Professional Documents
Culture Documents
it
de
fr
Instructions for Use
it
IMPORTANT SAFEGUARDS
These safeguards apply for machines with UL safety test (see rating
plate and chapter 9, Technical data).
Follow the basic safety When using electrical appliances, basic safety precautions should
precautions always be followed, to reduce the risk of fire, electric shock, and/or
injury to persons, including the following:
Z Read all instructions.
Z Do not touch hot surfaces. Use handles or knobs.
Z To protect against fire, electric shock and injury to persons, do not
immerse cord, plugs, or body of machine in water or other liquid.
Z Close supervision is necessary when any appliance is used by or
near children.
Z Unplug from outlet when not in use and before cleaning. Allow to
cool before putting or taking off parts, and before cleaning the
appliance.
Z Do not operate any appliance with a damaged cord or plug or
after the appliance malfunctions, or has been damaged in any
manner. Return appliance to the nearest authorized service facility
for examination, repair or adjustment.
Z The use of accessory attachement not recommended by the
appliance manufacturer may result in fire, electric shock, or injury
to persons.
Z Do not use outdoors.
Z Do not let the cord hang over the edge of a table or counter, or
touch hot surfaces.
Z Do not place on or near a hot gas or electric burner, or in a heated
oven.
Z Always attach plug to appliance first, then plug cord into the wall
outlet. To disconnect, turn any control to OFF then remove plug
from wall outlet.
Z Do not use appliance for other than intented use.
Z Use extreme caution when dispensing hot steam.
Z For household use only.
Special cord set instructions a. A short power supply cord is provided to reduce the risk resulting
from becoming entangled in or tripping over a long cord.
Your ENA has a 3-pin grounded plug.
b. Longer extension cords are available and may be used if care is
exercised in their use.
Z As a safety feature, this plug will fit in a polarized outlet only one
way.
Z If the plug does not fit fully in the outlet, reverse the plug. If it still
does not fit, contact a qualified electrician.
Z Do not modify the plug in any way or attempt to defeat this
safety feature.
en
Warning To reduce the risk of fire or electric shock, do not remove any service
covers. No user serviceable parts inside. Repair should be done by
authorized personnel only.
Caution This appliance is for household use. Any servicing other than cleaning
and user maintenance should be performed by an authorized service it
representative:
Z Do not immerse base in water or try to disassemble.
Z To reduce the risk of fire or electric shock, do not remove the base.
No user serviceable parts inside. Repair should be done by
authorized service personnel only.
Z Check voltage to be sure that the voltage indicated on the name de
plate agreees with your voltage.
Z Never use warm or hot water to fill the water container! Use cold
water only.
Z Keep your hands and the cord away from hot parts of the
appliance during operation.
Z Never clean with scouring powders or hard implements. fr
NEVER DO Z Never fill instant coffee, chocolate mix etc. into the grinder or
(or you will void your ground coffee funnel (grunder by-pass). It will damage the
warranty protection): functioning of the brewing chamber.
Z Never fill sugar coated coffee beans into the bean hopper. In case
of doubt, call your dealer. it
Z Never fill anything other than coffee beans into the bean container
(no chocolate, no rice, no nuts, no spices, nothing other than
roasted coffee beans).
Z Never do anything with the machine which is not described in the
Users Manual. In case of doubt, call your dealer.
3
ENA 5
Z Keep your hands and the cord away from hot parts of the
appliance during operation.
Z Never clean with scouring powders or hard implements.
NEVER DO Z Never fill instant coffee, chocolate mix etc. into the grinder or
(or you will void your ground coffee funnel (grunder by-pass). It will damage the
warranty protection): functioning of the brewing chamber.
Z Never fill sugar coated coffee beans into the bean hopper. In case
of doubt, call your dealer.
Z Never fill anything other than coffee beans into the bean container
(no chocolate, no rice, no nuts, no spices, nothing other than
roasted coffee beans).
Z Never do anything with the machine which is not described in the
Users Manual. In case of doubt, call your dealer.
4
ENA 5
en
it
de
fr
it
5
ENA 5
Your ENA 5
IMPORTANT SAFEGUARDS 2
Control elements 8
Proper use 10
For your safety 10
Welcome to the world of JURA 11
JURA on the Internet .............................................................................................................................................11
Knowledge Builder ................................................................................................................................................11
Connector System ..............................................................................................................................................11
3-colour plain text display ...................................................................................................................................12
1 Preparing and using for the first time 12
Supplied as standard............................................................................................................................................12
Setting up...............................................................................................................................................................12
Filling the water tank ...........................................................................................................................................12
Filling the bean container ................................................................................................................................... 13
First-time use ......................................................................................................................................................... 13
Using and activating filter ...................................................................................................................................14
Determining and adjusting the water hardness .............................................................................................14
Adjusting grinder ..................................................................................................................................................15
Switching on the machine ..................................................................................................................................15
Switching off the machine ..................................................................................................................................16
2 Preparation 16
Barista tips .............................................................................................................................................................16
1 coffee at the touch of a button ....................................................................................................................... 17
2 coffees at the touch of a button ..................................................................................................................... 17
Pre-ground coffee ................................................................................................................................................. 17
One-off setting before and during preparation ..............................................................................................18
Entering a default setting for the amount of water for a cup size...............................................................18
Cappuccino with the Professional Cappuccino Frother .................................................................................19
Cappuccino with the Easy Cappuccino Frother ..............................................................................................19
Cappuccino with the 2-stage frothing nozzle ................................................................................................20
Heating milk with the Professional Cappuccino Frother ..............................................................................20
Heating milk with the 2-stage frothing nozzle ...............................................................................................21
Hot water ..............................................................................................................................................................21
3 Default settings in programming mode 22
Products ................................................................................................................................................................ 22
Energy-saving mode ........................................................................................................................................... 22
Automatic switch-off........................................................................................................................................... 23
Units of water ....................................................................................................................................................... 23
Language............................................................................................................................................................... 23
4 Maintenance 24
Maintenance tips .................................................................................................................................................24
Rinsing the machine manually ......................................................................................................................24
Changing the filter following a prompt ........................................................................................................... 25
Changing the filter manually ......................................................................................................................... 25
Cleaning the machine following a prompt ..................................................................................................... 25
Cleaning the machine manually....................................................................................................................26
6
ENA 5
it
de
Symbol description
Warnings:
J CAUTION fr
Always take note of any information Symbols used:
marked with the CAUTION or WARNING
symbol. The signal word WARNING E Information and tips to make use of
points out potential risk of serious your ENA even easier.
injury, and the signal word CAUTION
potential risk of slight injury. T Prompt to take action. This symbol
means that you are being prompted to
perform an action. it
CAUTION
The CAUTION symbol is used to draw @ References to the JURA website where
attention to circumstances which could you can find interesting additional infor-
result in damage to the machine. mation: www.jura.com.
7
ENA 5
Control elements
1
2 6
10
8
ENA 5
5 en
Figure: Open cover
6
7
it
fr
The following nozzles are available from stockists and can be fitted to the
Connector System:
8 9 10 11
it
9
ENA 5
Proper use There is a risk of scalds and burns from the spouts
or the nozzle:
The machine has been designed and built for Z Place the machine out of the reach of
domestic use. It should only be used to prepare children.
coffee and to heat milk and water. Use for Z Do not touch any hot parts. Use the handles
any other purpose will be deemed improper. provided.
JURA cannot accept any responsibility for the Z Be careful to ensure that the appropriate
consequences of improper use. nozzle is correctly installed and clean. The
nozzle or parts of the nozzle could become
Keep this manual close to the ENA and pass it on detached if the parts are not assembled
to the next user if applicable. correctly or a blockage occurs.
10
ENA 5
Risk to children and persons with limited and pleasurable moments with the first choice for
capabilities in operating machines: perfect enjoyment.
Z The machine is not designed to be operated
by children and persons with limited Yours sincerely
capabilities.
Z The machine may only be used by persons
who are able to operate the machine safely.
Emanuel Probst
Safe handling of the CLARIS plus filter cartridges: General Manager
Z CLARIS plus filter cartridges should be kept
out of the reach of children.
Z Store the CLARIS plus filter cartridges in a dry JURA on the Internet
place in the sealed package. Visit us on the Internet.
Z Protect them from heat and direct sunlight.
Z Do not use damaged CLARIS plus filter @ At www.jura.com you will find the latest
cartridges. interesting information about your ENA and
en
Z Do not open CLARIS filter cartridges. all facets of the world of coffee.
11
ENA 5
Z Easy Cappuccino Frother 1 Preparing and using for the first time
U Cappuccino
This chapter provides the information you need
for trouble-free use of your ENA and gives you a
step-by-step guide to preparing your ENA for your
first coffee experience.
Supplied as standard
The following items are supplied as standard:
Z JURA ENA fully automatic coffee machine
Z 2-stage frothing nozzle Z Instructions for Use
U Cappuccino Z Filler funnel for pre-ground coffee
U Hot milk Z Measuring spoon for pre-ground coffee
Z CLARIS plus filter cartridge
Z JURA cleaning tablets
Z Aquadur test strip
Z Grinder key
Setting up
When setting up your ENA, please note the
following:
Z Place the machine on a horizontal surface
that cannot be damaged by water.
Z Select a position for the ENA where it is
protected against overheating.
12
ENA 5
T Remove the water tank and rinse with cold k T Press the Rotary Switch to confirm the
water. language setting.
T Fill the water tank with cold, fresh water
and replace the tank.
CAUTION
Coffee beans which have been treated with
additives (e.g. sugar), pre-ground or freeze-dried
coffee will damage the grinder. OK, the language is then adjusted.
T Only use untreated coffee beans to refill the OPEN TAP
bean container. T Place a receptacle under the nozzle.
it
First-time use
l T Turn the switch to position m.
E The on/off button also acts as a power SYSTEM FILLING
switch. When the ENA is switched off, the CLOSE TAP
machine is completely disconnected from y T Turn the switch to position o.
the power supply. HEATING de
PRESS ROTARY
J WARNING T Place a receptacle under the coffee spout.
If the machine is operated with a defective power k T Press the Rotary Switch to start rinsing.
cable, there is a danger of electric shock. RINSING
T Never use a machine which has a defective READY
power cable. fr
E When a coffee speciality has been
Precondition: The water tank must be full. prepared for the first time, it is possible
T Insert the mains plug into a power socket. that FILL BEANS appears on the
Q T Press the on/off button to switch the display as the grinder has not yet been
machine on. completely filled with coffee beans. In this
SPRACHE DEUTSCH case prepare a different coffee speciality. it
g T Turn the Rotary Switch until LANGUAGE
ENGLISH is displayed.
13
ENA 5
Example: Changing the water hardness from Z Select a coarse setting for a darker roast.
16 dH to 25 dH .
Precondition: READY appears on the display.
T Open the cover behind the Rotary Switch.
P T Press the P button until MAINTENANCE
appears.
g T Turn the Rotary Switch until HARDNESS
is displayed.
k T Press the Rotary Switch to enter the
programme item.
16 dH Example: Adjusting the fineness of grind during
g T Turn the Rotary Switch until 25 dH is coffee preparation.
displayed. T Place the cup under the coffee spout.
k T Press the Rotary Switch to confirm the k T Press the Rotary Switch to start coffee
setting. preparation.
OK, the water hardness is then adjusted. T Turn the fineness of the grinding wheel to
en
HARDNESS the desired position while the grinder is
g T Turn the Rotary Switch until EXIT is running.
displayed.
k T Press the Rotary Switch to exit program-
ming mode.
READY it
Adjusting grinder
You can adjust the grinder continuously to suit
the roast of your coffee.
1 CUP, the pre-set amount of water de
CAUTION flows into the cup, preparation stops
If you adjust the fineness of grind when the automatically.
grinder is not operating, the grinding wheel could READY
be damaged.
T Only adjust the fineness of grind when the
grinder is running. Switching on the machine fr
When the ENA is switched on, a prompt to
Our recommendations: perform a rinse operation automatically appears.
Z Select a fine setting for a light roast.
Q T Press the on/off button to switch the
ENA on.
HEATING it
PRESS ROTARY
T Place a receptacle under the coffee spout.
15
ENA 5
k T Press the Rotary Switch to start rinsing. In addition to the simple preparation at the touch
RINSING, the system is being rinsed. of a button, you can also adapt the coffee or
The operation stops automatically. espresso to suit your own individual taste. Various
READY setting options are provided to this purpose.
Give it a try:
Z Coffee strength: The coffee strength can be
Switching off the machine changed before preparation or during the
When the ENA is switched off, the system is grinding operation by turning the Rotary
automatically rinsed if a coffee speciality has been Switch. This setting changes the quantity of
prepared. coffee powder. The more coffee powder you
use to make the coffee, the stronger and
T Place a receptacle under the coffee spout. more intense the coffee speciality will taste.
T Turn the coffee spout to the cleaning Z Fineness of grind: In the ENA the coffee
position. beans are freshly ground each time a coffee
speciality is prepared. The fineness of grind
can be adjusted during the grinding
operation. Select a finer grind for espresso
than for coffee. The fineness of grind affects
the time the water requires to run through
the coffee powder. A finer coffee powder
prolongs the extraction time so that the
maximum aroma is released when espresso is
prepared.
Q T Press the on/off button. Z Temperature: The ENA programming mode
RINSING, the system is being rinsed, allows you to adjust the temperature for
the operation stops automatically. The ENA different coffee specialities. The temperature
is switched off. can affect the taste of the coffee and must be
T Turn the coffee spout to the 1 cup or 2 cup adapted to suit individual tastes and the type
position. of coffee bean.
Z Height-adjustable coffee spout: The height
E The On/Off button also acts as a power of the coffee spout can be adjusted on a
switch. When the ENA is switched off, the continuous scale as required to suit the size of
machine is completely disconnected from your coffee cups. The distance between the
the power supply. coffee spout and the edge of the cup should
be as small as possible. This prevents coffee
splashing on the machine and produces a
2 Preparation fine, thick crema.
16
ENA 5
it
T Place two cups under the coffee spout.
g T Turn the Rotary Switch until 2 CUPS
is displayed.
17
ENA 5
T Place one level measuring spoon of Precondition: READY appears on the display
pre-ground coffee into the filler funnel. and the coffee spout is set at the 1 cup position.
T Remove the filler funnel. T Place the cup under the coffee spout.
T Close the powder chute. g T Turn the Rotary Switch until STRONG is
1 CUP displayed.
k T Press the Rotary Switch to start coffee k T Press the Rotary Switch until STRONG is
preparation. displayed.
1 CUP, the pre-set amount of water During grinding the coffee strength
flows into the cup, preparation stops STRONG is displayed.
automatically. 1 CUP, the pre-set amount of water
READY flows into the cup, preparation stops
automatically.
E It is also possible to prepare two cups of READY
pre-ground coffee. To this purpose place
two level measuring spoons of pre-ground
coffee into the filler funnel. Turn the Rotary Entering a default setting for the amount of
Switch to 2 CUPS and press to start water for a cup size
coffee preparation.
E A default setting can be entered for the
amount of water for 1 coffee. When
One-off setting before and during preparing 2 coffees this amount is
preparation dispensed per cup.
The coffee strength can be changed before
preparation or during the grinding operation. Precondition: READY appears on the display
and the coffee spout is set at the 1 cup position.
The following coffee strength options are possible T Place the cup under the coffee spout.
for 1 coffee: k T Press the Rotary Switch and hold it down.
Z Mild During grinding the strength of the coffee
Z Normal is displayed.
Z Strong k T Continue to hold the Rotary Switch down
until ENOUGH COFFEE ? appears.
E 2 coffees are always prepared with the The coffee flows into the cup.
coffee strength mild. k T Press the Rotary Switch again when enough
E The pre-set amount of water can be coffee has been filled into the cup.
changed during the brewing operation by OK, the default setting for the amount of
turning the Rotary Switch. water for one coffee has been entered.
READY
One-off settings before and during coffee
preparation always follow this model. These E This setting can be changed at any time by
settings are not saved. repeating the above procedure.
18
ENA 5
it
g T Turn the Rotary Switch until STEAM is
displayed.
k T Press the Rotary Switch.
HEATING
READY appears as soon as the ENA is
sufficiently heated. g T Turn the Rotary Switch until STEAM is de
l T Turn the switch to position m. displayed.
STEAM , the milk foam is being prepared. k T Press the Rotary Switch.
y T Turn the switch clockwise to position o HEATING
when there is sufficient milk foam in the READY appears as soon as the ENA is
cup. sufficiently heated.
l T Turn the switch to position m. fr
E You can prepare more milk foam within STEAM , the milk foam is being prepared.
about 40 seconds. y T Turn the switch clockwise to position o
when there is sufficient milk foam in the
T Place the cup under the coffee spout. cup.
k T Press the Rotary Switch to start coffee
preparation. E You can prepare more milk foam within it
1 CUP, the pre-set amount of water about 40 seconds.
flows into the cup. Preparation stops
automatically.
19
ENA 5
T Place the cup under the coffee spout. y T Turn the switch to position o when the
k T Press the Rotary Switch to start the coffee milk foam has reached the required
preparation. consistency.
1 CUP, the pre-set amount of water
flows into the cup. Preparation stops E You can prepare more steam within about
automatically. 40 seconds.
To ensure that the Easy Cappuccino Frother T Place the cup under the coffee spout.
works perfectly, it should be rinsed and k T Press the Rotary Switch to start coffee
cleaned regularly (refer to Chapter 4 preparation.
Maintenance Easy Cappuccino Frother). 1 CUP, the pre-set amount of water
flows into the cup. Preparation stops
automatically.
Cappuccino with the 2-stage frothing nozzle
Precondition: READY appears on the display To ensure that the 2-stage frothing
and the coffee spout is set at the 1 cup position. nozzle works perfectly, it should be
T Push the 2-stage frothing nozzle to the rinsed regularly (refer to Chapter 4
lower position. Maintenance Dismantling and rinsing
T Place a cup of milk below the 2-stage the 2-stage frothing nozzle).
frothing nozzle and immerse the nozzle in
the milk.
Heating milk with the
Professional Cappuccino Frother
Precondition: READY appears on the display.
T Remove the protective cover from the
Professional Cappuccino Frother.
T Connect the milk pipe to the nozzle.
T Insert the other end of the milk pipe into a
milk carton or connect it to a milk
container.
E If the nozzle does not reach into the cup, lift T Place a cup under the nozzle.
the cup towards the nozzle. T Set the selector lever of the nozzle to the
milk t position.
g T Turn the Rotary Switch until STEAM is
displayed.
k T Press the Rotary Switch.
HEATING
READY appears as soon as the ENA is
sufficiently heated.
l T Turn the switch to position m.
STEAM , the milk is foamed by the hot
steam.
20
ENA 5
g T Turn the Rotary Switch until STEAM is k T Press the Rotary Switch.
displayed. HEATING
k T Press the Rotary Switch. READY appears as soon as the ENA is
HEATING sufficiently heated.
READY appears as soon as the ENA is l T Turn the switch to position m.
sufficiently heated. STEAM , the milk is heated by the hot
l T Turn the switch to position m. steam.
STEAM , the hot milk is being prepared. y T Turn the switch to position o as soon as
y T Turn the switch clockwise to position o the required temperature is reached.
when there is sufficient milk in the cup.
E You can prepare more steam within about
E You can prepare more hot milk within 40 seconds.
about 40 seconds.
To ensure that the 2-stage frothing
To ensure that the Professional Cappuccino nozzle works perfectly, it should be
Frother works perfectly, it should be rinsed rinsed regularly (refer to Chapter 4
en
and cleaned regularly (refer to Chapter 4 Maintenance Dismantling and rinsing
Maintenance Professional Cappuccino the 2-stage frothing nozzle).
Frother).
Hot water
Heating milk with the 2-stage frothing it
nozzle E To prepare hot water, attach either the hot
Precondition: READY appears on the display. water nozzle or the 2-stage frothing nozzle
T Push the 2-stage frothing nozzle to the top to the Connector System.
position.
T Place a cup of milk below the 2-stage J CAUTION
frothing nozzle and immerse the nozzle in There is a danger of scalding from hot water de
the milk. splashes.
T Avoid direct contact with the skin.
21
ENA 5
23
ENA 5
Example: Changing the language from U Wipe the surface of the machine with a
ENGLISH to FRANCAIS. damp cloth.
Precondition: READY appears on the display. U Rinse the nozzle regularly if it is used to
T Open the cover behind the Rotary Switch. warm or froth milk.
P T Press the P button until MAINTENANCE
appears.
g T Turn the Rotary Switch until LANGUAGE Rinsing the machine manually
is displayed. When the ENA is switched on, a prompt to
k T Press the Rotary Switch to enter the perform a rinse operation automatically appears
programme item. after heating. When the ENA is switched off, the
ENGLISH system is automatically rinsed if a coffee speciality
g T Turn the Rotary Switch until FRANCAIS has been prepared.
is displayed.
k T Press the Rotary Switch to confirm the The Rinse machine operation can be manually
setting. initiated.
OK, the language is then adjusted.
LANGUE Precondition: READY appears on the display.
g T Turn the Rotary Switch until EXIT is T Turn the coffee spout to the cleaning
displayed. position.
k T Press the Rotary Switch to exit program-
ming mode.
PRET
4 Maintenance
24
ENA 5
Changing the filter following a prompt E Rinsing of the filter can be interrupted at
any time. To this purpose turn the switch
E After 50 litres of water have flowed through clockwise.
the filter, its capacity is reached. The ENA E The water may be slightly discoloured. This
automatically prompts you to replace the is not harmful to health and does not affect
filter. the taste.
E After two months the filter capacity is
reached. The elapsed time can be checked Rinsing of the filter stops automatically,
with the date plate on the cartridge holder. CLOSE TAP.
E If the CLARIS plus filter cartridge is not y T Turn the switch to position o.
activated, you will not be prompted to HEATING
change the filter. READY
25
ENA 5
E The cleaning programme only lasts about T Close the powder chute for pre-ground
15 minutes. coffee.
E Do not interrupt the cleaning programme. PRESS ROTARY
The quality of cleaning will be impaired if k T Press the Rotary Switch.
you do so. CLEANING, water flows out of the
E JURA cleaning tablets are available from coffee spout several times.
stockists. EMPTY TRAY
T Empty the coffee grounds container and
Precondition: CLEAN / READY is displayed. drip tray and replace.
T Open the cover behind the Rotary Switch. READY
c T Press the maintenance button. T Turn the coffee spout to the 1 cup or 2 cup
EMPTY TRAY position.
T Empty the coffee grounds container and
drip tray and replace.
PRESS ROTARY Cleaning the machine manually
T Turn the coffee spout to the cleaning The Clean machine operation can be manually
position. initiated.
26
ENA 5
J CAUTION
If the descaling agent comes into contact with the
skin or eyes, this can cause irritation.
T Avoid contact with the skin or eyes.
T Rinse the descaling agent off with clean
water. Should you get any descaling agent
in your eye, consult a doctor.
y T Turn the switch to position o. T Place another receptacle under the nozzle.
DE-SCALING, the descaling operation T Set the selector lever of the nozzle to the
is continued. milk foam p or milk t position.
EMPTY TRAY
T Empty the coffee grounds container and
drip tray and replace.
T Reattach the nozzle to the Connector
System.
READY
T Remove the milk pipe from the milk carton T Remove the milk pipe from the milk carton
or milk container. or milk container.
T Fill a receptacle with fresh water and T Pour 250 ml of fresh water into a receptacle
immerse the milk pipe in the water. and add one capful (max. 15 ml) of the
Auto-Cappuccino Cleaner.
28
ENA 5
T Immerse the milk pipe in the receptacle. Dismantling and rinsing the
T Place another receptacle under the nozzle. Professional Cappuccino Frother
T Set the selector lever of the nozzle to the T Carefully remove the Professional Cappuc-
milk foam p or milk t position. cino Frother from the Connector System.
T Dismantle the frother completely.
29
ENA 5
g T Turn the Rotary Switch until STEAM is g T Turn the Rotary Switch until STEAM is
displayed. displayed.
k T Press the Rotary Switch. k T Press the Rotary Switch.
HEATING HEATING
READY appears as soon as the ENA is READY appears as soon as the ENA is
sufficiently heated. sufficiently heated.
l T Turn the switch to position m. l T Turn the switch to position m.
STEAM , the nozzle and pipe are rinsed. STEAM , the nozzle and pipe are cleaned.
y T Turn the switch to position o as soon as y T Turn the switch clockwise to position o as
clean water flows into the receptacle. soon as the receptacle holding the Auto-
Cappuccino Cleaner is empty.
T Rinse the receptacle thoroughly, fill with
Cleaning the Easy Cappuccino Frother 250 ml of fresh water and immerse the milk
To ensure that the Easy Cappuccino Frother works pipe in the water.
perfectly, you should clean it daily when you have T Empty the receptacle under the nozzle and
been preparing milk. replace under the nozzle.
g T Turn the Rotary Switch until STEAM is
CAUTION displayed.
If the wrong cleaning agent is used, the machine k T Press the Rotary Switch.
could be damaged and/or detergent residues HEATING
could be left in the water. READY appears as soon as the ENA is
T Only use original JURA care products. sufficiently heated.
l T Turn the switch to position m.
E The ENA will not prompt you to clean the STEAM , the nozzle and pipe are rinsed
Easy Cappuccino Frother. with fresh water.
E The JURA Auto-Cappuccino Cleaner is y T Turn the switch clockwise to position o
available from stockists. as soon as the receptacle holding
the water is empty.
T Remove the milk pipe from the milk carton
or milk container.
T Pour 250 ml of fresh water into a receptacle Dismantling and rinsing the
and add one capful (max. 15 ml) of Auto- Easy Cappuccino Frother
Cappuccino Cleaner. T Carefully remove the Easy Cappuccino
T Immerse the milk pipe in the receptacle. Frother from the Connector System.
T Place another receptacle under the nozzle. T Dismantle the nozzle completely.
30
ENA 5
31
ENA 5
T Place the finger guard into the bean 5 CLARIS plus filter cartridge Water
container and screw tight. for perfect coffee
T Fill the bean container with fresh coffee
beans, then close the bean container cover. Use of a CLARIS plus filter cartridge guarantees
you freshly filtered, delicious-tasting coffee and
hot water at all times. Designed specially for JURA
Cleaning the bean container coffee machines, it has a neutral pH value and is
Coffee beans may be covered with a slight oil film placed directly in the water tank.
which remains on the walls of the bean container. Unlike other water filtering systems for domestic
These residues may negatively affect the coffee use, CLARIS plus works according to the profes-
results. For this reason clean the bean container sional up-flow principle. In practical terms this
from time to time. means that only the precise amount of water
required for a given beverage is drawn in, and this
Q T Press the on/off button to switch the is filtered directly before use.
machine off.
T Disconnect the mains plug. No more descaling
T Remove the bean container cover. If you use the filter cartridge regularly, you will be
T Remove the coffee beans with a vacuum able to save yourself the time-consuming effort of
cleaner. regular descaling. Your coffee machine will also
T Clean the bean container with a soft, dry reward you with a longer service life. Use a CLARIS
cloth. plus filter cartridge if the water hardness is
T Fill the bean container with fresh coffee higher than 10 dH. You can determine the water
beans, then close the bean container cover. hardness before using your JURA coffee machine
for the first time with the Aquadur test strip
supplied with the machine.
Descaling the water tank
Limescale deposits may form in the water tank. Easy to operate
To ensure correct function of the machine, Inserting the CLARIS plus filter cartridge could not
descale the water tank from time to time. be easier. A description is contained in Chapter 1
Preparing and using for the first time Using and
T Remove the water tank. activating filter.
T If a CLARIS plus filter cartridge is used,
remove the cartridge. Economical use
T Descale the tank with a mild, commercially After 50 litres of water have been dispensed or
available descaling agent in accordance after two months at the latest, the filter capacity
with the instructions of the manufacturer. will be reached. The cartridge must then be
T Rinse the water tank thoroughly. replaced. Your JURA coffee machine will prompt
T If a CLARIS plus filter cartridge is used, you to change the filter. This procedure is
replace the cartridge. described in detail in Chapter 4 Maintenance
T Fill the water tank with cold, fresh water Changing the filter following a prompt.
and replace the tank.
You can return used filter cartridges to the
stockist.
32
ENA 5
it
de
fr
it
33
ENA 5
6 Display messages
34
ENA 5
7 Troubleshooting
35
ENA 5
Disposal
Please dispose of old machines in an environmen-
tally neutral way.
H
Old machines contain valuable materials which
should be salvaged for recycling. Please therefore
dispose of old machines via your regional
collection system.
36
ENA 5
fr
it
37
ENA 5
Index D
Descaling
2-stage frothing nozzle 9
JURA descaling tablets 27
Dismantling and rinsing 31
Machine 27
3-colour plain text display 12
Water tank 32
A Dismantling and rinsing
Adjusting 2-stage frothing nozzle 31
Energy-saving mode 22 Easy Cappuccino Frother 30
Grinder 15 Professional Cappuccino Frother 29
Language 23 Display 9
Units of water 23 Messages 34
Automatic switch-off 23 Disposal
Environmentally neutral disposal 36
B Drip tray 8
Barista tips 16
Bean container E
Cleaning 32 Easy Cappuccino Frother 8, 9
Filling 13 Cleaning 30
Dismantling and rinsing 30
C Rinsing 29
Cappuccino
With the 2-stage frothing nozzle 20 F
With the Easy Cappuccino Frother 19 Filter
With the Professional Cappuccino Changing 25
Frother 19 Using and activating filter 14
CLARIS plus filter cartridge First-time use 13
Water for perfect coffee 32 Foreign objects, Removing 31
Cleaning
Easy Cappuccino Frother 30
G
Grinder
Machine 25
Adjusting grinder 15
Professional Cappuccino Frother 28
Removing foreign objects 31
Coffee
Grinding wheel 9
At the touch of a button 17
Pre-ground 17 H
Coffee grounds container 8 Heating milk
Connector System 8, 11 With the 2-stage frothing nozzle 21
Contacts 37 With the Professional Cappuccino
Cover 9 Frother 20
Bean container 8 Hot water 21
Cup platform 8 Hot water nozzle 9
I
Internet
JURA on the Internet 11
Knowledge Builder 11
38
ENA 5
K S
Knowledge Builder 11 Safety
For your safety 10
M Settings
Machine Default, in programming mode 22
Cleaning 25 One-off setting, before and during
Descaling 27 preparation 18
Rinsing 24 Setting up 12
Switching off 16 Supplied as standard 12
Switching on 15 Switch-off
Maintenance 24 Automatic 23
Cleaning the bean container 32 Switch for hot water and steam preparation 8
Cleaning the machine 25 Symbol description 7
Descaling the machine 27 System, emptying 36
Descaling the water tank 32
Removing foreign objects 31 T
Rinsing the machine 24 Technical data 36 en
Tips 24 Transport 36
Troubleshooting 35
P
P button 9 U
Powder chute for pre-ground coffee 8 Use, proper 10
Preparation Using for the first time 12 it
Coffee 17
Pre-ground coffee 17 W
Preparing Water amount
Hot water 21 Default setting 18
Preparing and using for the first time 12 Water hardness
Professional Cappuccino Frother 9 Determining and adjusting 14
Water tank 8 de
Cleaning 28
Dismantling and rinsing 29 Descaling 32
Rinsing 28 Filling 12
Programming mode
Automatic switch-off 23
Prompt to take action fr
Symbol description 7
R
Rating plate 10, 36
Rinsing
Easy Cappuccino Frother 29
Machine 24 it
Professional Cappuccino Frother 28
Rotating coffee spout 8
39
ENA 5
Directives
The machine complies with the following EU
directives:
Z 73/23/EEC of 19 February 1973, Low Voltage
Directive including Amending Directive
93/68/EEC.
Z 89/336/EEC of 3 May 1989, Electromagnetic
Compatibility including Amending Directive
92/31/EEC.
Technical changes
We reserve the right to make technical changes.
Feedback
Your opinion is important to us!
Use the contact link at www.jura.com.
JURA Elektroapparate AG
Kaffeeweltstrae 10
CH-4626 Niederbuchsiten
www.jura.com
40