Professional Documents
Culture Documents
Please read this user guide carefully before using the product.
Installation
A. Product Overview ........................................................................ 4
B. Preparing for use ......................................................................... 5
- Connector - Molex
- Power driver types
- Additional Check Points
C. Installation Guide ......................................................................... 6
- Procedure: Driver Connection - Rigid
- Connection Method - Schematic diagram
- Driver list
Technical Information
A. Product portfolio ......................................................................... 10
B. Spectrum .............................................................................. 15
C. Flux & Luminance vs. Current ........................................................................ 16
D. Lifetime ................................................................................... 17
E. Efficacy vs. Luminance ......................................................................... 17
F. CCT & Duv vs. Luminance ...................................................................... 18
G. IV Curve ...................................................................................... 18
H. Voltage vs. Temperature............................................................................ 19
I. Uniformity & Surface Temperature................................................................ 20
J. Angular Distribution ....................................................................... 21
- Lambertian angle distribution
- UV angle distribution
Reliability
A. Reliability test condition ........................................................................ 22
- Operation lifetime
Please note that the information given in this document is for your reference only,
and is not to be misconstrued as guaranteed data.
For the specifications of each product, please refer to the data sheet.
1 LG Display User manual
Handling Instruction
A. Handling and Safety
1. Unpack packing box with care. Remove packing trays gently and carefully from packing box.
2. During unloading and handling, gloves are required to prevent finger cuts or possible shocks.
Gloves are also required to avoid fingerprints being left on the glass, and to keep moisture
from causing corrosion to the metal traces.
3. Handle panels with caution. Mechanical stress such as shocks and pressures on the panel
surface (active area, encapsulation glass cavity area) must be avoided to prevent cracking of
the glass, delamination, scratching of the film, and internal structure damage. Do not press or
drop the panel.
4. During unloading and handling, panels should always be held from the side. Avoid direct
contact with metal contact pads or connector traces.
5. Protect the panel surface from scratches. Avoid direct contact on panel surface and do not
stack panels on top of each other.
6. Protect the corners and edges during handling, assembly or installation to prevent chipping
or breakage of glass.
8. Contact with water must be avoided to prevent damage of films and corrosion of metal
traces. Water drops must be wiped immediately.
9. To remove particle/foreign materials and surface stains, gently wipe the surface of the panel
with non-abrasive cloth.
10. In case of breakage, avoid direct contact with bare hands. Do not swallow particles, chips, or
materials.
11. For interconnections, spring contacts are recommended. Soldering and other
interconnecting technologies which apply heat to the panel may cause damage, and are
therefore not recommended.
12. Do not hold the panel on the surface. Hold the panel from the edge.
13. In case of connecting multiple panels, series connection is highly recommended. Panel to
panel uniformity problem can occur by parallel connection.
1. Store and operate OLED panels within the ranges specified in the product
specifications on page 11. Recommended temperature is at 25C; Recommended
relative humidity is below 70% (RH). (High temperature and humidity can cause film
degradation, bubble generation, and film delamination)
2. Store panels in the trays and ESD pouches as delivered from LG Display.
C. Disposition
LL167RS1 LL167FS1(Flexible)
Emitting side Back side Emitting side Back side
LL081RR1 LL081FR1
Emitting side Back side Emitting side Back side
LL124RR1 LL039RC1
Emitting side Back side Emitting side Back side
Plug Receptacle
OLED panel with plug connector Receptacle connector Plug and receptacle connected
LG LG LG
OLED OLED OLED
Output
Current Power Source
Input
(100 ~ 240 VAC) Connection Method
(Rigid Type Panels)
Type Rigid
Model LL056RS1-93P1 LL056RS1-74P1 LL081RR1-93P1 LL081RR1-74P1 LL159RR1-93P1 LL159RR1-74P1
Type Rigid
Model LL124RR1-93P1 LL124RR1-74P1 LL167RS1-93P1 LL167RS1-93P1 LL039RC1-93P1 LL039RC1-74P1
Type Flexible
Model LL081FR1-53P1 LL081FR1-54P1 LL159FR1-53P1 LL159FR1-54P1 LL167FS1-53P1 LL167FS1-54P1
Shape
400
200
100
100
50
50
Thickness*
0.88 0.88 0.88 0.88 0.88 0.88
(mm)
Efficacy
90 75 90 75 90 75
(lm/W)
CRI (Ra) 93
* with OCF
**Metal Film Encapsulation
***Cavity glass Encapsulation
Shape
300
300
= 100
100 300 (Diameter)
Thickness*
0.88 0.88 0.88 0.88 0.88 0.88
(mm)
Efficacy
90 75 90 75 90 75
(lm/W)
CRI (Ra) 93
* with OCF
**Metal Film Encapsulation
Shape
200
400
300
50
300
50
Thickness
0.41 0.41 0.41 0.41 0.41 0.41
(mm)*
Efficacy
55 50 55 50 55 50
(lm/W)
CRI (Ra) 93
* with OCF
**Metal Film Encapsulation
4,000K 3,000K
1.2 1.2
1
Normalized Intensity (a.u.)
0.6 0.6
0.4 0.4
0.2 0.2
0 0
380 480 580 680 780 380 480 580 680 780
Wavelength (nm) Wavelength (nm)
Luminance (cd/m2)
Luminous Flux (lm)
100 4000
75 3000
50 2000
25 1000
0 0
0 50 100 150 200 250 300 350 400 0 50 100 150 200 250 300 350 400
Current (mA) Current(mA)
2stack,3stack
80000
Over 70k
70000
60000 59k
Lifetime (hr)
50000
40k
40000
30000 29k
22k
20000 17k
14k
10000
0
1000 2000 3000 4000 5000
Luminance (cd/m2)
60 65
55 60
50 55
45 50
0 1000 2000 3000 4000 5000 0 1000 2000 3000 4000 5000
Luminance(cd/m2) Luminance(cd/m2)
CCT (K)
CCT (K)
4000 0
Duv
3000 0
Duv
3800 -0.002 2900 -0.002
Luminance(cd/m2) Luminance(cd/m2)
G. IV Curve
2stack 3stack
6000 6000
5000 5000
Luminance (cd/m2)
Luminance (cd/m2)
4000 4000
3000 3000
2000 2000
1000 1000
0 0
5.40 5.60 5.80 6.00 6.20 6.40 7.8 8 8.2 8.4 8.6 8.8 9
Voltage (V) Voltage (V)
10.00
2stack
9.00 3stack
Voltage @3000nit (V)
4.00
-10 0 10 20 30 40 50
Temperature (C)
40.0
Measuring Equipment
- CA-2000, Konica Minolta 37.5
35.0
Temp. ()
Method
32.5
- Optical camera measures the luminance of
each pixel at a right angle to the panel. 30.0 UV Seal
27.5 MFE*
- It generally takes about 5 minutes to reach
25.0
peak uniformity.
0 5 10 15 20 25 30 35 40 45 50
- The number of pixels depends on the size Time (min)
of active area; typically 1 pixel = 100mm2 Measuring Equipment
- Thermal burn camera, FLIR
- Luminous uniformity calculation formula: Time to reach maximum surface
U = [1-(Lmax-Lmin)/(Lmax+Lmin)] x100% temperatures (34 ~35 @3,000cd/m2)
- MFE* type panels: 5 minutes
- UV seal type panels: 15 minutes
45
3000K
4000K
40
temp. ()
35
30
25
1000 2000 3000 4000 5000
Luminance (cd/m2)
Surface temperature increases along with
brightness levels
2stack 3stack
Angle distribution for 2stack models is Angle distribution for 3stack models is shaped
similar to the Lambertian curve, with the in an ellipse with the ratio at approx. 1.05
ratio at approximately 1.02 Nit(cd/m2) x Active area x x Lambertian Ratio
= Flux (lm)
uv Angle distribution
Items Condition