You are on page 1of 2

MasterEmaco N 907

Two component polymer modified fairing coat and re-profiling mortar

DESCRIPTION TYPICAL PROPERTIES


MasterEmaco N 907 is a two component acrylic
polymer modified blow hole filler and reprofiling Colour Light grey
mortar. It can be applied upto 10mm. Plastic density 1626kg/m
Working life at 25C Approx. 45 mins
MasterEmaco N 907 can be used as a skim ASTM D2471
coat prior to application of protective coatings. Compressive strength 20N/mm
BS EN 12190
Pull off bond strength >0.8N/mm
MasterEmaco N 907 is specially formulated to BS EN 1542 : 1999
produce a shrinkage compensated mortar with Rapid chloride permeability Very low
no cracking when applied in a thin section. ASTM C1202

PRIMARY USES PACKAGING


As a fairing or skim coat to cover and make Powder Component: 16.66kg bag
good blemishes in concrete surfaces such as Liquid Component: 5kg bottle
slight honeycombing, blowholes, sand runs, Total: 21.66kg or 13.3 litre packs
grout loss and shutter movement.
Preparatory treatment to concrete to receive APPLICATION PROCEDURE
a thin film protective coating.
To produce a uniform surface over repair
areas SURFACE PREPARATION
Surfaces to receive MasterEmaco N 907 should
ADVANTAGES be sound, clean and uncontaminated. The
surface should be mechanically prepared to
Precision made, consistent results. remove laitance. The surface should not be
Pre-gauged liquid, no mixing water. contaminated with oil, grease or paint.
Shrinkage compensated.
Flexible. SURFACE CONDITION
Smooth, easy to finish.
Surfaces should be thoroughly soaked prior to
Low permeability. application. Excess water should be removed
Excellent resistance to freeze/thaw and prior to application of MasterEmaco N 907.
action and carbonation.
Reduced ingress of water borne salts.
DEEP VOIDS
Greater economy of applied coatings
Deep voids should be filled with the correct
product from the MasterEmaco range
COMPOSITION
MasterEmaco N 907 is a specially formulated MIXING
blend of Portland cements, selected aggregates
and liquid acrylic in a plastic container. The pre- MasterEmaco N 907 is formulated to produce
packed components only require on site mixing an easily mixed mortar. A slow speed drill &
to produce a creamy, easily applied mortar. paddle can be used or a forced action mixer.
Add powder to liquid at a steady rate. Mix for
approx 4 minutes. Part mixing can be done
provided the ratio of 3.5:1 is observed.
MasterEmaco N 907

APPLICATION SPECIFICATION CLAUSE


MasterEmaco N 907 is applied by steel trowel. All slight surface imperfections should be made
The finishing should be carried out with the good by the application of MasterEmaco N 907
minimum trowelling. A small amount of water as manufactured by BASF. Applications should
can be applied to the surface to aid finishing. be strictly in accordance with the manufacturers
Leave the applied material for a short time instructions.
before applying a final trowel.
STORAGE
CURING Store out of direct sunlight, clear of the ground
Curing is generally not required however during on pallets protected from rainfall. Avoid
hot, dry and windy conditions the surfaces excessive compaction. Shelf life is 6 months
should be covered to prevent rapid drying. when stored as above.
Alternatively the applied material can be cured
with MasterKure 181. This product is NOTE
compatible with most subsequent coatings. Field service, where provided, does not
constitute supervisory responsibility. For
Note: In addition to shrinkage compensation, additional information contact your local BASF
this product has been designed to develop representative.
tensile strength sufficient to withstand the
internal stress generated by volume change to BASF reserves the right to have the true cause
reduce the incidence of drying shrinkage of any difficulty determined by accepted test
cracking. methods.

EQUIPMENT CARE QUALITY AND CARE


Tools should be washed with water immediately All products originating from BASFs Dubai, UAE
after use. facility are manufactured under a management
system independently certified to conform to the
COVERAGE requirements of the quality, environmental and
One unit of mixed MasterEmaco N 907 will occupational health & safety standards ISO
typically yield 13.3 litres of mortar. 9001, ISO 14001 and OHSAS 18001.

* Properties listed are based on laboratory controlled tests.

= Registered trademark of the BASF-Group in many countries.

BASF_CC-UAE/Em_N907_11_04/v3/05_16
The technical information and application advice given in this BASF publication are based on the present state of
STATEMENT OF our best scientific and practical knowledge. As the information herein is of a general nature, no assumption can be
RESPONSIBILITY made as to a product's suitability for a particular use or application and no warranty as to its accuracy, reliability or
completeness either expressed or implied is given other than those required by law. The user is responsible for
checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by BASF either
NOTE orally or in writing may be followed, modified or rejected by the owner, engineer or contractor since they, and not
BASF, are responsible for carrying out procedures appropriate to a specific application.

BASF Construction Chemicals UAE LLC


Disclaimer: the LRQA mark relates
P.O. Box 37127, Dubai, UAE to certified management system and
Tel: +971 4 8090800, Fax: +971 4 8851002 not to the product mentioned on this
www.master-builders-solutions.basf.ae datasheet

You might also like