‘Datais required by M/s. L&T for Incoming power supe for Tradion sub station Bhayal(OFCC)
2 [Name of 3s f2dkv Bhayal(OFCC)
2 [orce Cranage: NA,
3 [Electric Supply Utity [cerca
‘4 Jadiress/Location of G55 220kv Gavased S[s, Ta Padra, Dist Vadodare- 391830,
3 [Contact offices SE(TR), GETCO, Circle Ofice, Jambuva, Vadodara 300014
Iseno. Requested information Pavtialars
T_ |[sTermination/incomime Tower paraled to Teck & Supply |To be decided ater receipt of layout of substation of Rallway
Lines Pecpendicular to track?
3 [single line diagram i attached,
Hasall the drawings of incomimg power supply
arrangements from Electric Supply Utlity collected?
linclucing of transmission lines, gr Substation & Ganty)
3-_Distance of source of supply from SS ose aK
4 f2z0kv Zebra Conductor
1z9=0.096 +) 0.397= 0.403 1 80.05" n/m
Impedance Characteristic of supply Lines{Ohms) Jzo=0.208 + 1334=1.349 81.3" O/km
5 [Provision of Lighting arrestors on outgoing lines from GSS, _|3 units of 65 kv per phase.
Make & Ratings. ]Make-Lamco Industries Private Limited,
ating: 66KV, 10 KA
Presuce Relief Current- 40 KA
|Rating of feeding Wansformer [220/66 kv, aXSOMVA= 150 MVA capacity
Hv Amp-131.4,131.2,131.22
Lv amp-437.9,437.4,437.4
sé impedance-14.87,18.82,14.3
7 |itake, Type & rating of feeder Circlt Breaker feeding the — |Make- Siemens
Dedicated power to railway traction [Type-3aPa
ated Voltage-248 ky
Rated Normal curent-4000A,
Rated short circuit current SOKA
[Rated Operating sequence- 0-0.35-CO-3min-cO.
| Time settings ofthe feeder creult breakers of GSS orco- [It will be decided at the time of charging.
ordination of TSS protection with Upstream GSS
9 [Short Great Fault Curent Level(KA) [220kv Gavasad 7s
ns.92 ba, 7589.51 Miva
10. [Protection Settings of the Relaying Sytem [Both Distance Scheme Time Delay
instantaneous, MT & TMS} for al types. 0% protected line 350 msec
[22=150% tine (Double circuit) 750 msec
200%120 % 500 msec
IMi= Micom P44, M2=GEOGO
TI [Restriction of Harmonies/unbalance imposed by SEB [248 = 10% protection line
[2 Restriction for harmonics
[2% Voltage unbalance
12. [Detail drawing of termination towers Indicating local height [GA drawing of 220 kv Tower attached
and distance of cross arm from top of foundation
13 [Dimensions of conductor and tension used for stinging with |ACSR Zebra conductor (GTP attached)
rss incoming gantey
74 [exposure of termination tower foundation fom ground level [200 mm (foundation drawing attached)“ax TNauoo NoIseINSNYAL OWEN LVAVENS
WO+dG. SdAL HAMOL
ToenoTe /
NOILVONNOS ® /
SOIASC ONIHLY va JO STIVLAG
smowannsHin sa
a Low ALMO AAV3HO
4 —_
uh Comet oun
T i} a —:GETCOVE/TS-CONOS2/R2DT. 30107/2008
GUARANTEED TECHNICAL PARTICULARS FORACSR ZEBRA?
CONDUCTOR
The Guaranteed Technical particulars furnished below shall be duly attested by the
Bidder. Any correction / alterations in this GTP will lead to out right rejection of
the Bid.
Sr. | Description ‘Alumunium Steel
No
1)__| Number Of Strands —Nos. 34 7
2) _ | Diameter Of Strand—mm.
1) Strands
0) Nominal 3.18 3.18
p) Maximum 3.21 3.24
) Minimum 3.15 3.12
11) Overall Of Conductor 28.62
3) _ | Cross Sectional Area Of Sq.
mn.
e) Whole Conductor 484.5
f) Each Strand 7.94 7.94
4) _ | Laying Of Strands —Nos.
h) Center NA. 1
i) First Layer 12 6
i) Second Layer 18 NA.
k)_Third Layer 24 NA.
3) _ | Weight (Exel. Wt. Of Grease)
~Kg/Km.
2) Whole Conductor 1621
h) Strand (At Nominal Dia.) [21.47 61.95
6) | Calculated D.C. resistance at
20°C - Ohms / Km
g) Whole Conductor 0.06868 NA.
h) Strand 3.626 NA.
7) _ | Ultimate Tensile Stress — KN
g) _ Whole Conductor 130.30 NA.
h) Strand
vii) Before Stranding | 1.29 10.43
viii) After Strandin, 1.23 991
8) _ | Modulus of Elasticity —
d) Kg/Sq. Cm. 07036x10°
°)
9) | Coefficient of linear expansion ] 19.3x10° 11. 5xi0*-6
= per deg. C. lGETCO/B/TS-CON0S2/R2DT. 30/07/2008
10) | Chemical Composition - %
v) EC Grade Al
w) Copper (Max.)
x) Carbon
y) Manganese
2) Phosphorous
aa) Sulphur
bb) Silicon
99.5
0.04
NA
NA
NA
NA
NA
NA
NAL
0.50 -0.85
0.50-1.10
‘Max. 0.035
Max. 0.045
0.10 0.35
Ti | Grease Make
Protectilo ~ 56 -57 or Rustilo~
442
‘As per IS 398 (Part — 2) 1996 Neutral
Grease between the layers of steel
12)_| Zine Purity - %
T3) | Resistivity — Ohms Sq. mm / 0.028264 WB.
Mr.
14)_[ Density (At 20°C) - Gm/ 2.703 7.80
Cucm:
15) _| Constant Mass Temp. Co- 0.004 WA.
efficient Of resistance ~ Per®C
16)* | Lay Ratios
g) First Layer
i) Maximum 17 28
ii)Minimum 10 13
h) Second Layer
pi) Maxi 16
10 NLA.
i) Third Layer
qi) Maximum 14
ii)Minimum, 10 NA
17) | Elongation (Minimum) -% NA, a
Before stranding