You are on page 1of 13

9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Chapter 5 Exam
Due Jul 7 at 7pm Points 20 Questions 20 Available Jul 7 at 7pm - Jul 11 at 12:59am 3 days
Time Limit None

A empt History
Attempt Time Score

LATEST Attempt 1 30 minutes 18 out of 20

Score for this quiz: 18 out of 20


Submitted Jul 9 at 9:51pm
This attempt took 30 minutes.

Question 1 1 / 1 pts

Which two statements are true about switched virtual interfaces (SVI) on a multilayer switch? (Choose
two.)

An SVI behaves like a regular router interface but does not support VLAN subinterfaces.

An SVI is a physical switch port with Layer 3 capability.

Correct! By default, an SVI is created for the default VLAN (VLAN1).

Correct! Only one SVI can be associated with a VLAN.

To create an SVI requires removal of Layer 2 port functionality with the no switchport
interface configuration command.

Question 2 1 / 1 pts

Refer to the exhibit. Based on the debug ip dhcp server packet output, which statement is true?

The client sends a DHCPDISCOVER that contains IP address 10.1.10.21 to the DHCP server.

https://1363293.netacad.com/courses/518689/quizzes/4414985 1/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

The client sends a DHCPREQUEST that contains IP address 10.1.10.21 to the DHCP server.

The client sends the BOOTREPLY broadcast message to inquire for a new IP address.

Correct! The client accepts the offer from the DHCP server for the 10.1.10.21 IP address.

Question 3 1 / 1 pts

Which statement describes what occurs when a DHCP request is forwarded through a router that has
been configured with the ip helper-address command?

The router replaces the source MAC address included in the DHCP request with its own MAC
address.

The router replaces the source IP address of the DHCP request with the IP address that is
specified with the ip helper-address command.

Correct!
The router replaces the broadcast destination IP address of the DHCP request with the
unicast IP address that is specified with the ip helper-address command.

The router replaces the unicast destination IP address of the DHCP request with the unicast
IP address that is specified with the ip helper-address command.

Question 4 0 / 1 pts

https://1363293.netacad.com/courses/518689/quizzes/4414985 2/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Refer to the exhibit. A network administrator attempts to ping the IP address 172.16.20.1 from RouterA.
What will the router output be?

You Answered Sending 5, 100-byte ICMP Echos to 172.16.20.1, timeout is 2 seconds:


!!!!!

Correct Answer Sending 5, 100-byte ICMP Echos to 172.16.20.1, timeout is 2 seconds:


.....

Sending 5, 100-byte ICMP Echos to 172.16.20.1, timeout is 2 seconds:


U.U.U

%network or host unreachable, TTL exceeded

%Unrecognized host or address, or protocol not running

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to


down

Question 5 1 / 1 pts

https://1363293.netacad.com/courses/518689/quizzes/4414985 3/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Refer to the exhibit and the partial configuration taken on routers RTA and RTB. All users can ping their
gateways, but users on VLAN 5 and VLAN 10 cannot communicate with the users on VLAN 20. What
should be done to solve the problem?

Correct! A dynamic routing protocol or static routes should be configured on the routers.

A trunk should be configured between routers RTA and RTB.

RTA interface Fa0/1 and RTB Fa0/1 should be configured with three subinterfaces, each with
ISL encapsulation.

RTA interface Fa0/1 and RTB Fa0/1 should be configured with three subinterfaces, each with
802.1Q encapsulation.

Question 6 1 / 1 pts

https://1363293.netacad.com/courses/518689/quizzes/4414985 4/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Refer to the exhibit. Which statement is true regarding the diagram and show ip route command output?

Because no routing protocol has been configured, the router will not forward packets between
workstations.

The default gateway for hosts on VLAN 10 should be the Fa0/0 IP address of the router.

Correct! The default gateway for hosts on VLAN 10 should be the Fa0/0.1 IP address of the router.

The default gateway for hosts on VLAN 10 should be the Fa0/0.2 IP address of the router.

Because their packets are being trunked, hosts on VLAN 10 do not need a default gateway.

Refer to curriculum topic: 4.1.2

Question 7 1 / 1 pts

https://1363293.netacad.com/courses/518689/quizzes/4414985 5/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Refer to the exhibit. What additional configuration is required for host A to receive IP configuration from
the DHCP server?

The ip address dhcp command is required on interface Fa0/0.

The ip dhcp information option command is required on interface Fa0/1.

Correct! The ip helper-address 10.1.2.10 command is required on interface Fa0/0.

The ip forward-protocol 37 global configuration command is required to forward DNS


requests to IP address 10.1.2.10.

The ip forward-protocol 67 global configuration command is required to forward DHCP


requests to IP address 10.1.2.10.

The ip forward-protocol 69 global configuration command is required to forward TFTP


requests to IP address 10.1.2.10.

Question 8 1 / 1 pts

A client computer is set up for DHCP and needs an IP configuration. During the DHCP client configuration
process, which response will enable the client to begin using the assigned address immediately?

Correct! DHCPACK

DHCPREQUEST

https://1363293.netacad.com/courses/518689/quizzes/4414985 6/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

DHCPOFFER

DHCPDISCOVER

Question 9 0 / 1 pts

Refer to the exhibit. A network administrator attempts to ping the IP address 172.16.20.1 from RouterA.
What will the router output be?

You Answered Sending 5, 100-byte ICMP Echos to 172.16.20.1, timeout is 2 seconds:


!!!!!

Correct Answer Sending 5, 100-byte ICMP Echos to 172.16.20.1, timeout is 2 seconds:


.....

Sending 5, 100-byte ICMP Echos to 172.16.20.1, timeout is 2 seconds:


U.U.U

%Unrecognized host or address, or protocol not running

%Source quench: destination or port unreachable

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/13, changed state to


down

Question 10 1 / 1 pts

https://1363293.netacad.com/courses/518689/quizzes/4414985 7/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Refer to the exhibit. The router has been properly configured for the trunking interface. Which statement is
true about the routing table on the router?

It will show a next hop address of the switch for both VLANs.

It will show one trunking route to 10.0.0.0/8.

Correct! It should contain routes to the 10.10.10.0/24 and the 10.10.11.0/24 networks.

Because the switch is not configured properly to trunk VLAN 1 and VLAN 2, the routing table
of the router will not show routes to either VLAN .

Because the switch port fa0/1 is in access mode, the routing table of the router will not show
any routes.

Question 11 1 / 1 pts

Which two statements are true about routed ports on a multilayer switch? (Choose two.)

A routed port behaves like a regular router interface and supports VLAN subinterfaces.

A routed port is a physical switch port with Layer 2 capability.

https://1363293.netacad.com/courses/518689/quizzes/4414985 8/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Correct! A routed port is not associated with a particular VLAN.

Correct!
To create a routed port requires removal of Layer 2 port functionality with the no switchport
interface configuration command.

The interface vlan global configuration command is used to create a routed port.

Question 12 1 / 1 pts

Which three statements about a routed port are true? (Choose three.)

A routed switch port is a physical device that is associated with several VLANs.

Correct!
A routed switch port is created by configuring a Layer 2 port with the no switchport interface
configuration command and assigning an IP address.

A routed switch port is created by entering VLAN interface configuration mode and assigning
an IP address.

A routed switch port is a virtual Layer 3 interface that can be configured for any VLAN that
exists on a Layer 3 switch.

Correct!
A routed switch port provides an interface that may provide a Layer 3 connection to a next-hop
router.

Correct! A routed switch port can serve as a default gateway for devices.

Question 13 1 / 1 pts

A DHCPREQUEST message has been sent from the client to the DHCP server. What information is
included in the message?

initial message to locate a DHCP server

Correct! formal request for the offered IP address

confirmation that the IP address has been allocated to the client

https://1363293.netacad.com/courses/518689/quizzes/4414985 9/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

denial message to reject the first offer from the DHCP server

Question 14 1 / 1 pts

Refer to the exhibit. Which configuration should be applied on router R1 in order for host 1 to receive its IP
configuration from the DHCP server?

ip helper-address 10.1.1.2 applied to the Fa0/0 interface

ip helper-address 10.1.1.3 applied to the Fa0/0 interface

ip helper-address 192.168.10.1 applied to the Fa0/0 interface

Correct! ip helper-address 10.1.1.1 applied to the Fa0/1 interface

ip helper-address 10.1.1.3 applied to the Fa0/1 interface

ip helper-address 192.168.10.1 applied to the Fa0/1 interface

Question 15 1 / 1 pts

Which message will be sent back to the client by the DHCP server to confirm that the IP address has
been allocated to the client?

DHCPDISCOVER unicast

DHCPDISCOVER broadcast

DHCPOFFER unicast

DHCPOFFER broadcast

https://1363293.netacad.com/courses/518689/quizzes/4414985 10/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

DHCPREQUEST unicast

DHCPREQUEST broadcast

Correct! DHCPACK unicast

Question 16 1 / 1 pts

A client sends a request for an IP address to a DHCP server. Which DHCP message to the client will
provide the configuration parameters that include an IP address, a domain name, and a lease for the IP
address?

DHCPDISCOVER

Correct! DHCPOFFER

DHCPREQUEST

DHCPACK

Question 17 1 / 1 pts

Refer to the exhibit. Host A is unable to obtain an IP address from the DHCP server. Which procedure
would solve this problem?

Use the command ip helper-address 10.1.2.1 on interface Fa0/0 of router RTA.

Correct! Use the command ip helper-address 10.1.2.10 on interface Fa0/0 of router RTA.

Use the command ip helper-address 10.1.2.10 on interface Fa0/1 of router RTA.

Use the command ip forward-protocol 67 on interface Fa0/0 of router RTA.

https://1363293.netacad.com/courses/518689/quizzes/4414985 11/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

Use the command ip forward-protocol 68 on interface Fa0/1 of router RTA.

Use the command ip forward-protocol 67 on interface Fa0/1 of router RTA.

Question 18 1 / 1 pts

Refer to the exhibit and the partial configuration taken on router RTA. Users on VLAN 5 cannot
communicate with the users on VLAN 10. What should be done to fix the problem?

A dynamic routing protocol should be configured on the router.

Two static routes should be configured on the router, each pointing to each subnet.

The Fa0/0 interface should be configured with a primary IP address of 10.10.5.1/24 and a
secondary IP address of 10.10.10.1/24.

Correct! The subinterfaces of the router should be configured with 802.1Q encapsulation.

Question 19 1 / 1 pts

How is the Layer 2 functionality restored to a port configured for Layer 3 operation?

switchport access vlan

switchport mode access

https://1363293.netacad.com/courses/518689/quizzes/4414985 12/13
9/7/2017 Chapter 5 Exam : 2017-TLM02_Q2-CCNP_SWITCH-LHC

no switchport

Correct! switchport

Question 20 1 / 1 pts

What is an advantage to using a trunk link to connect a switch to an external router that is providing inter-
VLAN routing?

Correct! works with any switch that supports VLANs and trunking

lowers latency

provides redundancy to the VLANs

reduces CPU overhead

Quiz Score: 18 out of 20

https://1363293.netacad.com/courses/518689/quizzes/4414985 13/13

You might also like