Professional Documents
Culture Documents
Uses Properties
Brushbond provides a seamless, waterproof coating suitable Pot life : 30 min. at 270C
for use in water tanks, reservoirs, swimming pools, roofs
Mixed Density : 1.85-1.95 g/cc.
and to ensure water tightness.
(brushable consistency)
Brushbond effectively protects against concrete decay
Colours : Grey and white
providing a long lasting barrier to waterborne corrosive salts
and atmospheric gases. Application temperature : Not less than 100C
Brushbond is designed to re-face and even out variations in Toxicity : Non-toxic
concrete and masonry surfaces. Adhesion to concrete : >1N/mm2
Brushbond effectively seals concrete masonry walls and Brushbond provides an elastomeric protective waterproof
bridges the shrinkage cracks which are static. coating and is shown to resist positive hydrostatic pressure
Brushbond provides a tough and durable coating which upto 7 meter head. The degree of resistance of Brushbond
cannot be easily damaged or worn away. to water under pressure depends on the coating thickness.
Areas subjected to moderate and heavy loads/hydrostatic
Advantages pressure. minimum 2mm thickness coating is recommended
with screed above.
Minimum surface preparation needed - Low labour costs.
Application Instructions
Applied directly to the damp concrete and masonry
Excellent adhesion - Bonds to porous and nonporous Preparation
surfaces. All the surfaces which are to receive Brushbond, must be free
Non-toxic-ideal for potable water tanks from oil, grease, wax, dirt or any other form of foreign matter
which might affect adhesion. Spalled and deeply
Waterproof - Excellent for damp-proofing basements disintergrated concrete should be removed to sound concrete
Breathable-allows transmission of water vapour from and repaired with Renderoc System.
interior of building Mixing
Excellent for concrete roof, leaking brick and masonry Nitobond BB is poured into a plastic or metal drum. To this,
walls an equal volume of clean fresh water is added, for brush
Good resistance to Carbon dioxide and Chloride ion application consistency. Then mixing is started with a slow
diffusion speed drill (350-450 rpm). The powder component is added
gradually to the liquid avoiding lump formation and mixed for
Description 2-4 minutes. Mix and use. More material should not be mixed
than can be used within pot life. Retempering with water
Brushbond is a two component acrylic polymer modified
should not be done. Keep on stirring during application.
elastomeric waterproofing membrane which consists of
Brushbond powder and Nitobond BB acrylic emulsion. It Mixing Ratio
requires only the addition of water on site and when mixed in
the proper proportions, an easily brushable coating is Brushbond Components Indl.pack Small pack
produced. Brushbond can simply be applied by a stiff brush, Powder 23 kg 6 kg
or trowel to obtain the desired thickness.
Nitobond BB 4L 1L
Brushbond powder consists of specially selected cements,
graded hard-wearing aggregates and additives supplied in Water 4L 1L
powder and Nitobond BB liquid component of blended acrylic
copolymers.
Application
The polymer provides Brushbond with exceptional adhesion,
toughness and durability. For best results moisten the surface before coating with
Brushbond. Apply the mixed material using a short, stiff bristle
Brushbond
Technical Support brush preferably 100 to 150mm width like a paint. Trowel
applications can be undertaken as necessary using the
The company provides a technical advisory service supported correct mixing ratio to obtain satisfactory consistency.
by a team of specialists in the field.
Brushbond
Allow the Brushbond to dry before covering with screed. Allowances should be made for any possible wastages when
estimating.
Sprinkle coarse sand on wet surface of final coat for better
adhesion of screed.
Storage
Average drying time is 4 to 6 hours at normal temperatures.
Brushbond has a shelf life of 9 months in unopened packs, if
Subsequent Finishes
kept in a dry store. In high humidity locations, the shelf life
Brushbond provides an aesthetically pleasing surface finish may be reduced to less than 6 months. Prevent Nitobond BB
texture depending on the method of application, and does from freezing.
not normally require any further surface finishes.
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176
Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966
Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339
Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
INDIA/707/D
Brushbond Coolcoat constructive solutions
Uses Properties
Brushbond Coolcoat is designed for use as a thermal Appearance and colour White coloured, pasty
insulation coating on roof slabs and walls of buildings. It can consistency
also be used on the interior walls and the roof of freezer
Surface drying time 15 min - 20 min at 27C
rooms and cold storage facilities.
Brushbond Coolcoat can be applied on the following Over coating time 2 - 3 hours
substrates: Service temperature -30C to +90C
Concrete
Thermal conductivity
Asbestos sheet
Brushbond Coolcoat 0.1 W/ m 0C
weatherproof and roofing materials Normal Concrete 1.28 W/m 0C
Application area: Steel 16.0 W/m 0C
Note: High values indicate higher rate of transmission of
External and internal walls
heat
Cold storage facilities
Roof slabs Application instructions
Advantages Preparation
Minimum surface preparation needed All the surfaces which are to receive Brushbond Coolcoat
Single component - Brush or roller applied directly on the coating, must be free from oil, grease, wax, dirt or any other
substrate form of foreign matter which might affect adhesion. Spalled
and deeply disintegrated concrete should be removed to
Light weight yet effective
sound concrete and repaired with Renderoc system.
Excellent adhesion to most building substrates
Metal surface must be thoroughly abraded to ensure proper
Low thermal conductivity reduces energy consumption
mechanical key.
Durable - High UV resistance
Mixing
Description
Add 800ml clean water per pack of 4 L of Brushbond Coolcoat
and mix thoroughly using a slow speed drill fitted with a paddle.
Brushbond Coolcoat is a water-based white coloured
emulsion comprising of polymers and specially designed Priming
hollow microspheres, less than 100 microns in diameter
Priming is not required on metallic and non porous surfaces.
with non conductive properties.
On highly porous cementitious surfaces, apply a slurry coat
These microspheres collectively acts as thermal insulation made with 1:1:3 (Nitobond SBR:Water:Cement) using a clean
blanket covering the structure effectively reflecting solar roller/brush and allow the surface to dry for atleast 2-3 hours.
radiation back into the atmosphere. This results in impressive
Application
temperature reduction behind the substrate.
Once the sealer coat has dried, the Brushbond Coolcoat
Technical support system shall be applied using a brush/roller or by a suitable
spray equipment. Allow the surface to dry for atleast 2-3 hours
The company provides a technical advisory service supported before applying the second coat.
Brushbond Coolcoat
Estimating Limitations
A minimum of 2 coats are recommended for effective Brushbond Coolcoat system is non-toxic but alkaline in nature.
performance. Allowances should be made for any possible Gloves and goggles should be worn while handling. Any
wastages when estimating. splashes on the skin or eyes should be washed off with clean
water. In the event of prolonged irritation, medical advice should
Storage be sought. Brushbond Coolcoat system is non- flammable.
Shelf life
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176
Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966
Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339
Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
INDIA/0852/A
Brushbond RFX constructive solutions
The application of Brushbond RFX should not be done if the Consistency Brush application
temperature of the substrate is below 100C. When applying
Brushbond RFX on hot substrates i.e., over 300C surface Coverage (15kg + 4.8 L pack) 12 - 14m2
temperature, saturate the surface with water. Apply Brushbond Coverage (5 + 1.63 L pack) 4 - 4.5m2
RFX in 2 coats to achieve 1mm thickness. The second coat of Storage
Brushbond RFX shall be applied as soon as the first coat has
Shelf life
reached touch dry state. It is recommended that for general
surfacing Brushbond RFX should be applied at a minimum 9 months in unopened packs if kept in a dry store.
thickness of 1mm. Areas subjected to moderate and heavy
loads/hydrostatic pressure, minimum 2mm thickness coating Precautions
is recommended with screed above. Health and Safety instruction
Allow the Brushbond RFX coating to dry before covering with
Brushbond RFX is non-toxic but alkaline in nature. Gloves
screed. Sprinkle coarse sand on wet surface of final coating for
and goggles should be worn. Any splashes to the skin or
better adhesion of screed.
eyes should be washed off with clean water. In the event of
Average drying time is 4 to 6 hours at normal temperatures. prolonged irritation, seek medical advice. Use a dust mask
Cleaning while handling the powder.
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176
Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966
Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339
Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
INDIA/708/F
Brushbond TGP constructive solutions
(Formerly known as Tegraproof C)
Technical support times daily for the 48 hour period. For warmer climates, more
frequent spraying may be required. It is important to keep the
The company provides a technical advisory service supported Brushbond TGP* crystalline waterproofing system moist to
by a team of specialists in the field. allow the crystal formation to occur. The surfaces shall be
protected from foot traffic for 48 hours or heavy traffic for 7
Brushbond TGP*
Estimating
Supply
Brushbond TGP : 15 kg bags
Coverage
Brushbond TGP : 1.0 to 2.0 kg/m2 per application (brush)
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176
Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966
Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339
Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
INDIA/737/G
Brushbond TI Flexicoat constructive solutions
Brushbond TI Flexicoat is designed for use as a thermal The company provides a technical advisory service supported
insulation coating on roof slabs and walls of buildings. It can by a team of specialists in the field.
also be used on the interior walls and the roof of freezer
rooms and cold storage facilities. Properties
Description Preparation
This system also has certain waterproofing properties and Add 20% clean water (i.e. 4 litres of clean water to the 20 litre
is able to bridge hairline cracks caused by thermal container) and mix thoroughly using a slow speed drill fitted
movements. with a paddle.
Brushbond TI Flexicoat
Once the sealer coat has dried, the Brushbond TI Flexicoat Brushbond TI Flexicoat system has a shelf life of 6 months in
system shall be applied using a brush/roller or by a suitable unopened packs, if kept in a cool dry store.
spray equipment. Allow the surface to dry for atleast 2-3 hours
before applying the second coat. Limitations
Packaging Precautions
Brushbond TI Flexicoat system is supplied in 4 L and 20 L packs. Health and Safety instructions
Coverage Brushbond TI Flexicoat system is non-toxic but alkaline in
This depends on the roughness & porosity of the substrate. The nature. Gloves and goggles should be worn while handling.
approximate coverage 2.5 - 3.0 m2/coat /L after dilution on Steel Any splashes on the skin or eyes should be washed off with
or Concrete surfaces. clean water. In the event of prolonged irritation, medical advice
should be sought. Brushbond TI Flexicoat system is non-
Though diluted, for workability purpose, extra yield in material flammable.
per pack shall not be used for extended coverage.
Ahmedabad : (079) 26762799 Ankleshwar :(02646) 220704/224687 Bellary: 09845891690 Bhubaneshwar : (0674) 2521176
Chennai : (044) 24899949/24853383 Chandigarh : (0172) 2639360 Cochin : (0484) 2347465 Coimbatore : (0422) 2472966
Goa : (0832) 09423058696 Guwahati : (0361) 2462866 Hyderabad : (040) 27662324/27662425 Indore : (0731) 4049339
Jaipur : (0141) 2336103 Lucknow :(0522) 2239044 Nagpur: (0712) 2753510/2563242 Visakhapatnam : (0891) 2564850 / 2707607
INDIA/0847/D