ANCHOR BOLT DESIGN (Canadian Code CSA A23.3 - 94):
ANCHOR BOLT DESIGN (Canadian Code CSA A23.3 - 94)
Edge distance, ED, = 310 mm ED» = 310 mm
Bolt Spacing, SP, = 130 mm SP = 130 mm
| Bolt dia, d, = 25mm Total Bolt Length,
uy
6
ol Bolt Projection: Projection = 150 min
Emebeded Length La, = Ly ~ Projection - 2d,
5
o—_
Leip = $0.
‘ Fi
ANCHOR BOLT PLAN Hexagonal nut dia. dex = 15dy — dhex = 375mm
Compressive strenth of concrete, ore Boars, ay =F, ay 400.87 mn?
Resistance fators for bolts, 0.67 Tensile strength of anchor bolt, Fg, ay = 414 MPa
Maximum Tension, qj = 200 kN Maximum Shear, Vy = 20kN (Column support reaction)
Tension on each Bolt, Tp = — SOkN Maximum Shear,
Dia of Vertical rebar, yg = 25mm — Total no. 6,
6 Area of 25diabar A,
Total area of Rebar, Achar = bno 2s Acebar = 8000 mm?
Factor for reinforcing bar, 9, = 0.85 Yield strength of rebar, 400 MPa Concrete factor, = 0.60
Edge Distance Check
EDppjn = 100 mm
EDgheck = if(EPpyin > min(ED, ,ED3), "CHECK" \"OK") ED her = "OK"
log 3ANCHOR BOLT DESIGN (Canadian Code CSA A23.3 - 94):
Bolt Steenath Check,
Steel Strenath Refer table 12.1 of Concrete Handbook, pa #12-9
Tensile capaily ofeach bot, 0554.2 Fy am Ty= WOLOLAN
¢
Bot Check, fo
cheat = |oansoe ier 4] 51,
as
(Check = Bok Sate
HECK" otherwise
Ductilty Check,
Concrete Strenath_ (Refer CSA A23,3-94, Append
Effective stress area for tension in each bolt,
ren = (ED + 0.5 SP}) (ED; +0.5SP3) Ajgn = 1406.25 em?
Tensile capacity of each bot, Ty = 0.30, MPa Aten Ty = 138.64KN
2 | maps en
Check Ductilty, Check? = |"DUCTILE* if T, 27,
Reinforcement requ". otherwise [Check = "DUCTILET
Ten = [Ty if Check2 = "Reinforcement requd*
JOKN otherwise ‘Ten =OkN
Development length of rebar depends on diameter of rebar.
‘Area of rebar required for ductile failure, a,
Modified dia of rebar,
co
Refer clause 12.2.3 of CSA-A23.3-94
08
Fornormal density concrete, ky = 10 ky = 10 ky = 1.0 ky gg = 10 hy
RE 3ANCHOR BOLT DESIGN (Canadian Code CSA A23.3 - 94):
Development length of bar, mod if ®mog £20 mm
OAS ky ke ky Ky 20
0454 tay PE ba a> 22
MPa
Development length avaliable, Ly 4yaiy = Lemp ~ (max(ED) D9) ~ SOmm ~ 25mm) Ly gyait= 315mm
Checking of Development of Rebar, Checkd = |*OK" if Ly ya) =by
"CHECK." otherwise [Checks = "OK
Concrete Spalling check for shear force, Refer Figure D3, Appendix D, clause D4.3.6 (c)
Effective stress area for shear along X-X
Ayg = (ED, + 0.5 SP}) (2ED2 + SP) Ay = 281250mm*
Effective stress area for shear along Y-Y,
Ayy = (ED) + 0.5 SP) (26D, + SP)) Ayy= 281250mm?
Effective Stress area for Shear, Ay = min(Ay