Professional Documents
Culture Documents
Nucleus Hardness HRc 60-62. Gold coloured diamond coating finish. Torsion Nucleus Hardness HRc 62-64. Surface-coated with yellow lacquer for rust
zone (extended bar) absorbs torque peaks avoiding premature wear and protection. Torsion zone (extended bar) absorbs torque peaks avoiding
tear, improves and prolongs service life. premature wear and tear, improves and prolongs service life.
Suitable for mass-production line. Suitable for metal and hard materials.
Industrial applications are subject to permanent stresses that place When fastening in metal, the torque increases abruptly at the end of the
high demands on the durability of the tool. fastening process, generating large amounts of peak torque that affects
Bits for these applications are coated with extremely hard titanium both the screw and the tool. Bits that are too hard can be broken under
nitride (TiN). these conditions.
This abrasion-proof coating provides the necessary hardness that is A softer bit is more wear resistant against sudden impacts,
required on a mass production line. preventing the tip from breaking prematurely.
Nucleus Hardness HRc 60-62. Zinc phosphated finish. Torsion zone (exten- Nucleus Hardness HRc 60-62. Steel grey surface-coated with clear lacquer
The profiles ded bar) absorbs torque peaks avoiding premature wear and tear, improves
and prolongs service life.
for rust protection. Torsion zone (extended bar) absorbs torque peaks avoi-
ding premature wear and tear, improves and prolongs service life.
Phillips TORX
Hexagon ball mm Tri-wing T3 1.10 ACR TORSION (64A) 64A
INOX TORSION (65I) 65I
T4 1.30
T5 1.43
Recommended for tasks Ideal for use on stainless
Phillips Grabber TORX Tamper Resistant
Robertson XZN
T6 1.70 requiring reduction of the cam-out effect. steel screws.
T7 1.99
T8 2.31 ACR Torsion bits have a grooved tip (ACR system). Avoids the cam-out effect. Stainless steel does not rust. However, if conventional steel tools are
T9 2.50
Phillips grabber bits for drywall screws (with reduced Torq-set bits are applicable where screws or bolts must T10 2.74 Recommended for tasks requiring reduction of the cam-out effect, used on stainless steel elements or stainless steel screws, the wear
TORX Tamper Resistant nose diameter 4-8mm). be torque-tight. T15 3.27 avoiding erosion of the bit-screw. debris of these tools can adhere to the surface and begin to rust.
TORX Tamper Resistant screws have a centre pin to Tri-wing bits are applicable on tamper resistant screws in T20 3.86 Wear debris causes extraneous rust, but can be prevented by using
prevent a standard TORX driver being inserted. electronic products. T25 4.43
Nucleus Hardness HRc 60-62 . Surface coated with clear lacquer for rust stainless steel tools. Inox in combination with Torsion gives a superior
HEX BALL
T27 4.99
Hexagon ball point bits facilitate working in confined XZN bits are suitable for automotive high torque applications. T30 5.52 protection. Grooved tip (ACR system) avoids the cam-out effect. Torsion bit that can withstand even highest demands.
spaces by using at an angle. zone (extended bar) absorbs torque peaks avoiding premature wear and
Bits tip coated with thousands of tiny industrial-grade T40 6.65
Robertson bits tapered tip retains the screw for easier opera- diamond particles. T45 7.82 tear, improves and prolongs service life. Nucleus Hardness HRc 60-62. Surface passivated finish. Surface coated
tion and give more surface contact, reducing cam-out effect. T50 8.83
with yellow lacquer for rust protection. Torsion zone (extended bar) absorbs
torque peaks avoiding premature wear and tear, improves and prolongs
service life.
torsion
59S
STANDARD (59S)
Bit assortment
Bit assortment
Nucleus Hardness HRc 58-62. Precisely machined tip. Zinc phosphated finish.
2 3
The Range torsion STANDARD Bit set assortment
63D: 62TIN: 60T 61H: 64A: 65I: 59S:
The Choice: Diamond TIN Torsion Extra Hard ACR INOX Torsion Standard
Torsion Torsion Torsion Torsion Stainless Steel
BIT SETS 31 pcs
Bahco exclusive designed case
Each set contains 31 pcs that meet most requirements in terms of
quality, range and application
1/4 (DIN3126-C6.3, ISO1173 / E6.3, ISO1173) OTHER DRIVES Covering the following applications: Phillips, Pozidriv, Torx, Slotted, Hex,
Phillips Grabber, Torx TR: in standard and Torsion execution
Bit set with handy soft rubber belt clip
range Content
59S/31-1 0191451 31 pcs standard 1 pc PH1,3xPH2,PH3,2XPH2G,PZ1,3XPZ2,PZ3,T10,3XT15,3XT20,2XT25,T27,T30,
0.5X3.0,0.6X4.5, 0.8X5.5mm, 3.0,4.0,5.0,6.0mm,KM653-QR -60mm
59S/31-2 0191468 31 pcs standard 1 pc 4XPH2,4XPH2G,4XPZ2,2XT10,4XT15,5XT20,5XT25,2XT30,KM653-QR -60mm
59S/31-3 0191475 31 pcs standard 1 pc 2XPH1,2XPH2,PH3,2XPZ1,3XPZ2,PZ3,2XTR10,3XTR15,5XTR20,4XTR25,
TR27,4XTR30,TR40,KM653-QR -60mm
60T-31-1 0191482 31 pcs Torsion 1 pc PH1,3XPH2,PH3,2XPH2G,PZ1,3XPZ2,PZ3,T10,3XT15,3XT20,2XT25,T27,2XT30,
0.6X4.5, 0,8X5.5mm, 3.0,4.0,5,0,6.0,1/4-60mm
range Content
59S/17-1 0191499 17 pcs standard 1 pc PH1,3xPH2,2xPH2G,PZ1,2xPZ2,
3.0,4.0,5.0,6.0,, 3.0,4.5,5.5mm,1/4-50mm
59S/17-2 0191505 17 pcs standard 1 pc T7,T8,T9,T10,2xT15,3xT20,3xT25,T27,
2xT30,T40,1/4-50mm
59S/17-3 0191512 17 pcs standard 1 pc PH1,2xPH2,PZ1,PZ2,PZ3,T10,T15,T20,T25,T
27,T30,T40, 3.0,4.0,5.0mm,1/4-50mm
Bit assortment
Bit assortment
4 5
BIT SETS 7 pcs Power nut drivers / adaptors / holders
Bahco exclusive designed case with easy push open / pull close function, carded
8 bit sets: Standard, Torsion, Inox, TIN & Diamond, zinc phosphated, all of high
performance alloy steel Power nut drivers UNIVERSAL HOLDERS
Drive: DIN 3126-E 6.3, ISO 1173 Drive: DIN 3126-E 6.3, ISO 1173
Each set contains 6 bits DIN 3126-C6.3, ISO 1173, 25mm(L) and one universal bit
Black finish High performance alloy steel
holder*) DIN 3126-C6.3, ISO 1173, 50mm(L) High performance alloy steel
Covering following applications: Phillips, Pozidriv, Torx, Torx TR Hexagon socket
* Magnetic universal holder: Standard,TIN Torsion,Torsion set Magnetic universal holder+retaining ring: KR653 0204885 1/4 1/4 60 Black finish; with retaining
K6750-6 0204670 6 mm 1/4 11.5 50 ring; DIN 3126 D 6.3
Diamond set Stainless steel universal holder+ ret. ring: stainless steel set.
K6750-7 0204687 7 mm 1/4 12 50
PH2,PZ2,T15,T20,T25,T30 + holder PH2,PZ2,T15,T20,T25,T30 + holder K6750-8 0204694 8 mm 1/4 12.5 50
K6750-10 0204700 10 mm 1/4 14.5 50
K6750-13 0204823 13 mm 1/4 17 50 Stainless steel;
KSR753 0204892 1/4 1/4 75
K6750-1/4 0204663 1/4 1/4 10.5 50 with retaining ring;
KSR753-1P 0204908 1/4 1/4 75
K6750-3/8 0204656 3/8 1/4 14.4 50 DIN 3126 D 6.3
range Content
KM653-SF 0204984 1/4 1/4 14 60 KM653-QR 0115983 1/4 1/4 14 60
59S/22-1 0204229 22 pcs standard 1 pc PH1, 2, 3;PH2G;PZ1,2,3;T6,8,9,10,15,20,25,27,30,40;
KM653-QR -1P 1848507 1/4 1/4 14 60
3.0,4.5,5.5mm;1/4-50mm;K6650 1/4-50mm
59S/22-2 0204236 22 pcs standard 1 pc 3xPH2;3xPH2G;2xPZ2;T10,4xT15,3xT20,2xT25;
2.5,3.0mm;1/4-50mm;K6650 1/4-50mm KM100-SH, QUICK RELEASE BIT
Bit assortment
Bit assortment
6 7
Accessories
Bahco also offers a full range of ratchet and bit screwdrivers. Exclusive features such as the 48 teeth ratchet function, the super grip 2-component handle,
the cartridge bit storage and the led light function make your work easier and more efficient. All products have the same distinctive Bahco look, a design that
stands out from the crowd.
B&C-0956-ENG
26 pce bit and sockets set for slotted, STUBBY RATCHETING SCREWDRIVER SET
Phillips, Pozidriv, Hexagon and TORX Stubby ratcheting 1/4 bit holder, bits and sockets set
head screws
Lightweight, rounded corners handy injection case
Detachable square driver blade
808050S-18
26 pce set: 18 bits + 5 sockets + 1 bit
1 pce detachable square driver blade stubby ratcheting
rachet + 1 adaptor + 1 bit holder
screwdriver
In a plastic box / SB=on card
8 pcs S2 Zinc Phosphate bits: PH 1, PH 2, PZ 1, PZ 2, T-15,
Drive: 1/4 DIN 3126-C 6, ISO 1173
T-20, SL 4, HEX 3
Finish: Bits: zinc phosphate, sockets:
1 pce x1/4 socket adaptor
chrome, ratchet; plated
1pce Sq. x1/4 hex bit holder 50 mm (changeable type)
Material: High performance alloy steel
1pce Sq.x square flexible socket adaptor 150 mm
1pce x bit adaptor
5 pcs sockets: 4, 5, 6, 7, 8 mm
808050S-22
1 pce detachable square driver blade stubby ratcheting
screwdriver
17pcs S2 Zinc Phosphate bits: PH 1, PH 2, PH 3, PZ 1, PZ 2,
T-10, T-15, T-20, T-25, T-27, T-30, T-40, SL 4, SL 5, SL 5.5,
2058/S26 1849276 1 35x100x80 300 SL 6.5, SL
SB-2058/S26 1849498 1 55x120x190 325 1pce x1/4 socket adaptor
1pce Sq. x1/4 hex bit holder 50 mm (changeable type)
PH PZ 1pce Sq.x square flexible socket adaptor 150 mm
1, 2, 3 1, 2, 3 1pce x bit adaptor
TORX HEX
T10, T15, T20, T25, T30 3, 4, 5, 6
808050S-18 0128921 195x130x46
808050S-22 0128938 195x130x46
SL 5 pieces
4, 5, 6 mm 6, 7, 8, 10, 13 mm
2058-BR
1/4 - 8 mm
1 pce
1/4 - 1/4
BIT HOLDER
Developed according to the scientific ERGO process
Bit holder for 1/4 bits
Handle: 3-component handle, for maximum user comfort and force transmission
2058/S26-2 1849283 1 35x100x80 300 Easy to choose the right tip, with the colour-coded handle
Blade: High performance alloy steel. Chrome plated and entirely hardened
PH PZ
0, 1, 2 0, 1, 2
TORXT HEX
4, T5, T6, T7, T8 1.5, 2, 2.5, 3
SL 2058-BR
3, 4, 5 mm 1/4 - 8 mm
1 pce K6625-1/4
1/4 - 1/4 1/4 BE-8577 1839048 1/4 118 36x122 240
5 pieces
4, 5, 6, 7, 8 mm