Professional Documents
Culture Documents
Vishay Sprague
Polypropylene Film Capacitors
High Performance, ORANGE DROP
Type 716P ORANGE DROP is a high performance version of the popular Type
715P. It is made from polypropylene and foil with copper leads for the ultimate
in high pulse current and high rms current capability. It is a pressed unit for better
utilization of board space.
The 200 V, 400 V and 600 V ratings are single section, extended foil units
allowing for high frequency, high current applications. The 800 V, 1200 V and
1600 V ratings are series-wound extended foil with a floating metalized common
foil which provides self-healing characteristics in addition to high frequency,
high current capabilities.
Capacitance change with temperature is less than 3% over the entire operating
temperature range. The temperature coefficient is negative and virtually linear
at 180PPM/C over the temperature range of + 25C to
+ 105C. This characteristic means the Type 716P is suitable for matching with
positive TC resistors and inductors to maintain circuit stability.
Type 716P ORANGE DROP capacitors are conformally coated with a flame
retardant epoxy.
PERFORMANCE CHARACTERISTICS Humidity Test: Condition capacitors with no voltage
Operating Temperature: - 55C to + 85C, standard; applied for 72 hours @ 95% relative humidity and + 75C.
+ 105C provided working voltage is reduced to 50% of Remove capacitors from humidity chamber, wipe surface
+ 85C rating. dry of moisture and dry in circulating air for 4 hours.
Insulation Resistance: After a 2 minute charge at rated Measure insulation resistance after a 2 minute charge
voltage or 500 V, whichever is less. @ + 25C and rated voltage or 500 VDC, whichever is less.
At + 25C: 400,000 Megohm for C .5 Microfarads. Minimum product of insulation resistance and capacitance
200,000 Megohm - Microfarads for C > .5 Microfarads. shall be 50,000 Megohm - Microfarads after test but need
At + 85C: 20,000 Megohm for C .5 Microfarads. not exceed 100,000 Megohm. Not more than one failure
10,000 Megohm - Microfarads for C > .5 Microfarads. in 12 units tested shall be permitted.
At + 105C: 2000 Megohm for C .5 Microfarads. DC Life Test: Capacitors are capable of withstanding a
1000 Megohm - Microfarads for C > .5 Microfarads. 500 hour life test @ + 85C @ 150% of rated working
Capacitance, Tolerance and Dissipation Factor: voltage. After test, capacitance shall not have changed by
Capacitors shall be measured at a frequency of 1000Hz more than 5% of initial value, insulation resistance shall not
@ + 25C or else be referred to measurements made at have decreased by more than 50% of the initial limit and
that frequency and temperature. The maximum dissipation dissipation factor shall not have increased to more than 0.1%.
factor is 0.1%. AC Life Test: Capacitors shall withstand the maximum
Dielectric Withstanding Voltage: Capacitors rated below 60Hz voltage for a period of 500 hours @ + 85C.
1000 volts shall withstand a DC potential of 250% of rated
voltage applied between terminals for not more than Rated DC Voltage Maximum 60Hz Voltage
5 seconds. 200 155
Capacitors rated 1000 volts and above shall withstand a
400, 600 200
DC potential of 200% of rated voltage applied between the
terminals for not more than 5 seconds. The test voltage 800, 1200, 1600 500
must be applied and discharged through a resistor of 1 ohm
per volt. Not more than one failure allowed in 12 units tested.
H
Max.
0.250
0.250
[6.350] 0.250
[6.350]
Max. [6.350]
1.250 Max.
Max.
[31.750] Lead Lead
Min. Length Length
Tinned Copper
S S S
0.060 [1.524] 0.030 [0.762] 0.030 [0.762]
PERFORMANCE CHARACTERISTICS
PERCENT CAPACITANCE
+2 102
CHANGE - 1000Hz
+1 5
0
2
-1 TYPICAL
TAN
103
-2
- 55 - 50 - 25 0 + 25 + 50 + 75 + 85 + 100 + 105 + 125
5
TEMPERATURE DEG. CENTIGRADE
PERCENT DISSIPATION
2
FACTOR - 1000Hz
0.075 TYPICAL
104
0.05 TYPICAL
1000 1000
5 5
2 200
VOLTS - rms
VOLTS - rms
.0
03
155 .0 9
.0 15 F
100 1 100 F
.1
.5 .1 F
F
6 F
F
.4
7
5 5 .0
F
.0 47
47 .2 F
200 V F
.1
400 V
7
1.
F
0
2 2
F
10 10
1 2 5 10 2 5 100 2 5 1000 1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz FREQUENCY - kHz
1000 1000
5 450
.0
01
F .0
200 .0 05
2 47
VOLTS - rms
VOLTS - rms
.0 F 6
.0 05 F
47 6
100 F F
100
.0
.2
.0 82
2
15
F F
F
5 .1 .0
2 5 15
F F
600 V 800 V
2 2
.1
4
F
10 10
1 2 5 10 2 5 100 2 5 1000 1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz FREQUENCY - kHz
PERFORMANCE CHARACTERISTICS
1000 1000
475 500 .0
.0 01
.0 02 .0 F
15 7 08
F F 2
200 2 F
VOLTS - rms
.0
VOLTS - rms
03
.0 .0 3
06 15 F
100 8 100 F
F
.0
56
F
5 5 .0
.0
33
33
F
F
1200 V
2 2 1600 V
10 10
1 2 5 10 2 5 100 2 5 1000 1 2 5 10 2 5 100 2 5 1000
FREQUENCY - kHz FREQUENCY - kHz
ORDERING INFORMATION
716P 104 9 1 J D 3
TYPE CAPACITANCE TOLERANCE DC VOLTAGE CASE CODE TERMINAL LEAD LENGTH
RATING
This is expressed in 0 = 20% This is expressed See Dimensions. A = Straight lead 1 = 0.187" 0.030"
picofarads. The first two 9 = 10% in hundreds of volts. B = Hairpin crimped [4.750 0.762]
digits are significant. The 5 = 5% D = Hockey crimped 2 = 0.250" 0.030"
third is the number of zeros [6.350 0.762]
to follow. Values must 3 = 1.250" [31.750]
conform to decade rating Minimum
for the tolerance specified.
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, Vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishays terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.