Professional Documents
Culture Documents
--------------------------------
Connection Template : DA BCF Weld support Bolt beam
Connection ID : BCF - N(9) - M(27,34)
Design Code: AISC-ASD
Status:: NotGood
------------------------------------------------------------------------
--------------------------------
LOADS
Members Load Type V2
V3 M33 M22 Axial
[Kip]
[Kip] [Kip*ft] [Kip*ft] [Kip]
------------------------------------------------------------------------
--------------------------------
Beam LC-1 Design -0.01
-- -- -- -0.09
LC-2 Design 0.01
-- -- -- 0.09
LC-3 Design -1.34
-- -- -- -3.69
LC-4 Design -1.93
-- -- -- -5.29
LC-5 Design 4.45
-- -- -- 12.22
LC-6 Design 2.12
-- -- -- 4.66
LC-7 Design 4.49
-- -- -- 12.23
LC-8 Design 1.68
-- -- -- 7.29
LC-9 Design 0.06
-- -- -- -0.94
LC-10 Design -0.06
-- -- -- 0.94
LC-100 Design -3.27
-- -- -- -8.98
LC-101 Design 3.11
-- -- -- 8.54
LC-102 Design 0.78
-- -- -- 0.98
LC-103 Design 3.15
-- -- -- 8.54
LC-104 Design 0.34
-- -- -- 3.61
LC-107 Design -1.35
-- -- -- -3.74
LC-108 Design -1.33
-- -- -- -3.63
LC-109 Design -2.79
-- -- -- -7.70
LC-110 Design -2.78
-- -- -- -7.61
LC-111 Design 0.55
-- -- -- 1.51
LC-112 Design -1.20
-- -- -- -4.16
LC-113 Design 0.58
-- -- -- 1.52
LC-114 Design -1.52
-- -- -- -2.18
LC-117 Design 3.65
-- -- -- 10.01
LC-118 Design 1.32
-- -- -- 2.45
LC-119 Design 3.69
-- -- -- 10.01
LC-120 Design 0.88
-- -- -- 5.08
LC-123 Design -0.81
-- -- -- -2.27
LC-124 Design -0.80
-- -- -- -2.15
LC-125 Design -2.79
-- -- -- -7.65
LC-126 Design -1.34
-- -- -- -3.69
LC-127 Design -1.34
-- -- -- -3.69
LC-128 Design -3.27
-- -- -- -8.98
LC-129 Design -3.27
-- -- -- -8.98
------------------------------------------------------------------------
--------------------------------
GEOMETRIC CONSIDERATIONS
Dimensions Unit Value Min.
value Max. value Sta. References
------------------------------------------------------------------------
--------------------------------
Angle
Length [in] 8.50 5.36
10.72 p. 10-8
Lmin = T/2 = 10.720472[in]/2 = 5.360236[in] p. 10-8
Lmax = d - max(k, dct) - max(k, dcb) = 11.984252[in] - max(0.63189[in], 0[in]) -
max(0.63189[in], 0[in]) = 10.720472[in] p. 10-8
Beam
Horizontal edge distance [in] 2.75 1.00
-- TablesJ3.4,J3.5
Lemin = edmin + C2 = 1[in] + 0[in] = 1[in] Tables J3.4,
J3.5
WARNINGS
Connector does not fit on
support
------------------------------------------------------------------------
--------------------------------
DESIGN CHECK
Verification Unit Capacity Demand
Ctrl EQ Ratio References
------------------------------------------------------------------------
--------------------------------
Angle (Beam side)
Bolts shear [Kip] 63.65 13.02
LC-7 0.20 Tables (7-1..14)
(1/W)Rn = (1/W)*Fnv*Ab = 0.5*48[Kip/in2]*0.442[in2] = 10.608[Kip] Eq. J3-1
(1/W)Rn = 2 * (C*(1/W)Rn) = 2 * (3*10.608[Kip]) = 63.648[Kip] Tables (7-1..14)
Beam
Bolt bearing under shear load [Kip] 0.00 0.00
LC-1 NPC Eq. J3-6
Lc-end = Le - dh/2 = 1E300[in] - 0.8125[in]/2 = 1E300[in] Sec. J4.10
Lc-spa = s - dh = 3[in] - 0.8125[in] = 2.1875[in] Sec. J4.10
(1/W)Rn = (1/W)*(min(k1*Lc-end, k2*d) + min(k1*Lc-spa, k2*d)*(n - 1))*tp* Fu*nc
= 0.5*(min(1.2*1E300[in], 2.4*0.75[in]) + min(1.2*2.1875[in], 2.4*0.75[in])*(3 - 1))*
0.279528[in]*0[Kip/in2]*1 = 0[Kip] Eq. J3-6
Support
Web crippling [Kip] 0.00 0.09
LC-1 NPC Eq. J10-4
IsBeamReaction False
N = N = 17[in] Sec. J10-2
(1/W)Rn = (1/W)*0.80*tw2*(1 + 3*(N/d)*(tw/tf)1.5)*(E*Fyw*tf/tw)1/2 = 0.5*
0.80*0.279528[in]2*(1 +
3*(17[in]/11.984252[in])*(0.279528[in]/0.42126[in])1.5)*(30458.05[Kip/in2]*
0[Kip/in2]*0.42126[in]/0.279528[in])1/2 = 0[Kip] Eq. J10-4
WARNINGS
The torsion added to the
support weld due to axial is not included. It is recommended to bolt the connector to the
support.
------------------------------------------------------------------------
--------------------------------
Critical strength ratio NPC
------------------------------------------------------------------------
--------------------------------
NOTATION
Ab: Nominal bolt area
Ag: Gross area
Agv: Gross area subject to shear
Ant: Net area subject to tension
Anv: Net area subjected to shear
N: Bearing length
C: Bolt group coefficient
C2: Edge distance increment
d: Nominal bolt diameter
dcb: Bottom cope depth
dct: Top cope depth
dh: Nominal hole dimension
d: Beam depth
dhh: Horizontal hole dimension
dhv: Vertical hole dimension
D: Number of sixteenths of an inch in the weld size
E: Elastic modulus
e: Width of the leg of the connection angle attached to the support
FEXX: Electrode classification number
Fnv: Nominal shear stress
Fu: Specified minimum tensile strength
Fy: Specified minimum yield stress
Fyw: Specified minimum yield stress of web
g: Transversal gage between bolts
IsBeamReaction: Is beam reaction
IsCorrosionConsidered: Is corrosion considered
IsStressUniform: Is the stress uniform
k1: Bearing factor
k2: Bearing factor
k: Outside corner radius
L: Length
L: Angle length
Lc-end: Clear distance
Le: Effective length
Le: Edge distance
Leh: Horizontal edge distance
Lemin: Minimum edge distance
Lev: Vertical edge distance
Lh: Hole dimension for tension and shear net area
Lmax: Maximum length
Lmin: Minimum length
Lp: Plate length
edmin: Minimum edge distance
n: Bolts rows number
N: Bearing length
nc: Number of bolt columns
(1/W): Design factors
(1/W)Rn: Design or allowable strength
smax: Maximum spacing
smin: Minimum spacing
s: Longitudinal bolt spacing
Lc-spa: Distance between adjacent
holes edges
tp: Thickness of the connected material
T: Clear distance between web fillets
tf: Thickness of the loaded flange
tp: Plate thickness
tpmax: Maximum plate thickness
tw: Web thickness
Ubs: Stress index
wmax: Maximum weld size required
wmin: Minimum weld size required