Professional Documents
Culture Documents
Description
The 3500/50M Tachometer Module is a 2-channel module that
accepts input from proximity probes or magnetic pickups to
determine shaft rotative speed, rotor acceleration, or rotor
direction. The module compares these measurements against
user-programmable alarm setpoints and generates alarms
when the setpoints are violated.
Page 1 of 10
WARNING
PRODUCT MISUSE
Risk of personal injury or equipment damage.
The analog proportional output is suitable for data logging, chart recording,
or display purposes only. Speed alert setpoints are suitable for
annunciation purposes only.
Magnetic Pickups:
Do not use magnetic pickups for the reverse rotation option or zero speed
option. Otherwise, false indications of rotation direction may occur. The
transducers do not provide a clean edge for the detection circuit during low
speeds.
Page 2 of 10
Transducer
Specifications Power Supply
24 Vdc, 40 mA maximum per channel
+4 to +20 mA
Inputs
Values are proportional to module full-scale
Each 3500/50M Tachometer Module range (rpm or rpm/min).
accepts up to two transducer signals
Signal Recorder Individual recorder values are provided for
from proximity probe transducers or
magnetic pickups. each channel.
Indicates when the 3500/50M Tachometer All other channel types support 0.0039 to
TX/RX LED Module is communicating with other modules 255 events per revolution.
in the 3500 rack.
All channel types support a maximum
Indicates when the 3500/50M Tachometer Speed Input
Bypass LED full scale range of 99,999 rpm and a
Module is in Bypass Mode. maximum input frequency of 20 kHz.
Buffered Transducer
Minimum input frequency for proximity
The front of each module has one coaxial
transducers is 0.0167 Hz (1 rpm for 1
connector for each channel.
event per revolution).
Each connector is short circuit and ESD
Outputs Minimum input frequency for passive
protected.
magnetic pickups is 3.3 Hz.
Buffered outputs are available at the I/O Less than 100 rpm = 0.1 rpm
module via Euro style connectors. 100 to 10,000 rpm = 1 rpm
RPM Accuracy
Output 10,000 to 99,999 rpm = 0.01% of true
550
Impedance shaft speed
Page 3 of 10
Transducer Conditioning Speed 1
Gap 2
Use for any input above 0.0167 Hz Rotor Speed 2
Speed Band
(1 rpm for 1 event/revolution)
Peak Speed 2
Auto Threshold
Minimum signal amplitude for triggering Rotor Acceleration 1
is 1 volt peak-to-peak. Rotor Acceleration Speed
User selectable from +9.5 Vdc to -23.5 Vdc Peak Speed 2
Programmable alarm delays for Alarm 1 1 The primary value for the channel. This value
Alarm Time Delays
and Alarm 2
can be included in contiguous registers in the
From 1 to 60 seconds in 1 second
Alarm 1 Time Delay Communications Gateway Module.
intervals
Speed 1
Rotor Speed Speed Band
Peak Speed 2
Page 4 of 10
Physical Compliance and Certifications
Monitor Module (Main Board) Standards:
Dimensions 241.3 mm x 24.4 mm x 241.8 mm EN 61000-6-2 Immunity for Industrial
(Height x Width x Depth) (9.50 in x 0.96 in x 9.52 in) Environments
Environmental Limits
When used with Internal/External
Termination I/O Module:
-30 C to +65 C
Operating (-22 F to +150 F)
Temperature When used with Internal Barrier I/O
Module (Internal Termination):
0 C to +65 C
(32 F to +150 F)
95%
Humidity
Non-condensing
Page 5 of 10
Hazardous Area Approvals Ordering Considerations
For the detailed listing of country and product
To add the 3500/50M Tachometer Module to an
specific approvals, refer to the Approvals Quick
existing 3500 Monitoring System, you must have
Reference Guide, document 108M1756, at
the following versions of firmware and software:
www.GEmeasurement.com.
Firmware and Software Version
CSA/NRTL/C (Approval Option 01) 3500/22M Module Firmware Revision (1.70)
Ex nC [ia] IIC
3500/01 Configuration Software Version 4.20 or later
Class I, Division 1
3500/02 Data Acquisition Software Version 2.52 or later
AEx nC [ia] IIC
When used with I/O module 3500/03 Display Software Version 1.52 or later
Class I, Zone 2/0
ordering options and internal
Groups A, B, C, D 3500/50M Firmware Revision 5.30 or later
barriers
T4 @ Ta = -20 C to +65 C Not compatible with any
3500/50M
(-4 F to +150 F) version of 3500/20
Page 6 of 10
3500/50M Tachometer Module Cables
3500/50-AXX-BXX
3500 Tachometer Signal to ET Block Cable
A: I/O Module Type
135101-AXXXX-BXX
01 I/O Module with Internal Terminations
02 I/O Module with External Terminations
A: Cable Length
04 I/O Module with Internal Barriers and
0005 5 feet (1.5 metres)
Internal Terminations
0007 7 feet (2.1 metres)
B: Agency Approval Option
0010 10 feet (3 metres)
00 None
0025 25 feet (7.5 metres)
01 CSA/NRTL/C
0050 50 feet (15 metres)
02 ATEX/IECEx/CSA
0100 100 feet (30.5 metres)
External Termination (ET) Blocks
B: Assembly Instructions
Part Number Description
01 Not Assembled
Tachometer ET Block
125808-05 02 Assembled
Euro Style connectors
Tachometer ET Block
128015-05 3500 Recorder Output to ET Block Cable
Terminal Strip connectors
129529-AXXXX-BXX
Recorder ET Block
128702-01
Euro Style connectors A: Cable Length
Recorder ET Block 0005 5 feet (1.5 metres)
128710-01
Terminal Strip connectors 0007 7 feet (2.1 metres)
0010 10 feet (3 metres)
0025 25 feet (7.5 metres)
0050 50 feet (15 metres)
0100 100 feet (30.5 metres)
B: Assembly Instructions
01 Not Assembled
02 Assembled
Page 7 of 10
Spares
Part Number Description
288062-02 3500/50M Tachometer Module
Connector Header
Internal Termination
00580434
8-position|
Green
Connector Header
Internal Termination
00580436
6-position
Green
Connector Header
Internal Termination
00502133
12-position
Blue
Page 8 of 10
Graphs and Figures
1: Status LEDs
2: Buffered transducer outputs
3: I/O Module, Internal Terminations
4: I/O Module, External Terminations
5: I/O Module, TMR, External Terminations
6: I/O Module, Internal Barrier, Internal Terminations
Page 9 of 10
1999 - 2016 Bently Nevada, Inc. All rights reserved.
* Denotes a trademark of Bently Nevada, Inc., a wholly owned subsidiary of General Electric Company.
The information contained in this document is subject to change without prior notice.
Printed in USA. Uncontrolled when transmitted electronically.
1631 Bently Parkway South, Minden, Nevada USA 89423
Phone: 1-775.782.3611 Fax: 1-775.215.2873
www.GEmeasurement.com
Page 10 of 10