You are on page 1of 3

Semi Built Crankshaft Photographs http://www.marinediesels.co.uk/2_stroke_engine_parts/Other_info/dual_...

Operational Information
The 2 Stroke Dual Fuel Engine

Other Pages The Basics The 2 Stroke Engine The 4 Stroke Engine Operation Members

INTRODUCTION

With the two stroke engine the gas cannot be mixed with the inlet air as it would turn the scavenge space into an
enormous bomb!
There are two possible methods of introducing the gas into the cylinder:
The first method introduces low pressure gas through a gas admission valve in the cylinder head when the exhaust valve
has closed and pressure in the cylinder is low. The gas is compressed and mixed with the air and ignited by pilot injection
of fuel oil.

1. The exhaust valve is closed and the gas 3. At just before TDC a pilot injector injects a
2. The gas admission valve is closed and the
admission valve is open. Gas at a higher small amount of fuel oil into the cylinder
piston moves up the cylinder compressing
pressure than cylinder pressure flows into the which starts to burn and ignites the gas/air
the gas/air mixture.
cylinder mixture.

4. The piston is forced down the cylinder by 5. The exhaust valve opens followed by the
the burning expanding gas. scavenge ports. Air enters the cylinder
pushing out the exhaust gas.

The disadvantage of this system although simple, is that combustion is subject to knock and the efficiency is low

The second method is to compress the gas to a high pressure (250 - 300 bar) and inject it into the cylinder through special

1 of 3 07-02-2017 00:18
Semi Built Crankshaft Photographs http://www.marinediesels.co.uk/2_stroke_engine_parts/Other_info/dual_...

gas injectors at the same time as the fuel oil. This is the method which has been developed by MAN B&W in their ME GI
engine which is basically the electronic camshaftless engine fitted with the extra equipment to inject the gas into the
engine. The engine is fitted with gas injection valves in addition to the fuel valves and because it is computer controlled
can burn any ratio of gas and fuel with a preset minimum amount of fuel.

INJECTION CONTROL

The injection control system is modified from the standard electronic engine as shown.

The gas is pressurised by reciprocating compressors to 250 - 300 bar. It is then cooled and led to the valve blocks on each
cylinder. Each valve block incorporates an accumulator which has a volume corresponding to about 20 times the amount
of gas injected at full load operation. The purpose of the accumulator is to minimise any pressure drop during gas
injection, and to monitor that small pressure drop as it forms an important part of the engines safety system.

The engine can run in various modes depending on circumstances.

1. Normal dual fuel whereby the pilot fuel injected is about 6% of the load. If the gas supply is limited, then extra fuel
oil will be injected to maintain power.
2. If a limited, but constant gas supply is available, the engine can be run in what is known as specified gas mode.
When in this mode, the same amount of gas is injected each time, with the amount of fuel oil varying, depending on
engine load.
3. Fuel only mode, for manoeuvring or when no gas is available.

The gas supply pipes are double walled with an air seal being supplied between the two pipes. Pressurised air, supplied by
fans is then monitored for gas leakage. Because a failure of the inner gas pipe, could lead to very low temperatures as the
high pressure gas expands as it leaks out, the outer pipes are made of a stainless steel able to withstand these low
temperatures. The flow of air through the air seal is also monitored. Lack of flow would lead to shut down of the gas
supply and purging of the lines with inert gas.

To prevent leakage of gas at the injectors and to lubricate the moving parts, the gas injectors are supplied with sealing oil
which is pressurised to 25 - 50 bar above the gas injection pressure. The small amount of oil which leaks through to the
gas is then burnt in the engine. Consumption is low (about 0.13g/kWh). The sealing oil system comprises of two pumps

2 of 3 07-02-2017 00:18
Semi Built Crankshaft Photographs http://www.marinediesels.co.uk/2_stroke_engine_parts/Other_info/dual_...

for redundancy purposes and a spring loaded accumulator to maintain the pressure if a pump fails, whilst the standby
pump comes up to pressure.

Should a gas injector jam open then a pressure drop will occur in the accumulator in the valve block and the system will
shut down, and the gas lines will be purged with inert gas. Should the pressure drop not be detected, the excess gas
entering the cylinder will continue to burn as it leaves leading to a high exhaust temperature on that cylinder, leading to
slow down, again shutting off the gas supply. In the unlikely event of late ignition of the gas occurring in the exhaust
manifold, leading to a rapid pressure rise, the receiver is designed to withstand a pressure of 15 bar.

Any failure of injection of pilot fuel leading to non combustion of the injected gas will lead to the gas supply being shut
off and the gas lines purged with inert gas.

IACS require that the following safety requirements must be met:

Only oil fuel is to be used when starting the engine.


Only oil fuel is, in principle, to be used when the operation of an engine is unstable, and/or during manoeuvring and
port operations.
In case of shut-off of the gas fuel supply, the engines are to be capable of continuous operation by oil fuel only.
Crankcase relief valves are to be fitted in way of each crankthrow. The construction and operating pressure of the
relief valves are to be determined considering explosions due to gas leaks.
Explosion relief valves or other appropriate protection system against explosion are to be provided in the exhaust,
scavenge and air inlet manifolds.
The exhaust gas pipes from Dual Fuel engines are not to be connected to the exhaust pipes of other engines or
systems.
Starting air branch pipes to each cylinder are to be provided with effective flame arresters.
Flame arresters are to be provided at the inlet to the gas supply manifold for the engine.
Arrangements are to be made so that the gas supply to the engine can be shut-off manually from the starting
platform or any other control position.

If a cross-head type engine is used as a Dual Fuel engine:

The crankcase is to be protected by oil mist detector or bearing temperature detector.


Gas detecting or equivalent equipment is to be provided for piston underside space of cross-head type engine.

The engine must be designed to stop before the gas concentration detected by the gas detectors specified reaches 60% of
lower flammable limit.

See Also: The 4 Stroke Dual Fuel Engine

DHTML Menu / JavaScript Menu Powered By OpenCube

3 of 3 07-02-2017 00:18

You might also like