.96 IO=0 to 0.5A 4.96 VIN=5.5V
0.1A step 7V
0.65 10V
12V
4.94 4.94 15V
0.60 20V
4.92 4.92
0.55
5 5
0
Output Voltage VO (V)
Output Voltage VO (V)
.5V
4 VIN=5 4
5 7V
10V
3 3
10
20V
2 2
15
1 1
0 20 0
0 0.5 1.0 1.5 2.0 2.5 3.0 0 1 2 3 4 0 20 60 100 140 180
Output ON/OFF Control Voltage VC (V) Output ON/OFF Control Voltage VC (V) Case Temperature (C)
114
SLA3005M/3006M/3007M
0.2
2
1
0.1 1
0 0
0 0 1 2 3 4 5 6 0 1 2 3 4 5 6
0 0.1 0.2 0.3 0.4 0.5
Input Voltage VIN (V) Input Voltage VIN (V)
Output Current IO (A)
Quiescent Circuit Current Circuit Current 1-Circuit (ch1 to 3) Circuit Current (ch4)
500 60 40
ch4 only
Quiescent Circuit Current Iq (off) ( A)
ch1 to 3 only
VC1, 2, 3, 4=0V VC1, 2, 3=0V
400
IO=0.5 to 0A 20
0.1A step
200
20
10
100
0 0 0
0 5 10 15 20 0 2 4 6 8 10 12 0 2 4 6 8 10 12
Input Voltage VIN (V) Input Voltage VIN (V) Input Voltage VIN (V)
Overcurrent Protection Characteristics Overcurrent Protection Characteristics VIN vs. IS1 Characteristics
Overcurrent Protection Starting Current IS1 (A)
6 4 0.80
ch1 to 3 only ch4 only Same for ch1 to 4
5 0.75
VIN=5.5V 12V
3
Output Voltage VO (V)
Output Voltage VO (V)
7V 0.70
4
10V
15V VIN=6V, 7V, 8V, 9V 10V
Shut-down 0.65
3 2
0.60
2
1
0.55
1
Cd=0V
0 0.50
0 5 6 8 10 12 14 16 18 20
0 0.2 0.4 0.6 0.8 0 0.2 0.4 0.6 0.7
Output Current IO (A) Input Voltage VIN (V)
Output Current IO (A)
3.30
4.98 4.98
Output Voltage VO (V)
Output Voltage VO (V)
IO=0 to 0.5A
3.28 0.1A step
4.96 IO=0 to 0.5A VIN=5.5V
4.96
0.1A step 7V
10V 3.26
12V ch4 only
4.94 4.94 15V
18V 3.24
115
SLA3005M/3006M/3007M
VIN=5.5V
3.28 6V 4
7V ch4 5
10V
3.26 3
10
ch4 only
3.24 2
3.20 0 20
0 0.1 0.2 0.3 0.4 0.5 0 0.5 1.0 1.5 2.0 2.5 3.0 0 1 2 3 4
Output Current IO (A) Output ON/OFF Control Voltage VC (V) Output ON/OFF Control Voltage VC (V)
VIN=7V ch1 to 3
5
Output Voltage VO (V)
4
ch4
0
0 20 60 100 140 180
Case Temperature (C)
116
K
Bulletin No
I01 EDO
(Sep,2000)
Sanken Electric Co.,Ltd.
1-11-1 Nishi -Ikebukuro,Toshima-ku, Tokyo
PHONE: 03-3986-6164
FAX: 03-3986-8637
TELEX: 0272-2323(SANKEN J)
North America
Allegro MicroSystems,Inc.
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615, U.S.A.
PHONE: (508)853-5000
FAX: (508)853-7861
Europe
Allegro MicroSystems Europe Limited.
Balfour House, Churchfield Road,
Walton-on-Thames, Surrey KT12 2TD, U.K.
PHONE: 01932-253355
FAX: 01932-246622
IC REG
Dropper Ty
Switching
MultiOutp