Professional Documents
Culture Documents
ESPAOL
CIRCUITOS
Despus de construir los circuitos de este manual, usted podra desear
construir sus propios proyectos. Utilice los proyectos en este libro como
una gua, como una fuente importante de conceptos. Cada circuito
incluir una fuente de energa (las bateras), una resistencia (que puede
ser un resistor, lmpara, motor, circuito integrado, etc.) y conectores
entre las diferentes piezas. Debe ser cuidadoso de no crear cortos
circuitos ya que los componentes se daarn y/o rpidamente
extinguirn la vida de las bateras. nicamente conecte los circuitos
integrados utilizando las configuraciones ofrecidas en este libro, de otra
forma se pueden daar los componentes.
Steren no se hace responsable por daos en piezas debido a un
incorrecto ensamblaje.
ESPAOL-02
Nunca conecte el circuito a un contacto elctrico
Nunca deje un circuito sin atender cuando est encendido
Nunca toque el motor cuando est rotando a alta velocidad
ADVERTENCIA
ESPAOL
Peligro de choque elctrico
Nunca conecte los circuitos a contactos elctricos en
su hogar
ESPAOL-03
Por ejemplo:
Este es un interruptor el cual es verde y viene impreso un nmero en l.
ESPAOL
Este es un conector de circuitos azul y viene en diferentes tamaos y
formas.
ESPAOL-04
Tambin se incluye una placa plstica para ayudar a mantener los
bloques de circuitos unidos. No es necesario utilizar esta placa para
construir proyectos, sin embargo ayuda a que los bloques se
mantengan juntos.
ESPAOL
Algunos circuitos utilizan cables de puenteo para realizar conexiones no
usuales.
ESPAOL-05
LISTA DE PARTES (Colores y estilos pueden variar)
Nmero Descripcin Pieza
2 Cables suaves de conexin
2 Conectores de botn
ESPAOL
6 conectores dobles
4 conectores triples
2 conectores en escuadra
1 conector cudruple
1 conector quntuple
1 conector sextuple
1 Interruptor de vibracin
1 zumbador
ESPAOL-06
Nmero Descripcin Pieza
1 placa sensitiva
1 Interruptor
ESPAOL
1 Interruptor de presin
1 interruptor deslizable
1 fotosensor (CdS)
1 LED
1 lmpara de 2,5V
1 compartimiento de bateras
1 bocina
ESPAOL-07
Nmero Descripcin Pieza
1 circuito musical
1 motor de CD
ESPAOL
1 resistor
1 tubo de transmisin
1 tubo receptor
1 alarma
1 mdulo de control
1 conector
ESPAOL-08
Nmero Descripcin Pieza
1 ventilador amarillo
ESPAOL
1 ventilador de colores
2 soportes de ruedas
2 ruedas
1 imn
1 LED parpadeante
1 LED parpadeante
6 sujetadores plsticos
1 foco
ESPAOL-09
EXPERIMENTOS
ESPAOL
Coloque el interruptor en la posicin de 3V
1.- Lmpara
Cambie a la posicin de encendido (ON) el switch 15, la lmpara 18 se
encender. Apague el switch y la lmpara se apagar.
ESPAOL
Reemplace el ventilador amarillo con el ventilador de color, encienda el
interruptor 15, el ventilador comenzar a girar y parpadear. Apague el
interruptor y el ventilador se apagar.
ESPAOL-12
ESPAOL
Coloque el interruptor en la posicin de 3V
10.- Altavoz
Presione el interruptor 14, y la bocina 20 emitir un sonido.
ESPAOL-13
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-14
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-15
ESPAOL
Coloque el interruptor en la posicin de 3V
13.- LED
Encienda el interruptor 15, el LED 17 se encender. Apague el
interruptor y el LED se apagar.
ESPAOL-16
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-17
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-18
19.- Lmpara y bocina
conectados en serie
Encienda el interruptor 15,
la lmpara encender
sutilmente.
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL
artculo a probar entre el punto A y
el punto B. Si la lmpara se
enciende, el artculo es conductor
(puede ser un cuchillo o un
recipiente de aluminio) Si la
lmpara no enciende, el artculo no
es conductor, como el plstico o la
madera.
ESPAOL-23
30.- Encendido alternado de un motor y un LED controlados
manualmente
Reemplace la lmpara por el motor 24 y reemplace el interruptor 13
por el interruptor de presin 14, controle el circuito con el interruptor de
presin 14, el LED 17 y el motor 24 trabajarn de forma alternada.
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-24
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-25
ESPAOL
Coloque el interruptor en la posicin de 6V
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-27
41.- Compuerta OR de una lmpara
Encienda el interruptor 15 o
presione el interruptor 14, la
lmpara se encender. Esto es lo
que una compuerta OR significa.
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-28
44.- Compuerta OR de conexiones
en serie
Encienda el interruptor 15 o
presione el interruptor 14, la
lmpara se encender y el motor
comenzar a funcionar.
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-29
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-30
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-31
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL
admisin. Coloque el tubo de
transmisin infrarrojo de modo
inverso, el LED no encender,
Coloque el interruptor en la posicin de 3V indicando que el tubo de
transmisin 70 es unidireccional en
conductividad.
ESPAOL-34
60.- Timbre controlado
manualmente
Encienda el interruptor deslizable
15, la bocina comenzar a emitir un
sonido. Cuando la msica se
ESPAOL
detenga, el timbre podr ser
controlado presionando el
interruptor 14.
ESPAOL-35
63.- Timbre controlado por agua
Si el interruptor 14 es reemplazado por un panel tctil 12, la msica
empezar a sonar cuando las gotas de agua toquen el panel tctil.
ESPAOL
detenga, si aplaude o habla fuerte, la msica continuar.
ESPAOL-36
68.- Timbre controlado por
vibracin (1)
Encienda el interruptor 15,
cuando la msica se
detenga, ligeramente toque
la placa instalada en la parte
ESPAOL
inferior 10, la msica
continuar.
ESPAOL-37
71.- Timbre controlado manualmente con retraso de tiempo (2)
Reemplace el LED por el interruptor 14, nicamente presione el
interruptor 14 y la msica continuar.
ESPAOL
interruptor 14 a las terminales A y B, nicamente presione el interruptor
14, la msica continuar.
ESPAOL-38
76.- LED controlado manualmente
Encienda el interruptor 15, cuando
el LED se apague, podr controlar
el LED presionando el interruptor
14.
ESPAOL
77.- LED controlado por imn
Reemplace el interruptor 14 por un
interruptor 13, puede controlar el
LED con un magneto.
ESPAOL-39
81.- LED controlado por sonido con retraso de tiempo (2)
Conecte el zumbador 11 a las terminales B y C, repita el proceso del
proyecto anterior.
ESPAOL
aplauda fuerte hacia la bocina, el LED se encender por un perodo de
tiempo.
ESPAOL-40
86.- LED controlado por vibracin
con retraso de tiempo (1)
Encienda el interruptor 15, cuando
el LED se apague, toque la placa
de vibracin ligeramente, el LED se
encender y se apagar despus
ESPAOL
de un tiempo.
ESPAOL-41
89.- LED controlado manualmente con retraso de tiempo (2)
Reemplace el resistor 30 por el interruptor 14, presione el interruptor
14, el LED se encender por un periodo de tiempo.
ESPAOL
interruptor 14 a las terminales A y B, presione el interruptor 14, el LED
se encender por un periodo de tiempo.
ESPAOL-42
94.- Lmpara parpadeante
controlada manualmente
Encienda el interruptor 15, cuando
la lmpara se apague puede
controlar el parpadeo de la lmpara
presionando el interruptor 14.
ESPAOL
95.- Lmpara parpadeante
controlada por un imn
Reemplace el interruptor 14 por el
interruptor 13, puede controlar el
parpadeo de la lmpara con el
imn.
ESPAOL-43
98.- Lmpara parpadeante controlada por sonido con retraso de tiempo
Conecte el zumbador 11 a las terminales A y B, cuando la lmpara 18
se apague, aplauda y la lmpara se encender de nueva cuenta y se
apagar despus de un perodo de tiempo.
ESPAOL
Conecte el zumbador 11 a las terminales B y C. Repita la operacin del
proyecto anterior.
ESPAOL
encender y se apagar despus
de un momento.
ESPAOL-45
107.- Lmpara parpadeante controlada manualmente con retraso de
tiempo (2)
Reemplace el resistor 30 por el interruptor 14, presione el interruptor
14, la lmpara parpadear de nuevo y se apagar despus de un
momento.
ESPAOL
108.- Lmpara parpadeante controlada manualmente con retraso de
tiempo (3)
Retire el interruptor de vibracin 10, coloque el resistor 30, conecte el
interruptor 14 a las terminales A y B, presione el interruptor 14, la
lmpara parpadear de nuevo y se apagar despus de un momento.
ESPAOL
113.- Motor parlante controlado por
un imn
Reemplace el interruptor 14 por el
interruptor 13, el motor 24 har
sonar la msica utilizando un imn.
ESPAOL-47
116.- Motor parlante controlado por sonido con retraso de tiempo (1)
Conecte el zumbador 11 a las terminales A y B, cuando la msica se
detenga, aplauda fuertemente, el motor 24 har que la msica se
escuche.
ESPAOL
117.- Motor parlante controlado por sonido con retraso de tiempo (2)
Conecte el zumbador 11 a las terminales B y C. Repita la operacin
como en el proyecto anterior.
118.- Motor parlante controlado por sonido con retraso de tiempo (3)
Conecte la bocina 20 a las terminales A y B, cuando la msica se
detenga, aplauda fuertemente, el motor har que la msica se escuche.
119.- Motor parlante controlado por sonido con retraso de tiempo (4)
Conecte la bocina 20 a las terminales B y C. Repita la operacin como
en el proyecto anterior.
ESPAOL-48
120.- Motor parlante controlado por
vibraciones con retraso de
tiempo (1)
Encienda el interruptor 15, cuando
la msica se detenga, golpee
ligeramente la placa de vibracin,
ESPAOL
el motor 24 encender la msica.
ESPAOL-49
123.- Motor parlante controlado manualmente con retraso de tiempo (2)
Reemplace el resistor 30 por el interruptor 14, presione el interruptor
14, el motor 24 encender la msica.
ESPAOL
interruptor 14 a las terminales A y B, presione el interruptor 14, el motor
24 encender la msica.
125.- Motor parlante controlado por imn con retraso de tiempo (1)
Reemplace el interruptor de vibracin 10 por el interruptor 13,
coloque un magneto cerca del interruptor 13, el motor comenzar a
emitir msica.
126.- Motor parlante controlado por imn con retraso de tiempo (2)
Reemplace el resistor 30 por el interruptor 13, coloque un imn cerca
del interruptor 13, el motor 24 comenzar a emitir msica.
127.- Motor parlante controlado por imn con retraso de tiempo (3)
Conecte el interruptor 13 a las terminales A y B, coloque un imn cerca
del interruptor 13, el motor 24 emitir msica.
ESPAOL-50
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL
controlados por sonido.
ESPAOL-52
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-53
ESPAOL
142.- Timbre musical parpadeante controlado manualmente
159 161.- Sonido de msica ajustable controlado por sonido (1) (3)
ESPAOL-57
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-59
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-61
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-63
213.- Apagando el motor y msica
acstica-ptica
Encienda el interruptor 15, cuando
la msica se detenga, presione el
interruptor 14 y sultelo, la bocina
20 reproducir msica
ESPAOL
214.- Apagando el motor y LED con
retraso de tiempo
Reemplace la bocina 20 por un
LED 17 y opere como en el
proyecto anterior.
ESPAOL-64
217.- Apagando el motor y msica parpadeante
Conecte el LED a las terminales C y D y opere como en los proyectos
anteriores.
ESPAOL
junto con el LED 17, opere como en los proyectos anteriores.
ESPAOL-65
221.- Msica de un zumbador
controlada manualmente
Encienda el interruptor 15, cuando
la msica se detenga, podr
controlarla presionando el
interruptor 14.
ESPAOL
222.- Msica de un zumbador
controlado por un imn
Reemplace el interruptor 14 por un
interruptor 13, podr controlar la
msica a travs de un imn.
ESPAOL-66
225.- Msica de un zumbador controlado por sonido (1)
Conecte la bocina 20 a las terminales A y B, cuando la msica se
detenga, aplauda fuertemente, el zumbador 11 emitir sonidos.
ESPAOL
227.- Msica de un zumbador controlada por un motor (1)
Reemplace el motor 24 por una lmpara 18, conecte el motor 24 a las
terminales A y B, cuando la msica se detenga, gire el eje del motor
ligeramente, el zumbador 11 emitir msica.
ESPAOL-67
229.- Msica de un zumbador
controlado por vibraciones con
retraso de tiempo
Encienda el interruptor 15, cuando
la msica se detenga, golpee
ligeramente la placa de vibracin, el
ESPAOL
zumbador 11 emitir msica.
ESPAOL-68
232.- Msica de un zumbador controlado manualmente con retraso de
tiempo (2)
Reemplace el resistor 30 por el interruptor 14, presione el interruptor
14, el zumbador 11 emitir msica.
ESPAOL
tiempo (3)
Remueva el interruptor de vibracin 11, coloque el resistor 30. Conecte
el interruptor 14 a las terminales A y B, presione el interruptor 14, el
zumbador emitir un sonido.
ESPAOL-69
237.- Timbre musical acstico-
ptico controlado manualmente
ESPAOL
239.- Timbre musical acstico-
ptico controlado por luz
ESPAOL-70
245.- Timbre musical acstico-
ptico controlado por vibraciones
(1)
ESPAOL
retraso de tiempo (1)
ESPAOL-71
251.- Timbre musical acstico-ptico controlado por un imn con
retraso de tiempo (2)
ESPAOL
253.- Lmpara parpadeante con
msica
Encienda el interruptor 15, cuando
la msica se detenga, presione el
interruptor 14, la lmpara 18
parpadear y la msica se
escuchar.
ESPAOL-72
256.- Lmpara parpadeante con msica de un zumbador
Reemplace la bocina 20 por un zumbador 11 y conecte en paralelo
al motor 24, presione el interruptor 14, la lmpara 18 parpadear y el
zumbador emitir un sonido.
ESPAOL
Reemplace la lmpara 18 por el motor 24 (haga lo mismo para la
siguiente pieza), reinstale la bocina 20 a su lugar original, presione el
interruptor 14 y sultelo, la bocina 20 emitir un sonido.
ESPAOL-73
261.- Timbre musical controlado por
vibracin con msica rtmica (1)
Conecte el interruptor de vibracin
10 a las terminales A y B, cuando el
sonido se detenga, golpee
ligeramente la placa de vibracin
ESPAOL
y la bocina emitir un sonido de
ritmo lento (Si el efecto no es lo
ideal, puede realizar una conexin
en paralelo hacia un resistor o
capacitor encima del LED).
ESPAOL-74
264.- Timbre musical controlado por sonido con msica rtmica (2)
Conecte el zumbador 11 a las terminales B y C.
ESPAOL
266.- Timbre musical controlado manualmente con msica rtmica (2)
Conecte el interruptor 14 a las terminales B y C.
ESPAOL-75
275.- Sonido de patrulla (1)
Encienda el interruptor 15, la
alarma 72 emitir un sonido de
patrulla.
ESPAOL
Conecte las terminales A y B a
travs de un cable suave, encienda
el interruptor 15, la alarma 72
emitir el sonido de una
ametralladora.
ESPAOL-76
279.- Sonido de una patrulla (2)
Reemplace el interruptor 15 por un interruptor 14, presione el interruptor
14 y la alarma 72 emitir el sonido de una patrulla.
ESPAOL
interruptor 14, la alarma 72 emitir un sonido de una ametralladora.
ESPAOL-77
285.- Sonido de un coche de bomberos
Conecte las terminales E y B a travs de un cable suave, coloque
un imn cerca del interruptor 13, la alarma 72 emitir el sonido de un
coche de bomberos.
ESPAOL
Conecte las terminales E y D a travs de un cable suave, coloque un
imn cerca del interruptor 13, la alarma 72 emitir el sonido de una
ambulancia.
ESPAOL-78
289.- Sonido lento de un coche de bomberos
Conecte las terminales E y B, la alarma 72 emitir el sonido de un
coche de bomberos.
ESPAOL
ambulancia.
ESPAOL-79
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL
ser controlado tocando la placa.
ESPAOL-81
ESPAOL
298.- Ventilador sensitivo (1)
Inserte el conector a la terminal A, mantenga
el tubo infrarrojo fuera de los mdulos de
control del CI 74, salga y entre por el lado
negro y blanco de la tablilla ecuatorial
respectivamente, y podr controlar la
velocidad del ventilador.
ESPAOL
305.- Sonido de ametralladora sensitiva (2)
Conecte las terminales B y E mediante un cable
suave, encienda el interruptor 15, la alarma 72 emitir
el sonido de un coche de bomberos. Mantenga el
tubo infrarrojo fuera de los lados blanco y negro de la
tablilla ecuatorial. El sonido
cambiar a una ametralladora.
ESPAOL
practique en el sistema antirrobo,
puede colocar un cable largo y
delgado a travs del objeto que
desee proteger, como una bicicleta,
autos, puertas, ventanas, etc.
Entonces conecte dos terminales
del cable a las terminales E y B, si
alguien rompe el cable, la alarma
73 emitir el sonido de guerra del
espacio una vez.
ESPAOL
bocina 20 emitir un sonido.
ESPAOL
317.- Alarma de beb
Conecte la placa sensitiva 12 a las terminales C y D, colquelo debajo
de la cama del beb, si la orina del beb cae en la placa sensitiva 12, la
bocina emitir un sonido.
ESPAOL-86
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL-88
ESPAOL
Coloque el interruptor en la posicin de 3V
ESPAOL
ensamblar hasta 10 tipos de alarma diferentes.
ESPAOL-90
ESPAOL
Coloque el interruptor en la posicin de 6V
ESPAOL
Coloque el interruptor en la posicin de 6V
409.- Patrulla trazadora de ruta
Encienda el interruptor, el carro emitir el sonido de una patrulla.
Cuando el carro se est moviendo por la lnea negra, el carro cambiar
el sonido de la patrulla por una ametralladora.
ESPAOL-93
ESPAOL
Coloque el interruptor en la posicin de 6V
ESPAOL-94
ESPAOL
Coloque el interruptor en la posicin de 6V
ESPAOL
3.- Algunas veces las lmparas se aflojan, vuelva a enroscarlas. Tenga
cuidado, ya que el vidrio de la lmpara puede romperse.
4.- Asegrese de que todas las conexiones estn correctamente
conectadas entre ellas.
5.- Intente reemplazar las bateras
ESPECIFICACIONES
Mdulo de energa
Entrada: 6V (4xAA)
ESPAOL-96
LISTA DE PROYECTOS
ESPAOL
ESPAOL-97
ESPAOL
ESPAOL-98
ESPAOL
ESPAOL-99
ESPAOL
ESPAOL-100
ESPAOL
ESPAOL-101
ESPAOL
ESPAOL-102
Producto: Kit educativo avanzado de electrnica
Modelo: K-810
Marca: Steren
PLIZA DE GARANTA
Esta pliza garantiza el producto por el trmino de un ao en todas sus partes y mano
de obra, contra cualquier defecto de fabricacin y funcionamiento, a partir de la fecha de
entrega.
CONDICIONES
1.- Para hacer efectiva la garanta, presente sta pliza y el producto, en donde fue
adquirido o en Electrnica Steren S.A. de C.V.
2.- Electrnica Steren S.A de C.V. se compromete a reparar el producto en caso de estar
defectuoso sin ningn cargo al consumidor. Los gastos de transportacin sern cubiertos
por el proveedor.
3.- El tiempo de reparacin en ningn caso ser mayor a 30 das, contados a partir de la
recepcin del producto en cualquiera de los sitios donde pueda hacerse efectiva la
garanta.
4.- El lugar donde puede adquirir partes, componentes, consumibles y accesorios, as como
hacer vlida esta garanta es en cualquiera de las direcciones mencionadas
posteriormente.
El consumidor podr solicitar que se haga efectiva la garanta ante la propia casa
comercial donde adquiri el producto. Si la presente garanta se extraviara, el consumidor
puede recurrir a su proveedor para que le expida otra pliza de garanta, previa
presentacin de la nota de compra o factura respectiva.
DATOS DEL DISTRIBUIDOR
Nombre del Distirbuidor
Domicilio
Producto
Marca
Modelo
Nmero de serie
Fecha de entrega
ELECTRONICA STEREN S.A. DE C.V.
Camarones 112, Obrero Popular, 02840, Mxico, D.F. RFC: EST850628-K51
STEREN PRODUCTO EMPACADO S.A. DE C.V.
Bilogo MaximIno Martnez No. 3408 Int. 3 y 4, San Salvador Xochimanca, Mxico, D.F. 02870,
RFC: SPE941215H43
ELECTRONICA STEREN DEL CENTRO, S.A. DE C.V.
Rep. del Salvador 20 A y B, Centro, 06000, Mxico. D.F. RFC: ESC9610259N4
ELECTRONICA STEREN DE GUADALAJARA, S.A.
Lpez Cotilla No. 51, Centro, 44100, Guadalajara, Jal. RFC: ESG810511HT6
ELECTRONICA STEREN DE MONTERREY, S.A.
Coln 130 Pte., Centro, 64000, Monterrey, N.L. RFC: ESM830202MF8
ELECTRONICA STEREN DE TIJUANA, S.A. de C.V.
Calle 2a, Jurez 7636, Centro, 22000, Tijuana, B.C.N. RFC: EST980909NU5
ENGLISH-02
ENGLISH
WARNING
SHOCK HAZARD
Never connect snap circuits to the electrical outlets in
your home in any way!
These blocks are indifferent colors and have numbers on them so that
you can easily identify them.
The circuit you will build is shown in color and numbers, identifying the
blocks that you will use and snap together to form a circuit.
For example:
This is the switch block which is green and has the marking on it.
ENGLISH-03
ENGLISH
This is a wire block which is blue and comes in different wire lengths.
To build each circuit, you have a power source block number that need
AA batteries (batteries are not included with the snap circuit kit).
A large clear plastic base grid is included with this kit to help keep the
circuit block together. You do not need this base to build your circuits,
but it does help in keeping your circuit together neatly.
6 two-snap connector
4 three-snap connector
2 3A
1 3B
2 bend wire
1 four-snap connector
1 five-snap connector
1 Six-snap connector
2 #9
1 vibrating switch
1 buzzer
ENGLISH-05
ENGLISH
Number Description Item
1 touch plate
1 press switch
1 slide switch
1 photosensor (CdS)
1 LED
1 2,5V lamp
1 battery compartment
1 speaker
ENGLISH-06
ENGLISH
Number Description Item
1 musical IC
1 DC motor
1 resistor
1 transmission tube
1 receiver tube
1 alarm
1 war space IC
1 control module
1 connector
ENGLISH-07
ENGLISH
Number Description Item
1 yellow fan
1 colour fan
2 gear case
2 wheel
1 magnet
1 flashing LED
1 flashing LED
6 plastic fastener
1 bulb
ENGLISH-08
ENGLISH
PROJECTS
1.- Lamp
Turn on the slide switch 15, the lamp 18 will light up. Turn of the switch
15, and the lamp 18 will switch off.
ENGLISH-10
ENGLISH
6.- Magnet-controlled fan
Replace the slide switch 15 with the switch 13. Place a magnet close to
the switch and the fan will spin round. Take the magnet away from the
switch and the fan will stop.
ENGLISH-11
ENGLISH
Shift the switch to 3V position
10.- Speaker
Press the switch 14 and the speaker 20 will sound.
ENGLISH-12
ENGLISH
Shift the switch to 3V position
ENGLISH-13
ENGLISH
Shift the switch to 3V position
ENGLISH-14
ENGLISH
Shift the switch to 3V position
13.- LED
Turn the switch 15 on, the LED 17 will light up. Turn the switch off and
the LED will put off.
ENGLISH-15
ENGLISH
Shift the switch to 3V position
ENGLISH-16
ENGLISH
Shift the switch to 3V position
ENGLISH-17
ENGLISH
19.- Lamp and speakers
connected in series
Turn the switch 15 on, the
lamp will light up dimly.
ENGLISH-23
ENGLISH
Shift the switch to 3V position
ENGLISH-24
ENGLISH
Shift the switch to 3V position
Question: Why did the yellow fan fly into the air?
ENGLISH-25
ENGLISH
38.- AND gate of a lamp
Turn the switch 15 on, press the
switch 14, the lamp will light up.
This is what an AND gate means.
ENGLISH-29
ENGLISH
Shift the switch to 3V position
ENGLISH-30
ENGLISH
Shift the switch to 3V position
ENGLISH-31
ENGLISH
Shift the switch to 3V position
ENGLISH-33
ENGLISH
60.- Hand-controlled music
doorbell.
Turn the slide switch
15 on, the speaker will
emit a sound. When
the music stops, the music
can be controlled by the
switch 14.
61.- Magnet-controlled
music doorbell
Replace the switch 14 by
the switch 13, you can
control the doorbell with a
magnet.
ENGLISH-35
ENGLISH
68.- Vibration-controlled
music doorbell (1)
Turn the switch 15 on, when
the music stops, touch the
plate 10 installed in the
bottom of the circuit, the
music will resume.
69.- Time-delay
hand-controlled music
doorbell (1)
Replace the vibrating switch
10 with the switch 14, press
once, the music will resume.
70.- Vibration-controlled
music doorbell (2)
Replace the LED with the
vibrating switch 10, touch
the plate softly, and the
music will resume. Shift the switch to 3V position
ENGLISH-36
ENGLISH
71.- Time-delay hand-controlled music doorbell (2)
Replace the LED with the switch 14, press the switch 14 and the music
will continue.
ENGLISH-37
ENGLISH
76.- Hand-controlled LED
Turn the switch 15 on, when the
LED switch off, you can control the
LED pressing the switch 14.
ENGLISH-38
ENGLISH
81.- Time-delay sound-controlled LED (2)
Connect the buzzer to B and C terminals, repeat the operation of the
last project.
ENGLISH-39
ENGLISH
86.- Time-delay vibration-
controlled LED (1)
Turn the switch 15 on,
when the LED switch off,
touch the vibrating plate,
the LED will light up, and
switch off after a short
time.
87.- Time-delay
hand-controlled LED (1)
Replace the vibrating
switch 10 with the switch
14, the LED will light up for
a moment.
88.- Time-delay
hand-controlled LED (2)
Replace the resistor 30
with the vibrating switch
10, touch the plate and the
LED will light up for a short
time.
ENGLISH-40
ENGLISH
89.- Time-delay hand-controlled LED (2)
Replace the resistor 30 with the switch 14, press the switch 14 and the
LED will light up for a moment.
ENGLISH-41
ENGLISH
94.- Hand-controlled
flashing lamp
Turn the switch 15, when
the lamp switch off, you
can control it pressing the
switch 14.
95.- Magnet-controlled
flashing lamp
Replace the switch 14 with
the switch 13, you can
control it using a magnet.
96.- Light-controlled
flashing lamp
Replace the switch 14 with
the photosensor 16, you
can control the flash using
light.
97.- Water-controlled
flashing lamp
Replace the switch 14 with
the vibrating plate 12, the
lamp will flash when you
drop water onto the plate.
Shift the switch to 3V position
ENGLISH-42
ENGLISH
98.- Time-delay sound-controlled flashing lamp (1)
Connect the buzzer 11 to A and B terminals, when the lamp 18 turns off,
clap and the lamp will light up again for a short time.
ENGLISH-43
ENGLISH
104.- Time-delay vibration-
controlled flashing lamp
(1)
Turn the switch 15 on,
when the lamp switch
off, touch the vibrating
plate, the lamp will light up
and turn it off after a
period of time.
ENGLISH-45
ENGLISH
112.- Hand-controlled
singing motor
Turn the switch 15 on,
when the music stops, the
motor 24 will sound after
pressing the switch 14.
113.- Magnet-controlled
singing motor
Replace the switch 14 with
the switch 13, the motor
24 will sound after placing
a magnet close to the
switch.
114.- Light-controlled
singing motor
Replace the switch 14 with
the photosensor 16, the
motor 24 will sound after
controlling it with the light.
115.- Water-controlled
singing motor
Replace the switch 14
with the touch plate 12, if
Shift the switch to 3V position water drips touch the plate
12, the motor will sound.
ENGLISH-46
ENGLISH
116.- Time-delay sound-controlled singing motor (1)
Connect the buzzer 11 to A and B terminals, when the music stops, clap
loudly, the motor 24 will sound.
ENGLISH-47
ENGLISH
120.- Time-delay vibration-
controlled singing motor (1)
Turn the switch 15 on, when
the music stops, know the
plate slightly, the motor 24
will sound.
121.- Time-delay
hand-controlled singing
motor (1)
Replace the vibrating switch
10 with the switch 14, press
the switch 14, the motor 24
will sound.
122.- Time-delay
vibration-controlled singing
motor (2)
Replace the resistor 30 with
the vibrating switch 10, know
the plate slightly, you will
hear music after the motor
24 runs.
ENGLISH-48
ENGLISH
123.- Time-delay hand-controlled singing motor (2)
Replace the resistor 30 with the switch 14, press the switch 14, the
motor 24 will sound.
ENGLISH-49
ENGLISH
Shift the switch to 3V position
ENGLISH-51
ENGLISH
Shift the switch to 3V position
ENGLISH-52
ENGLISH
Shift the switch to 3V position
ENGLISH-54
ENGLISH
Shift the switch to 3V position
ENGLISH-55
ENGLISH
Shift the switch to 3V position
ENGLISH-56
ENGLISH
Shift the switch to 3V position
ENGLISH-57
ENGLISH
Shift the switch to 3V position
ENGLISH-58
ENGLISH
Shift the switch to 3V position
ENGLISH-60
ENGLISH
Shift the switch to 3V position
ENGLISH-62
ENGLISH
213.- Turning the motor off and
acoustic-optic music
Turn the switch 15 on, when the
music stops, press the switch 14,
the music will be listened in the
speaker.
ENGLISH-63
ENGLISH
217.- Turning the motor off and flashing music
Connect the LED to C and D terminals, then operate as last project.
ENGLISH-64
ENGLISH
221.- Hand-controlled sound of a
buzzer
Turn the switch 15 on, when the
music stops, press the switch 14 to
control it.
ENGLISH-65
ENGLISH
225.- Sound-controlled sound of a buzzer (1)
Connect the speaker 20 to A and B terminals, when the music stops,
clap loudly, the buzzer 11 will emit sounds.
ENGLISH-66
ENGLISH
229.- Time-delay
vibration-controlled sound of a
buzzer
Turn the switch 15, when the music
stops, knock the touch plate slightly,
the buzzer 11 will emit music.
231.- Time-delay
vibration-controlled sound of a
buzzer (2)
Replace the resistor 30 with a
vibrating switch 10, knock the touch
plate slightly to emit sounds.
ENGLISH-67
ENGLISH
233.- Time-delay music-controlled sound of a buzzer (3)
Remove the vibrating switch 11, place the resistor 30. Connect the
switch 14 to A and B terminals, press the switch 14,m the buzzer will
emit sounds.
ENGLISH-68
ENGLISH
237.- Hand-controlled acoustic-
optic doorbell
ENGLISH-69
ENGLISH
245.- Vibration-controlled acoustic-
optic doorbell (1)
ENGLISH-70
ENGLISH
253.- Flashing lamp with music
Turn the switch 15 on, when the
music stops, press the switch 14,
the lamp 18 will flash, and the
music will stop.
ENGLISH-71
ENGLISH
257.- Playing music while shutting the motor
Replace the lamp 18 with the motor 24 (do the same for next item),
replace the speaker 20 to the original place, then press the switch 14
once, the speaker 20 will emit a sound.
ENGLISH-72
ENGLISH
261.- Vibration-controlled doorbell
with rhythmic music (1)
Connect the vibrating-switch 10 to
A and B terminals, when the music
stops, knock the touch plate slightly,
and the speaker will emit a
slow-rhythm music (If you cannot
get the desired effect, use a resistor
or capacitor to connect it parallel
over the LED).
ENGLISH-73
ENGLISH
265.- Hand-controlled doorbell with rhythmic music (1)
Connect the switch 14 to A and B terminals, then press the switch 14
and the speaker 20 will emit rhythmic music.
ENGLISH-74
ENGLISH
275.- Police car sound (1)
Turn the switch 15 on, the alarm 72
will emit a police car sound.
ENGLISH-76
ENGLISH
287.- Police car
slow speed sound
Turn the switch
15 on, the alarm
72 will emit a
police car sound,
install a resistor
over the LED to
change the sound
effect.
ENGLISH-78
ENGLISH
295.- Light-controlled space war sound
Replace the switch 15 with a photosensor 16, the sound can be
controlled by light
ENGLISH-79
ENGLISH
298.- Sensitive fan (1)
Insert the connector to terminal A, keep the
infrared tube out of the CI 74 control
modules, come and go by the black and
white side of the barn door, respectively. The
you can control the spped of the fan.
ENGLISH-82
ENGLISH
309.- Nose warning (1)
ENGLISH-84
ENGLISH
Shift the switch to 3V position
ENGLISH-85
ENGLISH
Shift the switch to 3V position
355 361.- Flashing lamp and sound alarm with motor connected in
series
Reconnect the motor 24 with the lamp 18 in series, you can assemble
up to 7 different IC types.
ENGLISH-86
ENGLISH
Shift the switch to 3V position
ENGLISH-88
ENGLISH
Shift the switch to 6V position
Sensitivity and speed of the IC 74 have been adjusted previosuly, if you want to
adjust them turning the knobs to the left or right.
ENGLISH
through a
black line
ENGLISH-90
ENGLISH
Shift the switch to 6V position
ENGLISH-91
ENGLISH
Shift the switch to 6V position
ENGLISH-92
ENGLISH
Shift the switch to 6V position
SPECIFICATIONS
Power module
Input: 6V (4xAA)
ENGLISH-94
ENGLISH
PROJECT LISTINGS
ENGLISH-95
ENGLISH
ENGLISH-96
ENGLISH
ENGLISH-97
ENGLISH
ENGLISH-98
ENGLISH
ENGLISH-99
ENGLISH
ENGLISH-100
Product: Electronic Snap Circuits
Part number: K-810
Brand: Steren
WARRANTY
This Steren product is warranted under normal usage against defects in workmanship and
materials to the original purchaser for one year from the date of purchase.
CONDITIONS
1.- This warranty card with all the required information, invoice or purchase ticket, product
box or package, and product, must be presented when warranty service is required.
2.- If the product stills on the warranty time, the company will repair it free of charge.
3.- The repairing time will not exceed 30 natural days, from the day the claim was received.
4.- Steren sell parts, components, consumables and accesories to costumer, as well as
warranty service, at any of the addresses mentioned later.
a) The consumer can also claim the warranty service in the purchase establishment.
b) If you lose the warranty card, we can reissue it, if you show the invoice or purchase ticket.
RETAILER INFORMATION
Name of the retailer
Address
Product
Brand
Part number
Serial number
Date of delivery
In case your product fails or have questions, please contact your nearest
dealer. If you are in Mexico, please give a call to our Call Center.
Call Center
01 800 500 9000