Professional Documents
Culture Documents
Variable definitions
H = length of work day
W = off-route factor
h = haul time (1-way or round trip)
t1= time spent driving from dispatch site at beginning of day
t2= time spent driving to the dispatch site at the end of day
s = time spent at disposal site
N = # of trips made per day
v = volume of collection vehicle
r = vehicle compaction factor
c = container volume
f = average container utilization factor
Cn = average # of containers per location
Ct = # of containers serviced in a trip
Ct(max) = maximum number of containers the vehicle can hold - a function of truck
capacity, compaction, and the volume of waste per container = (v*r)/(c*f)
L = # of locations or serviced in the work day
Lt = # of locations serviced in a trip
Lt(max) = maximum number of locations servicable in a trip - a function of truck capacity,
compaction, and the volume of waste per location = Cmax /Cn
PSCS = time spent servicing containers each trip.
o Time spent loading and replacing containers and driving between locations
o Function of the # of sites serviced during the trip and the # of containers at each
location (an average value is used)
o Equations for calculating:
The following two equations are typically used when 'dbl' is large (ie -
commercial container systems or rural areas)
PSCS = Ct*(uc) + (Lt - 1)*(dbl)
PSCS(max) = Ct(max)*(uc) + (Lt(max) - 1)*(dbl)
uc = average time required to service one stationary
container, min/container
The next two equations are typically used when 'dbl' is small (ie -
residential container systems or dense urban areas)
PSCS = Lt*{dbl +k1Cn + k2*(PRH)}
PSCS(max) = Lt(max)*{dbl +k1Cn + k2*(PRH)}
dbl = average drive between location time, min/location
(typical value: ~0.72 min/location)
k1 = constant related to the service time per container,
min/container (typical value: ~0.18 min/container)
k2 = constant related to the time required to collect waste
from the back of a residence, min/loc/PRH (typical value:
~? min/location/PRH)
PRH = residences requiring back of house service, percent
The difference between the analysis of an HCS and and SCS is that in an HCS, the collection
vehicle hauls one container at a time to and from the disposal site while in an SCS the collection
vehicle (usually a packer truck) collects waste from as many containers as possible prior to
hauling the waste to the disposal site. The pickup time per trip (PSCS) is then a function of the
number of containers serviced on each trip and the time spent servicing each container.
Variable Definitions
Time Analysis
There is still only so much time availabe in a day to complete all of the tasks required for waste
collection and disposal. When a time analysis is conducted to determine the number of locations
which can be serviced by one packer truck in a day, the following steps are used:
1. The maximum number of containers and locations servicable per trip is calculated using
the effective volume of the truck and the amount of waste per container or site.
2. PSCS is calculated.
3. The number of trips possible per day (N) is solved for using the primary overall time
equation.
4. If N is an integer then the number of location is serviced is equal to N*Lt(max). If N is not
an integer then, goto Step 5.
5. When N is a non-integer, the trips done must be divided into complete and partial trips as
defined above.
1. Set N' equal to the integer portion of N calculated in Step 3. Rounding N down to
an integer value (N') gives the number of complete trips which can be done.
2. The fractional portion of N represents the time available to do a partial trip. To
determine how many locations can be serviced in this partial trip (Lt'), all of the
tasks involved in the full tripsmust be deducted from the workday, then the
remaining time must be analyzed to determine how much trash could be collected.
3. Solve the secondary overall time equation for P'SCS.
4. Solve the equation for P'SCS for Lt. Let this Lt = Lt'
5. The number of locations serviced then equals N'*Lt(max) + Lt'
Think: